Request for best connectivity Setup for WRT 1900ac. DHCP issue

Hello Customer Care Team.
I imported the WRT 1900ac router from the USA to my location in India. Apparently your Customer care in Indai don’t give any support for this fantastic router.
I am not at your mercy for assistance.
Please help & guide me in getting the best out of it and with a good setup.
MY ADSL+2 Modem Router : Netgear
Internet connectivity as follows:
Lan IP
192.168.1.1, subnet : 255.255.255.0
Dhcp server On : start: 192.168.1.2 End : 192.168.1.254
Wan IP Setup
PP0E LLC/SNAP NAT on
Wan Ip auto assigned
MTU: 1492
My Linksys wrt1900ac wireless is setup as follows for 2.4ghz & 5ghz
2.4 ghz 5ghz
Network mode mixed mixed
Security mode wPA2 WPA2
Channel width auto auto
Channel auto auto
Besides above WRT 1900ac has:
1. NAT enabled
2.Local network DHCP enabled as :
DHCP server enabled
Start IP: 10.185.21.100 end: 10.185.21.199
IP 10.185.21.X Range
3. Internet setting on WRT 1900ac as:
IPv4 Auto DHCP Configuration MTU Auto
I want you to tell me if my Linksys WRT 1900ac is configured correctly and the DHCP server IPs are correct.
When I enter 192.168.1.1 in the browser it takes me to my netgear modem web setup page. So How do I get to make all the modem & the wifi in the range of 192.168.1.1 etc.
Please help & provide your best solution for fast speed .
Thanks
Solved!
Go to Solution.

Sorry you didn't get an answer faster but you have to know this is a peer to peer forum. it is users helping other users so not always the quickest way. First off, can you change your ISP router to modem only mode? It is best that way as you will get conflicts such as what you are seeing when there are two routers in the same link. You are getting the ISP router when you enter 192.168.1.1 because that is its address on the LAN side. It appears that your router is getting set to a 10.x IP because of the setup. You have two routers trying to work with DHCP so that is also an issue. If you can change the ISP router to modem only mode then once it is up disconnect it from the router and do a factory reset on your router and make sure it has the IP of 192.168.1.1 and you will then be able to make any changes you need to. the default login is password of admin and leave the user blank.

Similar Messages

What is best connection setup for Airport Extreme?

I currently have the following configuration/setup:
Cable Modem > AEBS > 5-port switch.
Since all of my home networking is currently passing through my AEBS, I was wondering if I should setup as follows:
Cable Modem > 5-port switch > AEBS
Suggestions comments appreciated.
Regards,
Jim P.

Since all of my home networking is currently passing through my AEBS, I was wondering if I should setup as follows:
Cable Modem > 5-port switch > AEBS
No, if your cable modem is a simple modem.
No, even if your modem is a modem/router.....if.....you have a Gigabit Ethernet switch.....and..... you want to take advantage of the Gigabit Ethernet speeds of the Time Capsule

Best Multiprocessing setup for 24 Processor Cores & 64gb of RAM using new MacPro OSX 10.9.5.

Whats the best Multiprocessing setup for 24 Processor Cores & 64gb of RAM using new MacPro OSX 10.9.5.
I'm still getting an After Effects Warning: at the end of some renders saying "A frame failed to render using Render Multiple Frames Simultaneously.

Hi Szalam,
I'm using the latest After Effects (13.2.0.49)
See attached some screen grabs of my setup.

Error in CTC for BI Initial Setup for ABAP

Hi,
I have freshly installed BIJAVA 7.0 system and now i wanted to connect
with BW ABAP7.0 system which has been system copied from Qualtiy system.
While running the CTC template for BI Initial Setup for ABAP i am
getting following error :
" Validate Client : BW is already configured for different client. CTC
can be run only for that client. If BW has to be configured for the
client entered in 'Client' input field, perform Client copy using
transaction SCCL before running CTC template. "
I have used Java UME option during installation.Will it create any
problem.
Regard's
Goldy

Hi,
Hope you would have done all the post precessing after system copy.
Please check what are the entry maintained in the table mentioned below.
RSPOR_T_PORTAL
Change the entry in the above table in SM30 in backend and also check the settings in the portal
System Administration -> System Landscape-> SAP_BW
Thanks
Rishi Abrol

Looking for best apple software for image extraction i.e. select an image from one photo and place it on another photo

looking for best apple software for image extraction i.e. select an image from one photo and place it on another phot

Cannot guarantee it's the best, but it certainly is the least expensive:
http://www.gimp.org/downloads/

Best possible setup for the future

I am going to ask a generalized broad question. First some background, then I would appreciate your input.
Used mac desktops up until now. Primarily storage reasons. I am sending my daughter off to college this fall and decided to get our first laptop, nice zippy macpro 15". I have to say I'm very happy stealing this laptop from my daughter. I thought I would not want to do so much picture processing on such a limited screen, as I'm used to two landscape monitors.
The database for Aperture right now is almost 400 gigs. I used managed files. I initially thought about upgrading my old desktops to a new super powerful desktop in the next year of so, as I'm still using powermac PCs.
I wasn't going to consider a laptop as a serious contender for primarily the storage issue.
Enter thunderbolt.
Now I'm scratching my head and wondering about the potential to utilize this seemingly potential I/O as a game changer to the deal.
#1 - I'm not in a hurry. Time is on my side.
#2 - in the past, desktop Vs laptop was a no brainer to me. That gap has narrow now. The primary issue was screen space and storage, mostly storage/speed really.
#3 - speed gap from laptop to desktop is nominal at best from what I can tell, am I correct in seeing this now as not as clear an advantage of a desktop?
#4 - if I'm understanding thunderbolt right (and since time is on my side), I could potentially have a laptop with some lug around peripherals that would nearly make this like a desktop on the go. Sit down and plug into multiple monitors in a flash with RAID extensions, who knows what. Maybe then grab a raid cube and run with it to a place and essentially take my "desktop" environment with me. Am I thinking straight here or being a bit to idealistic? Seems like that it where Apple/intel is headed with this
#5 - managed Vs referenced. I've read a little about this debate and approach. I've only gone with managed and probably will do so, but in light of what I've said above, any comments?
#6 - backup. Always the biggie for me. backup. I love redundancy. I have time machine this and that thrown around in duplicity, copy over mirror drives here and there, and even put an extra drive or two in a neighbor's closet x2 a year just as an offsite backup in case of catastrophic loss like fire/theft. I'm not crazy over such a fragmented multiple approach, but haven't found what I consider a good alternative just yet to something simple, straightforward, and trustworthy. I'm hoping thunderbolt might lend a whole new ability to move quicker through backup scenarios. Thoughts? What are your approaches when you have a life's work of digital pics and videos and just can't stand the thought of ever ever losing them?
#7 - I would love to have an offsite online backup option for everything, seems that would solve so much of my backup stuff. But as a home user that is seriously into digital whatever, I haven't seem to run across something good as I've been limited to slow upload speeds. Until now. Enter FiOs. I can now(supposedly) do 32 up and down on the Fios, the fastest I think I will be able to get without going to a major business type connection. Does anyone have any knowledge of anything that would be a solid online backup option for 2TB or more of data on a revolving basis? I want to overshoot a bit as I seem to be picking up memory usage quickly with shooting in all RAW now and using higher density HD video. Opinions?
Having said all that, I hope what is coming across is that I'm looking at basically going from a guy who had an old powermac and found he is good at video, photos, and all things fun like that. Expanding into business sides of it slowly, seeming to have good luck, sending a daughter off to college introduced a surprising element to me of a powerful laptop, and now I'm grappling with onsite and offisite storage. Future expansion. thunderbolt potential.
I would appreciate some of you who have much more seasoned interactions with higher end equipment and can appreciate some of the details, if you could give some insight into what might work, might not, how to posture myself the best for future expansion and capabilities, etc. I'm not too worried about price. Obviously I'm a home user, so I don't have a corporate account. But dropping 10 - 20 grand in the next 2 or so years wouldn't be unreasonable if it were to posture me for the best potential use for many years.
Thanks,
Robert

TexasMan_Luvs_Hismac wrote:
The database for Aperture right now is almost 400 gigs. I used managed files. I initially thought about upgrading my old desktops to a new super powerful desktop in the next year of so, as I'm still using powermac PCs. I wasn't going to consider a laptop as a serious contender for primarily the storage issue.
#3: At the moment (until MPs are upgraded) the top new MBPs are stronger Aperture boxes than many Mac Pros are. IMO the first true desktop replacement (DTR) laptops. Stick to the stronger graphics options and I very, very strongly recommend the anti-glare display choice.
#5: Managed files are IMO not the way to go for many reasons, and certainly not on a laptop. I recommend using a Referenced-Masters-Library on the internal drive with Preview size set to be the size of your laptop display. Have two large external drives: one for Masters and Vaults and one for offsite backup of the other external.
So #6: Backup is easy, just add more off site drives for more redundancy and change them out frequently (at least weekly or every significant project). For images work mirrors tend to be a waste of drive space. Far more worthy is more frequent real offsite backup. Note that simple changeout of a 2-TB drive to the trunk of the car provides real backup against fire, theft and drive failure.
Originals should be backed up before import into Aperture or any other app anyway. A Managed-Masters-Library not only gets itself ridiculously large, having Masters in Vaults just makes Vaults huge and Vault backups slower, and therefore less likely to be done as frequently.
#4: Yes. Tbt may have some growing pains but I think your insight is accurate. However even without Thunderbolt using a Referenced-Masters-Library with Masters accessed over FW800 i/o is ok. Key is that the Library lives on an internal drive that is kept underfilled, which is easy once you use a Referenced-Masters-Library with Masters on external drives.
Personally I just ordered a 17" 2011 MBP with SSD and am replacing the optical drive with a 750 GB 7200 rpm OWC drive. The Referenced-Masters-Library will live on the SSD while Masters will initially live on the OWC drive then later get relocated to external archive drives.
#1 - I'm not in a hurry. Time is on my side.
Since you are using a Powermac now, I respectfully disagree. Life is short: get thee to a Sandy Bridge MBP asap This new MBP is literally what mobile Aperture users like me have been waiting for since v1.
HTH
-Allen Wicks

Best disk setup for Premiere CS6

Hello,
I want to improve my disk setup for Adobe Premiere CS6 because I got long loading times.
My current setup:
Crucial RealSSD C300 60GB SSD for the program
Samsung Spinpoint F3 1TB HDD for media and Media Cache Files
Samsung Spinpoint F3 1TB HDD for projects and exports
My planed setup:
new: Kingston SSDNow V300 120GB SSD for the program
Crucial RealSSD C300 60GB SSD for Media Cache Files
2x Samsung Spinpoint F3 1TB HDD with Raid 1 for media
new: Seagate Barracuda 2 TB HDD for projects and exports
Is this the best solution to improve the performance?
Thanks
Tim

What is the advantage of getting an extra HDD for the exports?
None from a performance point of view.
And should I use the 60GB SDD for the Media Cache Files?
That is much too small. Depending on your projects, you will need at least 256 GB, but possibly even more.
With only 350 GB of media and projects, my media cache is already 72 GB.
Read Harm's articles on disk setup, raids and balanced systems here: Tweakers Page

Requesting detailed config and setup for forecast 'period splitting'

I have searched the SAP community, and found little detailed information about configuration and setup for SAP forecast 'period splitting'.
I have selected the standard scenario in the 'Splitting Indicator' (1 - 2 - 4) in MM03/MRP3 for splitting month periods into weeks - AND - I have set the MRP Type found in MM03/MRP1 to 'VV' as specified (with "obligatory forecast indicator set on, which supports forecasts to be used as a basis for MRP).
Doing so has not resulted in my monthly inputted forecasts being split into weeks.
I am thinking that there is some missing configuration that is needed. Please advise if you can.
Thank you

Bert,
Now I am more curious than ever. You mention that your forecasts are not generated by SAP, but are generated by an external forecasting program, using requirements type VSF.
This sounds like your interface program is entering Planned Independent Requirements, not forecasts (for VV MRP type, the MRP element for forecast requirements is called "FORERQ" and not "IndReq"). The field to which you refer ("Splitting indicator" in the MRP3 tab) has no impact on Planned Independent Requirements. To my knowledge, it only works with the integrated forecast generation program that is commonly used in VV MRP type.
Best Regards,
DB49

XPS 2720 Question - best ssd setup for performance

Hi Guys
the 32gb msata on the motherboard that comes with the AIO, is this any good, want to upgrade ssd, do I keep msata but get larger or do I get rid of this and the 1tb sata 7200 and buy samsung 850 evo/pro and will this give me the best all round performance, interested what you think and what you would buy
next thing I will need is a dummies guide how to do this and i am not that technically minded,
1 important thing is I dont have recover disks and my backup/recovery does not work as it says I have corrupted environment, and dell does not detect my machine and when i input my service tag number it does not recognise that either.
what is going on,lol
regs
paul

The first thing you need is Windows 8.1 installation media, see here:
http://dellwindowsreinstallationguide.com/download-microsoft-windows-and-office/download-microsoft-windows/download-windows-8-1-retail-and-oem-iso/
Get a 250-500 GB mSATA and get rid of the 32 GB SSD cache drive. I prefer Crucial in particular the MX200 but Samsung are good also:
http://uk.crucial.com/gbr/en/compatible-upgrade-for/Dell/xps-one-2720
To install follow the instructions in the owner's manual to remove the mSATA mini-card:
http://ftp.dell.com/Manuals/all-products/esuprt_desktop/esuprt_xps_desktop/xps-27-2720-aio_Owner%27s%20Manual_en-us.pdf
Change the SATA operation to AHCI and wipe the HDD using DISKPART → CLEAN ALL:
http://dellwindowsreinstallationguide.com/ensure-you-have-the-correct-sata-configuration-in-the-bios-setup-for-your-configuration/sata-operation/
http://dellwindowsreinstallationguide.com/cleaning-up-a-drive-format-vs-secure-wipe-ssd-and-hdd/
Install Windows using a local account without a password (so your new factory image doesn't have your Microsoft Account associated with it):
http://dellwindowsreinstallationguide.com/a-clean-install-of-windows/a-clean-install-of-windows-8-1/windows-8-1-installation/
After installation of Windows you will need to install the system drivers (in the correct order):
http://dellwindowsreinstallationguide.com/downloading-drivers-checking-hardware-ids-and-downloading-and-installing-dell-system-drivers-in-the-correct-order/driver-installation/
Installation of Dell Backup and Recovery will make a new recovery partition from the clean install.
You may then want to switch to a Microsoft Account.
You will then want to initialize the HDD and migrate the user directories to it:
http://dellwindowsreinstallationguide.com/a-clean-install-of-windows/a-clean-install-of-windows-8-1/solid-state-drive-and-hard-drive-configuration/
You might want to look though the full guide (A Clean Install of Windows):
http://dellwindowsreinstallationguide.com/a-clean-install-of-windows/a-clean-install-of-windows-8-1/

The best HDD setup for my configuration

Hello! My desktop configuration:
Intel core I7-2600K
Gigabyte GA-Z68XP-UD3P
16 Gb RAM 1600 mHz (4*4Gb)
Inno 3D Nvidia GTX 580
I have 5 HDD in my system. What is the best way for Premier pro CS5.5 for this HDD's?
HDD 1 Kingston V200 256Gb SSD
HDD 2 Hitachi 1Tb 7K1000 7200 rpm SATA 3*2 (RAID 0)
HDD 3 Hitachi 1Tb 7K1000 7200 rpm SATA 3
HDD 4 Hitachi 1Tb 7K1000 7200 rpm SATA 3
HDD 5 Western digital 2Tb 7200 rpm USB 3.0 (External)

DeePeeeBee,
Very well explained, exactly the type answer I was looking for, so thank you for that.
On the IDE por of my MB, how do I get a SATA disk connected? a IDE to SATA converter cable? Sorry but IDE has not been in my way for a very long time.
I will defenetly post my results here and how I did it when done, hopefully other can benefit from my results.
So this is my current hardware set up and expecting to have time to put together by the weekend, ( actually the system has been running for more than a year now but I needed an upgrade specially for my HDD and monitors )
Graphic Card:
Nvidia Quadro FX 4800 VCQFX4800 ( I do not see many people saying good thing about this card except for expensive but I am very happy with the real time playback and the rendering time of this card)
CASE:
COOLER MASTER HAF 932 Advanced RC-932-KKN5-GP Steel ATX Full Tower ( Best case I have ever could buy 5 stars for me )
Board:
EVGA X58 FTW3 132-GT-E768-TR LGA 1366 Intel X58 SATA 6Gb/s USB 3.0 ATX
(Board is almost 2 years old but it is excellent board )
RAM:
G.SKILL Ripjaws Series 24GB (6 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
(Could have been better but I guess my budget was limited top that, also being used right now and performance is pretty good for me)
CPU:
Intel Core i7-950 Bloomfield 3.06GHz LGA 1366 130W Quad-Core
(At the time was my best choice since I could not aford a extreme edition cpu, I ma very happy with it so far.)
Cooler:
COOLER MASTER V8 RR-UV8-XBU1-GP 120mm Rifle (I hope I can find this cooler around when I buy for my next system, I may not need air conditioning in my studio, this cooler and the tower in conbination can only run at the lowest temp you can imagine, I have not noticed any warm air blowing out of my case, this is not real...I just have to say WOW!!! Love it)
HDD: 2 x Velocity Raptors 600GB 10K ( will use the Marvell chip for RAID 0 and will use this drive for media ... Capture, re-usable clips, sound, music and other pre-done effects and template for After effects, Encore audition and PS)
HDD: 3 x 1TB WD Caviar Black 7200 RPM ( Will use as RAID 0 on Intel chip, will be used
for output files, media cache for all adobe aplications and previous files )
HDD: Intel 120GB SSD drive version 520 ( will only have OS win7 and Adobe CS5.5 or maybe CS6 if I can soon budget an upgrade, MS Office and Roxio for ISO files and virtual drive)
Display:
2 x 22" Gateway Wide screen max resolution at 1650
(Getting these brand new and hopping they are a good choise)
Will post back.
Thanks
Luis

Best "Easy Setup" for AVCHD .mts files

I'm on a MacBook Pro in 10.5.8 with FCP 7, all footage is shot by a Canon HF S100 at 1920x1080 60i. Is there a best way to set up the Easy Setup for the AVCHD files?
I currently have it as:
Format: (all)
Rate: (all rates)
Use: Custom Setup
Sequence Preset: HDV 1080i60
Capture Preset: HDV Apple ProRes 422
Device Control: non-controllable device
Video Playback: none
Audio Playback: Default.
Is there a better way to do it than this?
Thanks,
Dave

Yup,
It costs but it's supposed to be very worth it on saved time and trouble.
http://www.clipwrap.com
From the website:
rewraps - doesn't transcode
ClipWrap rewraps the video samples from your existing m2t, mts, m2ts files without re-encoding them. This means blazingly fast convert speeds and no image degradation.
Transcodes too!
Need your files in ProRes, AIC, DNxHD or DVCProHD? ClipWrap can seamlessly convert your files. Don't worry about frame size changes, gamma shifts, or any of the other problems resulting from mismatched settings - ClipWrap chooses all those based on the source file's format.
Automatic format detection
ClipWrap speaks your camera's language so you don't have to. It automatically parses the file's format and chooses the proper output format, so there's no hassle trying to determine the proper settings (frame rate, image size, gamma levels, etc).
Full timecode support
Timecode is recreated in the new QuickTime movie, so you can recapture from tape later if necessary.
Supports HDV and AVCHD formats
Now you're not limited to specific HDV or AVCHD cameras, you can rest assured your files will be compatible with FCP when it comes time to edit.

Best connection process for oracel ADF?

hi all,
i am using oracle jdeveloper 11g 2 release and oracle database 10g. now i used database connecion in choosing Application resource type. i need to know what is the best way for connect with db? is it db connection ,JMX, URL, or WebDAV? because of i am going to make finally enterprise software for large company(4000 users use) .so number of users need to keep their connection because they are in different location. therefore show me what is the best path for keeping connection with oracle db? There is no any web service. so show me is there any connection method, because of timeout can be happen, server has poor connection?
thankx. all the best.

dear friend ,
ADF mean it is a framework(Application development framework). which is developed for java developers. earlier in oracle jdeveloper 10g used for development.now jdeveloper 11g has this feature.which is same to oracle forms,but it hasn't rports.it has jsf page(java sever face).jsp mean java server page. in adf both include but jsp is in jspx.java serve page xml.
read these lines:-
http://docs.oracle.com/cd/E18941_01/tutorials/jdtut_11r2_58/jdtut_11r2_58_1.html
http://www.oracle.com/technetwork/developer-tools/jdev/overview/index-100269.html
http://www.oracle.com/technetwork/developer-tools/adf/overview/index.html
http://www.oracle.com/technetwork/developer-tools/adf/learnmore/june2012-otn-harvest-1683085.pdf

TC firmware 7.3.2 versus 7.4.1! What's recommended for best connectivity?

for some time now my internet connections drops for no apparent reason and then comes back on. These interruptions last anywhere from 3 sec to several minutes.
I read somewhere that downgrading to Airport Utility firmware 7.3.2 helps.
Other suggestions were:
- deleting airport and internet related .plist files from the preferences folder.
- delete a apple.airport.kext file from the Extensions folder.
- switch channels in my 802.11 n (b/g) network.
Nothing of the above changed for the better.
here is what I gathered so far and tried myself based on numerous posts with people having similar problems:
Airport Utility> Wireless options:
- WPA Group Key timeout is set to 365 days,
- I use "Interface Robustness) (both under "wireless options") .
Under System preferences>Network settings:
- IPv6 is turned off,
- Airport is set on top of "service order.
- I deleted all other networks except for the one I am using.
Here is my basic set up:
I am on 10.5.6 and use a 1TB 1. generation TC. Backups run normally but the wifi connection (just 5 feet of direct though 2 windows). I am connected wirelessly though a PPPoE connection
Log in/ Start up items (under System Preferences>Accounts:)
I don't have a Realplayer in my start up items (as suggested as a potential problem in one of the forums)
can a change back to the older firmware help? or should I forget about the TC and reactivate my old and trusted 1. generation Airport Basestation?
thanks in advance for any advice

Thx Bob,
I tried the downgrading to 7.3.2 and it did not help matters.
I am not sure when or what exactly happened to make the TC act up.
I might go back to the old Airport Basestation if I don't find a solution here in this forum.
I talked to several Apple Care guys and had ISP folks check my modem.
any other suggestions?
thx

Best Hardware Setup for FLV Video Centered Standalaone

Can anyone recommend a system setup for a standalone app i'm
concepting that will have large and high quality (hopefully) flv
video playing as a background, hi-res png's or jpgs doing all sorts
of animation in the foreground and all while keeping a fairly high
overall framerate? my stage size is currently slated as 1024x768
BTW.
What's more/most important?
processor speed?
will a dual core help or not even be utilized (proposing
standalone with flash 8 runtime)?
will a suped up video card make a difference?
obviously the more RAM the better but is there a point where
that starts maxing out too?
any other considerations to note?
I'm curious to see what other users who've had a decent
amount of FLV centered projects have to say on the matter. Thanks
in advance
Pat

Can anyone recommend a system setup for a standalone app i'm
concepting that will have large and high quality (hopefully) flv
video playing as a background, hi-res png's or jpgs doing all sorts
of animation in the foreground and all while keeping a fairly high
overall framerate? my stage size is currently slated as 1024x768
BTW.
What's more/most important?
processor speed?
will a dual core help or not even be utilized (proposing
standalone with flash 8 runtime)?
will a suped up video card make a difference?
obviously the more RAM the better but is there a point where
that starts maxing out too?
any other considerations to note?
I'm curious to see what other users who've had a decent
amount of FLV centered projects have to say on the matter. Thanks
in advance
Pat

Best Easy Setup for 1080p?

Just got the new Canon and it captures video in 1080p H.264 Quicktime files. What is the best Easy Setup option since none match exactly to the captured format? The Apple Intermediate Codec at 720p seems to be the most accurate, is there an upgrade available to natively work with the 1080p files? To avoid excessive rendering, is it better to convert the original files in Quicktime Pro to another format? Final use will be to put on a DVD.

You can't use this camera with FCE without converting the material. Canon tried hard to make a great little video camera, but stupidly, in my view, chose to record at 30fps. Also it's in a H.264 proprietary video format that has to be converted to work smoothly in Final Cut.
You could use the QT pro player to convert it, or import and export from FCE. Not sure well i would handle the frame rate conversion which can be tricky. FCP will do a better job as you can work in ProRes or ProResHQ.

Request for best connectivity Setup for WRT 1900ac. DHCP issue

Similar Messages

Maybe you are looking for