Required quantity and multiple drawing documents in the work centers

Hi Gurus
I have created BOM, which contain item - drawing document, quantity 1 pc.
Irrespective of the total quantity of finished product the drawing document should be only one pc, as we use one document per work center.
However, output of "Required Quantity" using CS03 shows as multiple drawing documents instead of just one drawing document.
Please throw some light on this.
Thanks in advance.
Akshay N.
SAP PP certi.

Hi
In the item details update fixed quantity indicator for the drawing item
so it will be always fixed to 1.
Regards
Abhishek

Similar Messages

Contract Importer - Uploading Multiple Contract Documents for the same MA

Is it possible to upload multiple contract documents against the same master agreement when using the contract importer tool.
If so, what is the format for specifying the various filenames that represent these documents.
Thanks,
Tanmaya

Hi,
Yes this is feasible.
What we had done is uplaoded the MA first and then loaded a separate csv for Attachments. This can then be placed on the desired location and picked up via the attachment importer mapping file. Just FYI, this can be configured in the System properties to import the file into E-Sourcing.
Hope this is helpful,
Vikram

I have changed my icloud email in my iphone but in macbook still using old email. I tried to delete the old email in macbook but it requires password and it does not accept the old password for the old email anymore. How do I remove this old email?

I have changed my icloud email in my iphone but in macbook still using old email. I tried to delete the old email in macbook but it requires password and it does not accept the old password for the old email anymore. How do I remove this old email?

Hello farahani hairon nizar,
If your Apple ID was changed from your old account, you may have to change it back to your old account to be able to sign out and then change it back after that is done. Take a look at the article below for more information.
If you're asked for the password to your previous Apple ID when signing out of iCloud
http://support.apple.com/en-us/HT203828
Regards,
-Norm G.

Will the full version of adobe allow you to review and scroll 2 documents at the same time?

will the full version of adobe allow you to review and scroll 2 documents at the same time?

Sorry, I do not understand what you mean by "the full version of adobe". Do you mean Acrobat?
I am also not clear what you mean by "review and scroll 2 documents at the same time"; please clarify. Adobe Reader (and Acrobat) lets you open as many documents as you want, but if you press Page Down/Page Up on one document, it will not perform that action on the other documents at the same time.

Preparation of AS IS and TO BE Documents for the MM Related Areas

Hi All,
Can you please help me in preparation of AS IS and TO BE Documents for the MM Related Areas.
Thanks in advance.
Unmesh

Unmesh,
You need to have discussions with business to analyse what should be included in TO BE and what should be in AS IS.
You can try preparing the documents, let me know where you get doubts.
Raghavan

How do I display multiple pdf documents in the same window?

I am sure that this question has been asked many times before, but I have searched the forums and the online help documentation for nearly 45 minutes without a satisfactory answer.
I have just installed the trial version of acrobat pro and I want to open multiple documents in the same window but I can't seem to find out how to do it.
Can someone tell me how?
Thanks

This is the worst thing to happen to acrobat, in my opinion.
The clutter that it creates on my computer and the fact that i cant even see the document title when I have a bunch of them open (because the task bar is too full) is unacceptable.
I never would have changed from Acrobat 8 if I had known, and now I cant switch back (company license).
The latest thing i can find about addressing it is here:
http://kb.adobe.com/selfservice/viewContent.do?externalId=kb405108&sliceId=1
which was in november 2008....
why hasnt any thing else been done about it? I just spent 45 minutes being sent to different departments over the phone, only to be told to submit a feature request.
Please do this if you havent already:
http://www.adobe.com/cfusion/mmform/index.cfm?name=wishform

Printing Multiple PDF documents on the fly

Hello all,
I am looking for a solution for printing the documents to a PDF file. My requirement is that from the application, I can select a set of documents (say 50 numbers) and give for print. The program is in MS access. The MS access opens the report required for generating the documents, pulls the data from the database and generated the document. this will in turn go to a default printer set on the application server. The program repeats for all the 50 dcouments and prints each of them in paper.
All I need know is instaed of printing, all the documents should get mergerd to a single PDF file. Once all the documents are merged I can give it an appropritae name and save it.
Do let us know this is possible by installing a PDF printer driver from adobe on the application server. Will it automatically convert all the prints given at one go to a PDF file or any change in code is required to do it.
Regards
Cherian

FYI, when you use the Adobe PDF Print driver that comes with Acrobat, the PDF Producer won't say "Adobe PDF Converter".
When using the Adobe PDF Print driver, you should see:
Application: Pscript5.dll 5.x.x
PDF Producer: Acrobat Distiller X.x.x
If your document says "Adobe PDF Converter" then it was created by 3rd party software, most likely this package:
http://www.clicktoconvert.com/pages/adobe_pdf_converter/index.htm
That is NOT Adobe software. Please clarify what version of Reader/Acrobat you are using so that we can properly help you. If you need help with your 3rd party PDF print driver, you should contact the company that developed it.

Requirement quantity and quantity withdrawn are not matching

From a production order the requirement quantity of one component is 4 and for another component, it is 2. But the withdrawn quantity for the first component is 5 and for the 2nd component it is 0. This has caused a COGI error.
Also the total quantity and the delivered quantity is shown as 6.
How can this be corrected and prevented from happening in the future.

Hi Jeby,
Thanks very much for your reply.
Batch management is not used for both the components.
For both the components the storage location is mentioned in the components overview of the production order. When I checked in the material master the same storage location is existing in the materiala master also

Pages document will not open, it says I need a newer version of Pages. I have already installed and created this document in the new version of Pages

I just created a document in Pages. Now when I try to open my document in Pages I am given a message that I need a newer version of Pages to open it. When I go to the Appstore it shows that I have already downloaded the latest version.

You have 2 versions of Pages on your Mac.
Pages 5 is in your Applications folder.
Pages '09/'08 is in your Applications/iWork folder.
You are alternately opening the wrong versions.
Pages '09/'08 can not open Pages 5 files and you will get the warning that you need a newer version.
Pages 5 can open Pages '09 files but may damage/alter them. It can not open Pages '08 files at all.
Once opened and saved in Pages 5 the Pages '09 files can not be opened in Pages '09.
Anything that is saved to iCloud is also converted to Pages 5 files.
All Pages files no matter what version and incompatibility have the same extension .pages.
Pages 5 files are now only compatible with themselves on a very restricted set of hardware, software and Operating Systems and will not transfer correctly on any other server software than iCloud.
Note: Apple has removed over 100 features from Pages 5 and added many bugs:
http://www.freeforum101.com/iworktipsntrick/viewforum.php?f=22&sid=3527487677f0c 6fa05b6297cd00f8eb9&mforum=iworktipsntrick
Archive/trash Pages 5, after exporting all Pages 5 files to Pages '09 or Word .docx, and rate/review it in the App Store, then get back to work.
Peter

How do I use a counter to measure frequency and multiple analog signals in the same VI?

I have a PCI-6071E, an SC-2345 with multiple modules, and a PXI-8184 (with a PXI-1002 Chassis).
My goal is to monitor pressures, flows, temperatures, and speed in one VI.
I am using Measurement and Automation Explorer version 3.1.1.3004 to manage my channels.
My speed is a PWM signal which I recently rewired through the counter 0 of my board.
I was hoping to configure this to read frequency directly in measurment
and automation, have this scale the value to RPM, and then feed it
directly in to my labView program.
In labView, it will not except this signal though.
I get error -200300 from the DAQmx Start Task.vi
Possible reasons(s):
Invalid timing type for this channel.
Property: SampTimingType
You Have Requested: Sample Clock
You Can Select: Implicit, On Demand
After doing some research, it seems that the counter wants "Implicit"
selected for the DAQmx Start Task.vi, but then I cannot use my other
channels. Also, counter is included in the "Sample Clock" option
description, so I do not understand why it is not working.
Does anyone know how to work around this problem or a way to configure the counter so that it will work in this way?
All my other channels are Analog.
Thank you.

I am working on getting just the counter working by using
the program posted previously, and I am running into issues. Periodically I get
the error:
Error -200141
occurred at DAQmx Read (Counter DBL 1Chan 1Samp).vi
Possible reason(s):
Data was overwritten
before it could be read by the system.
If Data Transfer
Mechanism is Interrupts, try using DMA. Otherwise, divide the input signal
before taking the measurement.
It seems to work better if I use cascaded counters, but I need timer 0 for
analog channels when I run this code along with the program for the other
measurements.
I have tried averaging, and selecting different values for the millisecond
timer, and these did not seem to have an effect.
I tried different DAQms configurations and "Counter DBL 1Samp" seemed
to work the best.
The program will work for a while and then it will give me the above error
message.
If I use counter 0 as a cascaded counter input, the program runs fine. If I run
this with other analog channels, it errors out because the analog channels use
counter 0.
If I use counter 1 as a cascaded counter input, it seems to work better than a
single channel, but it will still error out with the above error.
If I use only counter 1, I get the error above even faster.
Also, none of the
configurations give measurements outside the While Loop.
The only place I can add a speed dial for the front panel is within the While
Loop.
Is there someway to get the signal to continuously send out of the while loop?
I thought if I could get the signal out of the while loop, I could condition it
anyway I wanted without the program erroring out.
Any suggestions would be much appreciated.
Thank you.
Attachments:
Counter_error.jpg ‏45 KB

No SIM on iPad. Tried different cards, same thing. Updated and multiple reboots have solved the problem. IPad fault?

No Sim on iPad. Tried different cards, same thing. Updated iOS and multiple reboots, no luck. iPad fault? What do I do now, ask for replacement?

Apple has acknowledged that the "no sim card" message has been a problem for some users. iOS 5.1 is reported by MacWorld to resolve this issue. 5.1 is in development and a beta version has been seeded to developers. In the meant time I suggest contacting Apple.

Attaching a word document to the work item

Hello Everyone,
I want to send an attachment with the work item. My requirement is as follows.
Iam working on CRM. The Business Object which Iam using is BUS2000116. In this Activity, there is an attacment tab. Here the user will generate a word document which is populated with the values from the Activity.
I need to send this word document as an attacment through a work item when status gets changed.
I can send the work item. But in my BO BUS2000116, the attachment is not being shown. So I can't do any binding to the Container element Attach_objects.
Please let me know how to achieve this.
Regards
Hari

Use SAP_WAPI_ATTACHMENT_ADD function module.
or There is also a step type in 4.6 you can use in the workflow -Generate
Document from a template. You can create doc template (e.g. using
MS Word) and insert a placeholders in the text which would at
generation time be substituted with values from corresponding container
elements.
<inappropriate content removed by moderator>
Thanks
Yogesh Sharma
Edited by: Mike Pokraka on Jul 1, 2008 1:34 PM

Script for moving multiple subtitle clips in the works - EXAMPLES NEEDED!

Hi everyone!
One severe deficiency of DVD Studio Pro is the inability to move multiple subtitle clips back or forward in a track by an arbitrary offset.
I ran into this problem while I was creating a DVD from an EyeTV recording of a DVB broadcast, the subtitles from which have to be extracted to a SON file and a bunch of .bmp images with a separate piece of software, ProjectX. For some reason, ProjectX messed up the subtitle timecodes, so I had to move the entire track forward by a fixed amount. Unable to do this inside DSP, and unable to find tools that would do this for SON files, I set out to code my own tool with Python.
Currently, I have a very simplistic working version of the script, which I successfully used to shift the timecodes of the aforementioned SON file.
This got me thinking: I can't be the only one who has faced this problem. So, in the spirit of giving something back to the community, I thought I'd try my hand at turning this little script into a versatile tool for timescaling several different subtitle formats.
If possible, I would like to receive real-life examples of several different plaintext (no binary formats, thanks) subtitle formats from you guys, both those that DSP supports and those that it doesn't.
For now the tool only shifts entire tracks and works on the command line, but who knows, maybe I'll create a GUI at some point and add the ability to shift specific subtitle clips instead of whole tracks - time permitting, of course.
If you think you might have some juicy subtitles laying around, please reply or contact me directly by e-mail: elamaton (at) nic.fi. Don't worry, I won't redistribute anything you send me, it will only be used as test data.
iMac Core Duo 20" Mac OS X (10.4.7)

Sounds like a very good idea... but have you seen Subtitler:
http://www.versiontracker.com/dyn/moreinfo/macosx/26322
Not to say you won't make a better version, and I'd be delighted if you did! Manipulating subs in DVDSP is not something I do any more - I use an external text editor for any job where more than a few subs are needed.
The problem in DVDSP is that you cannot extract the subs directly, you have to export an track item description which has the subs and time code buried within the XML. You might find that PHP will give you a web based tool to extract the subs and time codes and write a text file, which you can then manipulate.
In fact, wouldn't a web based tool be a good idea? People could upload the track description, it would export the subs and you could get it to adjust the timecodes and write a text file back in the correct format to import back in to DVDSP. Once the subs are in a text file it is a simple matter to manipulate them further...

IE7 and Multiple Embedded SWF Videos Not Working

We have a page that contains 2 videos that are streamed from our media hosting company. The code is fairly straightforward,
<object type="application/x-shockwave-flash" data="http://xxx.xxx.xxx/your.swf" width="400" height="300">
<param name="movie" value=http://xxx.xxx.xxx/your.swf"" />
<param name="allowFullScreen" value="true" />
<param name="wmode" value="transparent" />
<param name="allowScriptAccess" value="always" />
<param name="flashvars" value="streamer=rtmp://zzz.zzz.zzz/zzz.flv&autoplay=false" />
</object>
Similar code is used for the second video. The embed code is actually generated from the hosting company and has worked every time. Firefox and Chrome display both videos with no problem. However, IE7 only displays the second video. The first video just has white space where the video should be.
I have used 'embed' tag and conditional object tags (for IE), rewritten the code from scratch, changed the z-index, used Flash to generate code, cleared the cache - all to no avail. Is IE7 incapable of having multiple SWF files on the same page?
**I did notice that changing the autoplay attribute to true will allow for the video to display, however, the playback controls are not available.
Any ideas on how to get this working in IE7?
Thanks in advance

Another me too. In particular the symptoms are this:
+ any YouTube video embedded within a webpage loads the poster frame and the controls, but after clicking the play button only shows the progress indicator briefly before showing "An error occurred, please try again later." within the video frame.
+ the same YouTube videos play fine on the YouTube site.
+ other Internet video plays fine, embedded or not.
+ when the error occurs Safari reports "One error in opening the page. For more information, choose Window > Activity".
+ the Activity window shows "forbidden" for http://v13.lscache4.c.youtube.com/videoplayback?ip=0.0.0.0&sparams=id%2Cexpire%2 Cip%2Cipbits%2Citag%2Calgorithm%2Cburst%2Cfactor%2Coc%3AU0dWSVhMVV9FSkNNNl9QRllH &fexp=900028&algorithm=throttle-factor&itag=34&ipbits=0&burst=40&sver=3&expire=1 274817600&key=yt1&signature=C15947474FA80C9A1B9DA597103C5FF7D621A478.0C1490DE456 5D519F602B0043A4E1F9D800417A0&factor=1.25&id=c3e8886e8b459334
+ the same URL downloads fine when visiting YouTube directly, except the signature value is different.
I have tested the following:
+ the same computer worked fine a week or so ago
+ other computers on the same shared ADSL connection work fine
+ Firefox works fine (contrary to other's experiences)
+ deleting com.apple.Safari.plist doesn't help
+ disabling/enabling the "Enable Plug-ins" preference doesn't help
+ deleting Preferences/Macromedia folder doesn't help
+ reinstalling Flash doesn't help
+ empty cache doesn't help
Tis quite perplexing.

Availability of the Work Centers

Hi all ,
I have work centers (ARBPL) with me .
I have to find when these work centers are available (if already work for other orders) .
IS there any FM to find this .....
Regards
Raj

Sreekant Bilihalli wrote:
Hello Experts,
>
> I am trying to design a solution where, during rough cut planning for a material (SOP), the user can check the capacity availability of his work centers / resources. I can see there is a standard link in the rough cut plan:
>
> Views >> Capacity situation >> Rough cut planning
>
> I am not able to see the capacities of my work centers. What am I doing wrong here? Is this the correct way to check the capacity situation during rough cut planniing? Please help me. Thanks.
>
> WR,
> Sreekant
Dear,
First create a rought cut planning profile MC35 - Create. Enter Info structure and execute then plant material and then rough cut planning profile data against resources.
Create flexible planning MC93 against only this material and enter quantity in periods and then follow path >Views >> Capacity situation >> Rough cut planning
I hope this will solve your issue.
Check and revert back.
Thanks
Muhammad Ashfaq

Required quantity and multiple drawing documents in the work centers

Similar Messages

Maybe you are looking for