Require Logon Using Secure Password Authentication does not work with plaintextlogin on the server side
Hi All ;
We are in the middle of a migration Project but we stuck with this pop3 setting. Most of the mailboxes uses pop3 to connect Exchange 2010 with the setting spa + port 110 on the client side. We want to give same authentication options for the pop3 settings
on 2013 side but when spa is selected the pop3 rejects the connection with the following error.
Your e-mail server rejected your login with SPA.
So both settings for pop3 protocol is same but the client cannot connect from 2013 server.
Where can i enable this feature from Exchange 2013 .
Hi,
Please make sure that we have enabled Outlook Anywhere and 2 pop3 services in Exchange 2013.
More details in the following article:
Enable POP3 in Exchange 2013
http://technet.microsoft.com/en-us/library/bb124934(v=exchg.150).aspx
Please make sure port 110, port 587, port 25 are available.
Please try to disable the NTLM authentication on Exchange 2013 server for testing.
Please also try to run Outlook client under safe mode to avoid some AVs and add-ins.
Please also try to re-create new profile to refresh the caches for testing.
Thanks
Mavis
Mavis Huang
TechNet Community Support
Similar Messages
-
TS3276 when I use cable my mail does not work. with wireless ok
when I use cable my mail does not work. with wireless ok
Unpower and restart it. If that doesn't help, try holding menu and left navigation keys TOGETHER for 6 secs.
AC -
Macbook Pro 2011 DVI HDMI out does not work with TV when the power cable is connected
My Macbook Pro (Early 2011) DVI HDMI out does not work with TV when the power cable is connected. If get the blue screen and then can use the macbook but nothing is displayed on the TV. If i go into display I can see that there are two screens but nothing displayed on the TV. If i take the power cable out at this point the TV shows the second desktop as expected. If i then reconnect the cable, the screen flickers, as though it is being affected by the power cable, and the screen goes blank on the TV. Only if i remove the DVI cable do i get the blue screen again. If i remove the power cable and reconnect it will do it every single time, so i cannot see it being a TV issue or a minor glitch.
I have had this working previously but at the minute it seems to not be playing ball....any thoughts
Thanks
DanBUMP
Any ideas? -
Deskjet D4260 does not work with an ethernet printer server
I am attempting to attach a Deskjet D4260 printer to a home ethernet network using a StarTech PM1115U printer server. The printer has been connected to the network through a desktop computer, and worked perfectly. The printer server will also work with a different printer (Canon i550). However, it doesn't work with the D4260. The server's port will not go online, and it does not appear to recognize the printer.
This occurs regardless of OS (Windows XP, VIsta, 7, and 8 preview all don't work).
StarTech says there is no incompatibility issue with the server and host-based LIDL printers in general or the D4260 in particular. Does anyone know of any issues, or how to get the D4260 to work with this printer server?Yes, that is how the instructions with the server tell you to install it. The server is connected to the network via ethernet cable and the printer to the server via USB. The server's instructions (as well as those given to me from StarTech support) say to install the printer as a local printer using a TCP/IP port using the server's IP address, which must be on the same subnet as the computer you are installing the printer on. All this I have done. There are a number of settings for the port. It can be raw or LPR and there are other options. I have attached it as instructed, and I have tried both raw and LPR, and tried various other settings. I was able to install a Canon i550 on the server with no difficulties. I was able to print to the printer, and the server, when I accessed it using either StarTech's server management software or a browser pointed to the IP address, showed the server's port on line and identified correctly the printer attached to it. When I attach the D4260, however, it shows the port off line and does not identify the printer. I got this server as a replacement for one that I bought without knowing that, according to its own documentation, it does not work with LIDL orinters. StarTech did not have any such warning, and the StarTech support people said that there should be no problem with a LIDL printer. They told me to consult HP support (to which this forum is the closest thing I can find). It looks to me as if either there is something about the printer that needs to be reset, or the server does not work with this printer. So far changing the driver does something, but not enough to print.
-
Juniper Java Secure Application Manager does not work with Snow Leopard
Anyone else having issues as well? I'm not using a client - its basically the Java based application manager for VPN connections to work (so I can remote desktop to my work PC).
Once logged in, it gives a "Restart your browser" error.
Thanks for your helpOK - so I got it to work. Here's what I did. Let me know if it works for you:
I wasn't able to follow the instructions exactly as noted in the original link I posted above.
The terminal command, specifically wget would not work - there is no wget.
I manually downloaded the Java 1.5 version, by following the link (just clicked on it). I 'unzipped' it and moved it into the library/frameworks/JavaVM.framework/versions folder.
So now the 1.5.0 is not an alias (as it is by default in SL), but the older version of Java.
I then followed the instruction related to changing the order in JAVA PREFERENCES.
The final stop - and I think this is key, is that I forced Safari to start in 32 bit mode. You can do this by going to Applications, highlighting Safari and hitting CMD-I. Then check the 32 bit option.
Start Safari, go to the appropriate URL and login. The Java Secure Application Manager should then start as it used to do in Leopard. You should be all set.
Hope this helps - let me know if someone has questions. -
I have weblogic server 5.1.0 with the sp8 running on Windows NT server 4.0.
The weblogic server is configured to use LDAP realm (Netscape directory
server 4.12).
When I try to run weblogic server and I am getting the following errors:
The WebLogic Server did not start up properly.
Exception raised: java.lang.reflect.InvocationTargetException
java.lang.reflect.InvocationTargetException: java.lang.ExceptionInInitialize
or: weblogic.security.ldaprealm.LDAPRealmException: cannot connect to ldapse
without a principal to authenticate as
at weblogic.security.ldaprealm.LDAPDelegate.setupProperties(LDAPDele
.java, Compiled Code)
at weblogic.security.ldaprealm.LDAPDelegate.<clinit>(LDAPDelegate.ja
83)
at weblogic.security.ldaprealm.LDAPRealm.<init>(LDAPRealm.java:34)
at java.lang.Class.newInstance0(Native Method)
at java.lang.Class.newInstance(Class.java:241)
at weblogic.security.acl.Realm.getRealm(Realm.java:78)
at weblogic.security.acl.Realm.getRealm(Realm.java:56)
at weblogic.t3.srvr.T3Srvr.initializeSecurity(T3Srvr.java:1756)
at weblogic.t3.srvr.T3Srvr.start(T3Srvr.java, Compiled Code)
at weblogic.t3.srvr.T3Srvr.main(T3Srvr.java:827)
at java.lang.reflect.Method.invoke(Native Method)
at weblogic.Server.startServerDynamically(Server.java:99)
at weblogic.Server.main(Server.java:65)
at weblogic.Server.main(Server.java:55)
java.lang.ExceptionInInitializerError: weblogic.security.ldaprealm.LDAPRealm
ption: cannot connect to ldapserver without a principal to authenticate as
at weblogic.security.ldaprealm.LDAPDelegate.setupProperties(LDAPDele
.java, Compiled Code)
at weblogic.security.ldaprealm.LDAPDelegate.<clinit>(LDAPDelegate.ja
83)
at weblogic.security.ldaprealm.LDAPRealm.<init>(LDAPRealm.java:34)
at java.lang.Class.newInstance0(Native Method)
at java.lang.Class.newInstance(Class.java:241)
at weblogic.security.acl.Realm.getRealm(Realm.java:78)
at weblogic.security.acl.Realm.getRealm(Realm.java:56)
at weblogic.t3.srvr.T3Srvr.initializeSecurity(T3Srvr.java:1756)
at weblogic.t3.srvr.T3Srvr.start(T3Srvr.java, Compiled Code)
at weblogic.t3.srvr.T3Srvr.main(T3Srvr.java:827)
at java.lang.reflect.Method.invoke(Native Method)
at weblogic.Server.startServerDynamically(Server.java:99)
at weblogic.Server.main(Server.java:65)
at weblogic.Server.main(Server.java:55)
And here is the my ldaprealm.properties file
netscape.server.host=localhost
netscape.server.port=389
netscape.server.ssl=false
netscape.server.principal=uid=admin, ou=Administrators,
ou=TopologyManagement, o=NetscapeRoot
netscape.server.credential=password
netscape.user.dn=ou=People, o=towers.com
netscape.user.filter=(&(uid=%u)(objectclass=person))
netscape.group.dn=ou=Groups, o=towers.com
netscape.group.filter=(&(cn=%g)(objectclass=groupofuniquenames))
netscape.membership.filter=(&(uniquemember=%M)(objectclass=groupofuniquename
s))
By looking at the error message, it seems like the "server.principal" and
"server.credential" info is not correct.
But I was able to use the same Netscape Directory server with Welogic 5.1.0
with sp4, although the ldaprealm.properties file has somewhat different
format.
Did anyone have similar problems with sp8?
Thanks in advance for any suggestions.BEA support just gave me the solution.
They told me to uncomment out the line
server.alias=netscape
in the ldaprealm.properties file
And I am able to start weblogic with my NIS
Thanks
"Enrique" <[email protected]> wrote in message
news:[email protected]...
>
Hi,
Have you try to remove the "system" user on the LDAP server?
Regards.
"Honghai Zhang" <[email protected]> wrote:
I have weblogic server 5.1.0 with the sp8 running on Windows NT server
4.0.
The weblogic server is configured to use LDAP realm (Netscape directory
server 4.12).
When I try to run weblogic server and I am getting the following errors:***************************************************************************
The WebLogic Server did not start up properly.
Exception raised: java.lang.reflect.InvocationTargetException
java.lang.reflect.InvocationTargetException:
java.lang.ExceptionInInitialize
or: weblogic.security.ldaprealm.LDAPRealmException: cannot connect toldapse
without a principal to authenticate as
atweblogic.security.ldaprealm.LDAPDelegate.setupProperties(LDAPDele
..java, Compiled Code)
atweblogic.security.ldaprealm.LDAPDelegate.<clinit>(LDAPDelegate.ja
83)
atweblogic.security.ldaprealm.LDAPRealm.<init>(LDAPRealm.java:34)
at java.lang.Class.newInstance0(Native Method)
at java.lang.Class.newInstance(Class.java:241)
at weblogic.security.acl.Realm.getRealm(Realm.java:78)
at weblogic.security.acl.Realm.getRealm(Realm.java:56)
at weblogic.t3.srvr.T3Srvr.initializeSecurity(T3Srvr.java:1756)
at weblogic.t3.srvr.T3Srvr.start(T3Srvr.java, Compiled Code)
at weblogic.t3.srvr.T3Srvr.main(T3Srvr.java:827)
at java.lang.reflect.Method.invoke(Native Method)
at weblogic.Server.startServerDynamically(Server.java:99)
at weblogic.Server.main(Server.java:65)
at weblogic.Server.main(Server.java:55)
java.lang.ExceptionInInitializerError:weblogic.security.ldaprealm.LDAPRealm
ption: cannot connect to ldapserver without a principal to authenticate
as
atweblogic.security.ldaprealm.LDAPDelegate.setupProperties(LDAPDele
..java, Compiled Code)
atweblogic.security.ldaprealm.LDAPDelegate.<clinit>(LDAPDelegate.ja
83)
atweblogic.security.ldaprealm.LDAPRealm.<init>(LDAPRealm.java:34)
at java.lang.Class.newInstance0(Native Method)
at java.lang.Class.newInstance(Class.java:241)
at weblogic.security.acl.Realm.getRealm(Realm.java:78)
at weblogic.security.acl.Realm.getRealm(Realm.java:56)
at weblogic.t3.srvr.T3Srvr.initializeSecurity(T3Srvr.java:1756)
at weblogic.t3.srvr.T3Srvr.start(T3Srvr.java, Compiled Code)
at weblogic.t3.srvr.T3Srvr.main(T3Srvr.java:827)
at java.lang.reflect.Method.invoke(Native Method)
at weblogic.Server.startServerDynamically(Server.java:99)
at weblogic.Server.main(Server.java:65)
at weblogic.Server.main(Server.java:55)***************************************************************************
And here is the my ldaprealm.properties file////////////////////////////////////////////////////////////////////////////
netscape.server.host=localhost
netscape.server.port=389
netscape.server.ssl=false
netscape.server.principal=uid=admin, ou=Administrators,
ou=TopologyManagement, o=NetscapeRoot
netscape.server.credential=password
netscape.user.dn=ou=People, o=towers.com
netscape.user.filter=(&(uid=%u)(objectclass=person))
netscape.group.dn=ou=Groups, o=towers.com
netscape.group.filter=(&(cn=%g)(objectclass=groupofuniquenames))
netscape.membership.filter=(&(uniquemember=%M)(objectclass=groupofuniquename
s))////////////////////////////////////////////////////////////////////////////
By looking at the error message, it seems like the "server.principal" and
"server.credential" info is not correct.
But I was able to use the same Netscape Directory server with Welogic5.1.0
with sp4, although the ldaprealm.properties file has somewhat different
format.
Did anyone have similar problems with sp8?
Thanks in advance for any suggestions. -
I am trying to trigger a custom event using a program but does not work ..
HI ....i am trying to trigger a custom event of a custom object type using a program but does not work. If trigger the same event using SWUE it works.
below is the code...
{Key = '0010001115'. "Sales Order Number (hard-coded)
CALL FUNCTION 'SWE_EVENT_CREATE'
EXPORTING
objtype = 'ZXXXXXXXF'
objkey = KEY
event = 'ZEVENT'
CREATOR = ' '
TAKE_WORKITEM_REQUESTER = ' '
START_WITH_DELAY = ' '
START_RECFB_SYNCHRON = ' '
NO_COMMIT_FOR_QUEUE = ' '
DEBUG_FLAG = ' '
NO_LOGGING = ' '
IDENT =
IMPORTING
EVENT_ID =
RECEIVER_COUNT =
TABLES
EVENT_CONTAINER =
EXCEPTIONS
OBJTYPE_NOT_FOUND = 1
OTHERS = 2}
Please guide me if i am missing something.Hi Sunny,
I think you should try creating the event using FM SAP_WAPI_CREATE_EVENT.
CALL FUNCTION 'SAP_WAPI_CREATE_EVENT'
EXPORTING
OBJECT_TYPE = 'ZXXXXXXXF'
OBJECT_KEY = key
EVENT = 'ZEVENT'
* COMMIT_WORK = 'X'
* EVENT_LANGUAGE = SY-LANGU
* LANGUAGE = SY-LANGU
* USER = SY-UNAME
* IFS_XML_CONTAINER =
IMPORTING
RETURN_CODE = rcode
EVENT_ID = event_id
* TABLES
* INPUT_CONTAINER =
* MESSAGE_LINES =
* MESSAGE_STRUCT =
Regards,
Saumya -
External USB HD does not work with HAL:
External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era -
New Applications model DOES NOT work with StandAlone OSD media
If you are able to create StandAlone OSD media, the new Applications model DOES NOT work with it.
- The creation of the media will be successful
- The application installation itself will be successful
Yet after the application is installed, it shows the correct process it needs to complete based on the return code in AppEnforce log, but does not process that information back to the the TS Manager so it appears to attempt to download a policy which fails
causing the task sequence to error out..
Thanks,
Squirre1It is very similar to this description:
http://madluka.wordpress.com/2012/05/15/error-0x8000405-when-installing-applications-to-a-workgroup-system-during-build-and-capture-task-sequence/
It is using the application model, since it is not attached to the domain it is on a workgroup. But it is on standalone media and not during a build and capture sequence, it is during an OSD. But alot of the same puzzle pieces fit. Basically pointing to
the new applications model not working during standalone OSD when the MP is not available. i would say that not enough information is getting encapsulated into the Application when exported onto the StandAlone media. -
After upgrading to Lion internal mic does not work with Facetime
After upgrading to Lion internal mic does not work with Facetime. The mic is picking up sound as noted in System Prefs. This was working just fine before the updgrade. Facetime works OK on my iPod.
you have in french a tutorial to recreate your partition here
Rebuild partition with Recovery HD lion after upgrade to 10.7.2
i tested, it's work !
For your wifi problem:
Try to change your setup of wifi, look this table given by apple:
I changed my wifi setup wep to wpa and it's work ! -
Do I need creative Cloud to use Font Folio or does it work with CS6?
Do I need creative Cloud to use Font Folio or does it work with CS6?
The Adobe Font Folio has absolutely nothing to do with the Adobe Creative Cloud offering. I think you are thinking about TypeKit which is included with the Adobe Creative cloud, integrates with the Creative Cloud applications, but also allows use of the fonts therein with other applications.
The Adobe Font Folio is a disk with pretty much the entire Adobe Type Library. You install any number of fonts on the disk onto your system and they act just like any other fonts with any applications, including the CS6 applications.
- Dov -
Outlook 2010 cannot use Secure Password Authentication
I am the administrator of the server running Microsoft Windows 2003 Server POP3 service since 2008. It hosts my email account. Nobody but me manages the settings of the server and the client side. Until the moment I decided to install Microsoft Outlook
2010 as a client there was Secure Password Authentication working between Outlook 2003 and Windows 2003 Server. After installing of Outlook 2010, when I try to sync, the SPA authentication doesn't work. Nothing is changed on the server side.
Enabling the SPA authentication on the both sides results a communicaton problem between Microsoft Windows 2003 Server POP3 service and Microsoft Outlook 2010 client. When I disable SPA on both sides the connection works but password is sent
as plain text. Actually I started a discussion on
http://answers.microsoft.com/en-us/office/forum/office_2010-outlook/outlook-2010-cannot-use-secure-password/66dafd66-1b00-43b5-96fb-b8a26254fc77 but I didn't receive an answer with a solution.Snefels,
This is actually a known issue that Outlook 2010 doesn't work well with Windows Server 2003 POP services.
Here is the blog post for the issue:
http://blogs.msdn.com/b/jjameson/archive/2010/04/26/outlook-2010-does-not-work-with-windows-server-2003-pop3-service.aspx
If you read the comments below, you'll found that some readers' shared some workaround/solutions, which reportedly works for others. So you might want to have a look.
Disable SPA on the Windows 2003 POP3 server and do the same in Outlook 2010 POP setup.. using the full email address, "[email protected]" instead of just doug (if using the Secure Password Authentication).
Aravindhan Battepati -
MAC Authentication does not work
My MAC Authentication does not work.
I have a ACS 3.0 server set. the MAC address is set in the user name field and in the password field.
I can ping the ACS, I can ping my AP, I can ping my client.
I don't want WEP and I don't want LEAP just MAC. So I set my authentication to "Open with MAC" My client has WEP set to NO WEP and authentication to OPEN
I have the latest drivers for both AP and my 350 Client.
I see that the client is associating and disassociating back and forth non stop. My AP log is full with the following message:
Station 0009.7c9f.xxxx Authentication failed
this is my config:
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname GOM_1200IOS
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
server 10.1.2.197 auth-port 1812 acct-port 1812
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa group server radius wlccp_rad_infra
aaa group server radius wlccp_rad_eap
aaa group server radius wlccp_rad_leap
aaa group server radius wlccp_rad_mac
aaa group server radius wlccp_rad_any
aaa group server radius wlccp_rad_acct
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login wlccp_infra group wlccp_rad_infra
aaa authentication login wlccp_eap_client group wlccp_rad_eap
aaa authentication login wlccp_leap_client group wlccp_rad_leap
aaa authentication login wlccp_mac_client group wlccp_rad_mac
aaa authentication login wlccp_any_client group wlccp_rad_any
aaa authorization exec default local
aaa authorization ipmobile default group rad_pmip
aaa accounting network acct_methods start-stop group rad_acct
aaa accounting network wlccp_acct_client start-stop group wlccp_rad_acct
aaa session-id common
enable secret xxxxxx
username Cisco password xxxx
ip subnet-zero
iapp standby timeout 5
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 40bit 7 9DF1C10BF11A transmit-key
ssid GOM_1230
authentication open mac-address mac_methods
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
rts threshold 2312
channel 2462
station-role root
no cdp enable
dot1x reauth-period server
dot1x client-timeout 600
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 172.16.43.45 255.255.240.0
no ip route-cache
ip default-gateway 172.16.47.254
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
ip radius source-interface BVI1
access-list 700 permit 000a.b74c.e8c9 0000.0000.0000
access-list 700 permit 0009.7c9f.d6e0 0000.0000.0000
access-list 700 permit 0006.25b1.2f79 0000.0000.0000
access-list 700 permit 000a.b78b.2d19 0000.0000.0000
access-list 700 permit 000b.5f6e.77c8 0000.0000.0000
access-list 700 deny 0000.0000.0000 ffff.ffff.ffff
access-list 701 deny 000b.5f6e.77c8 0000.0000.0000
access-list 701 permit 0000.0000.0000 ffff.ffff.ffff
no cdp run
snmp-server community GOM_AP1230 RO
snmp-server enable traps tty
radius-server local
group AP1230
user brazil nthash 7 1249523544595F517972017912677A3055325A25770B08770D5C5B4E4478087605 group AP1230
radius-server host 10.1.2.197 auth-port 1812 acct-port 1812 key 7 00233C2B
radius-server retransmit 3
radius-server attribute 32 include-in-access-req format %h
radius-server authorization permit missing Service-Type
radius-server vsa send accounting
bridge 1 route ip
line con 0
line vty 5 15
end
What is wrong?
Thanks very much for your help.I figured out what was wrong so thank you for stopping by.
I will publish the config for other people to see.
Regards, -
i am using firefox 3.6.17 i upgraded it to 4.1.but it does not work properly sometimes it opens every website and most of the time it does not work . so what is the problem please help . thank you
Did you check your security software (firewall)?
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
See:
* [[Server not found]]
* [[Firewalls]] -
Norton password manager does not work on 8. How do I return to a previous version?
when I updated to firefox 8, Norton password manager does not work. How can I return to a previous version. I am surprised that you introduced an update missing this.
Norton needs to be updated.
http://community.norton.com/t5/Norton-360/Firefox-8-Support-for-Norton-Toolbar/td-p/581640
Maybe you are looking for
-
How to properly use finally block
I am writing a try-catch-finally block and I don't think it is written properly. I am using a BufferedReader and BufferedWriter like this: BufferedReader myInput = null; BufferedWriter myOutput = null; try myInput = new BufferedReader(new FileRea
-
Maps missing from "phone view"
I am using Nokia Suite to update the maps on my Nokia 5800. But when I click on the section which should list maps on the phone, only the voice guidance files show up. I have confirmed that the maps are on my phone (for example I just uploaded the
-
Error :-reset pagination
Dear Friend, i am facing one problem in Report Invalid set of rows requested, the source data of the report has been modified. reset paginationHow to remove it ? Thanks Edited by: Vedant on Oct 17, 2011 3:18 AM
-
BAPI for Sales Order item availability check
hi all !!!!!!!!! May I know how to force SO item to perform AV check? What BAPI or function should I use (In custom program, not user-exit)? I use BAPI_SALESORDER_CHANGE to insert or update schedule lines but the confirm qty is always zero!!!! When I
-
I seem to have had the same problem as several people after the recent iOS update. My iPod touch said it needed to update..and then when that hung for about 6 hours, it wanted to restore repeatedly. Had to take it to have the iOS installed (x2) at a