Request turns red in Manage
Hi All,
I have done the init upload but the QM status is red. Monitor is not giving any error. Could anyone help me out?
PB
HI,
Sometimes as depending on the data, the status shows red for some time initially. It doesn't mean that the load is failed. As the system says its still running. Wait for like 1/2 day and if you still see the same thing, you can set the QM status to red and delete the request(if its loaded to ODS or Cube). If its in PSA< you can just delete the request in PSA itself.
From the data load monitor (for this request), on the Header Tab you will find the request number in the form of REQU_____. Copy this and paste in SM37 (source system) between * and *. Chnage the User to * too and F8.
Assign points for useful posts
shreya
Similar Messages
-
The battery icon on my (old) MacBook Pro turned red. Then black. What does this mean?
The battery icon on my (old) MacBook Pro turned red for a few moments, then black. What does this mean?
penny41,
Thanks, glad it helped you to check your battery status.
Something else to look at would be the cycle count, as you mention that your computer is "ancient". If you have a high number of cycles, it may also be a sign that the battery is tired and possibly nearing it's life span, and may possibly need to be replaced soon. If you see that again you may try a SMC reset to see if that helps, but if it continues you may need a new battery at some point. The battery icon will usually say needs service, or something to that effect. For the later MBP's Apple claims a life span of up to 1000 cycles, of this also will be dependent on who the battery is used, on the older ones I'm not quite sure what the claims were, and I don't know how old "ancient" in your case actually means.
I provide this for your info, so that you understand what may possibly be occurring.
I wish you the best.
SMC reset:
Follow directions for what applies to your machine, a battery you can remove, or a battery you should not remove yourself.
Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support -
Red Timeline box. Not render line entire timeline box turns red
I ran into an issue on Premiere Pro cs3 after updating my mac to Mountain Lion. No issues until update. The entire timeline box turns red when I insert a video. Not the render line but the entire box turns completely red. anyone have any ideas?
I realize I need to update, I am a college student, but I do freelance for a nonprofit so I need this up and running as fast as I can.That SEEMS like a case where your graphics driver needs to be updated... but NO way for anyone to tell without hardware information
More information needed for someone to help... click these links and provide the
requested information
-http://forums.adobe.com/message/4200840
-http://forums.adobe.com/thread/416679
-http://forums.adobe.com/thread/419406
ADDED
IF you have nVidia (you did not say) read
Mac & nVidia Driver http://forums.adobe.com/thread/1075592 -
Turn off color management in printer driver?
Hello folks:
When I select an icc color profile in Aperture 3 in the Print dialog box, a warning pops up that says "Turn off Color Management in the Printer Driver." I have an Epson R2880, but for the life of me I cannot find a way to turn it off in the driver. Any thoughts? The Epson Printer Utility is also of no help.
Thank you!
--DavidUnderstanding that I have not actually used ColorJunki:
-- A printer is always going to have something manage color. Either an ICC profile at the application level, or the printer driver.
-- The warning is poorly worded. It means "Turn off the PRINTER color management and let Colorsync manage colors." Thus on the greyed out screen you will see that Colorsync is selected.
-- To use a printer profiler you normally print a target sheet. Your software should tell you what settings to use.
-- Next you read the target sheet and the profiler makes you an ICC profile of your printer/paper combination. (The same process that Canon, Epson, Red River, Illford, et al. follow.)
-- You can now use your new, ColorMunki created ICC profile to soft proof your image as you adjust it and, finally,
-- You use that same profile to print. (Remember, the profile is specific to a printer/paper combination and you will still have to set Quality/Media correctly for the paper.)
By selecting the correct ICC profile on the first print screen, you automatically kill printer color management and, with a bit of luck, a good profile, and clement atmospheric conditions, you will actually get a good print.
Trust me on this, I have been getting great prints from Aperture for years. My only gripe is that AP3 no longer lets me at the color options which I used to tweak for my cheap and cheerful Costco paper. -
Powerline adapters both turn red
After switching off my powerline adapters overnight, they are ok for a few days and then both adapters ethernet and status lights turn red. Does this mean they are faulty or need replacing?
Hi Tyringmybest,
Welcome to the forum and thanks for posting. You should be able to switch off the adaptors without any issues. Have you managed to get this sorted yet? If not drop me an email with your details. You’ll find the “contact us” form in my profile.
Cheers David
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-) -
Internet LED turns Red at a certain time of the day
I have a customer who last year would lose there internet connection like after 4:30pm each day. I was over there a couple days ago and saw it in action. I noticed that on the Actiontec GT704WG modem all the lights would start blinking and then the Internet LED would turn red with all other still green and then it would connect again for a minute and keep going through that cycle. Already did the reset of modem etc. Even happens when the Cat 5 cable is not plugged in. Could this be a power issue with the modem? Also, the ipconfig settings are fine when this is happening... Anyone have any ideas what the issue is? Thank You
All of the lights blinking? Would this include the power lights or only the Ethernet and Wireless lights? If it's the lather, it sounds like the computer searching for a way to the Internet using broadcast packets. The DSL light if it's blinking would indicate a loss of sync, and this can turn the Internet light red. Anyhow, if you can clear up what exactly was blinking, we can continue.
========
The first to bring me 1Gbps Fiber for $30/m wins! -
How to turn off color management in the print dialogue
I Use Macbook Pro OSX 10.8.2
Lightoom 4
Canon Pixma MG 8250
Profile MG series 8200 GL3/SG3 for Glossy paper.
It is stated that "remember to turn off color managment in the print dialog" when using custom profile (I assume the Profile MG...) is regarded as a custom profile...
I have been lookoing in the print dialogue and I can not find any way to turn off colour managment...
Is this only valid for Microsoft Windows of Is there something I do not understand ?Like this :
-
How do I turn off color management in my Epson Stylus Photo R1900
How do I turn off color management in my Epson Stylus Photo R1900 printer? I am using the laetest Epson driver, I am using Adobe Photoshop CS5 and I'm using OSX 10.5.8.
Thanks
JoeI have researched the matter a lot and I,
along with many others, still have problems with this complicated
subject.
Color management is as simple in theory as Honoring a Source Profile and CONVERTING it to a Target Profile (monitor or printer) for Proofing.
But yes, we work at the mercy of the rocket scientists who try to dumb an extremely complicated process down so regular folks (like me) can make it work — trouble is I think their approach needs a bit more distilling and common sense sometimes...but it is very doable once you put in the time to figure it out, just follow the CHAIN in your workflow if you're still having problems.
If you want a "simple button" try staying in sRGB and printing out of Apple Preview app using OEM standard papers matched to your printer and OEM ink set. -
How do i turn off colour management in photoshop cc
i cannot make any sense of the 'help' on being able to see any display which allows me to turn off colour management in photoshop cc or in lightroom 5 when using my Mac 10.9.3
Good day!
What exactly do you mean?
Regards,
Pfaffenbichler -
3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN
Hi Guys,
This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC.
if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
please see below for the boot up of the AP and the WLC logs:
AP
IIOS Bootloader - Starting system.
*** deleted for breverity *****
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
*** deleted for breverity *****
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
*** deleted for breverity *****
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
WLC:
isco Controller) >show time
Time............................................. Tue Jan 27 17:44:47 2015
Timezone delta................................... 0:0
Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
NTP Servers
NTP Polling Interval......................... 3600
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 150.101.176.226 AUTH DISABLED
(Cisco Controller) >show ap join stats summary
Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
(Cisco Controller) >show ap join stats summary all
Number of APs.............................................. 2
Base Mac AP EthernetMac AP Name IP Address Status
f4:4e:05:aa:a6:a0 f4:4e:05:94:c3:98 APf44e.0594.c398 10.1.1.22 Joined
f4:4e:05:b6:ce:f0 N A Test_1 10.1.20.7 Not Joined
(Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 45
- Successful discovery responses sent...................... 21
- Unsuccessful discovery request processing................ 24
- Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
- Time at last successful discovery attempt................ Jan 27 17:45:49.705
- Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
Join phase statistics
- Join requests received................................... 0
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... Lwapp discovery request rejected
- Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
- Time at which the last join error occurred............... Jan 27 17:45:49.705
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : 00:00:00:00:00:00 Ip Address : 10.1.20.7
(Cisco Controller) >show interface summary
Number of Interfaces.......................... 4
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
ap LAG 20 10.1.20.231 Dynamic No No
guest LAG 30 10.1.30.231 Dynamic No No
management LAG 10 10.1.1.231 Static Yes No
virtual N/A N/A 1.1.1.1 Static No No
SWITCH
witch#show run
Building configuration...
*** deleted for breverity *****
no aaa new-model
clock timezone AWST 8
system mtu routing 1500
ip routing
ip dhcp pool WAP_Pool
network 10.1.20.0 255.255.255.0
default-router 10.1.20.1
option 43 hex f104.0a01.01e7
ip dhcp pool Clients
network 10.1.30.0 255.255.255.0
default-router 10.1.30.1
dns-server 203.0.178.191
ip dhcp pool test
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
crypto pki trustpoint TP-self-signed-4082587776
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4082587776
revocation-check none
rsakeypair TP-self-signed-4082587776
*** deleted for breverity *****
*** deleted for breverity ***** !
interface FastEthernet0/3
description *** WLC ****
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/4
description **** AP *****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/5
description **** AP ****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/6
i*** deleted for breverity ***** !
interface Vlan10
description *** Managment ***
ip address 10.1.1.230 255.255.255.0
interface Vlan20
description *** WIRELESS APS ***
ip address 10.1.20.1 255.255.255.0
interface Vlan30
ip address 10.1.30.1 255.255.255.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip http server
ip http secure-server
ip sla enable reaction-alerts
l*** deleted for breverity *****
ntp clock-period 36028827
ntp source FastEthernet0/1
ntp server 121.0.0.42
ntp server 202.127.210.37
end
I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working.
ThanksHey Scott,
I gave that a shot and still no luck, log's from AP boot up:
IIOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 20 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 21 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 67 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 20894208
flashfs[2]: Bytes available: 20006400
flashfs[2]: flashfs fsck took 14 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/Q2.bin
Radio1 present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/Q5.bin
Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP -
Graphics turning Red or Black after a while for no apparent reason?
For some reason every time I import graphics to the library they are fine. But when I put them on the stage (there's about 30 of them in each of different keyframes) they seem to be replaced by black or red rectangles. In the library, they are fine, and when I export them as a .MOV they are sometimes fine. If I export them as an .AVI, however, they remain red and black. It's not all of the graphics, but the longer that I am in Flash, the more of them turn red.
I can't tell if it's one corrupt file or a corrupt installation, but it's been on three computers: a terrible laptop with Windows 7, a Mac, and a modern desktop with Windows 8.
Can anyone fill me in on what might be the cause or possible solutions? (or ways to diagnose it?)My best guess is that you're somehow bumping up against a size limit like this Size limits | SWF, bitmap files | Flash Player 10. I know you're not using the Flash Player, but it's possible that since that limit is known there are limitations in the IDE that are related to it. Have you tried splitting your images into smaller pieces and combining several in the same Graphic symbol?
-
How do I TURN OFF power management???
My computer still keeps going to sleep and the only way to wake it up is to hit the reset button. I tried enabling the keyboard-wake-up to wake it up, but then it started rebooting itself spontaneously every 15 minutes -- without any warning from Windows. It doesn't matter whether I select S1/POS or S3/STR mode -- it does the same thing every time. I don't want S1 or S3 power management. I want to TURN OFF POWER MANAGEMENT COMPLETELY! I only want Windows to turn off the monitor. The BIOS should do nothing!
How do I accomplish this??????????
BIOS v1.3
NEO2-LS
Quickboot - disabled
IDE Busmaster - disabled
ATA mode - native
ATA config - P-ATA only
Performance mode - slow
dynamic overclocking - disabled
S.M.A.R.T. for hd enabled
Power Supply - @Power EP43057 (430W)
HD Western Digital UATA WD800JB
video card - MSI FX5600TD128
512MB Elixir 400 MHz DDR Ram
Lite-On DVDROM
Pentium 4 2.6GHz HT 800MHzQuote
My computer still keeps going to sleep and the only way to wake it up is to hit the reset button
This is strange - my understanding is you would usually use the Power button to wake the suspended PC...
Could what you are experiencing be more of a shutdown or instability?
Is it due to BIOS setting or Windows? Here are some possibilities
1. What is your selected Power Scheme? Are your options for Turn off hard disks, System standby & System hibernates set to Never?
2. These BIOS settings work fine for me ...
ACPI Standby State : Auto
Power Management/APM : Enabled
Suspend Time Out : Disabled
Set Monitor Events
FDC/LPT/COM Ports : Monitor
Primary Master IDE : Monitor
Primary Slave IDE : Ignore
Secondary Master IDE : Ignore
Secondary Slave IDE : Ignore
Set WakeUp Events
Resume on PME : Disabled
Resume on RTC Alarm : Disabled
Keyboard PowerOn Function : Disabled
Mouse PowerOn Function : Disabled
3. Does your keyboard have any of those quick buttons for Power / Sleep / Wake ? Could any of them be stuck? (Mine has these in a most inconvenient place - between Delete/End/PgDn and arrow keys, so I sometimes accidentally pressed them) -
While I was using my iPad, the status bar at the top (the black bar all the way at the top with the clock) suddenly turned red for a very brief moment. Out of the corner of my eye, I saw some words there. But when I shifted my focus to read what was there, the words disappeared and the bar turned back to it's normal black. So I have no idea what this was all about; it was so quick. But it was obviously a warning of some sort.
Anybody know what this could have been?I found it. It says "Garage Band Recording.". Strange, considering it pops up after quitting the app.
-
When I plug in my MacBook Pro to charge, the light is green for a minute and then it turns red and the plug gets very hot. The plug works fine on another computer and charges it. Why won't my MacBook Pro charge?
You performed all of the steps outlined in this link?
http://support.apple.com/kb/TS1567
You uninstalled and reinstalled iTunes?
GB -
Published iWebsite pages turn red when scrolling pages in iWeb
Hi everyone,
Just wondering if I'm the only person who has this issue; when I publish my iweb sites and pages (to MobileMe) all goes well, but when I then scroll my page up and down in iWeb the site turns red again as if I have changed its content.
I've tried the usual stuff (deleted caches, prefs, logged into MM under a bogus username and password) to check if the problem is a MM issue but this also occurs when I publish to a folder...
I've repaired disk permissions and did a fresh install of OS X (10.6.7) two weeks ago.
Does anyone have any other suggestions which might solve this issue? Or perhaps even the same problem?
cheers,
koenBrilliant OT!
Although immediately posting to the discussions group says something about my personal opinion on the reliability of iWeb ... the problem was caused as you expected; the double digit finger action.
So 'no swiping in iWeb' I suppose.
The 'turning red' of published site pages was 100% reproducible by scrolling down using my trackpad, but it doesn't happen when I use my mighty mouse or the arrow buttons/scroll bar thing. (Even although nothing was selected in iWeb, bit of a bug if you'd ask me)
Thanks again for pointing out the logical and to me not so obvious
cheers,
koen
Maybe you are looking for
-
Is there any way to use iPod touch with Win2000/SP4?
Got an iPod touch for christmas... very cool. It doesn't synch with my computer... not so cool. The information I've found - compatibility chart at http://docs.info.apple.com/article.html?artnum=60971 - suggests that I'm SOL with Win2000 - it appears
-
I just installed an x58 pro-e. All is fine, but I want to install a case fan. I don't understand the manual. On page 2-15 the pins are labeled 1. Ground 2. +12V 3. Sensor Okay, I understand 1 and 2, but what does 3 want to sense? I also see "You may
-
Installation of a siebeldb in oracle 9i server
Hi, Im trying to install siebel database server on an oracle 9i server, i have created 2 tablespaces named data02 and am using the existing index file indx as the index for the siebel tablespace. The command that is run in order to set up a schema et
-
HT1212 I forgot passcode on ipad Mini
I just got a new Ipad and the passcode is not working. I have not even synced on a computer as yet. How can I reset and start over? I have no data to lose.
-
I know this has been asked a number of times. I would like to produce umlauts by just pressing alt-a for "ä", alt-u for "ü", alt-o for "ö", alt-A for "Ä", etc. ... I know that i can produce umlaust by typing alt-u and then a, o, or u. I also know tha