Req help with fx5200-vtd128 no display out of box

new assembly, monitor cannot see card with either the reg vga or dvi with vga adapter.
-monitor does work, tested with other system
-ps appears good the fan on vga card turns
-cleaned pins and reseated
-mobo setup is correct i think, checked it 3 times. it
has 4 jumpers
-mobo appears ok but cannot confirm till later
- do not have additional system to swap test card in
thanks for any help or ideas
soltek nv400-l64 single channel
nforce2 400 north bridge
nforce2 mcp south bridge
nforce mcp 10/100 onboard lan
amd barton athlon xp 2500
512mb corsair cmx512 2700
msi fx5200-vtd128
xaser III 2k
450w ps
wd 80gb 7200 8mb
no os, just assembled

Just a thought - had a friend with an FX5900 on an nForce chipset which would not show anything on the display. Another VGA card put in its place had the same problem. The mobo (an MSI) had two jumpers to set it in safe mode (100Mhz bus speed). After flipping these into position and turning it on there was the display!!
Reset items in BIOS and jumpers and the system went on without problem. Maybe your board has the same jumpers.
Just a thought!

Similar Messages

Help with FX5200 VTD128 video capture

Hi all,
Just got this card - works great except video capture. When I try to use Windows Movie Maker, I get a message saying that the device is not responding, close any applciations that may be using the device & try again, then a message saying the device could not be used because there was an error starting the device. I have used MSI Live Update to get the latest drivers for this card. Also, I see a nVidia TV Tuner in my Control Panel - is this related to my problem?
Thanks!
Asus A7V
1.25 Gb PC133 SDRAM
FX5200 VTD128
Audigy 24-bit w/1394
LG DVD-Burner
1 x 40 Gb 7200RPM HD
1 x 120 Gb 7200RPM HD

Just a thought - had a friend with an FX5900 on an nForce chipset which would not show anything on the display. Another VGA card put in its place had the same problem. The mobo (an MSI) had two jumpers to set it in safe mode (100Mhz bus speed). After flipping these into position and turning it on there was the display!!
Reset items in BIOS and jumpers and the system went on without problem. Maybe your board has the same jumpers.
Just a thought!

I need help with XML Gallery Fade in out transition. somebody please help me :(

I need help with XML Gallery Fade in out transition. somebody please help me
I have my post dont want to duplicate it

The problem doesn't lie with your feed, although it does contain an error - you have given a non-existent sub-category. You need to stick to the categories and sub-categories listed here:
http://www.apple.com/itunes/podcasts/specs.html#categories
Subscribing to your feed from the iTunes Store page work as such, but the episodes throw up an error message. The problem lies with your episode media files: you are trying to stream them. Pasting the URL into a browser produces a download (where it should play the file) of a small file which does not play and in fact is a text file containing (in the case of ep.2) this:
[Reference]
Ref1=http://stream.riverratdoc.com/RiverratDoc/episode2.mp3?MSWMExt=.asf
Ref2=http://70.33.177.247:80/RiverratDoc/episode2.mp3?MSWMExt=.asf
You must provide a direct link to the actual mp3 file. Streaming won't work. The test is that if you paste the URL of the media file (as given in the feed) into the address bar of a browser it should play the file.

Need help in modifying mapping parameters of out the box mapping

Hi There,
I am a new bee to dac.
Need help in modifying mapping parameters of out the box mapping, which is invoked by DAC task.
We got a requirement to edit mapping parameter. When I go and see parameter under mappings tab in a mapping, I could not see any values in it.
But when I set any value, and validate it. It is successful.
Is it right way to do it?
What my concern is, When I initially go and see parameter values under maapings tab in a mapping, they are blank.
Where is it storing these values?
Thanks,
Rag

If you modify mapping then u have to create new task in dac and dac itself craete parameter file at run time. if you want to add more parameters then do it in dac system parameters tab.
Thanks
Jay.

Help with Title and Author Displaying on the iBooks Bookshelf.

I have created a book using iBooks Author and connected my iPad to my iMac to Preview my book, the book previews correctly the information I have entered into iBooks Author, however when you look on the iBooks Bookshelf it says UNKNOWN TITLE and UNKNOWN ARTIST even though I have entered this on my title page in iBooks Author, however the icon of my book on the iBooks Bookshelf is showing correctly the photo on the cover and the title and author, can any one help with this please?
Also no Category is showing against my book onthe iBooks Bookshelf how do I add one please?

To be honest, you should really put this under a seperate post of your own, but I'm not here to whine...
It sounds that you haven't defined the book title yet.
Open your book in iBooks Author and go to the panel on the left-hand side of your screen that shows your page thumbnails. Scroll to the top of this box, and find the panel that has the:
Book Title
Intro media
Table of contents
Glossary.
If your Book Title here says simply 'Book Title', then define it by double-clicking on the 'Book Title' text in the thumnails panel, and type in your book's title.
HTH.

Help with if/else in displaying data - (possibly foreach)

Hello all,
I've been trying to set something up, and I'm having difficulty getting it to work.
Lines 84-111 have become my biggest difficulty. I've got an if/else statement set up so that if one record has an image located on the localhost that image is pulled up. The way I have it now, this works great.
If I swap lines 93-96 with 102-105, and just tweek line 90, I can get it to work if the image is located on an alias and not the localhost.
The problem is that if I have it like it is now, I can't get both to work at the same time. So, I'm trying to get the if/else statement to apply to each record that is being pulled up. It seems like what it is doing now is choosing which part of the if/else statement it needs to use for the first record, and then applies that for all records.
Is there a way to have it coded like it is now for the if/else statement (because I want to be able to add multiple alias' and just check to see if the image is on the localhost or not); but have the image be displayed no matter if the image is located on the localhost or an alias?
The following is what I've got so far:
<?php
$search = $_GET['series'];
$query_begin=" SELECT * FROM movies WHERE movie_name_series = '$search' ";
$search_begin = mysql_query($query_begin) or die(mysql_error());
$row_begin = mysql_fetch_assoc($search_begin);
if($row_begin == 0){
?>
<script type="text/javascript"></script>
<?php
else
                $query_display = "SELECT * from series WHERE series_id = '$search'";
       $result_display = mysql_query($query_display);
       $row_display = mysql_fetch_array($result_display, MYSQL_ASSOC);
          $series_id = $row_diaplay['series_id'];
          $series_name = $row_display['series_name'];
    ?>
<h2>All Movies in our Library categorized in the series <?php echo $series_name ?></h2>
<br />
<div style="float: left; width: auto">
    Click on the name of the movie to edit the movie.
</div>
     <br />
        <hr size="1" noshade="noshade" />
<br />
<?php
$query="SELECT * FROM movies
INNER JOIN family_rating ON movies.movie_star_rating=family_rating.star_id
INNER JOIN alias ON movies.alias=alias.alias_id
INNER JOIN parent_alert ON movies.parent_alert=parent_alert.alert_id
INNER JOIN rating ON movies.movie_rating=rating.rating_id
WHERE movies.movie_name_series='$search'
ORDER BY movies.movie_name ASC";
$result= mysql_query($query)or die (mysql_error());
while($row=mysql_fetch_array($result)){
// Display the data
?>
    <table width="200" style="margin: 20px">
    <tr align="center">
<td valign="top">
   <h1 style="font-size: 12px"><?php echo $row['movie_name']; ?></h1>
        </td>
    </tr>
    <tr align="center">
<td valign="top" style="width: 100%; border-bottom: ridge #FFF; border-left: ridge #FFF; background: url(assets/images/transback.png) repeat; padding: 10px">
   <a class="ToolText" onMouseOver="javascript:this.className='ToolTextHover'" onMouseOut="javascript:this.className='ToolText'">
   <style media="screen" type="text/css">
          #coverart {
            display: block;
            width: 110px;
            height: 150px;
          #coverart:hover {
            background: url("assets/icons/play_movie.png") no-repeat 0 0;
          background-size: 110px;
         </style>
        <p>
         <form action="index.php?content=play_movie" method="post">
            <input type="hidden" value="<?php echo $row['movie_id']; ?>" name="movie" />
         <input type="hidden" value="<?php echo $row['warning'] ?>" name="warning" />
                                    <?php
          if ($row['alias_name']='localhost') {
         ?>
                                    <input onmouseover='this.src="assets/icons/play_movie.png"'
                                     onmouseout='this.src="movies/coverart/<?php echo $row['art']; ?>"'
                                    type="image" src="movies/coverart/<?php echo $row['art']; ?>"
                                    style="border: none" height="150" width="110" />
                                    <?php
          }else{
           ?>
                                    <input onmouseover='this.src="assets/icons/play_movie.png"'
                                     onmouseout='this.src="http://<?php echo $row['ip_address']; ?>/<?php echo $row['alias_name']; ?>/coverart/<?php echo $row['art']; ?>"'
         type="image" src="http://<?php echo $row['ip_address']; ?>/<?php echo $row['alias_name']; ?>/coverart/<?php echo $row['art']; ?>"
                                    style="border: none" height="150" width="110" />
                                    <?php
          ?>
            </form>
                                    </p>
                                <span><h2 align="center"><?php echo $row['movie_name']; ?></h2>
        <?php echo $row['rating_name']; ?>
                                <h4><?php echo $row['description']; ?></h4>
        <?php
         if($row['parent_alert']='1') {
          ?>
        <p align"center"><img src="assets/icons/<?php echo $row['alert_file_name']; ?>"></p></span>
                                <?php
         } else {
         ?>
            </a>
            <img src="assets/icons/s_<?php echo $row['star_file_name']; ?>" />
        </td>
</tr>
    </table>
<?
?>
I've looked through a number of tutorials and it's been indicated to use a for each loop. However, I can't seem to get this to work. Is there anything I can do to get this to work the way I am trying to? Is it a problem with my if/else or do I need a for each? If I need a for each, how do I do that?
Thanks.

Thank you for your reply. I apologize for not being as clear as I needed to be, so I'll try and explain better.
I've got a page that pulls up some records from a database, where I've got an if / else statement as part of the section where it displays the data.
                                    <?php
          if ($row['alias_name']='localhost') {
         ?>
                                    <input onmouseover='this.src="assets/icons/play_movie.png"'
                                     onmouseout='this.src="movies/coverart/<?php echo $row['art']; ?>"'
                                    type="image" src="movies/coverart/<?php echo $row['art']; ?>"
                                    style="border: none" height="150" width="110" />
                                    <?php
          }else{
           ?>
                                    <input onmouseover='this.src="assets/icons/play_movie.png"'
                                     onmouseout='this.src="http://<?php echo $row['ip_address']; ?>/<?php echo $row['alias_name']; ?>/coverart/<?php echo $row['art']; ?>"'
         type="image" src="http://<?php echo $row['ip_address']; ?>/<?php echo $row['alias_name']; ?>/coverart/<?php echo $row['art']; ?>"
                                    style="border: none" height="150" width="110" />
                                    <?php
          ?>
When the records are pulled, it seems like only the first part of the if / else statement is being applied to every record that is being pulled. The problem is if I've got records like the following:
Record one - (file on the host computer)
needs to be displayed from the condition
src="movies/coverart/<?php echo $row['art']; ?>"
Record two - (file on networked external hard drive)
needs to be displayed from the condition
src="http://<?php echo $row['ip_address']; ?>/<?php echo $row['alias_name']; ?>/coverart/<?php echo $row['art']; ?>
The way it's coded now, only record one will display the image (record two will not display the image). If I swap the order of the conditions, only record two will display the image (record one will not display the image).
How do I get both record one and record two to display the image when both appear on the same page from a single search query?
If I still did not explain it well enough, please let me know and I will try and do better. Again, thank you for your help.

Need a little help with a Jbutton not working out the way I planned

The following code is to fulfill an assignment I am working on. The problem I am having is with the btnCalc. For some reason when the button is used, the results I get is from another button. I think the variables are set right for the program to function properly but I am really hung up on this. Do anyone have any suggestions?
import java.awt.*;                     //Contains classes for creating GUI
import java.awt.event.*;                //For listener events
import javax.swing.*;                     // Imports the Main Swing Package
import javax.swing.event.*;
import javax.swing.text.*;           // Positions text box
import java.text.NumberFormat;          // For number format such as currency
import java.text.*;                     // Imports the Main Text Package
import java.util.*;                     // Utility Package
public class MPC extends JFrame implements ActionListener           //Creates Class for MPC
//double dblLoanAmount, dblInterestRate, dblMonthlyPayment;
TextField txtTotalMort;
     //JButton fixRates = new JButton("Choose Fixed Rates");
     JLabel lblTotalMort = new JLabel("How much is the loan?"); // Label for dblLoanAmount amount
     JTextField txtYears = new JTextField(10);
     JLabel lblPayment = new JLabel("Your monthly payment is "); // Label for Payment
     JTextField txtPayment = new JTextField(10);
     JLabel lblYears = new JLabel("How many years?");
                         // add(lblYears);
               JTextField txtYearsInput = new JTextField(10);
                         //a dd(txtYears);
     JLabel lblInterestRate = new JLabel("What is the interest rate?");
                         //add(lblInterestRate);
               JTextField txtInterestRate = new JTextField(10);
                         //add(txtInterestRate);
     //JLabel lblPayment = new JLabel("Your monthly payment is:");
                         //add(lblPayment);
               //JTextField txtPayment = new JTextField(10);
                         //txtPayment.setEditable(false);
                              //add(txtPayment);
     JButton btnCalc = new JButton("Calculate");
                         //add(btnCalc);
                         //btnCalc.addActionListener(this);
JButton year7InterestRateBtn = new JButton("7 years at 5.35%");     // Mortgage Term and Interest Rate
JButton year15InterestRateBtn = new JButton("15 years at 5.50%");
JButton year30InterestRateBtn = new JButton("30 years at 5.75%");
JButton reset = new JButton("Clear All");
JTextArea boxSpace = new JTextArea(100,200);          // Morgtage table size
JScrollPane scroll = new JScrollPane(boxSpace);     // ScrollPane
          public MPC()     // Method
     super("MPC");     // Frame Title
          JMenuBar mb = new JMenuBar();     // Menu Bar
setJMenuBar(mb);
                    setSize(325, 500);          // Frame Size
                    JPanel pane = new JPanel();
                    pane.setLayout(new BoxLayout(pane, BoxLayout.Y_AXIS)); //Grid box configuration
                    Container grid = getContentPane();
                    grid.setLayout(new GridLayout(8,2,8,8));     // Grid Layout
                    pane.add(grid);                                        // Adds grid
                    pane.add(scroll);                                   // Adds scrollPane
               grid.setBackground(Color.white);
                    Setting color of text and backgrounds
               txtYears.setBackground(Color.white);
          txtYears.setForeground(Color.black);
               txtYears.setFont(new Font("Arial", Font.PLAIN, 10));
                    txtPayment.setBackground(Color.white);
               txtPayment.setForeground(Color.black);
          txtPayment.setFont(new Font("Arial", Font.PLAIN, 10));
               boxSpace.setBackground(Color.white);
               boxSpace.setForeground(Color.black);
               boxSpace.setFont(new Font("Arial", Font.PLAIN, 10));
          grid.add(lblYears);
          grid.add(txtYearsInput);
          grid.add(lblInterestRate);
          grid.add (txtInterestRate);
          grid.add(lblTotalMort);          // Adds the Mortgage Amount Label
          grid.add(txtYears);               // Adds the Mortgage Amount Text Field
          grid.add(lblPayment);           // Adds the Payment Label
          grid.add(txtPayment);           // Adds the Monthly Payment Text Field
               txtPayment.setEditable(false);          // Disables editing in this Text Field
          grid.add(btnCalc);
     grid.add(year7InterestRateBtn);               // Adds 1st Loan and Rate Button
          grid.add(year15InterestRateBtn);          // Adds 2nd Loan and Rate Button
          grid.add(year30InterestRateBtn);          // Adds the Exit Button
          grid.add(reset);                               // Adds the New Calc Button
          setContentPane(pane);                          // Enables the Content Pane
          setVisible(true);                               // Sets JPanel to be Visable
          reset.addActionListener(this);                          // Adds Action Listener to the New Calc Button
          txtYearsInput.addActionListener(this);
          txtInterestRate.addActionListener(this);
          btnCalc.addActionListener(this);
     year7InterestRateBtn.addActionListener(this);                              // Adds Action Listener to the 1st loan Button
          year15InterestRateBtn.addActionListener(this);                              // Adds Action Listener to the 2nd loan Button
          year30InterestRateBtn.addActionListener(this);                               // Adds Action Listener to the 3rd loan Button
          txtYears.addActionListener(this);                              // Adds Action Listener to the Mortgage Amount Text Field
          txtPayment.addActionListener(this);                              // Adds Action Listener to the Monthly payment Text Field
          public void actionPerformed(ActionEvent e)                               // Tests to Verify Which Button is Pressed
     Object command = e.getSource(); // Enables command to get data
     int intYears = 0;          // Declares intYears
               double dblLoanAmount, dblInterestRate, interestRate, intRate;
     if (command == year7InterestRateBtn)                                   // Activates the 1st Loan Button
intYears = 0;                                        // Sets 1st value of Array
     if (command == year15InterestRateBtn)                                   // Activates the 2nd Loan Button
     intYears = 1;                                        // Sets 2nd value of Array
          if (command == year30InterestRateBtn)                                   // Activates the 3rd Loan Button
               intYears = 2;                                        // Sets 3rd value of Array
               if (command == btnCalc)
                    //dblLoanAmount = Double.parseDouble(txtTotalMort.getText() ); // Loan amount
                    //interestRate = Double.parseDouble(txtInterestRate.getText() ); // /100 )/ 12; // Devides rate
                    intRate = (Double.parseDouble(txtInterestRate.getText() )/100 )/ 12;
                    //int intYearsMonths = Integer.parseInt(txtYearsInput.getText() );// * 12; //Multiplies loan length
                    int months = Integer.parseInt(txtYearsInput.getText() )* 12;
dblLoanAmount = 0;                                   // Declares and Initializes dblLoanAmount
               dblInterestRate = 0;                                        // Declares and Initializes dblInterestRate
          double [][] dblTrmLoanRate = {{7, 5.35}, {15, 5.50}, {30, 5.75},};           // Array Data for Calculation
try
dblLoanAmount = Double.parseDouble(txtYears.getText()); // Gets user input from txtYears Text Field
catch (NumberFormatException nfe)                          // Checks for correct user input
                         JOptionPane.showMessageDialog(null, "You must enter a valid number.", "MPC", JOptionPane.INFORMATION_MESSAGE);
return;
          interestRate = dblTrmLoanRate [intYears][1];
               //dblInterestRate=interestRate;
               intRate = (interestRate / 100) / 12;                         // Calculates Interst Rate
     double intYearsMonths = dblTrmLoanRate [intYears] [0];                    // Calculates Loan Term in Months
int months = (int)intYearsMonths * 12;                          // Devides by months
double interestRateMonthly = (intRate / 12); // Devides Rate
          double payment = dblLoanAmount * intRate / (1 - (Math.pow(1/(1 + intRate), months))); // Calculates monthly payment
     double dblRmnLoan = dblLoanAmount;                              //Left over balance
     double txtPaymentInterest = 0;                                   // Payment
     double txtPaymentPrincipal = 0;                                   // Payment of principal
NumberFormat currency = NumberFormat.getCurrencyInstance(Locale.US); // Curreny format
     txtPayment.setText(currency.format(payment));
          boxSpace.setText("Month\tPrincipal\tInterest\tBalance Left\n");
          for (;months > 0 ; months -- )
          txtPaymentInterest = (dblRmnLoan * intRate);
                    txtPaymentPrincipal = (payment - txtPaymentInterest);          // Calculates monthly payment
               dblRmnLoan = (dblRmnLoan - txtPaymentPrincipal);
                    boxSpace.setCaret (new DefaultCaret());                    // Scroll position
                    boxSpace.append(String.valueOf(months) + "\t" +               // Table data
                    currency.format(txtPaymentPrincipal) + "\t" +
               currency.format(txtPaymentInterest) + "\t" +
               currency.format(dblRmnLoan) + "\n");
if(command == reset)
                         Clears fields
                    txtYearsInput.setText(null);
                    txtInterestRate.setText(null);
          txtYears.setText(null);
                    txtPayment.setText(null);
     boxSpace.setText(null);
                    public static void main(String[] args)                               //This is the signature of the entry point of all the desktop apps
          new MPC();
}

This portion to be exact. All the buttons work for me except this one. I need to calculate user input and also use the fixed data that can be found in the dblTrmLoanRate array. When I choos to use user input instead, the program either crashes or for some reason uses the year7InterestRateBtn instead.
               if (command == btnCalc)
                    //dblLoanAmount = Double.parseDouble(txtTotalMort.getText() ); // Loan amount
                    //interestRate = Double.parseDouble(txtInterestRate.getText() ); // /100 )/ 12; // Devides rate
                    intRate = (Double.parseDouble(txtInterestRate.getText() )/100 )/ 12;
                    //int intYearsMonths = Integer.parseInt(txtYearsInput.getText() );// * 12; //Multiplies loan length
                    int months = Integer.parseInt(txtYearsInput.getText() )* 12;
I was going to leave out the remed portion but thought it might help you with the navigation. I am sorry I did not use code tags, but I am going to go find out what those are and use them in the future.

Image files with large pixel dimensions display out of focus in a Bridge viewer?

I Create image files with pixel dimensions 2048x1365. When I display these files from Bridge on my Mac, either by pressing the space bar or in a slideshow, the images are out of focus. If I left click or click/hold and move the images slightly on screen they display in sharp focus. Unfortunately, although landscape-orientation images display correctly with no change in position or size, portrait-orientation files are enlarged and display with top and bottom off the screen. The pixel dimensions of my monitor are 2450x1600 so, yes, if portrait images are displayed at 100% they should display off screen, but this does not excuse the out of focus display of landscape files on this large screen. Nor does this explain why the portrait files are out of focus when they fit on screen. When the same files open in a Camera Raw window they are in focus. When they open in Photoshop at 100% the files are in focus.

Hi, Clay. Photoshop.com has its own forum, so you might want to post this there:
http://forums.adobe.com/community/photoshopdotcom

Need little help with JPA code and displaying database data into tables

Hello Everyone,
I am using java6 and Netbeans 6.1 on Windows XP platform.
This is probably very simple but have'nt been able to figure it out yet. I am using the Travel Java Databse included in NB6 as a learning tool.
I have a JComboBox connected to Person Table and want to display a Trip table from using the selected item from theJcombobox. In other words, Trip table shows only the Person selected from the Jcombobox.
If someone could point me on the right direction how to code JPA code or how to use NB6 GUI to accomplish this.
Thanks

The w and wi are just table aliases that make it easier to
referrence those tables by column when joining multiple tables
(avoids having to prefix column names with the entire table name,
etc.) When doing a self-join (joining a table to itself), the use
of table aliases is
required, otherwise you would have no other way to tell
which column belonged to which "instance" of table.
The query itself is pretty simple. It is just using a
correlated subquery to select only those instances of
workstationApps where the count of appID instances in
workstationAppIndex is less than the amount specified in the
maxConcurrentInstalls for the same appID.
Also, I do see what you are doing with #form.searchType#, I
was just making sure that it was what you really intended to do.
Phil

Help with Dynamic Code not displaying only ASP Shields???

Started working with some .asp pages today and it is not showing me the record set in the brackets. Like this {Recordset.Field} Only giving me the little ASP shield. Looks like this. I have search on google and in dreamweave in the pref's thinking something was not turned on. Can any one help this is driving me nuts.
theDogger

I have been working with DW since UltraDev days and I have never had this issue. I did a fresh install of Win7 Pro and now I get this instead of the dynamic info in the window. I really do not think that it matters what view you are in. I do not want to se what is generated by the DB I just want to see what is supposed to be re-ferenced by the DB in the WYSIWYG.It should not matter if I am working in the Designer or classic or what I usually work in the Dual Mode
It is killing me becasue I can't apply style to the shields it won't let me.
If I run live view I get the proper info. displayed but I should get something like this in the WYSISYG window {rs_innentory.inv-LG-Image} not the damn ASP shield.
I know that I am missing something simple that a tick box or something....it is driving me crazy!
theDogger

Help with image query and display

I want to show clients a few proofs. I've created a dropdown
list of Projects. That calls a CFC query to search for the related
image names within the DB. The images are stored locally/within my
Flex Application File Folder Structure. After querying the DB I
need it to return the list of images, and then display them from
the folder location. Can this be done and how? So far I can't even
get my CFC to return an Alert.show(imageList).toString(); So... I
missing something somewhere. I had to change the returntype to
query... but I've got a variable set as an imageList:image;??? Any
help or comments would be greatly appreciated!

The validator gives sound information about most
non-compliant code. For
example, the No Doctype error is an easy fix, and will
eliminate many of the
others.
Have you done anything to fix the problems ? Take the errors
one at a time
and please let us know each one you have difficulty with. You
will have to
learn some CSS to resolve some of the "errors".
"rachel_c" <[email protected]> wrote in
message
news:fj9gkv$pv4$[email protected]..
> Hello all,
> Would anyone help me in correcting the error codes on my
internet site :
>
http://jeanmichel.labarre1.free.fr
>
> I have had a look to recommendations about using the
>
http://validator.w3.org/
> but I have absolutely no idea of what changes I must
make in the code.
> I have used dreamweaver 8 and do not know much about
coding.
> The problems I encounter is that the display is
incorrect in netscape,
> mozilla... (lots of space in between text) whereas it
appears correctly in
> IE 6.
>
> Thanks a lot for your time!
> Rachel
>
>

I need help with my phone getting it out of recovery mode

i need help getting my iphone out of recovery mode

Placing your device into recovery (DFU-Device Firmware Upgrade) mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
   1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the
       other end of the cable connected to your computer's USB port.
   2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds
       until the red slider appears, then slide the slider. Wait for the device to turn off.
              * If you cannot turn off the device using the slider, press and hold the
                Sleep/Wake and Home buttons at the same time. When the device turns off,
                release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the
       device. The device should turn on. Note: If you see the battery charge warning,
       let the device charge for at least ten minutes to ensure that the battery has some
       charge, and then start with step 2 again.
4. Continue holding the Home button until you see the "Connect to iTunes" screen.
       When this screen appears you can release the Home button:
5. If necessary, open iTunes. You should see the following "recovery mode" alert:
6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
If you have a problem getting into recovery mode then try: RecBoot: Easy Way to Put iPhone into Recovery Mode.
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Help with DisplayPort to HDMI display settings

I am using a 50" Sony LCD TV with Mac Mini via DisportPort to HDMI adaptor. I am getting parts of the Dock and none of the top menu bar, why? The only setting that looks right is setting the display output to 1080x720 (overscan on). Any other settings will not fit the screen and crops both top & sides. Here are the TV specs. What am I doing wrong?
Sony's Description
Compared to enhanced definition televisions and other technologies, the Grand WEGA TVs deliver natural color reproduction and exceptional brightness levels due to 3LCD technology with *1280 x 720 native 720p resolution*.

The only time I can choose a PC setting is if I plug it in the VGA port. The problem with that is that it will not fill the screen no matter what combination of TV, and Mac OS X settings & that's why I am using a DVI to HDMI cable. Video looks pretty good, but text looks horrible.
What can I do to improve the look of text so when I browse safari I can actuallly read it. Right now all text on any white background looks like there is a RGB blur filter. Text on grey (like on system preferences), look like there is a blue & emboss filter. Is it possible to get my mac mini look incredible the way it would look if I hooked it up to a regular apple monitor using HDMI or is that just impossible? Video looks pretty good as I said so it's not bad for watching podcasts or Hulu, but it looks horrible when I want to Surf, and I don't know if my expectation to replicate what I see on an apple monitor is doable via HDMI with my 2006 Sony Bravia.

Need help with Cluster of Buttons displaying a message to which button is being pressed.

Create a VI with a cluster of six buttons labeled Option1…Option6. When executing, the VI should wait for the user to press one of the buttons. When a button is pressed, use the Display Message To User Express VI to indicate which option was selected. Repeat this process until the user presses the Stop button. The parameters of the problem needs me to use a while loop, case structure, a shift register and search 1d array. I'm just having trouble setting up my case structures and how to get the search 1d array to work with the cluster to find which button was pressed. I've attached a picture of my VI and also a VI I made without the cluster that does what I want the Cluster VI to do which is to recognize the button being pressed and bring up a prompt.
Solved!
Go to Solution.
Attachments:
Button Pressed.jpg ‏127 KB
Buttons Pressed No Cluster.jpg ‏189 KB

Okay so i moved the cluster into the while loop and wired a boolean true constant to the element of the search 1d array and now I can at least get the prompt for button 1 to display, but when I press the other buttons which I have set up the same way as button 1 I get no prompts so how can I get it to recognize the other buttons. Am I implementing the shift register incorrectly?
Attachments:
Button Pressed 2.jpg ‏115 KB

Help with transitions and fade in / out

I need help. I need some kind and infinitely patient personto explain, step by step, in simple words of less that one syllable how I can fade in my movie and how I can apply transitions between the clips.
I’ve tried, oh have I tried. I’ve read the manual, I’ve watched three video’s on youtube (they were bad!), found a lot of quality online help but I still don’t get it.
What I do get is random results. Like my movie fades in once then it won’t do it again. Like I get the grey transition box but can’t extend the transition beyond0.1 of a second. Like I trim my movie and the transition removes the trim. And so on.
So if some kind soul could help, or even point me in the direction of transitions made simple I’d appreciate it.
Many thanks.

Transitions and FCE are all about Media Handles.
Search this forum for mor info, you will find plenty.
Here's a start:
https://discussions.apple.com/message/1356445?messageID=1356445&amp%3b#1356445
This may help for Fade in/out settings:
https://discussions.apple.com/message/9037985#9037985
Al

Req help with fx5200-vtd128 no display out of box

Similar Messages

Maybe you are looking for