[REQUEST] mplayer with eac3

Hi
there is a patch for ffmpeg and mplayer to finally playback eac3 audio from hd-dvd.
Could please somebody make a PKGBUILD for it? or modify the mplayer-svn and ffmpeg-svn PKGBUILD?
http://svn.mplayerhq.hu/soc/eac3/
http://forum.doom9.org/showthread.php?t=129050
thnaks
mic64

The FFMPEG patch does not build against current SVN. I'll take a look at it later and see if I can rewrite it.
See post #13 here:
http://bbs.archlinux.org/viewtopic.php? … 61#p284361
Last edited by skottish (2007-09-26 02:39:44)

Similar Messages

[Request] Mplayer with aac support.

Could someone make me a mplayer package with aac support? I can't seem to compile it because of Error: Bad gcc version.
EDIT: Never mind, fixed it.

Could someone make me a mplayer package with aac support? I can't seem to compile it because of Error: Bad gcc version.
EDIT: Never mind, fixed it.

[Request]MPlayer with vdpau support?

ftp://download.nvidia.com/XFree86/vdpau/
Someone who is good with PKGBUILDs who can make this? Would be appreciated if there where no gui compiled with MPlayer.

i have some error when i build this pkg
make: *** [mplayer] Error 1
+ return 1
+ ret=1
+ '[' 1 -gt 0 ']'
++ gettext 'Build Failed.'
+ error 'Build Failed.'
+ local 'mesg=Build Failed.'
+ shift
++ check_buildenv color
+++ in_opt_array color fakeroot '!distcc' color '!ccache' '!xdelta'
++++ echo color
++++ tr '[:upper:]' '[:lower:]'
+++ local needle=color
+++ shift
+++ local opt
+++ for opt in '"$@"'
++++ echo fakeroot
++++ tr '[:upper:]' '[:lower:]'
+++ opt=fakeroot
+++ '[' fakeroot = color ']'
+++ '[' fakeroot = '!color' ']'
+++ for opt in '"$@"'
++++ echo '!distcc'
++++ tr '[:upper:]' '[:lower:]'
+++ opt='!distcc'
+++ '[' '!distcc' = color ']'
+++ '[' '!distcc' = '!color' ']'
+++ for opt in '"$@"'
++++ echo color
++++ tr '[:upper:]' '[:lower:]'
+++ opt=color
+++ '[' color = color ']'
+++ echo y
+++ return
++ echo y
+ '[' -t 2 -a '!' '' = n -a y = y ']'
++ gettext ERROR:
+ printf '\033[1;31m==> ERROR:\033[1;0m\033[1;1m Build Failed.\033[1;0m\n'
==> ERROR: Build Failed.
++ gettext Aborting...
+ plain Aborting...
+ local mesg=Aborting...
+ shift
++ check_buildenv color
+++ in_opt_array color fakeroot '!distcc' color '!ccache' '!xdelta'
++++ echo color
++++ tr '[:upper:]' '[:lower:]'
+++ local needle=color
+++ shift
+++ local opt
+++ for opt in '"$@"'
++++ echo fakeroot
++++ tr '[:upper:]' '[:lower:]'
+++ opt=fakeroot
+++ '[' fakeroot = color ']'
+++ '[' fakeroot = '!color' ']'
+++ for opt in '"$@"'
++++ echo '!distcc'
++++ tr '[:upper:]' '[:lower:]'
+++ opt='!distcc'
+++ '[' '!distcc' = color ']'
+++ '[' '!distcc' = '!color' ']'
+++ for opt in '"$@"'
++++ echo color
++++ tr '[:upper:]' '[:lower:]'
+++ opt=color
+++ '[' color = color ']'
+++ echo y
+++ return
++ echo y
+ '[' -t 2 -a '!' '' = n -a y = y ']'
+ printf '\033[1;1m Aborting...\033[1;0m\n'
Aborting...
+ remove_deps
+ '[' 0 = 0 ']'
+ return
+ exit 2
+ clean_up
+ local EXIT_CODE=2
+ '[' 1 = 1 ']'
+ return

Multiple instances of mplayer with jack

"_R_ealtime software mixing ?!?! wtf thats awesome--actually im not a studio junkie, i just need sound on one of them"
i understand that the casual nature of my involvement with jackd suggests a less-than-appropriate level of respect and diligence for what this almighty app is capable of serving up. i just need to level audio volume on multiple instances of mplayer with software mixing (my sound card is cheap).
all my jackd configs are vanilla from the wiki as stated below. if anyone has another solution or a request for information in regard to this solution please reply. as always, thanks in advance
--here is some err... background
i have a some files that i would like to run with mplayer and a video file [with its own audio] that i would like to run concurrently. it should be possible to use jackd to let one instance of mplayer show video with no sound while permitting the audio from the other instance to play at arbitrary volume. without jack, i cannot control sound independantly since both instances seem to use the same device (PCM0). furthermore i have found that starting multiple instances of mplayer leads to weird artifacts which persist after all running instances of mplayer concurrent with artifact appearance have been closed.
so i installed jack-audio-connection-kit following the wiki verbatim. then i installed qjackctl. starting jackd as root and qjackctl with sudo allowed me to see the first instance of mplayer but not the second.
what is the difference between running mplayer through alsa and running mplayer through jack through alsa (not sure if the objects are accurately laid out there but whatever)? the wiki basically provides an out of the box solution for software mixing a bunch of inputs (i have friends who do sound professionally though not with linux and im envisioning way more complicated stuff than my humble pair of mplayers
Last edited by poopship21 (2010-09-25 15:20:56)

ngoonee wrote:
karol wrote:
ngoonee wrote:And running mplayer through alsa won't be able to do what you want, simply because the mixing is fixed. JACK and pulseaudio are sound servers which allow you to control the mixing, both can do what you want.
If you run one file with '-ao null' and the other one with '-vo null' you can manipulate them independently, there's no sound mixing involved, it just allows you "to add visuals to an audio feed spontaneously". They can both be run with 'af scaletempo' to speed up / slow down etc.
Hmm, wonder if that's what the OP was looking for?
From his first posts:
poopship21 wrote:it should be possible to use jackd to let one instance of mplayer show video with no sound while permitting the audio from the other instance to play at arbitrary volume
Also, read his second post. <shrugs>

Error Message: The attempt to connect to the report server failed. Check your connection information and that the report server is a compatible version. The request failed with HTTP status 404: Not Found.

I have a web page that contains a ReportViewer control. I am trying to display a report, which is an .rdl file located on the SSRS server, in this ReportViewer control. I have set the ReportPath and ReportServerUrl correctly. I am
getting an error message.
Am I suppose to use an .rdlc file rather than a .rdl file? Does the web server configuration need to use a certain account?
I am getting the following error message:
The attempt to connect to the report server failed. Check your connection information and that the report server is a compatible version.
The request failed with HTTP status 404: Not Found.

Hi bucaroov,
The error "The request failed with HTTP status 404: Not Found." means the ReportServerURL configured in the ReportViewer control is invalid.
Please follow these steps to solve the issue:
Logon the Report Server machine.
Open the Reporting Services Configuration Manager.
Copy the Report Server URL from 'Web Services URL'.
Logon the application server(in this case, it is the server that host the web page), check if we can use the URL we got from step 3 to access the Report Server. If so, please replace the ReportServerURL in the ReportViewer control with this URL. If it is
not available, could you please post the error message.
Additionaly, we don't need to provide the extension for a server report. The ReportPath should be like: /<reports folder>/<report name>
For more information, please see:
Walkthrough: Using the ReportViewer Control in Remote Mode:
http://msdn.microsoft.com/en-us/library/ms251669(VS.80).aspx
If you have any more questions, please feel free to ask.
Thanks,
Jin Chen
Jin Chen - MSFT

SMS_WSUS_CONFIGURATION_MANAGER - MessageID 6600 - The request failed with HTTP status 503: Service Unavailable

Hi all,
knowning that there are already a lot of posts concerning above message, I have to write an additional one as I could not find a solution on the web yet.
Situation:
Windows Server 2008 forest including empty root and two child domains, one child domain does have SCCM SP1 (central primary site WND) installed on W2k8 x64 machine including WSUS 3.0 SP1 => everything is working fine.
Second child domain also contains a SCCM SP1 server (primary site HUN) running on W2k8 x64 and is defined as child site of central site WND => everything is working fine too - except Software Updates.
WSUS 3.0 SP1 installed on both SCCM servers by creating additional web site (not using "defautl web site") and configured ports 8530 and 8531 (SSL not used!). No proxy necessary/used. All WSUS 3.0 requirements for W2k8 are installed (IIS roles)
Error:
SMS_WSUS_CONFIGURATION_MANAGER - MessageID 6600:
SMS WSUS Configuration Manager failed to configure upstream server settings on WSUS Server "xxxx0003".
Possible cause: WSUS Server version 3.0 SP1 and above is not installed or cannot be contacted.
Solution: Verify that the WSUS Server version 3.0 SP1 or greater is installed. Verify that the IIS ports configured in SMS are same as those configured on the WSUS IIS website.
wsusutil checkhealth =>OK
downloading updates from WSUS at central site (SUSDB and WSUS folder equal in size) =>OK
wsus admin console able to connect and configuration possible => OK
IIS ports configured within SMS are equal to those configured for WSUS website
SCCM config (using Configuration Manager Console) does look correct - ConfigMgr Software Update Point role properties and Software Update Point Component properties
wcm.log does report an error: (SCCM Log files at the end.)
"The request failed with HTTP status 503: Service Unavailable"
IIS log files of both websites (default web site and WSUS Administration website) do not show any errors.
Questions:
What else should I look at? (registyr, SUSDB content,..)
What exactly does happen during the attempt to configure the upstream server by the SMS_WSUS_Configuration_Manager component? I guess a SMS process tries to contact a webservice - would it be possible to debug in more detail ?
And finally - Who does know the solution ?
wcm.log:
Found WSUS Admin dll of assembly version Microsoft.UpdateServices.Administration, Version=3.0.6000.273, Major Version = 0x30000, Minor Version = 0x17700111 SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
Found WSUS Admin dll of assembly version Microsoft.UpdateServices.Administration, Version=3.1.6001.1, Major Version = 0x30001, Minor Version = 0x17710001 SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
The installed WSUS build has the valid and supported WSUS Administration DLL assembly version (3.1.6001.65) SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
System.Net.WebException: The request failed with HTTP status 503: Service Unavailable.~~ at Microsoft.UpdateServices.Administration.AdminProxy.CreateUpdateServer(Object[] args)~~ at Microsoft.UpdateServices.Administration.AdminProxy.GetUpdateServer(String serverName, Boolean useSecureConnection, Int32 portNumber)~~ at Microsoft.SystemsManagementServer.WSUS.WSUSServer.ConnectToWSUSServer(String ServerName, Boolean UseSSL, Int32 PortNumber) SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
Remote configuration failed on WSUS Server. SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
STATMSG: ID=6600 SEV=E LEV=M SOURCE="SMS Server" COMP="SMS_WSUS_CONFIGURATION_MANAGER" SYS=xxxx0003 SITE=HUN PID=2424 TID=4468 GMTDATE=Mi Jul 16 10:49:47.758 2008 ISTR0="xxxx0003" ISTR1="" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=0 SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
Waiting for changes for 59 minutes SMS_WSUS_CONFIGURATION_MANAGER 16.07.2008 12:49:47 4468 (0x1174)
wsusctrl.log (looks fine to me - is able to connect to local WSUS !):
SMS_EXECUTIVE started SMS_WSUS_CONTROL_MANAGER as thread ID 6156 (0x180C). SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 2732 (0x0AAC)
This is a WSUS Role as WSUS registry key exists. SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Found WSUS Admin dll of assembly version Microsoft.UpdateServices.Administration, Version=3.0.6000.273, Major Version = 0x30000, Minor Version = 0x17700111 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Found WSUS Admin dll of assembly version Microsoft.UpdateServices.Administration, Version=3.1.6001.1, Major Version = 0x30001, Minor Version = 0x17710001 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
The installed WSUS build has the valid and supported WSUS Administration DLL assembly version (3.1.6001.65) SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Successfully connected to local WSUS server SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Local WSUS Server Proxy settings are correctly configured as Proxy Name and Proxy Port 80 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Waiting for changes for 0 minutes SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Timed Out... SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Found WSUS Admin dll of assembly version Microsoft.UpdateServices.Administration, Version=3.0.6000.273, Major Version = 0x30000, Minor Version = 0x17700111 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Found WSUS Admin dll of assembly version Microsoft.UpdateServices.Administration, Version=3.1.6001.1, Major Version = 0x30001, Minor Version = 0x17710001 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
The installed WSUS build has the valid and supported WSUS Administration DLL assembly version (3.1.6001.65) SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Successfully connected to local WSUS server SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Local WSUS Server Proxy settings are correctly configured as Proxy Name and Proxy Port 80 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Successfully connected to local WSUS server SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
There are no unhealthy WSUS Server components on WSUS Server xxxx0003 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:01 6156 (0x180C)
Successfully checked database connection on WSUS server xxxx0003 SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:02 6156 (0x180C)
Waiting for changes for 57 minutes SMS_WSUS_CONTROL_MANAGER 16.07.2008 12:04:02 6156 (0x180C)
wsyncmgr.log (as a result of being not able to configure upstream server I guess):
STATMSG: ID=6701 SEV=I LEV=M SOURCE="SMS Server" COMP="SMS_WSUS_SYNC_MANAGER" SYS=xxxx0003 SITE=HUN PID=2424 TID=4476 GMTDATE=Mi Jul 16 10:03:51.481 2008 ISTR0="" ISTR1="" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=0 SMS_WSUS_SYNC_MANAGER 16.07.2008 12:03:51 4476 (0x117C)
Sync failed: WSUS server not configured. Source: CWSyncMgr:oSync SMS_WSUS_SYNC_MANAGER 16.07.2008 12:08:51 4476 (0x117C)
STATMSG: ID=6703 SEV=E LEV=M SOURCE="SMS Server" COMP="SMS_WSUS_SYNC_MANAGER" SYS=xxxx0003 SITE=HUN PID=2424 TID=4476 GMTDATE=Mi Jul 16 10:08:51.636 2008 ISTR0="CWSyncMgr:oSync" ISTR1="WSUS server not configured" ISTR2="" ISTR3="" ISTR4="" ISTR5="" ISTR6="" ISTR7="" ISTR8="" ISTR9="" NUMATTRS=0 SMS_WSUS_SYNC_MANAGER 16.07.2008 12:08:51 4476 (0x117C)

I just experienced the exact same scenario. After much digging I found that csakg6so posted a fix at
Windoows-Noob
Run Internet Explorer as the SYSTEM account (psexec -s -d -i cmd.exe & C:\Program Files\Internet Explorrer\iexplore.exe)
Go to internet options
Go to conections
Go to LAN settings
Uncheck all boxes
The original post said to reboot, but that wasn't necessary for me.
After initiating a manual Software Update sync the WCM.log and WSyncMgr.log errors do not return and new updates are synchronized.

Problems connecting to SSRS using IReportServerCredentials, the request failed with http status 401: unauthorized

We have a hosted SSRS server and we access it's reports using the reportviewer in an ASP.net application.
We are getting the error: The request failed with HTTP status 401: Unauthorized. When trying to run one of the reports. I have confirmed that the login details work when logging into the report manager page directly.
I have implemented an instance of IReportServerCredentials in a separate class (below) and I call it from the page before it tries to access the report. I'm not sure if this is all I need but can't seem to find any other info.
I have managed to gain access connecting to the external server from my PC and accessed the report, but when I promote the code to production and run it from there on my local PC I get the unauthorized message again: the request failed with http status
401: unauthorized
The class:
[Serializable]
public sealed class MyReportServerCredentials :
IReportServerCredentials
public WindowsIdentity ImpersonationUser
get
// Use the default Windows user. Credentials will be
// provided by the NetworkCredentials property.
return null;
public ICredentials NetworkCredentials
get
// Read the user information from the Web.config file.
// By reading the information on demand instead of
// storing it, the credentials will not be stored in
// session, reducing the vulnerable surface area to the
// Web.config file, which can be secured with an ACL.
// User name
string userName =
ConfigurationManager.AppSettings
["MyReportViewerUser"];
if (string.IsNullOrEmpty(userName))
throw new Exception(
"Missing user name from web.config file");
// Password
string password =
ConfigurationManager.AppSettings
["MyReportViewerPassword"];
if (string.IsNullOrEmpty(password))
throw new Exception(
"Missing password from web.config file");
// Domain
string domain =
ConfigurationManager.AppSettings
["MyReportViewerDomain"];
return new NetworkCredential(userName, password);
public bool GetFormsCredentials(out Cookie authCookie,
out string userName, out string password,
out string authority)
authCookie = null;
userName = null;
password = null;
authority = null;
// Not using form credentials
return false;
The call to the class, just before the report is run:
if (GetConnection.GetConnectionString().ToString().Contains("IP of external server removed"))
invoiceviewer.ServerReport.ReportServerCredentials = new MyReportServerCredentials();
We have tried so many things here, we don't even care whether the server authenticates or not but it appears to be as standard. Our hosting company has also drawn a blank and changed so many settings to no ava

Hi Nasa1999,
According to your description, you are getting the error: The request failed with HTTP status 401: Unauthorized when you access the report using the ReportViewer in an ASP.net application.
Regarding the 401 error, it could cause by the Service Principal Name(SPN) for the account the Reporting Services is running under hasn’t been registered when the Reporting Services is configured to use Kerberos authentication. So in your scenario,
please check if you are using Kerberos authentication. If that is a case, please make sure SPN is configured correctly. For more information, please refer to the similar thread:
The request failed with HTTP status 401: Unauthorized. in SSRS.
If issue persists, please check the Reporting Service error log (default location: %programfiles%\Microsoft SQL Server\<SQL Server Instance>\Reporting Services\LogFiles) around the time that the error message thrown out.
If you have any question, please feel free to ask.
Best regards,
Qiuyun Yu
Qiuyun Yu
TechNet Community Support

"The request failed with HTTP status 401: Unauthorized"

Hi,
I'm trying to get both RSS feeds and SSRS reports on a web application which is having NTLM authentication without Kerberos. The catch is proxy setting, if I give <proxy autoDetect="false" /> in web.config of my sharepoint web
application SSRS reports will be rendered in SQL Server Report viewer perfectly (I deploy using BIDS), but RSS viewer webpart will not display my internet feeds. If I give
<proxy autoDetect="true" /> RSS feeds are displayed properly but SSRS report will throw the following error.
The request failed with HTTP status 401: Unauthorized.
Description:
An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Net.WebException: The request failed with HTTP status 401: Unauthorized.
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[WebException: The request failed with HTTP status 401: Unauthorized.]
System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +412862
System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +300
Microsoft.SqlServer.ReportingServices2005.Execution.ReportExecutionService.ListRenderingExtensions() +53
Microsoft.SqlServer.ReportingServices2005.Execution.RSExecutionConnection.ListRenderingExtensions() +207
Microsoft.Reporting.WebForms.ServerReport.ListRenderingExtensions() +130
Microsoft.ReportingServices.SharePoint.UI.WebParts.ActionMenu.OnPreRender(EventArgs e) +180
System.Web.UI.Control.PreRenderRecursiveInternal() +108
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Control.PreRenderRecursiveInternal() +224
System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) +3394
I tried to work around this by adding proxy settings with bypass list.
<system.net>
    <defaultProxy useDefaultCredentials="true">
      <proxy proxyaddress="http://<proxy IP address>:<port>" bypassonlocal="true" usesystemdefault="true" />
      <bypasslist>
  <add address="<my report server>" />
  <add address="http://<report server>:8080/reportserver/" />
  <add address="<IP of my report server>" />
      </bypasslist>
    </defaultProxy>
</system.net>
This makes RSS feed to work but SSRS throw the above error. I would need some advice from Microsoft on how to fix this.
Note: My sharepoint site cannot be anonymous. I have just once service account that runs sql server service, report service, sharepoint services etc. This account is local admin on all servers, has highest access on sql box, run SSRS web service and app
pools, etc.
I have four servers, 2 WFE in windows load balanced, 1 app server (running Central admin and report service in sharepoint integrated mode), 1 db server hosting all content and config dbs and report server db.
Regards,
Manoj
Version Information: Microsoft .NET Framework Version:2.0.50727.3615; ASP.NET Version:2.0.50727.3618

Hi,
Thanks to share your post.
For the issue,
do you mean that the error happen with the use of NTLM authentication without Kerberos? If yes, the possible cause should be the lacking of Kerberos.
My suggestion is to implement the Kerberos authentication in your environment. You may check it and test it. For the detailed steps of implementing of the Kerberos:
http://blogs.msdn.com/b/martinkearn/archive/2007/04/23/configuring-kerberos-for-sharepoint-2007-part-1-base-configuration-for-sharepoint.aspx.
http://blogs.msdn.com/b/james_world/archive/2007/08/20/essential-guide-to-kerberos-in-sharepoint.aspx.
Hope this could help you!
Leo

The request failed with HTTP status 404: Not Found

Hi
BPC version we are using is : 5.0.502
When we Publish all reports using the steps below:
a. Log into BPC Web
b. Click on Available Interfaces> Select BPC for Administration
c. Under Web Admin Task Click Publish Reports
d. Select all of the reports and click the green check mark to publish the
reports.
I am getting following message 'System.Exception: The request failed with HTTP Status 404: Not Found. Event log relation to this error is given below.
Event Type:     Error
Event Source:     OutlookSoft log
Event Category:     None
Event ID:     0
Date:          12/8/2008
Time:          11:26:42 AM
User:          N/A
Computer:     BPCAPP
Description:
==============[System Error Tracing]==============
[System Name] : OSoftCPM
[Message Type] : ErrorMessage
[Job Name]     : AuditMgrService/SetAuditReportFiles
[DateTime]     : 12/8/2008 11:26:42 AM
[UserId]       : MMPlanning
[Exception]
    DetailMsg : {The request failed with HTTP status 404: Not Found.}
==============[System Error Tracing End ]==============
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.
We tried ' Publish all reports' as the resolution of error 'object variable or with block variable not set' on modifying an application as per sap note Note 1131320
If anyone knows the resolution for the above issue, please help me.
Thanks in advance
Sajeev Abraham

Hi
Thanks for the response.
Below are the full contents of the error message pop-up.
( System.Expection: the reguest failed with HTTP status 404:Not found at
Microsoft.Visualbasic.CompierServices.lateBinding.LateGet(Object o, Type,String name, Object
[]args,sTRING[]paramnames, Boolen[]CopyBack)
at OSoft.Services.WebServices.ReportmanageProxy.ReportManageProxy.SetPubishReport(String strAppSet,string
strApp,string strFiter)
url is given below
http://<HostName>/osoft/Admin/WebAdminMain.aspx
BPC Deployment is Multiple server ( Two servers) Database and Application deployed seperately.
Sql Reporting server is working.. I could connect using sql management studio.
Thanks

'System.Exception: The request failed with HTTP Status 404

Hi
BPC version we are using is : 5.0.502
When we Publish all reports using the steps below:
a. Log into BPC Web
b. Click on Available Interfaces> Select BPC for Administration
c. Under Web Admin Task Click Publish Reports
d. Select all of the reports and click the green check mark to publish the
reports.
I am getting following message 'System.Exception: The request failed with HTTP Status 404: Not Found. Below are the event log relation to this error.
Event Type:     Error
Event Source:     OutlookSoft log
Event Category:     None
Event ID:     0
Date:          12/8/2008
Time:          11:26:42 AM
User:          N/A
Computer:     BPCAPP
Description:
==============[System Error Tracing]==============
[System Name] : OSoftCPM
[Message Type] : ErrorMessage
[Job Name]     : AuditMgrService/SetAuditReportFiles
[DateTime]     : 12/8/2008 11:26:42 AM
[UserId]       : MMPlanning
[Exception]
    DetailMsg : {The request failed with HTTP status 404: Not Found.}
==============[System Error Tracing End ]==============
We tried ' Publish all reports' as the resolution of error 'object variable or with block variable not set' on modifying an application as per sap note Note 1131320
If anyone knows the resolution for the above issue, please help me.
Thanks in advance
Sajeev Abraham

Hi,
This forum is for BI Integrated planning an BW/SEM BPS. For BPC related questions please post this message in the forum for Enterprise Performance Management (Enterprise Performance Management (SAP EPM)).
Best regards,
Gerd Schoeffl,
SAP NetWeaver RIG BI

Error: on clicking Registry menu item in ESM Management Portal. The request failed with HTTP status 404: Not Found.

Hi,
I have installed ESB Management Portal successfully after following all the steps. everything is working fine except when I click the Registry menu in the portal. I get an unhandled exception. The event viewer shows the below error "The request failed
with HTTP status 404: Not Found."
================================================
Event code: 3005
Event message: An unhandled exception has occurred.
Event time: 1/27/2015 5:56:10 PM
Event time (UTC): 1/27/2015 5:56:10 PM
Event ID: f7aedd39118845b79c17d3442a0d15a7
Event sequence: 54
Event occurrence: 1
Event detail code: 0
Application information:
Application domain: /LM/W3SVC/1/ROOT/ESB.Portal-1-130668549484455107
Trust level: Full
Application Virtual Path: /ESB.Portal
Application Path: C:\Projects\Microsoft.Practices.ESB\Source\Samples\Management Portal\ESB.Portal\
Machine name: <Machine Name>
Process information:
Process ID: 4712
Process name: w3wp.exe
Account name: NT AUTHORITY\NETWORK SERVICE
Exception information:
Exception type: TargetInvocationException
Exception message: Exception has been thrown by the target of an invocation.
at System.RuntimeMethodHandle.InvokeMethod(Object target, Object[] arguments, Signature sig, Boolean constructor)
at System.Reflection.RuntimeMethodInfo.UnsafeInvokeInternal(Object obj, Object[] parameters, Object[] arguments)
at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture)
at System.Web.UI.WebControls.ObjectDataSourceView.InvokeMethod(ObjectDataSourceMethod method, Boolean disposeInstance, Object& instance)
at System.Web.UI.WebControls.ObjectDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments)
at System.Web.UI.DataSourceView.Select(DataSourceSelectArguments arguments, DataSourceViewSelectCallback callback)
at System.Web.UI.WebControls.DataBoundControl.PerformSelect()
at System.Web.UI.WebControls.BaseDataBoundControl.EnsureDataBound()
at System.Web.UI.WebControls.CompositeDataBoundControl.CreateChildControls()
at System.Web.UI.Control.EnsureChildControls()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
The request failed with HTTP status 404: Not Found.
at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall)
at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters)
at Microsoft.Practices.ESB.Portal.UDDIService.UDDIService.GetCategoryByName(String UDDIServerUrl, String tModelName) in c:\Projects\Microsoft.Practices.ESB\Source\Samples\Management Portal\ESB.Portal\Web References\UDDIService\Reference.cs:line
575
at Microsoft.Practices.ESB.Portal.Uddi.ServiceProxy.getBTEndpoints(String applicationName, Boolean getSendPorts, Boolean getRcvLocations) in c:\Projects\Microsoft.Practices.ESB\Source\Samples\Management Portal\ESB.Portal\Uddi\ServiceProxy.cs:line
553
at Microsoft.Practices.ESB.Portal.Uddi.ServiceProxy.GetEndpointsByApplication(String applicationName, Boolean getSendPorts, Boolean getRcvLocations) in c:\Projects\Microsoft.Practices.ESB\Source\Samples\Management Portal\ESB.Portal\Uddi\ServiceProxy.cs:line
46
Request information:
Request URL: http://localhost/ESB.Portal/uddi/uddi.aspx
Request path: /ESB.Portal/uddi/uddi.aspx
User host address: ::1
User: <domain>\<user>
Is authenticated: True
Authentication Type: Negotiate
Thread account name: NT AUTHORITY\NETWORK SERVICE
Thread information:
Thread ID: 19
Thread account name: NT AUTHORITY\NETWORK SERVICE
Is impersonating: False
Stack trace: at System.RuntimeMethodHandle.InvokeMethod(Object target, Object[] arguments, Signature sig, Boolean constructor)
at System.Reflection.RuntimeMethodInfo.UnsafeInvokeInternal(Object obj, Object[] parameters, Object[] arguments)
at System.Reflection.RuntimeMethodInfo.Invoke(Object obj, BindingFlags invokeAttr, Binder binder, Object[] parameters, CultureInfo culture)
at System.Web.UI.WebControls.ObjectDataSourceView.InvokeMethod(ObjectDataSourceMethod method, Boolean disposeInstance, Object& instance)
at System.Web.UI.WebControls.ObjectDataSourceView.ExecuteSelect(DataSourceSelectArguments arguments)
at System.Web.UI.DataSourceView.Select(DataSourceSelectArguments arguments, DataSourceViewSelectCallback callback)
at System.Web.UI.WebControls.DataBoundControl.PerformSelect()
at System.Web.UI.WebControls.BaseDataBoundControl.EnsureDataBound()
at System.Web.UI.WebControls.CompositeDataBoundControl.CreateChildControls()
at System.Web.UI.Control.EnsureChildControls()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Control.PreRenderRecursiveInternal()
at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
Custom event details:
=================================
Any idea why this is happening and what needs to be done ?
PLEASE HELP
Thanks & Regards
Vikram

Snippet from the link below:
If you get a “404: Not Found” error, it ‘s because by default there is no script map for .svc file with default IIS 7.0 installation, so you need to register .svc extension in IIS:
You need to update IIS script maps to register .svc extension In a command prompt (ran as administrator), execute the following command:
“%windir%\Microsoft.NET\Framework\v3.0\Windows Communication Foundation\ServiceModelReg.exe” -r -y"
Refer:
https://dgoins.wordpress.com/2010/05/01/esb-toolkit-management-portal-installation-notes-from-the-field-2/
Sarvanan's blog around this with detailed explanation:
Configuring Exception Management Portal
As mentioned above also
Check Portal Configuration Settings
Rachit
Please mark as answer or vote as helpful if my reply does

"The request failed with HTTP Status 400: Bad Request." when running reports

Hi,
I installed reporting services and the install went fine.  The Reporting Services are located on a different server. I can see all the reports in SCCM but when I try to run them I get the "400" error with the following details:
System.Net.WebException
The request failed with HTTP status 400: Bad Request.
Stack Trace:
   at System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall)
   at System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters)
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.ReportExecutionService.LoadReport2(String Report, String HistoryID)
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.<>c__DisplayClass2.<LoadReport>b__0()
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.ProxyMethodInvocation.Execute[TReturn](RSExecutionConnection connection, ProxyMethod`1 initialMethod, ProxyMethod`1 retryMethod)
   at Microsoft.Reporting.WinForms.Internal.Soap.ReportingServices2005.Execution.RSExecutionConnection.LoadReport(String Report, String HistoryID)
   at Microsoft.Reporting.WinForms.ServerReport.EnsureExecutionSession()
   at Microsoft.Reporting.WinForms.ServerReport.SetParameters(IEnumerable`1 parameters)
   at Microsoft.ConfigurationManagement.AdminConsole.SrsReporting.ReportViewerWindowsForms.SetParameterValues_DoWork(Object sender, DoWorkEventArgs e)
I can open the URL from the SCCM server but when I select a report I am unable to select any report options if available. If no options are availble the report just doesn't run, I don't get and error if I select "View Report" mutiple
times.
If I connect to the Reporting Services site on the computer where it is installed all the reports run fine.
One thing I have noticed is that when I try to change or add a role assignment for Reporting Services the edited account always reverts back to the default settings and the added Domain user is dropped.
Thanks

I reviewed the topic and found a couple of steps I missed the first time around. I had to "Configure Reports to Use Report Builder 3.0 and setting the "Log on Locally" permission.
I then uninstalled the role and reinstalled it. I am still getting the 400 error.
When I inspected the SmsAdminUI.log I noticed the Error on the last line 2151811598 (it repeats in the log). I couldn't find anything specific related to it. By reading a few "related" Internet posts I came accross a intial setup
blog that noted some WMI firewall execptions (Async-in, DCOM-in and WMI-in) as require so I checked and they were not allowed on the SCCM server so I allowed them and tested with the same result. I turned them off again.
Here is the tail end of the SmsAdminUI.log
[19, PID:2684][01/24/2013 16:08:29] :[ReportProxy] - User-specified default Reporting Point [INC-SQL42.deccoinc.net] could not be found, [] is now the default Reporting Point.
[4, PID:2684][01/24/2013 16:08:30] :[ReportProxy] - User-specified default Reporting Point [INC-SQL42.deccoinc.net] could not be found, [] is now the default Reporting Point.
[15, PID:2684][01/24/2013 16:08:30] :[ReportProxy] - User-specified default Reporting Point [INC-SQL42.deccoinc.net] could not be found, [] is now the default Reporting Point.
[1, PID:2684][01/24/2013 19:06:02] :System.Management.ManagementException\r\nNot found \r\n   at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
   at System.Management.ManagementObject.Initialize(Boolean getObject)
   at System.Management.ManagementBaseObject.get_wbemObject()
   at System.Management.PropertyData.RefreshPropertyInfo()
   at System.Management.PropertyDataCollection.get_Item(String propertyName)
   at System.Management.ManagementBaseObject.GetPropertyValue(String propertyName)
   at System.Management.ManagementBaseObject.get_Item(String propertyName)
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.GetInstance(String objectPath)\r\nManagementException details:
instance of SMS_ExtendedStatus
Description = "Error retrieving object FileType=2";
ErrorCode = 2151811598;
File = "e:\\nts_sccm_release\\sms\\siteserver\\sdk_provider\\smsprov\\SspInterface.h";
Line = 1208;
Operation = "GetObject";
ParameterInfo = "SMS_SCI_SysResUse.FileType=2,ItemName=\"[\\\"Display=\\\\\\\\INC-SQL42.deccoinc.net\\\\\\\"]MSWNET:[\\\"SMS_SITE=INC\\\"]\\\\\\\\INC-SQL42.deccoinc.net\\\\,SMS SRS Reporting Point\",ItemType=\"System Resource Usage\",SiteCode=\"INC\"";
ProviderName = "ExtnProv";
StatusCode = 2147749890;
\r\n
[1, PID:2684][01/24/2013 23:39:14] :System.NullReferenceException\r\nObject reference not set to an instance of an object.\r\n   at Microsoft.ConfigurationManagement.AdminConsole.SmsCustomDialog.get_LocaleIndependentIdentifier()
   at Microsoft.ConfigurationManagement.AdminConsole.ShowDialogTaskHandler.DoTask(NavigationModelNodeBase node, SccmTaskConfiguration sccmTask, PropertyDataUpdated dataUpdatedDelegate, Boolean readOnly)\r\n
[1, PID:5008][01/25/2013 20:48:00] :System.Management.ManagementException\r\nNot found \r\n   at System.Management.ManagementException.ThrowWithExtendedInfo(ManagementStatus errorCode)
   at System.Management.ManagementObject.Initialize(Boolean getObject)
   at System.Management.ManagementBaseObject.get_wbemObject()
   at System.Management.PropertyData.RefreshPropertyInfo()
   at System.Management.PropertyDataCollection.get_Item(String propertyName)
   at System.Management.ManagementBaseObject.GetPropertyValue(String propertyName)
   at System.Management.ManagementBaseObject.get_Item(String propertyName)
   at Microsoft.ConfigurationManagement.ManagementProvider.WqlQueryEngine.WqlConnectionManager.GetInstance(String objectPath)\r\nManagementException details:
instance of SMS_ExtendedStatus
Description = "Error retrieving object FileType=2";
ErrorCode = 2151811598;
File = "e:\\nts_sccm_release\\sms\\siteserver\\sdk_provider\\smsprov\\SspInterface.h";
Line = 1208;
Operation = "GetObject";
ParameterInfo = "SMS_SCI_SysResUse.FileType=2,ItemName=\"[\\\"Display=\\\\\\\\INC-SQL42.deccoinc.net\\\\\\\"]MSWNET:[\\\"SMS_SITE=INC\\\"]\\\\\\\\INC-SQL42.deccoinc.net\\\\,SMS SRS Reporting Point\",ItemType=\"System Resource Usage\",SiteCode=\"INC\"";
ProviderName = "ExtnProv";
StatusCode = 2147749890;
\r\n

Replace AR Credit Memo Request Workflow with a new Custom Workflow

Hello friends,
We have a business requirement to replace the AR Credit Memo Request Workflow with a new Custom Workflow whenever an Invoice is disputed (Oracle Advanced Collections).
The Credit Memo Request workflow is being launched within the Oracle API arw_cmreq_cover. We thought of an approach wherein the Oracle form IEXINDTL.fmb can be renamed and the Custom workflow to be called in the WHEN-BUTTON-PRESSED trigger on Dispute Button instead of calling the program Unit IEXINDTL_CONTROL.DISPUTE (as in standard form) which inturn calls several API's and hence the AR Credit Memo Request Workflow. But this would override the other standard processes being carried out in these API's. Our requirement is to only replace the AR Credit Memo Request Workflow and not to override the other standard processes.
Does anyone have come across the similar requirement? Please let us know your inputs.
Thanks in Advance !

I ran across the same error today. Since it's been over a month, I assume you've fixed it already or decided you didn't need it at all? What was your fix?
For me, I noted that in the sample directory, a similar "createView" call (in End User Anonymous Enrollment) also includes this argument:
<Argument name='viewId' value='User'/>
When I added that to my createView call, the "Missing view id" error went away, and the user are gets created.
I'm not entirely comfortable with the value specified, though; seems like view IDs should be more unique. I would have thought it should have been something like this instead:
<Argument name='viewId' value='User:$(accountId)'/>

Issue about BI JAVA SDK-SOAP request failed with return message 2147483653

Dear Experts,
I'm trying to use BI JAVA SDK to connect BW by using XMLA connector.
But there's an error messaet said :
SOAP request failed with return message 2147483653 ( Invalid MDX command with INCLUDING)
I'm really new to this JAVA SDK, and after searching help in SAP Service Market and Google, there's no helpful suggestion.
please help me about how to fix this error.
Here is my code:
IBIConnection connection = (IBIConnection) cf.getConnectionEx(cs);
      IBIOlap olap = connection.getOlap();
      Cube cube = olap.getObjectFinder().
      findCubeFirst((String)null, "ZFI_C11/ZFI_C11_Q001");
    // This is just a sanity check to verify that the
    // cube on which this example relies was retrieved
    if (cube==null){
        System.out.println("no cube found");
// Didn't print out this message, seems it can connect to BW and get the InfoCube and Query.
    Dimension plantDimension = olap.getObjectFinder().
    findDimensionFirst(cube, "ZPLANT");
Dimension materialDimension = olap.getObjectFinder().
    findDimensionFirst(cube, "ZMATERIAL");
IBIQuery query = olap.createQuery(cube);
IBICommandProcessor commandProcessor = query.getCommandProcessor();
commandProcessor.moveDimensionToRows(plantDimension);
commandProcessor.moveDimensionToRows(materialDimension);
IBIDataSet dataset = query.execute(); // After execute this statement, error happens.
Thank you!
Andy

Solved myself, it's because the query used in my code have user input variable.

Servlet request terminated with IOException:java.io.IOException: There is no process to read data written to a pipe.

Hi,
I am getting this following error. Could anyone please throw some light.
Thanks
Nilesh
<HTTP> Servlet request terminated with IOException:
java.io.IOException: There is no process to read data written to a pipe.
     at java.net.SocketOutputStream.socketWrite(Native Method)
     at java.net.SocketOutputStream.write(SocketOutputStream.java(Compiled Code))
     at weblogic.servlet.internal.ChunkUtils.writeChunks(ChunkUtils.java(Compiled
Code))
     at weblogic.servlet.internal.ResponseHeaders.writeHeaders(ResponseHeaders.java(Compiled
Code))
     at weblogic.servlet.internal.ServletResponseImpl.writeHeaders(ServletResponseImpl.java(Compiled
Code))
     at weblogic.servlet.internal.ServletOutputStreamImpl.flush(ServletOutputStreamImpl.java(Compiled
Code))
     at weblogic.servlet.internal.ServletOutputStreamImpl.finish(ServletOutputStreamImpl.java(Compiled
Code))
     at weblogic.servlet.internal.ServletContextManager.invokeServlet(ServletContextManager.java(Compiled
Code))
     at weblogic.socket.MuxableSocketHTTP.invokeServlet(MuxableSocketHTTP.java(Compiled
Code))
     at weblogic.socket.MuxableSocketHTTP.execute(MuxableSocketHTTP.java(Compiled
Code))
     at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:129)

I forgot to mention.
I am using Weblogic 5.1 with SP 9
Nilesh
"Nilesh Shah" <[email protected]> wrote:
>
Hi,
I am getting this following error. Could anyone please throw some light.
Thanks
Nilesh
<HTTP> Servlet request terminated with IOException:
java.io.IOException: There is no process to read data written to a pipe.
     at java.net.SocketOutputStream.socketWrite(Native Method)
     at java.net.SocketOutputStream.write(SocketOutputStream.java(Compiled
Code))
     at weblogic.servlet.internal.ChunkUtils.writeChunks(ChunkUtils.java(Compiled
Code))
     at weblogic.servlet.internal.ResponseHeaders.writeHeaders(ResponseHeaders.java(Compiled
Code))
     at weblogic.servlet.internal.ServletResponseImpl.writeHeaders(ServletResponseImpl.java(Compiled
Code))
     at weblogic.servlet.internal.ServletOutputStreamImpl.flush(ServletOutputStreamImpl.java(Compiled
Code))
     at weblogic.servlet.internal.ServletOutputStreamImpl.finish(ServletOutputStreamImpl.java(Compiled
Code))
     at weblogic.servlet.internal.ServletContextManager.invokeServlet(ServletContextManager.java(Compiled
Code))
     at weblogic.socket.MuxableSocketHTTP.invokeServlet(MuxableSocketHTTP.java(Compiled
Code))
     at weblogic.socket.MuxableSocketHTTP.execute(MuxableSocketHTTP.java(Compiled
Code))
     at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:129)

[REQUEST] mplayer with eac3

Similar Messages

Maybe you are looking for