Requirement Types for Independent Requirements: LSF, VSF, VSE

Hi,
(1) Can anyone explain the following requirement types in layman's terms:
LSF (Make-to-stock production)
VSF (Planning with final assembly)
VSE (Planning without final assembly)
(2) Upon transfer to demand management, how to determine which Requirement Type to use?
Thanks.

Hi,
Requirement type determines the following points:
1. Consumption of Independent req & customer req.
2. How warehouse stock taken into account.
3. Make to order or Make to stock.
4. Planned order can be released or not.
Requirement class is assigned with requirement type.
PIR requirement type & customer requirement type both linked with Strategy group.
Ex: For strategy 10, PIR req type is LSF & Customer req type is KSL.
So transfer to demand management in the material master if strategy 10 is assigned, system will take req type as LSF.
Same as if strategy 40, req type VSF
For strategy 50, req type VSE.
Regards,
Dharma

Similar Messages

  • Idoc type and message type for Planned Independent Requirement (PIR)

    Hi
    Can anyone please give me the information on the idoc type and message type for Planned Independent Requirement(PIR)?
    And also the prerequisites to use them.
    Regards,
    Lohitha
    Moderator message: please do more research before asking, show what you have done yourself when asking.
    Edited by: Thomas Zloch on May 23, 2011 10:45 AM

    Hi,
    You can use IDoc type WMMBID02 with message type WMMBXY.
    Also please check test program RLMBXY00 to simulate IDoc WMMBID02.
    Regards,
    Ferry Lianto

  • How the system determines the Requirement type  for one sales order

    Hi,
    SAP-SD Gurus,
    Please tell me how the system determines the Requirement type  for one sales order?
    Thanks & Regards,
    Sreenivas.P

    Hi,
    System follows some search criterial to determine the requirement type
    1. First, an attempt is made to find a requirements type using the strategy group in the material master.
    2. If the strategy group has not been maintained, the system will determine it using the MRP group.
    3. If the MRP group has not been defined, the system uses the material type instead of the MRP group when accessing the corresponding control tables.
    4. If no requirements type is found here, the system assumes a special rule and attempts to find a requirements type with the aid of the item category and the MRP type.
    5. If this is not possible, a last attempt is made to find a requirements type with the item category only.
    6. If the last attempt fails, the system declares the transaction as not relevant for the availability check or transfer of requirements.
    Please check the path
    SPRO->SALES & DISTRIBUTIONS->BASIC FUNCTIONS>AVAILABILITY CHECK AND TOR->TRANSFER OF REQUIREMENTS--->DETERMINATION OF REQUIREMENT TYPE USING TRANSACTION.
    Hope it will clarify
    regards,
    santosh

  • Different Document Type For MRP Requirement

    Hi  All,
    Can any one help me for this issue...
    MRP run creates PRu2019s for externally procured materials with document type NB, is it possible to have different PR document types for MRP generated Std PRu2019s and Sub contracting PRu2019s without nay enhancement.
    Thanks
    Praveen
    Edited by: Praveen Kumar Shukla on Sep 9, 2009 1:19 PM

    Hi
    You can set different MRP doc.type:  purchase requisitions for standard purchase order /  purchase requisition for subcontracting / purchase requisition for subcontracting  at MRP group level
    Using transaction OPPR u2013 Select plant u2013 Select/create MRP group  under External procurement screen click on Scheduling/doc type.
    And make sure that in material master u2013MRP1 view you are maintaining this MRP grp.
    with regards,
    VB

  • Configuration setting required to configure the O/P type for GR

    Hi,
    Can you explain or give the link how to configure the O/P type for GR, Return delivery , like WE03, WE01 etc.
    regards,
    zafar

    Hi,
    For custom print, you need to maintain below settings.
    1. Maintain Condition Tables
    Menu Path: IMG / Materials Management / Inventory Management and Physical Inventory / Output Determination/ Maintain Condition Tables
    Transaction: M703
    2. Maintain Access Sequences
    Menu Path: IMG / Materials Management / Inventory Management and Physical Inventory / Output Determination/ Maintain Access Sequences
    Transaction: SPRO
    3. Maintain Output Types for IM Documents
    Menu Path: IMG / Materials Management / Inventory Management and Physical Inventory / Output Determination / Maintain Output Types
    Transaction: M706
    4. Maintain Output Determination for IM Documents
    Menu Path: IMG / Materials Management / Inventory Management and Physical Inventory / Output Determination / Maintain Output Determination Procedures / Condition: Procedure
    5. Create IM Documents Condition Records
    Menu Path: IMG / Materials Management / Inventory Management and Physical Inventory / Output Determination / Maintain Condition Records / Create Condition: Inventory Mgmt
    Transaction: MN22
    Also check following:
    1 Define Printer...at OMBR
    2. Enable material doc printout at OMB5
    3. Assign form at OMBU
    4. Also Assign the printer to WE01 output type in OMJ3 Tcode with combination of Plant + Storage location
    5. Maintain the condition record in MN21 or NACE for individual slips or collective slips.
    After doing the above steps you need to select the print button when you are doing MIGO_GR and select the slip types like individual or collective.
    If you maintain the condition record as print immediately you will get the print out immedialtley when save the document otherwise run T.code MB90.
    Note:
    WE01-INDIVIDUAL SLIP PRINT SELECTION IN MIGO
    WE02-INDIVIDUAL SLIP ALONG WITH INSPECTION SLIP
    WE03-COLLECTIVE SLIP IN MIGO
    Regards,
    Biju K

  • IDOC type for interface between SAP ECC and SAP F&R

    Hi Experts,
    I need SAP standatd IDOC type for interfacing between SAP ECC and SAP F&R [SAP Forecasting and Replenishment] using message type u201CFRE_LOC_SITEu201D.
    Please help me in finding the idoc type?
    Regards,
    Krishan

    Hi Denish,
    You have 2 ways of loading data from R/3 to APO.
    1. R/3 to BW cube to APO-BW cube to APO planning area
    or
    2.  R/3 to APO-BW cube to APO planning area   
    BW can be a enterprise BW system ( independent) or you can use the BW inbuilt in APO also referred to as APO-BW.
    The only difference between the 2 BW systems is APO-BW can not take the load of reporting where as the enterprise BW can.
    Unless your company policy requires the enterprie BW system, I suggest using 2nd way.
    You can load the data from R/3 to APO-BW cube using extractors either generic or standard depending on your data. You need to have a RFC connection setup between APO-BW and R/3. ( This is not CIF).
    When you load the data into the APO-BW cube, you just have to load the data from the cube to APO planning area using the transaction /sapapo/tscube.
    Refer to [DP Data Mart|http://help.sap.com/saphelp_scm50/helpdata/en/13/5ada58309111d398250000e8a49608/frameset.htm] for more information about the data transfer between APO-BW and APO.

  • Output types for delivery documents

    Hi All,
    Please help me out.
    Thanks in advance,
    Here i got a requirement like i already have the output types for the delivery documents.However i need to copy the existed output types into different names bcoz to customize it for different organization in different region.
    The problem is i already copied the o/p types but when i went to vl03n and tris to see the output , am not able to find my o/p type there...am i need to do anything more..
    Please help me out as i am a ABAPER and not the functional guy am facing lot of  difficulty...
    again thanks in advance.

    dear govardhan
    please refer below
    Output Determination Procedure
    Output is a form of media from business to one of its business partners. The output can be sent to any of the partners defined in the document. Outputs are usually in the form of Order Confirmations, Freight List, Delivery Notes, Invoices & Shipping Notifications. Determining form of output is output determination
    Types of Output: Print Output, Fax, Telex, E-Mail & EDI (Electronic Data Interchange)
    PRINT OUTPUT:
    SPRO- IMG- Basic Functions- Output Control- Output Determination- Output Det using Cond Tech- Output Det for Sales Documents & output determination for billing documents.
    Create Condition Table: select the field Sales Doc Type from field catalog & Save
    Maintain Access Sequence: 4-digits code & description. Assign condition table to access sequence. Select Accesses line item and Goto Fields. Fields will display the fields we have selected in the condition table i.e. sales doc type.
    Select BA00 & Copy & Rename. Give the same 4-digit code as given to acc seq.
    You Can Maintain:
    Languages of Output
    Partners (to whom we want to send output)
    Print Program- print specification
    Sap Script- layout
    Assign Output Types to Partner Functions: go to new entries & assign your output type to partner functions.
    Maintain Output Determination Procedure: V10000 (Standard Procedure). Go to new entries & create your own 6-digit code with descp. Select the procedure & go to Control Data. Here mention the output type i.e. cond type & leave requirement and manual only columns as blank.
    Determination Rule: link the 6-digit procedure code to doc types.
    Create Condition Records: VV11. Select document type and click on Communication. Mention partner function, medium, time. Output device: LP01, Spool request Name: SD_003, Suffix 2: order_confir & flag on print immediately.
    Once you press enter you will come across 2 key combinations:
    Sales organization/ Customer Number: fill SO, Customer No, Partner Function Abbreviation, Partner to whom the output should be sent, time, medium, language. {It contains: Sales Orgn, Customer, Partner Function (The abbreviated form of the name that identifies the Partner) (During output determination, the system determines the recipient of the output from the master record for the specified partner function. In this field, you can explicitly specify a recipient that will override the standard partner. There must also be a master record for the partner that is specified explicitly.), Medium, Time & Language.}
    Order Type: Document Type, Partner Function (abbreviation), Partner, Medium, Time & Language.
    In SAP we can send the documents to respective partner functions through different transmission mediums. SAP uses condition technique to determine output t relevant partners with relevant transmission mediums.
    Out put determination procedure has a integration with technical module, as ABAPer’s  has to write SMART forms and FORMS to print the output , that SMART form output can be send to relevant partner function through relevant transmission mediums.
    Out put determination procedure for order confirmation: (V/57)
    a) Maintain condition table:
    Path:
    IMG
    SD
    Basic functions
    Output control
    Output determination
    Output determination using the condition technique
    Maintain out put determination from for sales document
    Maintain condition tables
    Maintain out put condition table for sales document
    Here we define condition table
    Ex: 007 – order type (sales order types)
    Save it
    b) Maintain output types:
    IMG
    SD
    Basic functions
    Output control
    Output determination
    Output determination using the condition technique
    Maintain out put determination from for sales document
    Maintain out put types
    Here we define out put types
    Ex:     AF00 -- Inquiry
         AN00 – quotation
         BA00 – Order confirmation
         BA01 – EDI odd response
         KRML—Credit processing
         LP00 -- Scheduling agreement
         MAIL – Internal message
         RD03—cash sales invoice
    Choose BA00 copy it and rename as a ‘MA00’
    click on details icon
    click on display to change icon
    then again choose ‘MA00’ click on details icon
    Maintain data in general data tab
    General data tab:
    Access sequence: 0010(order type)
    In IMG define access sequence and assign to the output type
    Check access to conditions:
         This indicator allows the system to read the condition records for output. If it is not been activated then system determines out put from customer master ex: By following out put determination procedure “DB0001”
    Check cannot be changed:
         This control specifies whether the out put can be changed or not
    Ex: direct mailings can be changed during processing
    Check multiple issuing:
    This indicator allows the system to send the output multiply
    Ex: sales order has been sent for 10 items again one item has been added to sales order so that business has to issue the new out put for sold to party with added line items. This indicator allows the system to send out put repeatedly.
    Check partner independent out put:
    During output processing when the indicator has not set then system allows only specific functions in specific partner functions
    Don’t write processing:
    This indicator determines whether system has to write processing log for output
    Default values tab:
    Dispatch time:
    Ex: send immediately: when carry the application this indicator determines when the output should be sent.
    Transmission medium:
    Ex:     print out
         Fax
         Telex
         Internal send
         EDI
         Simple mail
         Special function
         Events (SAP business workflow)
         Distribution (ALE)
         Tasks (SAP business work flow)
    Specify the transmission medium through which the output should be sent. (Ex: print output)
    Communication strategy
    Specify the communication strategy if you want to send the output externally
    A) Time tab:
    Check timing: (Periodic job not allowed)
    This indicator allows the system to carry out print program periodically.
    B) PRINT NEXT TAB):
    Print parameter: Ex sales org.
         Specify the print parameter.
    Click on mail title & Text control button under dialog structure.
    Here we assign title for the mail along with relevant text Ex:-EN (English)
    Processing routines control button under dialog structure.
    Here we assign programs form routines & form that are written by ABAPER, they           they various transmission mediums.
    Ex; - Transmission medium      shortest      program     form routine
              1                  print out     RVADOR       entry
    Click on position function control button here we assign relevant partner function to relevant transmission mediums
              EX: print out: SP (Sold to party)
    C) Maintain access sequences:
         Here we define Access sequence.
    EX: 0010 & Assign the condition tables to this output.
    D) Assign out put types to partner function:
         Here we assign output types along with transmission mediums to relevant partner functions.
    EX:      Out put type          Transmission medium
           MA00                    1
              “                    2
              “                    6
              “                    A
           MAIL                    7
    E) Maintain output determination procedure:
         Here we define output determination procedure
    Ex:     V10000     -     Order output
         V05000     -     Inquiry output
         V06000     -     quotation output
         V10001     -     Cash sales output
    Choose output determination procedure EX; V10000, copy it& rename it as MA0000
    Assign output type MA00 by going control date section.
    Save it.
    F) Assign output determination procedures;
    Allocate sales document Header.
    _ Choose sales document type OR & Assign output determination procedure i.e MA0000 & Assign output type MA00.
    Assign sales document items.
    -Choose item category TAN & Assign output determination procedure Ex: Ma0000
    - save it & exit.
    Maintain output records (vv11)
    Path:
    Logistic > S&D > Master data > output > sales document > VV11 – Create
    Specify output MA00, Click on Key combination & specify sales document type (OR), partner function (sp) transmission medium (1) dispatch type (4) language (EN)
    Click on communication button on application tool bar
    Specify output device – LOCL or LP01
    Check print immediately check release after output
    Save it
    Go to Va01 raise the sales order
    Go to extra button output header edit.
    Specify output type: MA00 partner function
    Select line, click on communication methods
    Specify logical destination
    Check print immediately
    Check release after output
    go back save it & exit
    Go to VA02, Go to Extras output header print preview
    Check out (order confirmation
    (ERROR: out put MA00 for partner cannot be processed)
    rewards pls
    siva

  • Movement Types for Receipt and Consumption

    Dear all,
    I am an ABAPER.
    My requirement is to develop a Material balancing report.
    In which i have to display
          Opening Stock
          Value
          Receipt
          Value
          Consumption
          Value
          Closing stock
          Closing value
    for a material.
    Here I need to know the table and fields for the above mentioned output fields.
    Particularly i need to know what are the
    movement types for Receipt and
    movement types for Consumption
    Can anyone let me know?
    Regards,
    Prem

    hi,
    few reports are:
    MC45 INVCO: Analysis of Usage Values
    MC46 INVCO: Analysis of Slow-Moving Items
    MC47 INVCO: Analysis of Reqmt Values
    MC48 INVCO: Anal. of Current Stock Values
    MC49 INVCO: Mean Stock Values
    MC50 INVCO: Analysis of Dead Stock
    MB51......
    TAbles:
    MVER - Material consumption.....
    MARC Plant Data for Material
    MARD Storage Location Data for Material
    MSLB Special Stocks with Vendor
    MSPR Project Stock
    MKOL Special Stocks from Vendor
    MSKU Special Stocks with Customer
    you can see al the mvt types in T156 table...
    Hope it helps...
    Regards
    Priyanka.P

  • How to allow create different transaction type for different customer

    We are using CRM 7.0 now. We have two types customer, one is sap customer, the other is potential customer. We want to distinguish the two types customer. And user can create all transaction (for example: quotation, opportunity, activity) the sap customer. And the user only can create activity for  the potential customer, they can't create others transaction type for potential customer. How can we realize it? Thanks.

    Hi,
    We can make use of the BLOCKING REASONS to realize your requirement.
    A Blocking Reason can be assigned to the Business Partner role dependent data  and to the transaction type. A Business partner can be used in a transaction only if he is not assigned to this blocking reason.
    For Ex, In your scenario you can create a Blocking reason 'Not a SAP Customer ' and assign it to all the Potential Customers. You should assign the blocking reason to all the transaction  types which the potential customers should not be allowed.
    Hope it helps. Please let me know if you need further help.
    Regards,
    Vamsi.
    Edited by: Vamsi Krishna Potta on Sep 7, 2010 9:41 AM

  • How to differentiate a packing type for Finished goods based on which customer will be invoiced ?

    I need a little expertise
    The requirement for my organization is Certain Finish goods packing.
    Currently certain, Finished goods packaging items when send to Customer, is charged for the packaging items like Pallets , Q- Bit Boxes.
    There will be a deposit fee which will appear on the customer invoice.
    Moving forward they want to eliminate that deposit fee, from the customer invoice for a few of the packaging types.. (For example Pallet we would still charge the customer the same way AS_IS today but for another pack type Q-BIT boxes customer should not be charged as a deposit fee for returing the pack type.)
    From Materials management perspective… At the time of order entry how do we differentiate a particular pack type so that for that a particular Pack type customer is not charged anything…
    2 options I am thinking is introduce a new characteristics in Classification view for PK type.. Upon entering the order the User exit will check the characteristic in material master and customer invoice won’t be charged for the Packing item if Pack type = Q Bit..
    Other one is  From the  Alternate Unit of Measure translation to Common Unit of measure / Sales Unit of measure.
    Which one would you recommend ?
    Pls advise.

    Hi Joe,
    What I was suggesting was to have different material codes per pack size. If this is done, you will not need to modify anything, other than maintain condition types for the correct material codes.
    In case you are leaning towards the classification approach, I will suggest having a custom calculation type added to include  RV64ANNN with a check of the characteristic on a custom table. In this table, maintain the pack sizes with should be charged. The logic should turn  XKOMV-KBETR = 0 if the pack size is not found in the table.

  • Output type for the managed codes cut letter is hard coded

    Hello,
    Very Good afternoon!
    I have a requirement to create new Output Types for a Smart Form.
    The already existing Output types are hard coded as shown Below :
    CONSTANTS : c_kschl_order LIKE nast-kschl
                             VALUE 'ZUS0',
                c_kschl_order1 LIKE nast-kschl
                             VALUE 'ZUS1',
    Now they do not want to use ZUS1. Insted they wnat to use New Output Types.
    u2022 Remove ZUS1 as we no longer use this one.
    u2022     Add ZAU0
    u2022     Add ZNZ0
    u2022     Add ZJP0
    u2022     Add ZCN0
    u2022     Add ZKR0
    How to add these Output types without Hardcoding as shown ABove.
    Any Suggestions will be appreciated.....
    For reference..I will paste the code of the Program here.
    Here is the code  :
                     PROGRAM DECLARATION
    PROGRAM ID           Z_RVADOR01_SALES_CUT_LETTER
    TABLES: vbak,    "Sales Document: Header Data
           vbap,    "Sales Document: Item Data
           vbpa,    "Sales Document: Partner
           vbep,    "Sales Document: Schedule Line Data
           kna1,    "General Data in Customer Master
           MARA,    "Material Master
            KOMK,                          "Communicationarea for conditions
            KOMP,                          "Communicationarea for conditions
            KOMVD,                         "Communicationarea for conditions
            VBCO3,                         "Communicationarea for view
            VBDKA,                         "Headerview
            VBDPA,                         "Itemview
            VBDPAU,                        "Subitemnumbers
            CONF_OUT,                      "Configuration data
            SADR,                          "Addresses
            TVAG,                          "Reason for rejection
            VEDKA,                         "Servicecontract head data
            VEDPA,                         "Servicecontract position data
            VEDKN,                         "Servicecontract head notice data
            VEDPN,                         "Servicecontract pos. notice data
            RISERLS,                       "Serialnumbers
            KOMSER,                        "Serialnumbers for print
            TVBUR,                         "Sales office
            TVKO,                          "Sales organisation
            ADRS,                          "Communicationarea for Address
            FPLTDR,                        "billing schedules
            WTAD_ADDIS_IN_SO_PRINT,        "additional
            WTAD_BUYING_PRINT_EXTRA_TEXT,  "texts belonging to additional
            adrc,
            adr6,
            t247.
    INCLUDE RVADTABL.
    INCLUDE RVDIREKT.
    INCLUDE VEDADATA.
    data for access to central address maintenance
    INCLUDE SDZAVDAT.
    TYPE-POOLS: ADDI.
    DATA PRICE_PRINT_MODE(1) TYPE C.       "Print-mode
    DATA: RETCODE   LIKE SY-SUBRC.         "Returncode
    DATA: REPEAT(1) TYPE C.
    DATA: XSCREEN(1) TYPE C.               "Output on printer or screen
    DATA: BEGIN OF STEU,                   "Controldata for output
            VDKEX(1) TYPE C,
            VDPEX(1) TYPE C,
            KBKEX(1) TYPE C,
            KBPEX(1) TYPE C,
          END OF STEU.
    DATA: BEGIN OF TVBDPA OCCURS 0.        "Internal table for items
            INCLUDE STRUCTURE VBDPA.
    DATA: END OF TVBDPA.
    DATA: BEGIN OF TKOMV OCCURS 50.
            INCLUDE STRUCTURE KOMV.
    DATA: END OF TKOMV.
    DATA: BEGIN OF TKOMVD OCCURS 50.
            INCLUDE STRUCTURE KOMVD.
    DATA: END OF TKOMVD.
    DATA: BEGIN OF TVBDPAU OCCURS 5.
            INCLUDE STRUCTURE VBDPAU.
    DATA: END   OF TVBDPAU.
    DATA: BEGIN OF TKOMCON OCCURS 50.
            INCLUDE STRUCTURE CONF_OUT.
    DATA: END   OF TKOMCON.
    DATA: BEGIN OF TKOMSERVH OCCURS 1.
            INCLUDE STRUCTURE VEDKA.
    DATA: END   OF TKOMSERVH.
    DATA: BEGIN OF TKOMSERVP OCCURS 5.
            INCLUDE STRUCTURE VEDPA.
    DATA: END   OF TKOMSERVP.
    DATA: BEGIN OF TKOMSERVHN OCCURS 5.
            INCLUDE STRUCTURE VEDKN.
    DATA: END   OF TKOMSERVHN.
    DATA: BEGIN OF TKOMSERVPN OCCURS 5.
            INCLUDE STRUCTURE VEDPN.
    DATA: END   OF TKOMSERVPN.
    DATA: BEGIN OF TKOMSER OCCURS 5.
            INCLUDE STRUCTURE RISERLS.
    DATA: END   OF TKOMSER.
    DATA: BEGIN OF TKOMSER_PRINT OCCURS 5.
            INCLUDE STRUCTURE KOMSER.
    DATA: END   OF TKOMSER_PRINT.
    DATA: BEGIN OF TFPLTDR OCCURS 5.
            INCLUDE STRUCTURE FPLTDR.
    DATA: END   OF TFPLTDR.
    DATA: TADDI_PRINT TYPE ADDI_SO_PRINT_ITAB WITH HEADER LINE.
    TYPES:BEGIN OF ty_orders ,
         xblnr    LIKE  mkpf-xblnr,       "delivery number
         erfmg    LIKE  mseg-erfmg,       "goods issue quantity
         custname LIKE  kna1-name1,       "customer name
         bstnk    LIKE  vbak-bstnk,       "purchase order number
         ean11    LIKE  vbap-ean11,       "upc
         kdmat    LIKE  vbap-kdmat,       "customer material code
         arktx    LIKE  vbap-arktx,       "description
         csrno    LIKE  kna1-kunnr,       "customer service rep number
         spras    LIKE  kna1-spras,       "customer language key
         csrname  LIKE  kna1-name1,       "customer service rep name
         csremail LIKE  adr6-smtp_addr,   "csr email
         csrphone LIKE  kna1-telf1,       "csr telephone
         csrext   LIKE  adrc-tel_extens,  "csr extension
         csrfax   LIKE  kna1-telfx,       "csr fax
         total    LIKE  lips-lfimg,       "cut quantity
         ldate(18)    TYPE c,
       END OF ty_orders.
    CONSTANTS: c_kschl_order LIKE nast-kschl
                             VALUE 'ZUS0',
                c_kschl_order1 LIKE nast-kschl
                             VALUE 'ZUS1',            c_parvw_shipto LIKE vbpa-parvw
                             VALUE 'WE',
                c_parvw_csr    LIKE vbpa-parvw
                             VALUE 'ZS',
                 c_eng(1)       TYPE c VALUE 'E',
                 c_sep(1)       TYPE c VALUE '/',
                 c_sale(25) type c VALUE 'Sales Order'.
    DATA: WA_VBAK TYPE VBAK,
          tbl_ord TYPE ty_orders OCCURS 0 WITH HEADER LINE,
          w_csrname(30)  TYPE c,
         w_csrno(30)    TYPE c,
         w_email    LIKE adr6-smtp_addr,
         f_shipto_found     TYPE c,
         w_custname(30) TYPE c,
         w_month(2),
         w_ldate(18),
         w_total LIKE lips-lfimg,
         w_lines        TYPE i VALUE 0,
         f_mail(1)  TYPE c,
         cnt_1          TYPE i VALUE 0,
         cnt_2          TYPE i VALUE 0,
         tbl_otf     LIKE itcoo OCCURS 0 WITH HEADER LINE,
         w_type(25)     TYPE c,
         st_doc_data   LIKE sodocchgi1,
         tbl_objtxt    LIKE solisti1 OCCURS 10 WITH HEADER LINE,
         tbl_line      LIKE tline OCCURS 0 WITH HEADER LINE,
         tbl_attach    LIKE solisti1 OCCURS 10 WITH HEADER LINE,
         tbl_objhead   LIKE solisti1 OCCURS 10 WITH HEADER LINE,
         tbl_proc_para LIKE soparai1 OCCURS 10 WITH HEADER LINE,
         tbl_maillist  LIKE somlreci1 OCCURS 10 WITH HEADER LINE,
         tbl_pack_list LIKE sopcklsti1 OCCURS 10 WITH HEADER LINE,
         tbl_cpo      LIKE itcpo OCCURS 0 WITH HEADER LINE,"SAPscript output
                                                                " interface
         tbl_cpp LIKE itcpp OCCURS 0 WITH HEADER LINE,"SAPscript output
                                                       " parameters
         tbl_smtp  TYPE szadr_adsmtp_line OCCURS 0 WITH HEADER LINE,
         tbl_cdhdpos LIKE cdshw OCCURS 0 WITH HEADER LINE,
         tbl_cdpos LIKE cdshw OCCURS 0 WITH HEADER LINE,
         wrk_lines LIKE sy-tabix,
         hltlines   TYPE i,
         off1       TYPE p,
         fle1(2)    TYPE p,
         fle2(2)    TYPE p,
         htabix     LIKE sy-tabix,
         hfeld(500) TYPE c.
    FORM ENTRY USING RETURN_CODE US_SCREEN.
    if sy-tcode = 'VA01'.
      IF nast-kschl = c_kschl_order.
      SELECT SINGLE * FROM VBAK INTO WA_VBAK WHERE vbeln = nast-objky.
      IF SY-SUBRC = 0.
      CLEAR RETCODE.
      XSCREEN = US_SCREEN.
      PERFORM PROCESSING USING us_screen.
      IF RETCODE NE 0.
        RETURN_CODE = 1.
      ELSE.
        RETURN_CODE = 0.
      ENDIF.
       ELSE.
          retcode = sy-subrc.
          syst-msgid = 'ZVERROR'.
          syst-msgno = '000'.
          syst-msgty = 'E'.
          syst-msgv1 = NAST-KSCHL.
         syst-msgv1 = 'Sales Order cut letter
                       for this order already issued'.
         syst-msgv2 = ' '.
          PERFORM protocol_update.
        ENDIF.
    ELSE.
        CLEAR retcode.
        xscreen = us_screen.
        PERFORM processing USING us_screen.
        IF retcode NE 0.
          return_code = 1.
        ELSE.
          return_code = 0.
        ENDIF.
      ENDIF.
    endif.
    ENDFORM.
          FORM PROCESSING                                               *
    FORM PROCESSING USING proc_screen.
    CASE nast-kschl.
        WHEN c_kschl_order.
          PERFORM get_orders.
          CHECK retcode = 0.
          PERFORM openform USING proc_screen vbak-landtx.
          CHECK retcode = 0.
          PERFORM layout.
          CHECK retcode = 0.
          CHECK proc_screen NE 'X'.
          w_type = c_sale.
          PERFORM send_email USING proc_screen.
      WHEN c_kschl_order1.
         PERFORM get_orders.
         CHECK retcode = 0.
         CHECK proc_screen NE 'X'.
         w_type = c_sale.
         PERFORM send_email USING proc_screen.
       WHEN OTHERS.
          retcode = 1.
          syst-msgid = 'E0'.
          syst-msgno = '430'.
          syst-msgty = 'E'.
          PERFORM protocol_update.
      ENDCASE.
      IF retcode EQ 0.
        syst-msgid = '69'.
        syst-msgno = '254'.
        syst-msgty = 'S'.
        syst-msgv1 = nast-kschl.
        PERFORM protocol_update.
      ELSE.
        syst-msgid = 'CKCC'.
        syst-msgno = '036'.
        syst-msgty = 'E'.
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.
          FORM PROTOCOL_UPDATE                                          *
          The messages are collected for the processing protocol.       *
    FORM PROTOCOL_UPDATE.
      IF xscreen EQ space.
        CALL FUNCTION 'NAST_PROTOCOL_UPDATE'
           EXPORTING
                MSG_ARBGB = SYST-MSGID
                MSG_NR    = SYST-MSGNO
                MSG_TY    = SYST-MSGTY
                MSG_V1    = SYST-MSGV1
                MSG_V2    = SYST-MSGV2
                MSG_V3    = SYST-MSGV3
                MSG_V4    = SYST-MSGV4
           EXCEPTIONS
                OTHERS    = 1.
       ELSE.
        MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
                WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
       ENDIF.
    ENDFORM.
    *&      Form  get_orders
          text
    -->  p1        text
    <--  p2        text
    FORM get_orders.
    DATA : f_csr_found        TYPE c.
    SELECT SINGLE vbeln vkorg vdatu bstnk kunnr
        FROM   vbak
        INTO  (vbak-vbeln,vbak-vkorg,vbak-vdatu,vbak-bstnk,vbak-kunnr)
        WHERE vbeln EQ nast-objky.
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'VN'.
        syst-msgno = '203'.
        syst-msgty = 'E'.
        syst-msgv1 = 'VBAK'.
        syst-msgv2 = sy-subrc.
        PERFORM protocol_update.
      ENDIF.
      SELECT vbeln posnr matnr pmatn arktx abgru kdmat werks
      FROM vbap
      INTO (vbap-vbeln,vbap-posnr,vbap-matnr,vbap-pmatn,
    vbap-arktx,vbap-abgru,vbap-kdmat,vbap-werks)
      WHERE vbeln = vbak-vbeln
      AND abgru NE space "select items havng Rejection Reason
      and PSTYV NE 'ZHDR'.
    to check whether the reason for rejection was picked from the
    managed codes tables
    data: war_abgru type abgru,
          w_exist type c.
    clear : war_abgru, w_exist.
      select single abgru  from ZMAT_REJ002
                    into war_abgru
                    where vkorg = vbak-vkorg
                    and kunnr <> vbak-kunnr
                    and MATNR = vbap-matnr
                    and datef <= vbak-vdatu
                    and datet >= vbak-vdatu.
       if sy-subrc <> 0.
             select single abgru from ZMAT_REJ003
                              into war_abgru
                              where vkorg = vbak-vkorg
                              and kunnr <> vbak-kunnr
                              and MATNR = vbap-matnr
                              and datef <= vbak-vdatu
                              and datet >= vbak-vdatu.
             if sy-subrc <> 0.
                    select single abgru from ZMAT_REJ001
                              into war_abgru
                              where vkorg = vbak-vkorg
                              and werks <> vbap-werks
                              and matnr = vbap-matnr
                              and datef <= vbak-vdatu
                              and datet >= vbak-vdatu.
                    if sy-subrc <> 0.
                         select single abgru from ZMAT_REJ004
                                             into war_abgru
                                             where vkorg = vbak-vkorg
                                             and matnr = vbap-matnr
                                             and datef >= vbak-vdatu
                                             and datet <= vbak-vdatu.
                         if sy-subrc <> 0.
                         else.
                         w_exist = 'X'.
                         endif.
                   else.
                   w_exist = 'X'.
                   endif.
             else.
             w_exist = 'X'.
             endif.
       else.
       w_exist = 'X'.
       endif.
    if w_exist = 'X'.
    end for check from managed codes table
    *to find the quantity fields
        SELECT SINGLE wmeng bmeng
        FROM vbep
        INTO (vbep-wmeng,vbep-bmeng)
        WHERE vbeln EQ vbap-vbeln
        AND   posnr EQ vbap-posnr.
    *to get info about the customer
        SELECT SINGLE kunnr
        FROM vbpa
        INTO vbpa-kunnr
        WHERE  vbeln EQ vbak-vbeln
        AND    parvw EQ c_parvw_shipto.
         IF sy-subrc EQ 0.
          f_shipto_found = 'X'.
          SELECT SINGLE name1 spras
            FROM kna1
            INTO (kna1-name1,kna1-spras)
            WHERE kunnr EQ vbpa-kunnr.
          IF sy-subrc EQ 0.
            w_custname = kna1-name1.
            CLEAR kna1-name1.
          ENDIF.
         ENDIF.
         SELECT SINGLE kunnr
        FROM vbpa
        INTO vbpa-kunnr
        WHERE vbeln EQ vbak-vbeln
        AND   parvw EQ c_parvw_csr.
        IF SY-SUBRC EQ 0.
         f_csr_found = 'X'.
          SELECT SINGLE kunnr name1 name2 adrnr
           FROM kna1
           INTO (kna1-kunnr,kna1-name1,kna1-name2,
                 kna1-adrnr)
           WHERE  kunnr EQ vbpa-kunnr.
          IF sy-subrc EQ 0.
            w_csrno = kna1-kunnr.
            w_csrname = kna1-name1.
            CLEAR kna1-name1.
               SELECT SINGLE tel_number tel_extens fax_number
                 FROM adrc
                 INTO (adrc-tel_number,adrc-tel_extens,
       adrc-fax_number)
                 WHERE addrnumber EQ kna1-adrnr.
            CLEAR: adr6, w_email.
            SELECT SINGLE * FROM adr6 WHERE addrnumber = kna1-adrnr.
            IF sy-subrc = 0.
              w_email = adr6-smtp_addr.
            ENDIF.
          ENDIF.
        ENDIF.
    *to get the date format in french
        IF kna1-spras NE c_eng.
          w_month = sy-datum+4(2).
          SELECT SINGLE ltx
            FROM t247
            INTO t247-ltx
            WHERE spras EQ kna1-spras
            AND mnr EQ w_month.
          CONCATENATE sy-datum+6(2)
                      t247-ltx
                      sy-datum+0(4)
                      INTO w_ldate
                      SEPARATED BY space.
          ELSE.
          CONCATENATE sy-datum+4(2)
                      sy-datum+6(2)
                      sy-datum+0(4)
                      INTO w_ldate
                      SEPARATED BY c_sep.
        ENDIF.
        w_total = vbep-wmeng - vbep-bmeng.
         IF w_total GT 0.
         PERFORM fill_orders.
        ELSE.
          IF vbap-abgru NE space.
            w_total = vbep-wmeng.
            PERFORM fill_orders.
          ENDIF.
        ENDIF.
        CLEAR vbap.
        endif.           " check for w_exist for Managed Codes entry
    ENDSELECT.
    IF tbl_ord[] IS INITIAL.
        retcode = 1.
        syst-msgid = 'FZ'.
        syst-msgno = '027'.
        syst-msgty = 'E'.
        PERFORM protocol_update.
      ENDIF.
      IF f_csr_found IS INITIAL.
        syst-msgid = '8B'.
        syst-msgno = '127'.
        syst-msgty = 'W'.
        syst-msgv1 = c_parvw_csr.
        PERFORM protocol_update.
      ENDIF.
      IF f_shipto_found IS INITIAL.
        syst-msgid = '8B'.
        syst-msgno = '127'.
        syst-msgty = 'W'.
        syst-msgv1 = c_parvw_shipto.
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.                    " get_orders
    *&      Form  layout
          text
    -->  p1        text
    <--  p2        text
    FORM layout.
    SORT tbl_ord BY bstnk kdmat.
      LOOP AT tbl_ord.
        AT FIRST.
          PERFORM writeform_text.
        ENDAT.
        PERFORM writeform.
        AT LAST.
          PERFORM writeform_footer.
        ENDAT.
      ENDLOOP.
      CLEAR : cnt_1,cnt_2.
      PERFORM closeform.
    ENDFORM.                    " layout
    *&      Form  openform
          text
    FORM openform USING us_screen us_country.
    DESCRIBE TABLE tbl_ord LINES w_lines.
      IF w_lines EQ 0.
        retcode    = '1'.
        syst-msgid = 'FE'.
        syst-msgno = '078'.
        syst-msgty = 'E'.
        PERFORM protocol_update.
      ENDIF.
      CHECK retcode EQ 0.
    INCLUDE zrvadopfo.
    ENDFORM.                    " openform
    *&      Form  send_email
          text
         -->P_PROC_SCREEN  text
    FORM send_email USING    PROC_SCREEN.
    f_mail = 'X'.
      PERFORM openform USING proc_screen vbak-landtx.
      LOOP AT tbl_ord.
        AT FIRST.
          PERFORM writeform_text.
        ENDAT.
        PERFORM writeform.
        AT LAST.
          PERFORM writeform_footer.
        ENDAT.
      ENDLOOP.
      CLEAR cnt_2.
      PERFORM closeform.
      CALL FUNCTION 'CONVERT_OTF'
           EXPORTING
                format                = 'PDF'  "'ASCII'
           IMPORTING
                bin_filesize          = st_doc_data-doc_size
           TABLES
                otf                   = tbl_otf
                lines                 = tbl_line
           EXCEPTIONS                                           "DEVK912166
                err_max_linewidth     = 1
                err_format            = 2
                err_conv_not_possible = 3
                OTHERS                = 4.
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'OA'.                                      "DEVK912166
        syst-msgno = '186'.                                     "DEVK912166
        syst-msgty = 'E'.                                       "DEVK912166
        PERFORM protocol_update.
      ENDIF.
      REFRESH tbl_objtxt.
      CLEAR tbl_objtxt.
      CLEAR tbl_proc_para.
      REFRESH tbl_proc_para.
      CLEAR tbl_maillist.
      REFRESH tbl_maillist.
      CLEAR tbl_pack_list.
      REFRESH tbl_pack_list.
      st_doc_data-obj_name   = 'Sales Order Cut Letter'.
      st_doc_data-obj_langu   = 'E'.                            "DEVK905849
      st_doc_data-sensitivty  = 'F'.                            "DEVK905849
      st_doc_data-obj_prio    =  1.                             "DEVK905849
      CONCATENATE w_type 'Cut Letter' INTO          "#EC NOTEXT
                                  st_doc_data-obj_descr  SEPARATED BY space.
      DATA w_line(3) TYPE c.
      PERFORM format_pdf.                                       "DEVK905849
      concatenate VBAK-VBELN '.PDF' into tbl_objhead.
    tbl_objhead = 'Sales Order Cut Letter.PDF'.
      APPEND tbl_objhead.
           "DEVK905849
      CLEAR wrk_lines.
      DESCRIBE TABLE tbl_attach LINES wrk_lines.
    fields needed for email
      tbl_maillist-com_type = 'INT'.
      tbl_maillist-receiver =  w_email.
      tbl_maillist-rec_type = 'U'.
      APPEND tbl_maillist.
    send email
      CALL FUNCTION 'SO_NEW_DOCUMENT_SEND_API1'
                                      STARTING NEW TASK 'MAIL'
           EXPORTING
                document_data              = st_doc_data
                document_type              = 'PDF'
                COMMIT_WORK                = 'X'    " added after ECC6.0 upgrade
           TABLES
                object_header              = tbl_objhead
                object_content             = tbl_objtxt
                receivers                  = tbl_maillist
           EXCEPTIONS                                           "DEVK912166
                too_many_receivers         = 1
                document_not_sent          = 2
                document_type_not_exist    = 3
                operation_no_authorization = 4
                parameter_error            = 5
                x_error                    = 6
                enqueue_error              = 7
                OTHERS                     = 8
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'ZA_G'.                                    "DEVK912166
        syst-msgno = '922'.                                     "DEVK912166
        syst-msgty = 'E'.                                       "DEVK912166
        syst-msgv1 = sy-subrc.                                  "DEVK912166
        syst-msgv2 = tbl_smtp-adsmtp-smtp_addr.                 "DEVK912166
        PERFORM protocol_update.
        syst-msgid = 'VW'.
        syst-msgno = '001'.
        syst-msgty = 'E'.
        syst-msgv1 = 'Print successful:email Recepient Invalid'."#EC NOTEXT
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.                    " send_email
    *&      Form  fill_orders
          text
    -->  p1        text
    <--  p2        text
    FORM fill_orders.
    tbl_ord-bstnk    = vbak-bstnk.
      tbl_ord-kdmat    = vbap-kdmat.
      tbl_ord-xblnr    = vbak-vbeln.
      tbl_ord-ean11    = vbap-pmatn.
      tbl_ord-arktx    = vbap-arktx.
      tbl_ord-csrno    = w_csrno .
      tbl_ord-csremail = w_email.
      tbl_ord-spras    = kna1-spras .
      tbl_ord-csrphone = adrc-tel_number.
      tbl_ord-csrfax   = adrc-fax_number.
      tbl_ord-csrext   = adrc-tel_extens.
      tbl_ord-total    = w_total.
      tbl_ord-custname = w_custname.
      tbl_ord-csrname  = w_csrname .
      tbl_ord-ldate    = w_ldate.
      APPEND tbl_ord.
      CLEAR tbl_ord.
      CLEAR w_total.
      CLEAR w_ldate.
    ENDFORM.                    " fill_orders
    *&      Form  writeform_text
          text
    -->  p1        text
    <--  p2        text
    FORM writeform_text.
    CALL FUNCTION 'WRITE_FORM'
           EXPORTING
                element = 'WTEXT'
                window  = 'WINDOW2'
           EXCEPTIONS
                element = 1
                window  = 2.
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'EBR'.
        syst-msgno = '056'.
        syst-msgty = 'E'.
        syst-msgv1 = 'WTEXT'.
        syst-msgv2 = 'WINDOW2'.
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.                    " writeform_text
    *&      Form  writeform
          text
    -->  p1        text
    <--  p2        text
    FORM writeform.
    CALL FUNCTION 'WRITE_FORM'
           EXPORTING
                element = 'EMAIN'
                window  = 'MAIN'
           EXCEPTIONS
                element = 1
                window  = 2.
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'EBR'.
        syst-msgno = '056'.
        syst-msgty = 'E'.
        syst-msgv1 = 'WTEXT'.
        syst-msgv2 = 'WINDOW2'.
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.                    " writeform
    *&      Form  writeform_footer
          text
    -->  p1        text
    <--  p2        text
    FORM writeform_footer.
    IF nast-spras = 'N'.
        CALL FUNCTION 'WRITE_FORM'
             EXPORTING
                  element = 'FOOTER'
                  window  = 'MAIN'
             EXCEPTIONS
                  element = 1
                  window  = 2.
      ENDIF.
      CALL FUNCTION 'WRITE_FORM'
           EXPORTING
                element = 'WFOOTER'
                window  = 'WINDOW12'
           EXCEPTIONS
                element = 1
                window  = 2.
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'EBR'.
        syst-msgno = '056'.
        syst-msgty = 'E'.
        syst-msgv1 = 'WFOOTER'.
        syst-msgv2 = 'WINDOW12'.
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.                    " writeform_footer
    *&      Form  closeform
          text
    -->  p1        text
    <--  p2        text
    FORM closeform.
    CALL FUNCTION 'CLOSE_FORM'
           TABLES
                otfdata                  = tbl_otf
           EXCEPTIONS
                unopened                 = 1
                bad_pageformat_for_print = 2
                OTHERS                   = 3.
      IF sy-subrc NE 0.
        retcode = sy-subrc.
        syst-msgid = 'PS'.
        syst-msgno = '005'.
        syst-msgty = 'E'.
        PERFORM protocol_update.
      ENDIF.
    ENDFORM.                    " closeform
    *&      Form  format_pdf
          text
    -->  p1        text
    <--  p2        text
    FORM format_pdf.
    FIELD-SYMBOLS <fs>.
      DESCRIBE TABLE tbl_line    LINES  hltlines.
    DESCRIBE FIELD tbl_line    LENGTH fle1 IN BYTE MODE . Defect#1579-
    DESCRIBE FIELD tbl_objtxt  LENGTH fle2 IN BYTE MODE . Defect#1579-
    Start of Defect#1579+
      DESCRIBE FIELD tbl_line    LENGTH fle1 IN CHARACTER MODE.
      DESCRIBE FIELD tbl_objtxt  LENGTH fle2 IN CHARACTER MODE.
    End of Defect#1579+
      CLEAR   tbl_objtxt.
      REFRESH tbl_objtxt.
      LOOP AT tbl_line.
        htabix = sy-tabix.
        MOVE tbl_line TO hfeld+off1.
        IF htabix = hltlines.
          fle1 = strlen( tbl_line ).
        ENDIF.
        off1 = off1 + fle1.
        IF off1 GE fle2.
          CLEAR tbl_objtxt.
          tbl_objtxt = hfeld(fle2).
          APPEND tbl_objtxt.
          SHIFT hfeld BY fle2 PLACES.
          off1 = off1 - fle2.
        ENDIF.
        IF htabix = hltlines.
          IF off1 GT 0.
            CLEAR tbl_objtxt.
            tbl_objtxt = hfeld(off1).
            APPEND tbl_objtxt.
          ENDIF.
        ENDIF.
      ENDLOOP.
    ENDFORM.                    " format_pdf
    ANy Suggestion or help will be appreciated!
    Regards,
    Kittu
    Edited by: Kittu on Jun 30, 2008 12:32 PM

    Hello Julie Waller,
    Very Good evening!
    Thank you very much for your response!
    Sometimes...I miss the basic things and start concentarcting on typical ways to fix the issue. ....which will only make my issue critical. 
    Hello Sathya,
    Thank you for your response!
    POints are rewarded..
    Have a great day ahead!
    Regards,
    Kittu

  • How to change exchange rate type for specific pricing condition type

    Hello every one,
    I have a requirement for billing ie VF01.
    currently  all the exchange rate are being calculated with exchange rate type 'M' by default.
    but now client want it should calculate exchange rate with type 'E' for two pricing condition type for all others it should calculate with type 'M'
    Please any body can help me with the exit and code which i can use.
    I have checked exits SDVFX008.
    but how to change exchange rate with type 'E' only for two conditions.
    as changing exchange rate at document header will change exchange rate for all condition type.

    You need to assign KOMK-KURST = 'E', for those two condition types. If it had been item number specific, you could have used USEREXIT_PRICING_PREPARE_TKOMK(RV60AFZZ).
    Do one thing, put a breakpoint on FM 'PRICING' and then do selective runtime analysis.
    Check whether any user exit/BADI/ explicit enhancement are available when condition types are processed in a loop. If nothing is available, try implicit enhancement.
    Link to refer for selective runtime analysis - Runtime Analysis for VOFM
    Also try with VOFM requirements ( not sure whether changing KOMK-KURST is permissable in requirement as normally  we only set sy-subrc values to suppress/allow condition types ). Don't forget to assign requirements against condition types in pricing procedure.

  • Ref.mov.type for WM

    I am getting an error message 'Error while determining ref.mov.type for WM via Table 156S: 101/ / / /B/X/ ' while creating inbound delivery. Is anyone acquainted with such an issue? Can you please advice?
    I have checked all the config for movement type definations. Everything looks ok. Please let me know if there is a fix.
    Thanks!

    Hi Avi,
    I think, you didn't get me ...
    In the above configuration what I explained, all you need to do is just adding the ref mvt type the one that is missing...it must be currently blank because of which the error what you posted is appearing.  All that you need to do is just add the ref mvt type for the line as explained....
    Remaining checkboxes, indicators etc....you are not even expected to be able to change....
    What it means?  for mvt type 101 of IM, when a material related transaction GR posting happens, for the material type used for setting up the material, in the plant of your concern, when there is no value and qty update is active in material type config, and which is not of special stock related posting, but referencing B - Purchase Order, of Transfer Type ie, stock transfer PO, the corresponding Ref Mvt type required to process further in WM, is missing in IM mvt type assignment (T156)...
    Regards
    Regards

  • FSCM-CR Case types for Documented Credit Decision (FDCD, FDCA) missing.

    Hi FSCM community
    I am looking at the FSCM CR module and got some issues here and there.
    Here's one of them.
    Documentation for the SAP IMG node:
    FSCM -> Credit Management -> Credit Risk Monitoring -> Documented Credit Decision -> Settings in the Case Management Component
    'Case types
    The following case types are contained in the standard system for SAP Credit Management: Credit Limit Request (F_CR), Doc. Credit Decision for Document (FDCD), Doc. Credit Decision for the Account (FDCA)'
    1. Were you able to find the FDCD or FDCA case types in your systems?
    Mine only has F_CR.
    2. What are the:
    - Processes
    - RMS ID's
    - Case record models
    assigned to FDCD or FDCA?
    3. Are they any different from the F_CR?
    4. I understand they're required so that they may be assigned as Documented Credit decisions (under Define Case Types for Documented Credit Decision). What Case Types did you assign?
    My SAP_APPL is 617, so it's rather up to date.
    thanks for all your input,
    Darek

    Hi Ankur,
    I found the BC set, reviewing the content.
    It seems like you saved my day
    I don't see any other UKM* related BC sets except for the one you mentioned.
    Do you know of any others?
    regards,
    Darek

  • Creation of new document types for document splitting rules

    Hi experts,
    We have copied from existing SA  document type to new document type.
    In standard SAP  SA  document type - define document splitting rule, we have select  "NO INHERITANCE OF ACCOUNT ASSINGNMENT", when posting the  GL document SA  document type without mapping partner profit center,system is control the derive the partner profit center.
      Our requirement is  copied from existing  SA  document type to create a new document type - we have created the new dusiness transaction variant and we have map the "classify document type to document splitting rule " and we have selet the "No inheritance of account assignment" while posting in FB01 GL document with out mapping partner profit center system is not control the " derive partner profit center".
    Could you please assist us as soon as possible
    Thanks ,
    Sreenivas
    Edited by: sapfico.srini12 on Jan 16, 2012 4:37 PM

    Hi,
    In order to create a document type for a purchase requisition  use the path
    spro-materials management - purchasing--purchase requisitions --define  document type
    in that screen you select the document type you want to copy to create your document type and perform the action.
    if you want to change the screen/field selection for your document type select the field selection key (if you select the document type as NBB the field selection key will be NBB.,and go to the screen and change the field status.
    Hope this will be suffient for your requirement.
    Regards,
    Raghu.

Maybe you are looking for

  • Cut off process for Open Purchase Orders

    Dear friends We are preparing for Go Live. i want to know what are the steps required in Cut off activities with respect to Open POs. E.g if there is a PO for 1000 units against which GRN has been done for 200 units and Invoicing has been done for 10

  • Is there any function to change the width of forms'graphic ?

    Hi All, Is there any function to change the width of forms'graphic ? May be like set***property. Thanks, ke xiong

  • Data exchange between 2 CRMs

    Hi expert: I want to download biz data(BP/material/sales order)  from CRM1 to CRM2.  Both of them are CRM 7.0. Both of them have connections to one ECC. I have some settings for this proposals(eg. BUPA_MAIN): CRM2<-->ECC is ok CRM1<ECC is ok, but CRM

  • 6310 all-in-one won't print!!!!

    6310 all-in-one will not print--after reload of driver...driver is up to date---still won't print!!!

  • "Could not Load file or assembly..." Another one

    I have searched in the forum for possibles solutions and i can't fix this problem yet. The problem comes when i decided to use my c# assemblies without installing them in the GAC. The sequence calls a "Tool" class that include a "Reader" class, that