Reset and will not connect to wifi

we accendently reset our apple tv 3 and can not get it to connect to our movie storage computer just wondering if we need to have internet to set it up before it will work i have hooked up the apple tv and did update but does it need to verify my username and password to work?

You won't need an internet connection, but you will need a network connection in order to use home sharing. If you have any iTunes purchases it will need the internet for verification.

Similar Messages

  • Since updating my airport utility app to iOS 8, it can no longer see my base station and will not connect to wifi.

    Since updating my airport utility app to iOS 8, it can no longer see my base station and will not connect to wifi. My son's 4s with an older version of the app sees it and connects fine, so I know it's working. The internet works fine for everyone else in the house but my

    Please take a look at this Apple support document to see if it help solve your issue:
    iOS: Troubleshooting Wi-Fi networks and connections
    If this does not help, we would recommend that you post in the iPhone community support area, since you have an iPhone / iOS issue. The link is just below.
    Using iPhone

  • My air has a self assigned ip address and will not connect to wifi. I cannot access the wifi through the safari guest account nor my parallels Win 7. I have erased my keychain access, erased the 3files and renewed the DHCP lease. Nothing works. I am on

    I

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • HT1688 Iphone 4 will not connect to wifi, and there is NO password on it, i have reset network connections, and it wont connect. I click other and typed the name of the wifi in and it will not work, what do i do.

    I phone 4 will not connect to wifi, and there is no password, i have tried and tried and nothing works, also the lock button doesnt work, i bought off from someone on facebook and now it will not connect to the wifi, PLEASE HELP

    http://support.apple.com/kb/TS1398

  • I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. Bad job testing the software Apple.

    I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. What's the fix? None of the recommended fixes work in any of these devices. Reset device, reset network, renew lease, etc. None of them work.

    Does the iPod work OK?
    Does it charge when connect to the computer?
    Does it appear in My Computer?
    Look at the dock connector on the iPod. Compare with the iPod that does work/connect.
    I suspect you have a 2G iPod. Those can only go to iOS 4.2.1
    http://support.apple.com/kb/HT1353#iPod_touch_late2009
    iPod touch (3rd generation)
    iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
    The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.

  • My imac will not connect to wifi what so ever. i have tried 3 different routers and all my other apple devices work fine. when i take it to the genius bar it seems to work with apples instore wifi. thus leading the "geniuses" to say nothing is wrong.

    my imac will not connect to wifi what so ever. i have tried 3 different routers and all my other apple devices work fine. when i take it to the genius bar it seems to work with apples instore wifi. thus leading the "geniuses" to say nothing is wrong.

    Back up all data before making any changes.
    Step 1
    Take all the applicable steps in this support article.  
    Step 2
    If you're running OS X 10.8.4 or later, run Wireless Diagnostics and take the remedial steps suggested in the summary that appears, if any. The program also generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
    Step 3
    If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. Continue if you find that Wi-Fi is faster with Bluetooth disabled.
    From that same menu, select Open Bluetooth Preferences. If the box labeled Discoverable is checked, uncheck it. Click the Advanced button, and in the sheet that opens, uncheck the top three boxes, if any are checked. Click OK. Enable Bluetooth and test again.
    If the application called "Bluetooth Setup Assistant" is running, quit it.
    Step 4
    This step will erase all your settings in the Network preference pane. Make a note of them before you begin, and recreate them afterwards. It may be helpful to take screenshots of the preference pane.
    Triple-click the line below on this page to select it:
    /Library/Preferences/SystemConfiguration
    Right-click or control-click the highlighted line and select
    Services ▹ Reveal
    from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard (command-C). In the Finder, select
    Go ▹ Go to Folder...
    from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
    Step 5
    Reset the System Management Controller.
    Step 6
    Make a "Genius" appointment at an Apple Store, or go to another authorized service center.
    Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
    If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present. 
    Keeping your confidential data secure during hardware repair
    *An SSD doesn't need to be zeroed.

  • My iphone will not connect to wifi...the wifi option is greyed out...i tried resetting network, no luck

    My iPhone 4 will not connect to wifi...the option is greyed out...I tried resetting network but nothing happens.

    Hello there, LTD1111.
    It seems you've done some great troubleshooting so far. The following Knowledge Base article offers a few steps you may want to review, and it also provides some additional recommendations if the issue persists:
    iOS: Wi-Fi settings grayed out or dim
    http://support.apple.com/kb/ts1559
    Resolution
    Follow these steps to resolve the issue:
    Restart your iOS device.
    Make sure that airplane mode is off by tapping Settings > Airplane Mode.
    Reset the network settings by tapping Settings > General > Reset > Reset Network Settings.
    This will reset all network settings, including Bluetooth pairing records, Wi-Fi passwords, VPN, and APN settings.
    Make sure that your device is using the latest software. To do so, connect your device to your computer and check for updates in iTunes.
    If you still can't turn Wi-Fi on, please contact Apple for support and service options. If you can turn Wi-Fi on but are experiencing other issues with Wi-Fi, please see these steps.
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • Just updated my iphone 4s to the new IOS6 and now my wifi is bringing up an itunes page and will not connect?

    i just updated my iphone 4s with the new IOS6 update and now everytime i try to connect to my wifi it brings me to the apple page and will not connect to the wifi at all.. someone please help

    I have the same problem, no way to change the old username in icloud on my ipad after update to ios7. Enybody knows a solution or where to look for a solution?

  • My daughters ipod 4th gen will no longer charge past 20% and will not connect to a pc in order to back everything up. the cable is working fine, otherwise it would not even charge to the 20%. i have tried the reset to not lose any data and no luck. help!

    my daughters ipod 4th gen will no longer charge past 20% and will not connect to a pc in order to back everything up. the cable is working fine, otherwise it would not even charge to the 20%. i have tried the reset to not lose any data and no luck, home+power for 10-15 seconds. I really would like to not lose everything she has, again, because I can't back it up this time. I have tried charging via a wall outlet and PC and both charge fine, just only to 20%. I am using the cable that came with it so no aftermarket issues there. Please help so I don't have to reset everything again.

    Because once it has charged enough to be powered on as soon as you turn it on it says battery is at 20% and will not charge anymore after that, it just runs for about 5-10 minutes before the battery dies again. The battery cycles discharge/recharge daily and its not on the charger at full charge for more than a couple hours and is never totally dead for more than a couple of hours.

  • I try to connect to wifi in hotel. It shows its connected to the network but it never takes me to sign on screen and will not connect even though wifi shows full bars

    I try to connect to wifi in hotel. It shows its connected to the network but it never takes me to sign on screen and will not connect even though wifi shows full bars

    Have you tried clearing Safari? Clear Safari, close Safari completely and reboot your iPad. Try again.
    Go to Settings>Safari>Cookies and Data.
    If you are running iOS 5 or iOS 6 you close apps like this. Tap the home button once. Then tap the home button twice and the recents tray will appear at the bottom of the screen. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button twice.
    If you are running iOS 7, you close apps this way. Double tap the home button and you will see apps lined up going left to right across the screen. Swipe to get to the app that you want to close and then swipe "up" on the app preview thumbnail to close it.
    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.

  • My IPhone 4s will not connect to wifi, what can I do?

    My IPhone 4s will not connect to wifi, what can I do?i have tried network reset, turning wifi off and on but my phone will not connect to any network.

    Hi jazznola9,
    Welcome to the Apple Support Communities!
    There are several steps you can take when troubleshooting Wi-Fi connectivity on an iPhone and it sounds like you have already done a few of them already. In your situation I would recommend reading over and working through the steps listed in the attached article.
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/TS1398
    Have a great day,
    Joe

  • IPod Touch 4gen will not connect to wifi no matter what

    My white 8gb iPod Touch 4gen will not connect to wifi, I have reset the network and the entire iPod. When I got it for Christmas 2011 it worked perfectly for a few months then all of a sudden it stopped connecting, every connection I try to connect it to says the same thing; unable to join network... I am getting fed up, my first gen iPod Touch will connect to the wifi no problem, but the thing is it keeps crashing. I can't use it for more than a couple of minutes and it goes back to the home screen. If anyone could help, it is greatly appreciated!

    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • Macbook will not connect to wifi, an environmental issue with wifi?

    Macbook running OSX 10.85 will not connect to wifi, Apple support thinks it could be an environmental issue.  Am connected to wifi right now in recovery mode.  Has this happened to anyone else?  What did you do to correct the issue?  Also, 2 iPhones and an iPad connect without issues.

    Back up all data before making any changes.
    Step 1
    Take all the applicable steps in this support article. If you're running OS X 10.8.4 or later, run Wireless Diagnostics and take the remedial steps suggested in the summary that appears, if any. The program also generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
    Step 2
    Run Software Update and install all available updates for OS X or your computer's firmware.
    Step 3
    If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. Continue if you find that Wi-Fi is faster with Bluetooth disabled.
    From that same menu, select Open Bluetooth Preferences. If the box labeled Discoverable is checked, uncheck it. Click the Advanced button, and in the sheet that opens, uncheck the top three boxes, if any are checked. Click OK. Enable Bluetooth and test again.
    If the application called "Bluetooth Setup Assistant" is running, quit it. Note: this is not applicable to OS X 10.9 or later.
    Step 4
    This step will erase all your settings in the Network preference pane. Make a note of them before you begin, and recreate them afterwards. It may be helpful to take screenshots of the preference pane.
    Triple-click the line below on this page to select it:
    /Library/Preferences/SystemConfiguration
    Right-click or control-click the highlighted line and select
    Services ▹ Reveal
    from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
    Go ▹ Go to Folder...
    from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
    Step 5
    Reset the System Management Controller.
    Step 6
    Make a "Genius" appointment at an Apple Store, or go to another authorized service center.
    Back up all data on the internal drive(s) before you hand over your computer to anyone. There are ways to back up a computer that isn't fully functional — ask if you need guidance.
    If privacy is a concern, erase the data partition(s) with the option to write zeros* (do this only if you have at least two complete, independent backups, and you know how to restore to an empty drive from any of them.) Don’t erase the recovery partition, if present. 
    Keeping your confidential data secure during hardware repair
    *An SSD doesn't need to be zeroed.

  • IPad will not connect to wifi, shows connection, iPad will not connect to wifi, shows connection

    My iPad will not connect to wifi, even though my computer is currently connected.  Airport mode is off, and my iPad shows connectivity in the corner.  Is there any way to fix this without completely resetting the device?

    - Reset the iPad. Nothing will be lost
    Reset iPad: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router.
    - Reset networks settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points
    Does the iPad successfully connect to other networks?
    Did it successfully connect to this network before?

  • My 6 day old touch will not connect to wifi .

    My 5 day old touch will not connect to wifi. I have reset everything. Tried different networks.  I am willing to do a full restore but because I have no internet I can't turn "find my ipod off"
    It worked when I first opened it then it kept disconnecting. I reset "all network setting" and rebooted my router and it would connect.  Now it will not connect at all
    On my ipod it finds the network and when I try to put in password it say "incorrect password"

    Then restore the iPod using the following
    Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
    iOS: Forgot passcode or device disabled
    If recovery mode does not work try DFU mode.                        
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings        
    For how to restore:                                                             
    iTunes: Restoring iOS software
    To restore from backup see:
    iOS: Back up and restore your iOS device with iCloud or iTunes       
    If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
    You can redownload most iTunes purchases by:                         
    Downloading past purchases from the App Store, iBookstore, and iTunes Store        
    If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.

Maybe you are looking for

  • Problem installing Oracle 8.05 on Redhat Linux 7.1

    I am currently trying to install Oracle 8.05 onto Redhat Linux 7.1. I can get part of the way through the installation, however, when it is installing the rdbms portion. I stops with an error about a failure during relinking. Here is the part of make

  • Epson Stylus Pro 7700 will not work after installing Mountain Lion, I have update all drivers and firmware

    This is a large format printer used for proofs that I cannot use since upgrading to Mountion Lion, anyone else had printer issues?

  • Embedding and using external fonts in Flash CS5

    I just upgraded to Flash CS5.  Font embedding is entirely different than it was in CS4.  I've been looking for examples online but none seem to show me a solution that matches what I need. In the project I'm working on, code changes the font a text b

  • Oracle 11g - External Table Issue?

    Oracle 11g - External Table Issue? ===================== I hope this is the right forum for this issue, if not let me, where to go. We are using Oracle 11g (11.2.0.1.0) on (Platform : solaris[tm] oe (64-bit)), Sql Developer 3.0.04 We are trying to us

  • Service Master - Unit of Measure

    Hi all - had a question about services and alternate unit of measure. On a service master, its not possible to specify alternate UoM (like we do in material master). What is the process to say create a service in minutes and create a PO in hours ? an