Request Timed Out when server is plugged in!
jonathanmendez wrote:
1 - Error - DNS-Server-Service 404
The DNS server could not bind a transmission Control Protocol (TCP) scoket to address 10.10.10.3. The event data is the error code. An IP address of 0.0.0.0 can indicate a valid "any address" configuration in which all configured IP addresses on the computer are available for use. Restart the DNS server or reboot the computer.
Does the DNS Service stop?
Can you confirm that no other application is listening on port 53?
Also, what is handling DHCP?
So I am facing the weirdest network/server problem ever!I have a customer which had a Supermicro server (Was there before me!). It was never used and they didn't know the password so i decided to format and re-install Windows Server 2012 R2 on it. I promoted it to a new domain and setup Windows Essentials so I could setup RDWeb for them quickly. They were up and running great. I also installed Trend Micro on the server and pushed it out to the client PC's. A little more info about my network before i get into the gritty. I have Brighthouse cable 35Mbps as an ISP with an ARRIS modem, a Ubiquiti Edgerouter Lite as my firewall and a cisco sg200-26 as my core switch. It's not a big location. We randomly started getting request timed out at the gateway level and the firewall level from outside and internet was dropping. We worked for weeks...
This topic first appeared in the Spiceworks Community
Similar Messages
-
I want to troubleshoot what causing the connection unstable between workstation and server. When i try do the ping test, the reply sometime 'Request timed out' Any idea what likely the cause of this issue?
I tried change network adapter, change network cable, change network port, reassign different ip address to the server. Still the result remain. I got another server on the same rack and same ip segment(base), but the other server is ok.
Any idea on this guys?
Thanks.Hi S.Akmal,
The request timed out also can caused by the remote computer no replayed, you can try to check the remote server whether it have some network issue, you also can connect this
server to another server directly(just connect them with cable) then try the ping then can determine whether issue occur on this server.
More information:
Internet Control Message Protocol (ICMP) Basics
https://support.microsoft.com/en-us/kb/170292
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Request timed out when purchasing music. Fresh install of Win7.
For the past couple months I have have not been able to purchase music off iTunes without first going into Add/Remove programs and doing a "Repair" to iTunes. Windows Firewall wasn't blocking anything from Apple and even with the firewall totally disabled I would still get the "Request timed out" error. And at the same time I'm getting these errors, a Podcast can be in the background downloading or I can be previewing a song! I eventually gave up and just figured its some random windows bug that isn't very common or its just another example of iTunes sucking for Windows and Apple not caring. I just purchased most of my music off AmazonMP3 which I've been doing more and more of anyway.
Yesterday I installed a new HDD and installed a fresh copy of Windows 7 Home Premium from my retail disc. I Installed all the updates then proceeded to install my software and put all my media back in-place. I'm a backup neat-freak so all this happen pretty easily and fast. I purchased a song off iTunes and was pleased to see it working again. Well here I am again suddenly having the issue with the connection timing out when purchasing a song. Firewall is configured fine and again I even disabled it. I know its not Windows now as there haven't been any new Drivers or Updates installed since I last purchased a song. I even tried different network adapters! What the heck is going on?This error is specific to RAS. The default CORBA request timeout is 10 minute = 600000 ms. When the RAS SDK does not get the reponse back from RAS server in 600000 ms it throws this message. Why it works in InfoView\CMC what I believe you refer to as "Front End' application is because InfoView\ CMC don't use RAS.
1. First make sure that a smaller report wich runs pretty fast ( 1-2 min) works. This will confirm that there is no connectivitiy issues between RAS and RAS SDK.
2. If you get the efrror for every single report, even the smaller ones, make sure the box running RAS and RAS SDK code( in case they are 2 different) can ping each other with IP, shortname and FQDN. If there is a firewall between them, the RAS port needs to be opened for bidirectional communication. By default RAS chooses a random port for communication with SDK but within CMC you can configure it to use a specific port and open it.
3. If the issue is specific only to reports that are long running, typically more than 10 minutes, then you need to inclease the CORBA timeout to a value more than what the reports typically would take to process. This is done on client code side or IIS in this case.
Here are the steps:
Make the following changes on the application server/system.
Open RegEdit by going to Start > Run and typing in regedit.exe. Then click Ok.
Navigate to HKEY_LOCAL_MACHINE\SOFTWARE\Business Objects\Suite 11.5\Report Application Server\Client SDK\CorbaAdapter
Change the value of SendRequestTimeout(ms) to 100000.
Change the value of WaitReplyTimeout(ms) to 6,000,000 ms. The default value is 600,000 ms and may not be long enough.
Restart IIS by going to Start > Run and typing in iisreset. Then click Ok.
Retry the failing application.
See note: 1296656
This error should be easy to fix
Edited by: Aasavari Bhave on Feb 2, 2012 11:20 AM -
Connection timed out, when server is present in far-off place
We have a web application on JBoss-3.2.3. It makes use of Applets. To paint the applet, a request is sent to a server using a HttpURLConnection. Evertyhing works fine when the browser(client) and the server are on the same network. However, if the client(browser) is in Australia and the server in India(i.e. long distance between server and client), then the Applet crashes with a Connection timed out exception. Any solution for this?
The code looks something like:
URL url = new URL(urlString);
HttpURLConnection connection = (HttpURLConnection) url.openConnection();
connection.setDoOutput(true);
connection.connect();So I am facing the weirdest network/server problem ever!I have a customer which had a Supermicro server (Was there before me!). It was never used and they didn't know the password so i decided to format and re-install Windows Server 2012 R2 on it. I promoted it to a new domain and setup Windows Essentials so I could setup RDWeb for them quickly. They were up and running great. I also installed Trend Micro on the server and pushed it out to the client PC's. A little more info about my network before i get into the gritty. I have Brighthouse cable 35Mbps as an ISP with an ARRIS modem, a Ubiquiti Edgerouter Lite as my firewall and a cisco sg200-26 as my core switch. It's not a big location. We randomly started getting request timed out at the gateway level and the firewall level from outside and internet was dropping. We worked for weeks...
This topic first appeared in the Spiceworks Community -
VPN client get connect but Request Timed out when ping
Hi, I'm using the cisco 837 router as my VPN server. I get connected using Cisco VPN Client Version 5. But when I ping the router ip, i get request timed out. Here is my configuration :
Building configuration...
Current configuration : 3704 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname michael
boot-start-marker
boot-end-marker
memory-size iomem 5
no logging console
enable secret 5 $1$pZLW$9RZ8afI8QdGRq0ssaEJVu0
aaa new-model
aaa authentication login default local
aaa authentication login sdm_vpn_xauth_ml_1 local
aaa authorization exec default local
aaa authorization network sdm_vpn_group_ml_1 local
aaa session-id common
resource policy
ip subnet-zero
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.1
ip dhcp pool michael
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 202.134.0.155
ip dhcp pool excluded-address
host 192.168.1.4 255.255.255.0
hardware-address 01c8.d719.957a.b9
ip cef
ip name-server 202.134.0.155
ip name-server 203.130.193.74
vpdn enable
username michael privilege 15 secret 5 $1$ZJQu$KDigCvYWKkzuzdYHBEY7f.
username danny privilege 10 secret 5 $1$BDs.$Ez0u9wY7ywiBzVd1ECX0N/
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp xauth timeout 15
crypto isakmp client configuration group michaelvpn
key vpnpassword
pool SDM_POOL_1
acl 199
netmask 255.255.255.0
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SDM_DYNMAP_1 1
set transform-set ESP-3DES-SHA
crypto map SDM_CMAP_1 client authentication list sdm_vpn_xauth_ml_1
crypto map SDM_CMAP_1 isakmp authorization list sdm_vpn_group_ml_1
crypto map SDM_CMAP_1 client configuration address respond
crypto map SDM_CMAP_1 65535 ipsec-isakmp dynamic SDM_DYNMAP_1
interface Ethernet0
description $FW_INSIDE$
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip tcp adjust-mss 1452
hold-queue 100 out
interface Ethernet2
no ip address
shutdown
hold-queue 100 out
interface ATM0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/35
pppoe-client dial-pool-number 1
interface FastEthernet1
duplex auto
speed auto
interface FastEthernet2
duplex auto
speed auto
interface FastEthernet3
duplex auto
speed auto
interface FastEthernet4
duplex auto
speed auto
interface Virtual-PPP1
no ip address
interface Dialer1
description $FW_OUTSIDE$
mtu 1492
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp chap hostname ispusername
ppp chap password 0 isppassword
ppp pap sent-username ispusername password 0 isppassword
crypto map SDM_CMAP_1
ip local pool SDM_POOL_1 192.168.2.1 192.168.2.5
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
no ip http secure-server
ip nat inside source static udp 192.168.1.0 1723 interface Dialer1 1723
ip nat inside source static tcp 192.168.1.4 21 interface Dialer1 21
ip nat inside source route-map SDM_RMAP_1 interface Dialer1 overload
access-list 1 remark SDM_ACL Category=16
access-list 1 permit 192.0.0.0 0.255.255.255
access-list 102 remark SDM_ACL Category=2
access-list 102 deny ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 102 permit ip 192.168.1.0 0.0.0.255 any
access-list 199 permit ip 192.168.1.0 0.0.0.255 192.168.2.0 0.0.0.255
route-map SDM_RMAP_1 permit 1
match ip address 102
control-plane
banner motd ^C
Authorized Access Only
UNAUTHORIZED ACCESS TO THIS DEVICE IS PROHIBITED
You must have explicit permission to access this device.
All activities performed on this device are logged.
Any violations of access policy will result in disciplinary action.
^C
line con 0
no modem enable
line aux 0
line vty 0 4
scheduler max-task-time 5000
end
Thank you, anny help will be appreciated.Thank you for your response, here is the debug :
Log Buffer (4096 bytes):
1 15:19:47.011: ISAKMP: set new node 856647599 to QM_IDLE
May 1 15:19:47.015: ISAKMP:(0:8:SW:1):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
spi 2182802952, message ID = 856647599
May 1 15:19:47.015: ISAKMP:(0:8:SW:1): seq. no 0xA3285B8A
May 1 15:19:47.015: ISAKMP:(0:8:SW:1): sending packet to 120.168.1.24 my_port 4500 peer_port 52667 (R) QM_IDLE
May 1 15:19:47.019: ISAKMP:(0:8:SW:1):purging node 856647599
May 1 15:19:47.019: ISAKMP:(0:8:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
May 1 15:19:47.019: ISAKMP:(0:8:SW:1):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
May 1 15:19:49.979: %SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr=81B4F274, count=0
-Traceback= 0x80137488 0x801DC350 0x801DDDA8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:19:49.983: %SYS-2-BADSHARE: Bad refcount in datagram_done, ptr=81B4F274, count=0
-Traceback= 0x80137488 0x801D8830 0x801DDFD8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:19:55.127: %SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr=81B51C44, count=0
-Traceback= 0x80137488 0x801DC350 0x801DDDA8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:19:55.127: %SYS-2-BADSHARE: Bad refcount in datagram_done, ptr=81B51C44, count=0
-Traceback= 0x80137488 0x801D8830 0x801DDFD8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:19:58.383: ISAKMP (0:134217736): received packet from 120.168.1.24 dport 4500 sport 52667 Global (R) QM_IDLE
May 1 15:19:58.383: ISAKMP: set new node -1340288848 to QM_IDLE
May 1 15:19:58.387: ISAKMP:(0:8:SW:1): processing HASH payload. message ID = -1340288848
May 1 15:19:58.387: ISAKMP:(0:8:SW:1): processing NOTIFY DPD/R_U_THERE protocol 1
spi 0, message ID = -1340288848, sa = 81A7DCEC
May 1 15:19:58.387: ISAKMP:(0:8:SW:1):deleting node -1340288848 error FALSE reason "Informational (in) state 1"
May 1 15:19:58.387: ISAKMP:(0:8:SW:1):Input = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
May 1 15:19:58.387: ISAKMP:(0:8:SW:1):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
May 1 15:19:58.391: ISAKMP:(0:8:SW:1):DPD/R_U_THERE received from peer 120.168.1.24, sequence 0xA3285B8B
May 1 15:19:58.391: ISAKMP: set new node -752454119 to QM_IDLE
May 1 15:19:58.395: ISAKMP:(0:8:SW:1):Sending NOTIFY DPD/R_U_THERE_ACK protocol 1
spi 2182802952, message ID = -752454119
May 1 15:19:58.395: ISAKMP:(0:8:SW:1): seq. no 0xA3285B8B
May 1 15:19:58.395: ISAKMP:(0:8:SW:1): sending packet to 120.168.1.24 my_port 4500 peer_port 52667 (R) QM_IDLE
May 1 15:19:58.399: ISAKMP:(0:8:SW:1):purging node -752454119
May 1 15:19:58.399: ISAKMP:(0:8:SW:1):Input = IKE_MESG_FROM_PEER, IKE_MESG_KEEP_ALIVE
May 1 15:19:58.399: ISAKMP:(0:8:SW:1):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
May 1 15:19:59.887: %SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr=81B51C44, count=0
-Traceback= 0x80137488 0x801DC350 0x801DDDA8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:19:59.887: %SYS-2-BADSHARE: Bad refcount in datagram_done, ptr=81B51C44, count=0
-Traceback= 0x80137488 0x801D8830 0x801DDFD8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:20:05.667: %SYS-2-BADSHARE: Bad refcount in pak_enqueue, ptr=81F84148, count=0
-Traceback= 0x80137488 0x801DC350 0x801DDDA8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
May 1 15:20:05.667: %SYS-2-BADSHARE: Bad refcount in datagram_done, ptr=81F84148, count=0
-Traceback= 0x80137488 0x801D8830 0x801DDFD8 0x801E6860 0x807103F4 0x807F99F8 0x801E698C 0x8043FB10 0x8043FDC8 0x80D23CD0 0x80D24304 0x80D24400 0x8027B3C4 0x8027E9E0
After searching thru the internet, I've found :
CSCsb46264
Symptoms: When a dialer interface is configured as an endpoint for a IPSec+GRE tunnel, tracebacks with bad refcount may be generated.
Conditions: This symptom is observed on a Cisco 837 when router-generated packets such as routing updates are being switched.
Is that possible that the root of the problem was that ? Thank you. -
Getting the messeage request timed out when trying to ping
I can't ping but can be pinged. Done all the steps here: /t5/Hamachi/Ping-Request-Timed-out/td-p/121480 still no succes. I have made rules regarding hamachi in my firewall and i have ran diagonstics in hamachi, it says everything is allright, but still the pings doesn't work. Can be pinged though. I am running Win 10 64bit. But one thing that have caught my interest is this, the hamachi network driver seems to not have a internet connection, but maybe this is normal? : https://gyazo.com/bfbe4e6bcf0b0caff44fdadabaaae865 Translation from swedish:IPv4 Connection: No Network Connection.IPv6 Connection: No Internet Connection. I hope someone out there has the answer to my question! Thanks in Advance!! Best Regards, FiskarN, AkA Elias!
Hi S.Akmal,
The request timed out also can caused by the remote computer no replayed, you can try to check the remote server whether it have some network issue, you also can connect this
server to another server directly(just connect them with cable) then try the ping then can determine whether issue occur on this server.
More information:
Internet Control Message Protocol (ICMP) Basics
https://support.microsoft.com/en-us/kb/170292
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected] -
Got request timed out when ping network load balancing (NLB) cluster ip
I want to set up NLB on windows 2008 R2 64
bit
Server1 : private ip 192.168.1.100 ; public ip 172.1.1.1
Server2 : private ip 192.168.1.101 ; public ip 172.1.1.2
private ip 100/101 can be communicated with each other, but cannot reach from other servers, even with same subnet.
Cluster ip: 172.1.1.3
After created NLB with Unicast, I can ping the cluster ip from these 2 servers, but when I enter the cluster ip in browser, got http 404 not found error; and cannot ping the cluster ip from other servers.
AwenHi,
In your figure, the cluster IP is 172.18.5.22. Does there have some mistype in your post? Another possible is you set the incorrect IP address binding with the IIS service.
More information:
Add and Remove IP Address Bindings
http://technet.microsoft.com/en-us/library/bb734869.aspx
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
Server read lock request timed out in MDM 7.1 server
Hi,
I have a issue regarding the MDM 7.1 server which is on windows 2003 server and Database as Sql server 2005.
The issue is when i am trying to load the MDM server from the MDM console it is popping out the error message as "Server read lock request timed out"
when i restart the server and try to mount the MDM server it is getting mounted but after a while again it popping out the error message.
i saw few log's at batabase and o/s but no luck, Is there a way to solve this issue.
Thanks
Phani RamHi Phani,
I am not quite sure so just have a look at guide u201CGood to Knowu201D Topics for a Smooth SAP NetWeaver MDM 7.1 Implementation
http://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/70b0caa1-92e5-2c10-c687-a8d05e778e59?quicklink=index&overridelayout=true
Page no: 21/96 Example 3: Request for a server/repository read lock timed out where it is said that with MDM 7.1, lock attempts time out in 2 minutes to prevent Consoles from locking up for long times. This is not an error and does not require server to be restarted.
So please go through complete section 5.6 MDM Server Client Requests
Hope it helps..
Regards,
Mandeep Saini -
Does anyone know why I get "The request timed out" when I try to access the iBooks store? If so, is there a solution?
Thanks!You could try the 10.8.2 Combo download. Run the disk utility first before installing, verify your disk then repair permissions.
Then try the Combo downoad http://support.apple.com/kb/DL1581 -
Hi all,
I using the RV042 with the newest firmware version.
Really no idea that i keep got "request timed out" when i try to ping the gateway.
Who have the same issue with me?
Before i think my RV042 is Out of order but still the same after i bought a new one.
WAN: DHCP (ISP)
LAN: 192.168.1.254Hey all,
I am having the same problem with my RV042. Its set up for load balancing with two DSL modems that are setup for access point only (all router functions disabled). I have tried to manually set the MTU first by trying a ping test to determain packet size, then by manually setting the packet size for a full day to see if that size would resolve the issue. I have settled with an MTU size of 1392, but the problem is still there. Any help is appreciated. -
Request timed out because there has been no reply from the server in 600000
Issue:
Request timed out because there has been no reply from the server in 600000
Scenario:
1. All the crystal reports are designed by using Crystal Report 2008 Version -- 12.3.0.601
2. All reports are uploaded to CMC (SAP Business Objects Enterprise XI, Product: 12.1.0)
3. using Front-End .net Winform
4. Crystal Report is binding is done using Business View Manager (since having more than one databases)
5. Business View Manager Connects to Oracle using "Oracle Server" connection
6. Loading reports as follows
string queryString = string.Empty;
SessionMgr sessionMgr = new SessionMgr();
EnterpriseSession enterpriseSession = sessionMgr.Logon(userName, userPassword, serverName, authType);
EnterpriseService enterpriseService = enterpriseSession.GetService("InfoStore");
InfoStore infoStore = new InfoStore(enterpriseService);
enterpriseService = enterpriseSession.GetService("PSReportFactory");
Object psrfObject = enterpriseService.Interface;
PSReportFactory psReportFactory = (PSReportFactory)psrfObject;
queryString = "Select SI_CUID, SI_ID, SI_NAME, SI_PARENTID From CI_INFOOBJECTS " + "Where SI_PROGID='CrystalEnterprise.Report' " + "And SI_ID=" + ReportId;
InfoObjects infoObjects = infoStore.Query(queryString);
InfoObject infoObject = infoObjects[1];
ReportDocument crDoc = new ReportDocument();
crDoc.Load(infoObject, enterpriseSession);
7. All the reports are getting loaded properly and i am able to dynamically set the report parameters
8. After executing report, some of the reports take more than 10 minutes, due to which shows following error
Request timed out because there has been no reply from the server in 600000
Note i have done following:
1. I have checked stored procedure running through oracle for more than 10 minutes (1 hr, 2 hrs)
2. Tried simply running crystal report without front-end running perfectly more than 10 minutes (1 hr, 2 hr)
3. When i run .net winform application for specific reports which takes long time, gives "Request timed out because there has been no reply from the server in 600000"
Also i have done lot much R&D and spent almost weeks to get resolution but not getting any solution out of it, please help me in this case
HKEY_LOCAL_MACHINESOFTWAREBusiness ObjectsSuite 12.0Report Application ServerClient SDKCorbaAdapterWaitReplyTimeout = 600000 and HKEY_LOCAL_MACHINESOFTWAREBusiness ObjectsSuite 12.0Report Application ServerInprocServerEnterpriseRequ
AS per following URL
Session timeout
1. Log into Central Management Console
2. Go to server,right click on Crystal report processing server and select properties,change the idle connection time out to 60 minutes
3. Also right click on crystal report cache server and select properties ,change the idle connection time out to 60 minutes
4. Restart Crystal Report Processing Server and Crystal Report Cache Server
5. Change the session time out to 60 minutes in web.xml of INfoviewApp,InfoViewAppAction,PlatformSerivces and CrystalReports.
6. Navigate to the following location
<BO Install Dir>Business ObjectsTomcat55webappsInfoViewAppWEB-INF
7. Edit the web.xml in notepad and search for the below lines.
<session-config>
<session-timeout>20</session-timeout> <!-- 20 minutes for session objects -->
</session-config>
8. Increase the Session-Timeout parameter to 20 to 60 minutes in web.xml . Save this file
9. Repeat the same for the web.xml file in the InfoViewAppActions folder in <BO Install Dir>Business ObjectsTomcat55webappsInfoViewAppActionsWEB-INF
10. Repeat the same for the web.xml file in the PlatformSerivces folder in <BO Install Dir>Business ObjectsTomcat55webappsPlatformSerivcesWEB-INF
11. Repeat the same for the web.xml file in the CrystalReports folder in <BO Install Dir>Business ObjectsTomcat55webappsInfoViewAppActionsWEB-INF
12. Restart the tomcat server
Still i am getting same error, please help me, if you have any idea, clue with respect to this error on winformThis error is specific to RAS. The default CORBA request timeout is 10 minute = 600000 ms. When the RAS SDK does not get the reponse back from RAS server in 600000 ms it throws this message. Why it works in InfoView\CMC what I believe you refer to as "Front End' application is because InfoView\ CMC don't use RAS.
1. First make sure that a smaller report wich runs pretty fast ( 1-2 min) works. This will confirm that there is no connectivitiy issues between RAS and RAS SDK.
2. If you get the efrror for every single report, even the smaller ones, make sure the box running RAS and RAS SDK code( in case they are 2 different) can ping each other with IP, shortname and FQDN. If there is a firewall between them, the RAS port needs to be opened for bidirectional communication. By default RAS chooses a random port for communication with SDK but within CMC you can configure it to use a specific port and open it.
3. If the issue is specific only to reports that are long running, typically more than 10 minutes, then you need to inclease the CORBA timeout to a value more than what the reports typically would take to process. This is done on client code side or IIS in this case.
Here are the steps:
Make the following changes on the application server/system.
Open RegEdit by going to Start > Run and typing in regedit.exe. Then click Ok.
Navigate to HKEY_LOCAL_MACHINE\SOFTWARE\Business Objects\Suite 11.5\Report Application Server\Client SDK\CorbaAdapter
Change the value of SendRequestTimeout(ms) to 100000.
Change the value of WaitReplyTimeout(ms) to 6,000,000 ms. The default value is 600,000 ms and may not be long enough.
Restart IIS by going to Start > Run and typing in iisreset. Then click Ok.
Retry the failing application.
See note: 1296656
This error should be easy to fix
Edited by: Aasavari Bhave on Feb 2, 2012 11:20 AM -
Request timed out because there has been no reply from the server
Hi,
I am using "Embedded report application server 11.5".
When i am going to launch report with the help of above mentioned server i am getting "Request timed out because there has been no reply from the server for more than 600,000 milliseconds" error.I have already huge data for passed parameter
Steps that i followed:
1)I have set unlimited jobs in server.
2)In registry entry i have set 10,00,000 miliseconds insted of 6,00,000 miliseconds.
Can anybudy please provide me some solution for this.
Regards
VishalSee here if it's still an issue
Re: which registry setting to change for long running reports -
HttpException (0x80004005): Request timed out at Windows Server 2012
Dear All,
I am using "Microsoft Interop Word dll for resume parsing. My functionality is working fine at my local machine. I have two server one is Windows 2008 and Windows 2012 server. I have deployed my code on both server. In Windows 2008 is working find and
in windows 2012 giving exception like -
"HttpException (0x80004005): Request timed out."
When I debug my code at Windows 2012 server. Request going for infinite time and after some time its giving such types of error "HttpException (0x80004005): Request timed out."
It is not able to execute this code of line and going for infinite time -
Microsoft.Office.Interop.Word.Application Application = new Microsoft.Office.Interop.Word.Application();Hello Vivek,
Microsoft does not currently recommend, and does not support, Automation of Microsoft Office applications from any unattended, non-interactive client application or component (including ASP, ASP.NET, DCOM, and NT Services), because Office
may exhibit unstable behavior and/or deadlock when Office is run in this environment.
If you are building a solution that runs in a server-side context, you should try to use components that have been made safe for unattended execution. Or, you should try to find alternatives that allow at least part of the code to run client-side.
If you use an Office application from a server-side solution, the application will lack many of the necessary capabilities to run successfully. Additionally, you will be taking risks with the stability of your overall solution.
You can read more about that in the
Considerations for server-side Automation of Office article.
Consider using third-party components designed for the server-side execution instead. -
Hi All,
I have set up 2 Windows Server 2012 domain controllers (DCA & DCB). DCA points at DCB as the primary DNS, and itself as the alternate DNS. DCB points at DCA as the primary DNS, and itself as the alternate DNS.
When both DCs are running and if I do an nslookup on DCA: The result is as follows:
Default Server: dcb.testdomain.com
Address: 30.30.30.2
nslookup on DCB:
Default Server: dca.testdomain.com
Address: 30.30.30.1
Client PC (Windows 7 Pro):
1st DNS : 30.30.30.31
Alternate DNS: 30.30.30.32
nslookup on the client PC
Default Server: dca.testdomain.com
Address: 30.30.30.1
Up to here everything is fine. Now if I turn off DCA, and do an nslookup, the result is as follows:
DCB nslookup:
DNS request timed out.
time out was 2 seconds.
Default Server Unknown
Address: 30.30.30.31
Client PC nslookup:
DNS request timed out.
time out was 2 seconds.
Default Server Unknown
Address: 30.30.30.31
I waited for more than 15 minutes an tried again, it didn't help.
I have been reading a few similar posts on this matter, but couldn't find the answer.
I would expected it to display the DCB when I do an nslookup.
Question 1: Shouldn't that display DCB rather than displaying a time out message when I do nslookup?
Question 2: The fact that it displays a time out message, does it mean that more configuration needs to be done? If so please kindly advice what needs to be done.
I did an ipconfig /displaydns command. I realized that the order of DNS have changed on both DCB and the Client PC:
Now, they both display DCB on the top of the list, whereas they were displaying DCA on the top of the list prior to the shut down.
Question 3: Does it mean that the Client PC now knows that the 1st DNS is down and so it's using the 2nd DNS?
If so, why does the nslookup display the time out message?
Question 4: Is it possible to configure either of DNS Server or the DNS client, so it displays the 2nd DNS when the first DNS is not accessible and when I do nslookup?
Thank you for.Hi Ton_2013,
Based on my understanding, the issue we are experiencing is that: when the primary DNS server is down, the result of the tool Nslookup is to diaplay the time out message at first. Right?
Based on my knowledge, timed out message is means that the server did not respond to a request after a certain amount of time and a certain number of retries. Because the primary DNS server is down, it can't respond to this request and time is out. When
the primary DNS server can't respond, the secondary DNS server works to ensure effective work. And the order is changed as you said.
As to the reason why the result is still the same even when the order has changed, we can try to use Network Monitor to capture network traffic and view and analyze it to find the cause. And the cause may be the cache. For your information, please refer
to the following link to download the tool Network Monitor:
http://www.microsoft.com/en-hk/download/details.aspx?id=4865
Regards,
Lany Zhang -
SSRS report- Request timed out error displaying when running.
I have a parameter which with other date ranges work but where the parameter for datetime is from 4/1/2013 to 5/1/2013 it brings this error:
Server Error in '/' Application.
Request timed out.
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.HttpException: Request timed out.
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[HttpException (0x80004005): Request timed out.]
How can I be able to determine the cause of this because the sql mgmt studio brings in the data really well at 15 seconds with hundreds of rows?
I am not trying to lessen the time for getting this data which one thing would be to reduce the amount of fields needed to lower reaction time for retrieving the data. I am just wondering why is it giving me this and what plans can I do to avoid these errors
from happening again?Hi Elvin,
The issue might be related to the executionTimeout setting of the Web application. If you view the report in the report manager, please use the following steps to modify the web.config file:
Navigate to <Drive>:\Program Files\Microsoft SQL Server\MSRSX.<InstanceName>\Reporting Services\ReportManager, back up and then open the web.config file.
Search for httpRuntime.
Add maxRequestLength="100000" to the line of code, and reset the executionTimeout value so that the line looks like this:
<httpRuntime maxRequestLength="100000" executionTimeout="90000" />
If you view the reports on a SharePoint site, please modify the web.config file of the SharePoint Web application. For example, if the SharePoint Web application uses 80 port, then its web.config file is located in the C:\inetpub\wwwroot\wss\VirtualDirectories\80
folder.
Hope this helps.
Regards,
Mike Yin
TechNet Community Support
Maybe you are looking for
-
Calling Javascript function from PL/SQL Page Process
Hi All, So far I have seen many threads that answered the question: Calling a PL/SQL from a Javascript function. I would like to know if it's posiible to do the reverse process as follows: DECLARE v_name APPLICANTS.NAME%Type; v_surname APPLICAN
-
Disjointed rollovers using images w/transparency
Hi all! I am trying to build a configurator which will allow me to change different elements (colors) of an object (like a car). In order to do this cleanly and properly, I'd need to use images with transparency, like a PNG/GIF file. 1. Is it possibl
-
Firefox 10.0.2 fonts look weird all of a sudden
'''twitter: ''' *notice the tweets font, it looks horrible * now: http://i41.tinypic.com/25qqkhx.png * how it should be: http://i40.tinypic.com/34xicrn.png '''youtube:''' *notice the titles font, it looks horrible * now: http://i40.tinypic.com/2n9lrt
-
MS SQL administration / backup in SAP
Hi, I have worked mostly with SAP and Oracle environment. Now I plan a backup plan for SAP ECC system with SQL server 2005. So please help me to get some link where I can learn about backup and restore of SQL server in SAP environment. Regards, Nall
-
How to find first non zero value from the numeric value or string?
Hiii, Every body I have one numeric indicator in which some valuse is coming with the decimal value, lets say 0.00013, now i want to find the first non-zero value from this numeric indicator, then what should i do to do so? i have converted