Req: K7T Pro MS-6330 and CPU

Pls, I have MSI K7T Pro motherboard. In support page there is written that this MB supports Duron up to 1.1 GHz and Thunderbird Athlon up to 1.2 GHz (100 FSB) with a little older BIOS 314 . Is the info true and recent or are there any news on it and it supports at least Duron 1.2 GHz or higher CPU ?

I have the MS-6330 v5.0 board Running an XP1900+ CPU (1.56GHz). The more recent BIOS images allow for higher CPU speeds, but it is important to check the version # of you board to verify the version of the BIOS falsh it can handle. With the v5.0 boards you can use BIOS v3.6 which allows 2200+ CPU's

Similar Messages

Were is the temp sensor on a k7t pro MS-6330

i have a k7t pro MS-6330 and would like to know were to "system" or "case" temp sensor is as i wana make sure it is not reading falesly (hiden behind a ribon cable etc (may be the msi H/G coul help)
cos i needed to know the anserw
( i've looked for it but dont even know what to look for ? )
please help someone!

An Athlon XP could run in your board but it would only run at about 75% of it's clock speed due to the fact your board doesn't support 266MHz FSB.
Officially you should only use a Duron1300 or old Athlon 1400/200 if you could still find one.
A 250w PSU could limit you depending on the rest of your hardware and the exact model/ratings of this PSU.

CPU help MSI K7T Pro ms 6330

will a AMD MOBILE ATHLON 4 1.2GHZ 200FSB AHM1200AQQ3B work on this board msi k7t pro ms 6330 ver 2.1

i dout it ,but to say no for sure you will have to try
its certainley not one msi ever tested in it

Problem with K7T Pro (MS-6330)

I've been used MSI K7T Pro (MS-6330) for 2 years and it worked just fine. But recently the problem occurred. After I've upgraded CPU from Duron 600 to TB 1.2 GHz, when I run a heavy-loaded application such as 3DMark, 3D games (UT2003) my computer will stop working (IMO: my case just like the classic K7T Pro) but when I touched the SC1155 chip, it just warm (it won't burn my finger). So I'm confused that is my mobo defected or not?
Oh, almost forgot .. my mobo was modified and can adjust multiplier.
FYI:
I've tried underclock CPU to 950 MHz and I've found that 950 work fine (or at least it use very long time to run full-loaded and then die). Once I forgot to plugged electric-cable for my heatsink fan and temp goes 66-68C and still working normally (not running 3D app.)
So, can anyone suggest me what is the problem with my mobo?
Thank you very much and apologize for my language :P
My Spec:
AMD Athlon (TB) 1.2 GHz (but now run @950MHz) VCore 1.55 (tried 1.55-1.85 result is the same)
MSI K7T Pro (MS-6330) modified to adjust multiplier
250W Powersupply
256 MB PC133
Winfast GF2MX 32 MB
SB Live! Value
Lite-on DVD16x
2 Harddisk (40GB and 4 GB)

Hi,
RMA the board, contact your nearest MSI office and ask for the RMA department.
There is not much more you can do.

K7T Pro (MS-6330)

I have a k7t pro and I want to get an athlon xp 1500+ in it. I know its not going to use the full potential of the processor but it is cheaper than an amd athlon 1.2 tbird.
I was running an amd x 1800+ on it before because i got it in a pulled system for free. it worked fine but will a 1500+ work stabily?

Dear Assaf !
'Since the K7T Pro only supports 200MHz FSB an AXP 1500+ (1333MHz) will only run at 1000MHz.'
This is true if you don't modify the processor.
On the other hand if you unlock the processor (paint the L1-bridges), paint/cut the L10 bridges and change the multiplier, then you can run the CPU at it's full speed.
I am currently running a XP1800+ (1533MHz) on a K7T Pro2 board with 102MHz FSB and a mult. of 16 (8 in BIOS +8 by CPU) at 1.63 GHz.
Regards,
/ErnyH

Msi k7t pro MS 6330 - best graphic card

hello gentlemen
As announce subject I am k7t pro ver1 owner. Nowadays the MB is provided with riva tnt2 model 64 - yeah it is old one. I would like to change the graphic card, up to the good one. So is there any graphic card you know may be recommend? Some VGA x4, having best technical parameters to the mainboard?
Kongo

thanks for reply
sure, I do not intend play newest games, anyway I wish to play hitmanII, or III and IGI-2 - some ! The MB I have is retired. Max CPU to the MB is 1.2G Athlon - and I fited out with it (1.2 Athlon). Power suply is powerful 350W of good make; also 448 sdr sdram is going to be. I just do not know if Geforce 4 will be suported by the MB. AGP port is 4x only.
Man, did I well anderstand you? You mean that if I plug in 8x graphic card the system wil be stable? Ex. MSI GForce 4 Titanium 4200 128DDR? And will work fine on the MB?
Anyway I wish to plug in as good as possible (or something about) graphic card... so are there any suggestion ?
Kongo

K7T pro (MS 6330) what is the highest CPU I can use?

I currently have a Duron 650 and the manual says that I can go up to ~1.3 Ghz. However, the CPU compatibility chart has an N/A beside anything higher than 1.2, even if it has a 100 FSB.
So my questions are: what is my limit, am I limited by a 250 watt power supply, does Athlon Thunderbird have much over the Duron, and will I see much difference from my 650 Duron?
I assume that the CPU has to be FSB 100 so Athlon XP or MP are out.
Thanks for any help.

An Athlon XP could run in your board but it would only run at about 75% of it's clock speed due to the fact your board doesn't support 266MHz FSB.
Officially you should only use a Duron1300 or old Athlon 1400/200 if you could still find one.
A 250w PSU could limit you depending on the rest of your hardware and the exact model/ratings of this PSU.

K7T Pro (MS-6330) BIOS freezes

Hello world!!!
my old PC (MSI K7T, AMD 650 MHz, 640 MB RAM) has worked fine until 4 days ago.
I switched off and from now I cannot switch on anymore.
Th 4 LED's stay always red, that means either CPU problm (???) or lithium battery problem.
I changed the battery (was almost discharged) but I cannot boot.
Any idea, tips, hint??
I have tried 3x to reset CMOS, still no success
Thanks a lot!!!

"How about this one, married to a Phenom X3 processor:
http://www.msi.com/index.php?func=prodcpu2&prod_no=1612&maincat_no=1
My guess it is about 100 $. A Phenom X3 about 150 $. And some memory too: Corsair TWIN2X PC6400 DDR2 2GB KIT CL4, 40 $ maybe."
Except for the processor there are chances you wont need a new PSU for the above. Suspect however you are in the upgrading mood, which points towards a new hard disk and DVD-burner (to house the videos you make) so allow for a Zalman PSU in your budget, too.
And a little off: Thank you, Svet Bosskov-killer for the back-up and information!
Mid a dodification: Was supposed to be a link in there, but got lost in translation. And misspelt last name.

Reboot vith k7t pro (MS 6330) under xp

I have installed xp and now when i want to stop my computer it always reboot
Mainboard k7tpro (MS 6330)
Duron 700 MHz
What is the version of bios i need ?
How to install this new version on my computer ?
:D

Hi!
You should be OK with BIOS version 3.2 (or higher if you have very large HDDs, for instance). You can find the instructions for flashing the BIOS here.
Hans

K7T Pro 2-A and memory upgrade

I want to upgrade memory on my MSI board. Now i have 384 MB of RAM, but i want to replace one 128MB module with an 512MB module. And I don't know what kind of 512MB module should I buy. Will 64Mx8 module work or should I find a 32Mx16 module.

...sorry for that not finished post.
I've also found, that there are 128Mx4 memory modules. So, what kind of module will surely work with my K7TPro-2A mainboard?
Best regards
Adam

K7T Pro 2 thermal issue, other than cpu

PLEASE EXCUSE NEW TO FORUM!!!
TRYING TO HELP A FRIEND FROM TOTAL UPGRADE!!!
SHE HAS A SYSTEMAX WITH THIS MB AND ATHLON 1000.
NEVER BEEN TWEAKED FROM FACTORY SETTINGS, STARTED HAVING INTERMITTENT CRASH PROBLEM 5-6 MONTHS AGO. I DETERMINED IT TO BE A THERMAL PROBLEM, AS IT WOULD RUN LONGER WITH THE SIDE COVER OFF, AND AFTER CRASH, WOULD REBOOT AND SEEM TO RUN, BUT NOT AS LONG.
I INSTALLED A NEW VOLCANO 7, USING ARTIC SILVER, BEING VERY CAREFUL, AND MAKING SURE OF PROPER INSTALLATION.
ALL PROBLEMS SEEMED TO BE REPAIRED, AND BEEN RUNNING FINE FOR LAST 3-4 MONTHS. NOW THAT SUMMER IS ARRIVING AGAIN IN ARIZONA, AND AMBIENT TEMPS ARE 80+ , IT HAS STARTED TO CRASH AGAIN. I'VE DOUBLE CHECKED ALL CONNECTIONS, CPU FAN SEEMS TO BE REGULATING SPEED FINE(VARIABLE), BIOS CAN BURN ALL DAY AND NEVER GO OVER 40 DEG. CEL.
AS BEFORE, REMOVING THE SIDE PANEL SEEMS TO ALLOW BETTER AIR FLOW, THEREFORE WILL SEEM TO BE OK, AT LEAST FOR A LONGER PERIOD.THE CPU FAN RUNS BETWEEN 3600-COLD TO ONLY ABOUT 4100 AT MOST HOT, AND CASE FAN AVERAGE 2700, NOT SURE ABOUT POWER SUPPLY FAN SPEED, BUT SEEMS TO BE DRAWING PLENTY OF AIR.
WHEN I "FEEL AROUND INSIDE" WHILE RUNNING, THERE DOESN'T APPEAR TO BE ANY EXCESS HEAT BUILD UP IN PROCESSOR AREA.
I NOTICE SYSTEMAX USES IT'S OWN VERSION OF AWARD BIOS, AND WONDER IF MSI AWARD BIOS FOR THIS BOARD CAN BE USED, AS MOST BIOS FEATURES ARE DISSABLED BY SYSTEMAX. I ALSO WONDER IS SYTEMAX MIGHT OVER CLOCK FROM FACTORY CAUSING THIS ISSUE.
I ALSO WONDER IF SOME OTHER COMPONENT IN THE MB MIGHT BE HEATING UP EXCESSIVELY, TO CAUSE A SUDDEN CRASH.
MB:K7T PRO 2 VER:1
CPU:AMD ATHLON 1000
GPU:TNT2 64
RAM:128MB PC133
SB:SOUND BLASTER LIVE
OS:WINDOWS ME
BIOS:AWARD 6.0
PS:NO BLUE SCREENS, WINDOWS SEEMS OK, WHEN IT CRASHES, SCREEN JUST GOES BLACK, BOTH INDICATORS FOR CPU AND HARD DRIVE STAY LIT (FRONT OF CASE), ALMOST ACTS LIKE IN STANDBY, BUT HAVE TO HIT POWER BUTTON TO RESTART

THANX FOR RESPONSE, UNFORTUNATLY THIS IS A BTO FROM SYSTEMAX, AND IT'S ABOUT 6-8 MONTHS PAST THE 2 YEARS, AND SYSTEMAX WANTS A SMALL FORTUNE FOR SUPPORT AFTER THE FACT, AND WOULDN'T YA KNOW IT, MY FRIEND SAYS IT STARTED THIS ABOUT A WEEK PAST THE WARRANTY PERIOD!!!!
I GUESS I KNOW WHAT NEEDS TO BE DONE, JUST FIGURED THIS TO BE A GOOD PLACE TO PICK SOME BRAINS, AND CONFIRM THAT I'M NOT JUST TOO HIGH TO FIGURE OUT THE PROBLEM!!!! I MIGHT BE AN OLD DOG, BUT I STILL LEARN A FEW NEW TRICKS, WHEN POSSIBLE. I HAVE PRETTY WELL DECIDED THE MB TO BE THE CULPRIT, IT JUST BOTHERS ME WHEN I CAN'T PINPOINT A PROBLEM LIKE THIS, AS NO MATTER WHAT PROBLEMS I MIGHT FIND, I LIKE TO FIND SOLUTIONS....JUST TOO DAMN CONVENIENT TO REPLACE PARTS, MORE FUN TO TRACK DOWN A SOLVE THESE PROBLEMS!!! :D

K7T Turbo2 MS-6330 Will not boot up

Can someone help, I have a K7T Turbo2 MS-6330, and it will not boot up, I know I have power to my MB, becasue when I plug it in, the lights on my DIMM chips light up, and my fan spins for about 1/2 second. I don't know what to check next. Any assistance would be appreciated.
THANKS...

First of all, write what hardware other than mobo you have: cpu, power supply, graphics, memory, etc.
also, read troubleshooting guide:
http://www.msi.com.tw/program/service/forum/index.php?threadid=1131&boardid=13&styleid=1
Take care

K7T Pro V1 sound problems and CPU support

I have a K7T Pro V1 motherboard.
I can´t use onboard sound, because when I try to locate it (Windows 2000) on Add New Device, appears blue screen and text "Hardware malfunction. Call your hardware vendor for support. The System has halted".
What I can do? ?( ?(
I also would like to know why this motherboard does not support Duron Morgan processors only Duron Spitfire -versions? :( :(
Thanks for your help!

I have enabled all in BIOS:
OnChipSound Enabled
OnBoardLegacy Audio Enabled
Soundblaster Enabled
The system does not found new device automatically and when if I try to find new device manually, appears that error message and I have to boot the computer again.
I just wonder is the problem onboard?
About CPU´s....
Rob454 told "...theyre not officially supporting the Duron Morgan Cpus".
Does this mean I can´t use Morgans att all (even 900 or 950)?
I mean does these 900 or 950 Morgans also need SSE support?
And if I´ll try to use for example Morgan 1.2 Ghz does it work att all (or read as Athlon Thunderbird)?

K7T PRO (6330) wasted?!

Can anyone help me out?
Today I bought an Athlon Thunderbird 1333MHz 133FSB for my old K7T-pro(bios v3.2) not knowing wether it would work or not.
At first the computer booted, but showed 1000MHz, I changed the CPU Host/PCI clock graduatly until my computer just stopped booting.
And here's the problem: After repeatedly switching the CMOS clear jumper, removed the battery(few minutes), switched to the old CPU(Duron 600), the system still won't boot. Some fans and leds works, but thats it.
Diagnostic LED status: X( X( X( X(
which should indicate CPU malfunction.
(I've reset the bios before succesfully for other reasons)
Have my overoptimistic CPU change wasted the motherboard, or are there other ways to reset it or whatever?

http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=97%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6330
one step beyond
try cmos and pull battery as well

K7T Pro and GeForce2 Ultra

I Probably haven't searched enough but I would like to know what you think. I purchased a GeForce2 Ultra 64mg for cheap. With the age of my board I would think it would work. The fan fires up but I have no output from the card. Is it a voltage issue? I remember something about this.
800mhz T-Bird
K7T Pro ver1:0
128mg Ram
TNT Riva 16mg
100mg (2 drives)
250 watt sparkle psu

Voltages are right on. I changed first display to agp but my little tnt card is agp and all works fine. Drivers aren't the issue as when I fire it up my monitor stays in standby. The other thing that happens is I get 4 red leds on my board. I thought that was cpu related. I get no trouble beeps. I'm going to take it to a local shop to test today. I'll post results. Thanks
800mhz T-Bird
K7T Pro ver1:0
128mg Ram
TNT Riva 16mg
100gig (2 drives)
250 watt sparkle psu

Req: K7T Pro MS-6330 and CPU

Similar Messages

Maybe you are looking for