ReSampling? Hot Swapping? What do these terms mean?

After years of digital audio I still run into terms that don't really mean anything specific to me.
Could someone shed some light on what these two things refer to?
Thanks a bunch!

eMagnus wrote:
After years of digital audio I still run into terms that don't really mean anything specific to me.
Could someone shed some light on what these two things refer to?
Thanks a bunch!
"Sampling" refers to those extravagant food fairs where you can stroll about and sample cuisine from different countries.
And Hot Swapping... that's for swingers only!
Very loose explanations follow.
Sampling.... the act of digitally recording a sound source or part of a sound source for use as either an instrument or effect. Drum libraries like Addictive Drums or some of the kits/instruments included with Logic are "sampled".
Recording each part of a real drum set (or -any- instrument) and then building an instrument out of it is sampling. You can even sample samples..
Hot Swapping has to do with plugging/unplugging USB or Firewire devices while the computer/device is still on. Hot swappable devices are supposed to be recognized by the host machine when plugged in.
pancenter-

Similar Messages

Sync - merge - what EXACTLY do these terms mean?

Howdy. I recently plunged into the iPhone world & I'm LOVING IT!!!!!!
So, what exactly does SYNC & MERGE mean? what will be the final results?
with my iPod shuffle, I'm able to "auto fill" from a folder of pre-selected podcasts in iTunes. After listening to the iPod for awhile, I reconnect the iPod to iTunes (on the computer) & the podcasts in iTunes are updated as with actions taken on the iPod. for example, iTunes on the computer will indicate wether or not I listened to these particular podcasts on the iPod or not, & will also remember where I left off. So it seems that the iPod updates iTunes on the computer.
But, ... this does NOT seem to be the same with the iPhone. It seems like when I plug in my iPhone to the computer & "sync", iTunes isn't updated as to what I already watched on the iPhone, like the iPod did. In order to update iTunes with what i already watched on the iPhone, I need to manually delete the vidcasts from the iTunes on the computer, which seems like a step back from my little iPod shuffle.
ALSO: if I change contact information on my iPhone, will this updated info be lost when I connect the iPhone to the Computer?
So what exactly does SYNC & MERG mean?
It seems that the iPhone reacts differently for different media. I'm very confused & I wish there was a place to understand all this without the generic "sync" word being used without explanation. does sync mean replace, update, ... ????
I've been searching around the net for this info for awhile, but all I find is these terms, without sufficient information as to what exactly MERGE & SYNC actually do.
Can someone suggest some place that explains this in the detail I'm looking for?
Thanks so much.
Jesse Luke

Under the Podcasts tab for your iPhone sync preferences, there are various options. I have sync all unplayed episodes of selected podcasts to be transferred to my iPhone. If I listen to an podcast on my iPhone in it's entirety, the podcast will be removed from my iPhone when syncing with iTunes.
The iPhone includes a sync process - some of the data included with the sync process is a one way transfer process only from your computer to your iPhone such as iTunes music, and the same for selected photos to be transferred from your computer to your iPhone.
The sync process for contact info, calendar events, and Safari bookmarks with the supported applications on your computer is a bidirectional or true sync process. When syncing an iPhone for contact info the first time with a supported application on your computer that includes contact info, you will be provided a merge prompt if your iPhone includes any contact info that was manually entered in your iPhone's address book. This will merge the contact info between the two. After the first sync or merge for this data, it will be a bidirectional or true sync process. Change info for a contact on your iPhone, and the info will be changed for the contact info with the supported address book on your computer when followed by a sync, and vice-versa. Add a new contact with the supported address book on your computer, and the new contact will be transferred to your iPhone's address book during the next sync, and vice versa. The same applies to calendar events when syncing with a supported calendar app on your computer.

What does these messages mean

I cannot get into my itunes because this message comes up. "A required iTunes component is not installed. Please repair or reinstall iTunes. (42404) "
Then when I exit this message another one comes up. We could not complete your iTunes store request. "an unknown error occured (50)"
Please help me to fix this.
Grandmakat70

zodmaner wrote:
Hi, well today when starting up my box I noticed these two startup messages:
:: Initiate Random Seed
:: Removing LeftOver files
What does these mean? And what program/service runs it? (And what 'left over files' is it removing?) I think I never see them before. Is these message appears because I just install sudo?
Also when shutting down there is also a message concerning a Random Seed. (Saving Random Seed). What is it doing?
Well... if your head over to your /etc/rc.sysinit, you'll see exactly what it does. If I remember correctly, saving random seed is just saving your startup time because it is random, and removing leftover files is clearing out the /tmp/ directory.

What does Payment terms means in SD

Hello SD Experts
I am implementing a project that requires a report on payment terms of an order. This is a BW project but however, it is an SD report.
I need to know what field represents payment terms in SD tables - header or item table?
Which field also represents complete delivery indicator.
Thank you.

Hi ,
Terms of Payment is defining at the time new customer creation , it is the Key for defining payment terms composed of cash discount percentages and payment periods, It is used in sales orders, purchase orders, and invoices also.
In R/3 Header Table KNVV - Customer Master Sales Data , is containing both of your required fields, check in SE11 Transaction and give the Table name KNVV there you can see what are the technical names and the Description for all available fields.
in your case   standard fields are using than these two are your fields in KNVV Table
Terms of Payment field is               :     ZTREM
Complet delivery for each sales order   : AUTLF
Regards
Naren..

What do these errors mean ? Web Logic

I am attempting to start Web Logic Server, and Web Logic Server for my application installed on my machine. I get the following errors, completely new to web Logic so I don't know what they mean. But it seems to be a privelege issue related to the admin account. Please note that I have in no way changed any settings to my admin account recently, nor my password or anything. Everything was working fine for a week until yesterday, and I can't think of anything I have changed. Any input is appreciated. Highlighted the main errors in bold.
When starting Web Logic Server for my application:
<Nov 21, 2010 3:49:48 PM CST> <Notice> <Server> <BEA-002613> <Channel "DefaultSe
cure[1]" is now listening on 127.0.0.1:7002 for protocols iiops, t3s, ldaps, htt
ps.>
<Nov 21, 2010 3:49:48 PM CST> <Notice> <Server> <BEA-002613> <Channel "DefaultSe
cure" is now listening on 10.0.2.15:7002 for protocols iiops, t3s, ldaps, https.
>
<Nov 21, 2010 3:49:48 PM CST> <Notice> <Server> <BEA-002613> <Channel "Default[1
]" is now listening on 127.0.0.1:7001 for protocols iiop, t3, ldap, snmp, http.>
<Nov 21, 2010 3:49:48 PM CST> <Notice> <Server> <BEA-002613> <Channel "Default"
is now listening on 10.0.2.15:7001 for protocols iiop, t3, ldap, snmp, http.>
<Nov 21, 2010 3:49:48 PM CST> <Notice> <WebLogicServer> <BEA-000331> <Started We
bLogic Admin Server "examplesServer" for domain "wl_server" running in Developme
nt Mode>
<Nov 21, 2010 3:49:50 PM CST> <Notice> <WebLogicServer> <BEA-000365> <Server sta
te changed to RUNNING>
<Nov 21, 2010 3:49:50 PM CST> <Notice> <WebLogicServer> <BEA-000360> <Server sta
rted in RUNNING mode>
<Nov 21, 2010 3:50:00 PM CST> <Error> <Security> <BEA-090513> <ServerIdentity fa
iled validation, downgrading to anonymous.>
<Nov 21, 2010 3:50:01 PM CST> <Error> <Security> <BEA-090513> <ServerIdentity fa
iled validation, downgrading to anonymous.>
<Nov 21, 2010 3:50:01 PM CST> <Error> <Security> <BEA-090513> <*ServerIdentity fa*
iled validation, downgrading to anonymous.>
<Nov 21, 2010 3:50:01 PM CST> <Warning> <RMI> <BEA-080003> <RuntimeException thr
own by rmi server: weblogic.rmi.internal.AdminAccessOnlyServerRef@1f, implementa
tion: 'weblogic.server.channels.RemoteChannelServiceImpl@2332930', oid: '31', im
plementationClassName: 'weblogic.server.channels.RemoteChannelServiceImpl'
java.lang.SecurityException: Method 'getAdministrationURL' cannot be invoked wi
thout administrator access.
java.lang.SecurityException: Method 'getAdministrationURL' cannot be invoked wit
hout administrator access
at weblogic.rmi.internal.AdminAccessOnlyServerRef.getWorkManager(AdminAc
cessOnlyServerRef.java:29)
at weblogic.rmi.internal.BasicServerRef.dispatch(BasicServerRef.java:316
at weblogic.rmi.internal.BasicServerRef.dispatch(BasicServerRef.java:944
at weblogic.rjvm.RJVMImpl.dispatchRequest(RJVMImpl.java:1138)
at weblogic.rjvm.RJVMImpl.dispatch(RJVMImpl.java:1020)
Truncated. see log file for complete stacktrace
when starting Web Logic Server for my application:
<Nov 21, 2010 4:15:19 PM CST> <Notice> <WebLogicServer> <BEA-000365> <Server sta
te changed to STARTING>
<Nov 21, 2010 4:17:42 PM CST> <Error> <org.apache.beehive.netui.pageflow.interna
l.AdapterManager> <BEA-000000> <ServletContainerAdapter manager not initialized
correctly.>
<Nov 21, 2010 4:17:46 PM CST> <Notice> <Log Management> <BEA-170027> <The Server
has established connection with the Domain level Diagnostic Service successfull
y.>
<Nov 21, 2010 4:17:48 PM CST> <Notice> <WebLogicServer> <BEA-000365> <Server sta
te changed to ADMIN>
<Nov 21, 2010 4:17:48 PM CST> <Notice> <WebLogicServer> <BEA-000365> <Server sta
te changed to RESUMING>
<Nov 21, 2010 4:17:49 PM CST> <Emergency> <Security> <BEA-090087> <Server failed
to bind to the configured Admin port. The port may already be used by another p
rocess.>
<Nov 21, 2010 4:17:49 PM CST> <Error> <Server> <BEA-002606> <Unable to create a
server socket for listening on channel "Default[1]". The address 127.0.0.1 might
be incorrect or another process is using port 7001: java.net.BindException: Add
ress already in use: JVM_Bind.>
<Nov 21, 2010 4:17:49 PM CST> <Critical> <WebLogicServer> <BEA-000362> <Server f
ailed. Reason: Server failed to bind to any usable port. See preceeding log mess
age for details.>
<Nov 21, 2010 4:17:49 PM CST> <Notice> <WebLogicServer> <BEA-000365> <Server sta
te changed to FAILED>
<Nov 21, 2010 4:17:49 PM CST> <Error> <WebLogicServer> <BEA-000383> <A critical
service failed. The server will shut itself down>
<Nov 21, 2010 4:17:49 PM CST> <Error> <Server> <BEA-002606> <Unable to create a
server socket for listening on channel "Default". The address 10.0.2.15 might be
incorrect or another process is using port 7001: java.net.BindException: Addres
s already in use: JVM_Bind.>
<Nov 21, 2010 4:17:49 PM CST> <Notice> <WebLogicServer> <BEA-000365> <Server sta
te changed to FORCE_SHUTTING_DOWN>

The message weblogic.server.channels.RemoteChannelServiceImpl@2332930', oid: seems like there is some trouble
with your OID.
Another message in your loggng:
Unable to create a server socket for listening on channel "Default". The address 10.0.2.15 might be incorrect or another process is using port 7001: java.net.BindException: Address already in use: JVM_Bind.
Tells you there is already a process running on port 7001 (you can use the netstat -a command to check if the port 7001 is taken).

Firewall Log - what do these entries mean?

I am especially concerned with the XXX is listening entries. What does this mean? Are they being blocked? I access the internet through a wireless router connected to DSL with that firewall and my computer's firewall turned on. I did find the Macworld Firewall article and have changed my firewall settings to match what they say. Just curious as to who is listening and what this means.
I have replaced the computer name with ****
== Partial Log Below ======================
May 24 09:37:25 ****-computer Firewall[49]: Deny cupsd data in from 192.168.0.198:631 uid = 0 proto=17
May 24 09:37:55: --- last message repeated 1 time ---
May 24 09:44:14 ****-computer Firewall[50]: qmasterd is listening from 0.0.0.0:49152 uid = 0 proto=6
May 24 09:46:47 ****-computer Firewall[50]: krb5kdc is listening from :::88 uid = 0 proto=6
May 24 09:46:47 ****-computer Firewall[50]: krb5kdc is listening from 0.0.0.0:88 uid = 0 proto=6
May 24 09:50:52 ****-computer Firewall[50]: Deny cupsd data in from 192.168.0.198:631 uid = 0 proto=17
May 24 09:51:22: --- last message repeated 1 time ---
=== Since checking "Set access for specific services..." and "Enable Stealth Mode" the log looks like this =================
May 24 10:59:05 ****-computer Firewall[50]: Deny cupsd data in from 192.168.0.198:631 uid = 0 proto=17
May 24 10:59:35: --- last message repeated 1 time ---
May 24 11:12:03 ***s-computer Firewall[50]: Stealth Mode connection attempt to TCP 192.168.0.196:49489 from 17.254.2.136:443
May 24 11:12:33: --- last message repeated 3 times ---
Message was edited by: Tim Rogan

Just turn on WPA security on your wireless router, and use a password that is not in any dictionary, and then you can pretty much assume nobody's going to be able to join your network.
Oh, and that last IP address in your log?
May 24 11:12:03 ***s-computer Firewall50: Stealth Mode connection attempt to TCP 192.168.0.196:49489 from 17.254.2.136:443
Looked it up at arin.net and it belongs to...
Search ARIN WHOIS for: 17.254.2.136
OrgName: Apple Computer, Inc.
OrgID: APPLEC-3
Address: 20740 Valley Green Drive, MS32E
City: Cupertino
StateProv: CA
PostalCode: 95014
Country: US
NetRange: 17.0.0.0 - 17.255.255.255
CIDR: 17.0.0.0/8
NetName: APPLE-WWNET
NetHandle: NET-17-0-0-0-1
Parent:
NetType: Direct Assignment
NameServer: NSERVER.APPLE.COM
NameServer: NSERVER2.APPLE.COM
NameServer: NSERVER.EURO.APPLE.COM
NameServer: NSERVER.ASIA.APPLE.COM
Comment:
RegDate: 1990-04-16
Updated: 2000-05-23
RTechHandle: ZA42-ARIN
RTechName: Apple Computer, Inc.
RTechPhone: +1-408-974-7777
RTechEmail: [email protected]

Urgent help, what do these exceptions mean

I was wondering what it means exactly when a InternalError(Ex02),
VirtualMachineError are thrown. im designing a programme which was working fine now suddenly it is throwing those errors, and for the life of me i cant figure out why and what they mean.
Please can someone help.

It means something really bad happened inside the JVM. And unless you want to mess with the JVM source code you are unlikely to fix it, nor usually figure out exactly what caused it.
It might also be caused by your environment, like trying to run a class file created with java 1.0 on a 1.3 jvm or something like that. Not likely, but possible.
Try redesigning your code and hope it goes away.
If you can reduce the code to a very small sample you could post it here and someone might be able to provide a more specific answer and/or a work around. (You need to provide the jvm version you are running under too.)

What do these symbols mean? (FCP6)

Here are a couple of screen shots. I guess the yellow triangle with the exclamation point and the red/green lines are telling me that the white in this shot is blown out, right? What does the green circle with the checkmark mean?
Thanks!
Andy

They mean you have 'Show Excess Luma' turned on in the Canvas or Viewer windows. The exclamation point means that the luminance levels are too high - the green check mark means they are within proper limits.
-DH

What does these codees mean?

Pls help me with the meaning of the following codes,
1. int count;
for (int i = 0; i<COUNT.length; i++)
count = Integer.parseInt(COUNT);
2. if(POINT.compareTo("R") != 0)
3.if (COUNT_02.compareTo("0") != 0)
4.result.addValue(EAN_04count_EAN+3);
5.result.addValue(EAN_04count_EAN+3);
6.result.addValue(Quantitycount_qty);
Also can u suggest some urls where some documaents can be available to enhance Java skills to develop UDFs.
Points will be awarded. Pls help. I hav been assigned huge responsibilities in XI, though I am an Abaper!
PS: Can u suggest any PDF where I can come to know about the different syntax, commands as used above, so that I can develop my own java codes....
Arnab .

Hi,
1. int count;
for (int i = 0; i<count.length; i++)
count = Integer.parseInt(count);
Ans: Here Count is a variable and all the count variables should be changed to an Object.
2. if(POINT.compareTo("R") != 0)
Ans: Here POINT should be a String Constant
public int compareTo(String anotherString)
Compares two strings lexicographically. The comparison is based on the Unicode value of each character in the strings. The character sequence represented by this String object is compared lexicographically to the character sequence represented by the argument string. The result is a negative integer if this String object lexicographically precedes the argument string. The result is a positive integer if this String object lexicographically follows the argument string. The result is zero if the strings are equal; compareTo returns 0 exactly when the equals(Object) method would return true.
3. if (COUNT_02.compareTo("0") != 0)
Ans : Same as (2)
4. result.addValue(EAN_04count_EAN+3);
Ans: Here what is result ? Check for result.addValue method in Java API @ http://java.sun.com/j2se/1.5.0/docs/api/
5.result.addValue(EAN_04count_EAN+3);
Ans: Same as 4
6.result.addValue(Quantitycount_qty);
Ans: Same as 4
Regards,
Ramana Kumar. A

What do these settings mean on the 5th gen AE?

Just got my new Airport Extreme (MD031LL/A running Version 7.5.2) setup last night and being an IT guy, I'm always eager to dig into the Advanced menu options to see what tweaks and customizations my toys are capable of. There are a few questions that I have:
1. On the advanced controls, what should I set my Multicast Rate to (Low, Medium, High)? I have searched online but haven't found any good consistent answers about what this does or what the 3 settings actually change.
2. Is it necessary to check the box for "5GHz Network Name" to get the most from the 5GHz network? Some sites/forums say that allowing your 5GHz 802.11N devices to be connected to a separate network will result in faster data transfer rates on the LAN for those devices. I don't really see why that would be the case since, if the device is capable, it will connect at that level, and if not, it won't.
3. How do you configure the Syslog Destination Address? When I click on that field to enter a location I just get the "dong" error.
4. What is the WPA Group Key Timeout?

abrauda wrote:
1. On the advanced controls, what should I set my Multicast Rate to (Low, Medium, High)?
On former versions of the AP-Extreme there where real values instead of low - medium - high.
It's important for streaming media; e.g. music.
Apple: ""Multicast rate: Choose a multicast rate from the pop-up menu. If you set the
multicast rate high, only clients on the network that are within range and can achieve the speed you set will receive transmissions."" (Manual, Chapter 3, Page 23)
abrauda wrote:
2. Is it necessary to check the box for "5GHz Network Name" to get the most from the 5GHz network? Some sites/forums say that allowing your 5GHz 802.11N devices to be connected to a separate network will result in faster data transfer rates on the LAN for those devices. I don't really see why that would be the case since, if the device is capable, it will connect at that level, and if not, it won't.
It's not necessary but recommended.
If not set, the connected devices are able to switch the radio band if e.g. the signal fade, and with that use the attached BSSID of that radio band. That could lead to trouble (drop outs) e.g. if you stream music to a AP-Express.
Setting a name for the 5GHz allows you to force the 5GHz capable devices to use that connection only.
For instance, with a 2011 MBPro on the 2.4GHz 802.11n you will have a max connection speed of 150MBit/s and on 5GHz 802.11n 450MBit/s due to MiMo ( http://en.wikipedia.org/wiki/MIMO ) with a 150MBit/s for each spatial stream.
abrauda wrote:
3. How do you configure the Syslog Destination Address? When I click on that field to enter a location I just get the "dong" error.
Check "Allow SNMP" and enter the IP address of the computer that will receive the logs in the Syslog Destination Address field.
abrauda wrote:
4. What is the WPA Group Key Timeout?
it sets the frequency of encryption key rotation between the stations and the access point (Extreme). See --> http://en.wikipedia.org/wiki/CCMP
Lupunus
Message was edited by: lupunus

What do these logs mean and do I need to worry about them?

ACK! I've been having trouble with iPhoto and so went to check the logs and crash reporter for info. While there, I found a couple of alarming items: a console.log with info I don't understand and a NetworkSpyAlertErr.log, which reads:
nsapAgent: kext write Failed!
nsapAgent: init failed. kext write failed.
nsapAgent: kext write Failed!
nsapAgent: init failed. kext write failed.
nsapAgent: kext write Failed!
nsapAgent: init failed. kext write failed.
nsapAgent: kext write Failed!
nsapAgent: init failed. kext write failed.
nsapAgent: kext write Failed!
nsapAgent: init failed. kext write failed.
Um...not sure what Network Spy agent is, as it sure isn't anything that I've installed. Is this a normal part of the mac OS? When I opened the above log, console also opened with this report:
Mac OS X Version 10.4.10 (Build 8R218)
2007-10-30 11:03:54 -0600
2007-10-30 11:03:55.447 loginwindow[81] FSResolveAliasWithMountFlags returned err = -43
2007-10-30 11:03:57.574 HPEventHandler[355]: DebugAssert: Third Party Client: ((__null) != m_lock && 0 == (*__error())) Can't create semaphore lock [/Volumes/Development/Projects/HP/mac-software/mac-software/core/HPEventHandler /Sources/HPTMNotificationManager.cpp:60]
2007-10-30 11:04:11.514 MagicMenuHotKeyDaemon[363] Started
Child: Can't read length for data
Created child to sync device with pid 373...
Waiter has started running...
Waiter is done running
Sending final status from child helper tool back to parent...
Unsafe JavaScript attempt to access frame with URL http://www.theindychannel.com/news/14455773/detail.html from frame with URL http://ad.doubleclick.net/adi/N4441.Tacoda/B2166690.2;sz=160x600;click=http://an ad.tacoda.net/ads/ad13692a-map.cgi/BCPG78014.108755.106765/SZ=160X600A/V=2.1S//R EDIRURL=;ord=80595?. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.cnn.com/2007/TECH/10/30/vampire.electronics.ap/index.html from frame with URL http://ad.doubleclick.net/adi/N3941.cnn/B2492131.28;sz=728x90;click=http://ads.c nn.com/event.ng/Type=click&FlightID=86804&AdID=115255&TargetID=6869&Segments=934 ,2274,2607,2743,3030,3285,4008,4898,5217,6298,6520,6582,7465,8463,8796,9307,9496 ,9779,9781,9784,9853,9937,10033,10375,10956,11085,11877&Values=1588&Redirect=;or d=cnsqtAk,bdsozhntbinx?. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.cnn.com/2007/TECH/10/30/vampire.electronics.ap/index.html from frame with URL http://ad.n2434.doubleclick.net/adi/N2434.cnn/B2523462;sz=160x600;click=http://a ds.cnn.com/event.ng/Type=click&FlightID=87840&AdID=118718&TargetID=16970&Segment s=934,2276,2743,2872,3030,3285,3800,4008,6298,6520,6582,7463,8463,8796,9279,9308 ,9496,9779,9781,9784,9853,10028,10375,10511,11087&Values=1588&Redirect=;ord=cxtb Rkr,bdsozhotbioc?. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.cnn.com/ from frame with URL http://view.atdmt.com/BID/iview/trnrbbri1790000001bid/direct/01/bvNWKpj,bdsozizt bmKh?click=http://ads.cnn.com/event.ng/Type%3dclick%26FlightID%3d85378%26AdID%3d 112854%26TargetID%3d16956%26Segments%3d730,2259,2743,3030,3285,3464,3800,5216,62 01,6298,6301,6520,6582,7324,7464,8342,8463,8796,9276,9306,9496,9632,9742,9779,97 81,9784,9853,10031,10088,10381,11086,11360,11418,11636,11915,12036,12044%26Value s%3d1588%26Redirect%3d. Domains must match.
(event handler):Object (result of expression cnnSend) does not allow calls.
(event handler):Object (result of expression cnnSend) does not allow calls.
Unsafe JavaScript attempt to access frame with URL http://www.cnn.com/2007/SHOWBIZ/TV/10/30/tv.nbc.leno.ap/index.html from frame with URL http://ad.doubleclick.net/adi/N2870.cnn/B1880310.3;sz=160x600;click=http://ads.c nn.com/event.ng/Type=click&FlightID=62996&AdID=85296&TargetID=16970&Segments=657 ,2276,2743,2872,3030,3285,3800,4008,4558,6298,6520,6582,7463,8463,8796,9279,9308 ,9496,9779,9781,9784,9853,10028,10377,10511,11087&Targets=619,15951,2724,16970,1 515,11145,14921,18265&Values=30,46,50,61,73,82,91,100,110,150,682,917,1137,1285, 1557,1588,1598,1599,1600,1601,1697,1815,2675,2727,2743,4413,4418,4442,39896,4718 1,47734,48047,49553,49702,52263,52509,52738,52897&RawValues=ZIP%2C80201&Redirect =;ord=clWNguz,bdsoziRtbnmu?. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.cnn.com/2007/SHOWBIZ/TV/10/30/tv.nbc.leno.ap/index.html from frame with URL http://view.atdmt.com/BID/iview/trnrbbri1790000002bid/direct/01/bNjvlId,bdsoziRt bnms?click=http://ads.cnn.com/event.ng/Type%3dclick%26FlightID%3d85377%26AdID%3d 112853%26TargetID%3d16563%26Segments%3d657,2274,2607,2743,3030,3285,4008,4558,48 98,5217,6298,6520,6582,7465,8463,8796,9307,9496,9779,9781,9784,9853,9937,10033,1 0377,10956,11085,11877%26Values%3d1588%26Redirect%3d. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.cnn.com/2007/SHOWBIZ/TV/10/30/tv.nbc.leno.ap/index.html from frame with URL http://ad.doubleclick.net/adi/N2870.cnn/B1880310.3;sz=160x600;click=http://ads.c nn.com/event.ng/Type=click&FlightID=64204&AdID=85299&TargetID=16970&Segments=657 ,2276,2743,2872,3030,3285,3800,4008,4558,6298,6520,6582,7463,8463,8796,9279,9308 ,9496,9779,9781,9784,9853,10028,10377,10511,11087&Targets=619,15951,2724,16970,1 515,11145,14921,18265&Values=30,46,50,61,73,82,91,100,110,150,682,917,1137,1285, 1557,1588,1598,1599,1600,1601,1697,1815,2675,2727,2743,4413,4418,4442,39896,4718 1,47734,48047,49553,49702,52263,52509,52738,52897&RawValues=ZIP%2C80201&Redirect =;ord=cwkeRIN,bdsoziWtbnox?. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.macrumors.com/ from frame with URL http://pagead2.googlesyndication.com/pagead/ads?client=ca-pub-2224409576101196&d t=1193764276702&format=728x90as&output=html&correlator=1193764276702&channel=7440724589&url=http%3A%2F%2Fwww. macrumors.com%2F&color_bg=CBD3DE&color_text=000000&color_link=CC0000&color_url=0 08000&color_border=CBD3DE&ad_type=text_image&ga_vid=280090412.1193203054&ga_sid= 1193764275&ga_hid=892053144&ga_fc=true&flash=9&u_h=1200&u_w=1920&u_ah=1129&u_aw= 1920&u_cd=32&u_tz=-360&u_his=3&u_java=true&u_nplug=16&unmime=151. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://www.macrumors.com/ from frame with URL http://pagead2.googlesyndication.com/pagead/ads?client=ca-pub-2224409576101196&d t=1193764276702&format=728x90as&output=html&correlator=1193764276702&channel=7440724589&url=http%3A%2F%2Fwww. macrumors.com%2F&color_bg=CBD3DE&color_text=000000&color_link=CC0000&color_url=0 08000&color_border=CBD3DE&ad_type=text_image&ga_vid=280090412.1193203054&ga_sid= 1193764275&ga_hid=892053144&ga_fc=true&flash=9&u_h=1200&u_w=1920&u_ah=1129&u_aw= 1920&u_cd=32&u_tz=-360&u_his=3&u_java=true&u_nplug=16&unmime=151. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://forums.macrumors.com/showthread.php?t=376423 from frame with URL http://pagead2.googlesyndication.com/pagead/ads?client=ca-pub-2224409576101196&d t=1193764644335&format=728x90as&output=html&correlator=1193764644335&channel=8355507924&url=http%3A%2F%2Fforu ms.macrumors.com%2Fshowthread.php%3Ft%3D376423&color_bg=CBD3DE&color_text=000000 &color_link=CC0000&color_url=008000&color_border=CBD3DE&ad_type=text_image&ga_vi d=280090412.1193203054&ga_sid=1193764275&ga_hid=382955828&ga_fc=true&flash=9&u_h =1200&u_w=1920&u_ah=1129&u_aw=1920&u_cd=32&u_tz=-360&u_his=4&u_java=true&u_nplug =16&unmime=151. Domains must match.
Unsafe JavaScript attempt to access frame with URL http://forums.macrumors.com/showthread.php?t=376423 from frame with URL http://pagead2.googlesyndication.com/pagead/ads?client=ca-pub-2224409576101196&d t=1193764644335&format=728x90as&output=html&correlator=1193764644335&channel=8355507924&url=http%3A%2F%2Fforu ms.macrumors.com%2Fshowthread.php%3Ft%3D376423&color_bg=CBD3DE&color_text=000000 &color_link=CC0000&color_url=008000&color_border=CBD3DE&ad_type=text_image&ga_vi d=280090412.1193203054&ga_sid=1193764275&ga_hid=382955828&ga_fc=true&flash=9&u_h =1200&u_w=1920&u_ah=1129&u_aw=1920&u_cd=32&u_tz=-360&u_his=4&u_java=true&u_nplug =16&unmime=151. Domains must match.
[367] http://discussions.apple.com/resources/merge - Can't find variable: tinyMCE
The "unsafe JavaScript attempts" are mostly referring to websites I've accessed this am.
My concerns are:
-What the heck is Network Spy Alert?
-From the console log, any ideas what the HPEventHandler is or what the "HPTMNotificationManager" refers to? (Yes, I do have an HP printer but haven't sent anything to print today, so not sure why events need handling, unless this is some sort of automatic log-in thing?)
-What is "MagicMenuHotKeyDaemon 363"?
-What constitutes an "Unsafe JavaScript attempt?"
My question, in a nutshell, is whether this is all par for the course and I'm just noticing it because I happened to be looking into the iPhoto issue, or is there reason to feel paranoid at the mention of "spy," "Third Party Client," "sync" and "unsafe?"
Any info would be much appreciated!

You have (at least) two different issues going on there.
The first one (nsapAgent) is unrelated to the second (HPEventHandler's debug statement).
nsapAgent is a component of Allume's Internet Cleanup, so I suspect it is something you installed - or at least someone there did.
It may be that you're running an old version that is not compatible with your machine/configuration, but that's hard to tell.
I'm pretty sure that the Unsafe JavaScript messages are coming from this app, too.
I would expect that Allume's site would be a better source of information for that particular one.
As for the HPEventHandler, I'm guessing you have some kind of HP device there - a printer, scanner, or some such. The error message indicates that app had a problem, but it's impossible to be more specific without more information.

Trying to install speedit what do these commands mean?

Install.sh :
chmod -R 755 speedit.kext
chown -R root:wheel speedit.kext
kextload speedit.kext
sync;sync;sync
How do I run this?
Don't I need to point spmething to the command?
I have a foldert on my desktop named Speedit.
Inside it are three files:
Install.sh
speedit.kext
uninstall.sh
Can anyone give me specific commands for installation?
Install.sh has this inside it:
chmod -R 755 speedit.kext
chown -R root:wheel speedit.kext
kextload speedit.kext
sync;sync;sync
Typing these in terminal yields errors.
Thanks ... Ken

Here is a beginner friendly way to install SpeedIt.
1) http://www.increw.com/downloads/speedit/
Download "SpeedIt V 1.0 Preview for Tiger 10.4.8"
2) Extract its contents in your home folder, so that all the files like install.sh are in your home folder
3) Enable root user if not enabled already, open "NetInfo Manager" in Applications/Utilities folder and click Security (from the menu on the top) then click Enable root user.
4) Open Terminal and type these commands:
su (then type root password)
./install
That should load SpeedIt, remember you will have to do step 4 everytime you reboot. Also stay away from CoreDuo Temp because it will interfere with this utility as it uses a different version of speeit.kext if you want to know the temperature just type this in Terminal: sysctl speedit
MacBook Pro 1.83Ghz 1GB RAM Mac OS X (10.4.8)

What does these errors mean?

1. [07/Nov/2002:16:38:29 -0800] NSMMReplicationPlugin - Unable to acquire replica "
cn=Sample1, cn=replica, cn="o=company.com", cn=mapping tree, cn=config (host myhost
, port 389)": there is no replicated area "o=company.com" on the consumerserver. Replication is aborting.
2. [07/Nov/2002:18:34:11 -0800] NSMMReplicationPlugin - Unable to send a startReplication extended operation to consumer "cn=Sample1, cn=replica, cn="o=company.co
m", cn=mapping tree, cn=config (host myhost, port 389)". Will retry later.
Any help is appreciated..
Thanks

It means you need to
1) create the suffix and db for o=company.com on the consumer.
2) enable the replica for o=company.com on the consumer
Please refer to the documentation about setting up replication for more information.

My labtop keeps showing error codes 0601 and 03f0. What does these codes mean and how do I fix them?

HP Pavilion, Windows vista

Usually means the hard drive has failed, replace the hard drive and use the HP recovery discs to install windows.

What do these errors mean ? Web Logic 8.1 setting

I am a newbie in this Web Logic and I'm facing problem in my web application.
Appreciate that someone can guide me on this issue. I'm able to login to my web app and perform some interaction and but when I started to click on one of the contact button from front end I did receive this message "javax.naming.CommunicationException [Root exception is java.net.ConnectException:t3://localhost:7501,localhost:7551: Destination unreachable; nested exception is: java.net.ConnectException: Connection refused: connect; No available router to destination]".
Not sure I have to perform any of the configuration from the WebLogic console.
Below are the executed running cmd when I double click this file "*nodemanagerhelper.exe*" from my local C:bea\weblogic81\server\bin\nodemanagerhelper.exe
C:\bea\weblogic81\server\bin>set CLASSPATH=.;C:\bea\JROCKI~1\lib\tools.jar;C:\be
a\WEBLOG~1\server\lib\weblogic_sp.jar;C:\bea\WEBLOG~1\server\lib\weblogic.jar;
C:\bea\weblogic81\server\bin>cd C:\bea\WEBLOG~1\common\NODEMA~1
C:\bea\WEBLOG~1\common\NODEMA~1>if not "" == "" if not "" == "" goto runNMWithLi
stenAddressAndPort
C:\bea\WEBLOG~1\common\NODEMA~1>if not "" == "" goto runNMWithListenAddress
C:\bea\WEBLOG~1\common\NODEMA~1>if not "" == "" goto runNMWithListenPort
C:\bea\WEBLOG~1\common\NODEMA~1>"C:\bea\JROCKI~1\bin\java.exe" -jrockit -Xms32m
-Xmx200m -Xverify:none "-Djava.security.policy=C:\bea\WEBLOG~1\server\lib\weblo
gic.policy" "-Dweblogic.nodemanager.javaHome=C:\bea\JROCKI~1" weblogic.NodeManag
er
<Nov 23, 2010 4:00:06 PM EST> <Info> <NodeManager> <NodeManager: for information
on command line options, try "java weblogic.NodeManager -h">
<Nov 23, 2010 4:00:06 PM EST> <Info> <NodeManager> <Starting NodeManager >
<Nov 23, 2010 4:00:06 PM EST> <Info> <NodeManager> <Setting java home to 'C:\bea
\JROCKI~1'>
<Nov 23, 2010 4:00:06 PM EST> <Info> <NodeManager> <Effective values of properti
es :
ListenAddress=*.*
ListenPort=5555
ListenerType=secureSocket
SavedLogsDirectory=NodeManagerLogs
NativeVersionEnabled=true
TrustedHosts=nodemanager.hosts
StartTemplate=../../server/lib/unix/nodemanager.sh
ReverseDnsEnabled=false
ScavangerDelaySeconds=180
PIDFileReadRetryCount=0
WeblogicHome=null
bea.home=null
JavaHome=C:\bea\JROCKI~1
PropertiesVersion=8.1
>
<Nov 23, 2010 4:00:06 PM EST> <Info> <NodeManager> <Saving logs in'NodeManagerLo
gs'>
<Nov 23, 2010 4:00:11 PM EST> <Info> <NodeManager@*.*:5555> <Reading private key
and certificate chain from the keystore C:/bea/weblogic81/server\lib\DemoIdenti
ty.jks. KeyStore type = jks, Using keystore passphrase = true, Alias = DemoIdent
ity>
<Nov 23, 2010 4:00:11 PM EST> <Info> <NodeManager@*.*:5555> <Reading trusted CAs
from the keystore C:/bea/weblogic81/server\lib\DemoTrust.jks. KeyStore type = j
ks, Using keystore passphrase = true>
<Nov 23, 2010 4:00:11 PM EST> <Info> <NodeManager@*.*:5555> <Reading trusted CAs
from the keystore C:\bea\JROCKI~1\jre\lib\security\cacerts. KeyStore type = jks
, Using keystore passphrase = false>
<Nov 23, 2010 4:00:11 PM EST> <Info> <NodeManager@*.*:5555> <Node Manager listen
ing on *.*:5555..>
<Nov 23, 2010 4:00:11 PM EST> <Info> <NodeManager@*.*:5555> <NodeManager started
, log messages being written into file C:\bea\WEBLOG~1\common\NODEMA~1\NodeManag
erLogs\NodeManagerInternal\nm_KLIS045_11_23_2010-16_00_07.log>
Edited by: 814719 on Nov 23, 2010 4:30 PM
Edited by: 814719 on Nov 23, 2010 4:34 PM
Edited by: 814719 on Nov 23, 2010 4:40 PM

Thanks. I amended the Web Login console with listen port "7501" and corrected the local host link..it should be pointing to this link http://localhost:7501/Web/index.jsp instead of http://localhost:6501/Web/index.jsp
Edited by: 814719 on Nov 24, 2010 8:20 AM

ReSampling? Hot Swapping? What do these terms mean?

Similar Messages

Maybe you are looking for