Reset button inactive

Hello, for some reason the reset button of my iphone 4 sometimes does not work anymore. I'll press of it and nothing happens. To reboot or restart does not do anything. It can stay like this for a while and work again sometimes later.
Should it comes from a electric contact problem ?
Thanks for your help

You mean the home button? The reset button would be inside the Settings. I'd take it to the apple store and have the genius check it out. Make sure you set up an appointment.

Similar Messages

Inactive (or broken) reset button on my Ze

Hello! I recently tried using the recovery tool on my zen V to diagnose any issues. The player had been charging on the computer for some time but was not being recognized by the computer itself (not unusual). So when I tried to use the recovery tool, it obviously said there was no player connected and thus couldn't continue the diagnosis. That is fine and dandy but the problems now are much much worse... After that, I tried removing it and re-plugging it in. The player was detected but not recognized by the computer (strange, I've used it on this computer before). I wasn't overly concerned yet but then the player itself started acting strangely --> freezing while "restoring library". I used the reset button and went to the recovery mode to reboot the player. The player rebooted successfully and restarted the song it had cutoff when the battery died. I tried going to other menus and then the player froze again. Once again, I used the reset button to get into recovery mode and tried to re-boot. It once again froze when trying to restore the library... so I tried the reset button yet again. Finally it loaded, started playing the song again and when I tried switching the menu, it froze YET again! Now, my reset button will not work and it is stuck with the screen on, sitting in the menu section. Does anyone have any suggestions as to what I can do I've owned the player for < year.

Mark,
Is the web interface simply not loading or do you not have the password? Your DHCP range does not matter unless there is another device on the network that is currently assigned 192.168.1.254. If that is the case you will have trouble accessing the web UI. It is usually easiest to plug ONLY a PC and the switch together and assign a static IP to the PC:
IP Address: 192.168.1.200
Subnet Mask: 255.255.255.0
Default Gateway: None
DNS Servers: None
This will allow you to access the switch without interference from other network devices. Remember to change the PC back to DHCP when you are done. If you do in fact have an IP conflict you should also change the switch to a different static IP.
You can also access the switch using a console cable. You can check the settings and see if the web interface has been disabled or you can reset the password in case you lost it. Check the Admin Guide for details:
http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/78-19308-01.pdf
Let us know if you have any other questions.
- Marty

How to make a RESET button in labview ?

how to make a RESET button in labview which resets all the elements in an array back to inactive element. Rather than deleting values in every column of array its better to create a RESET button ... how to make it ???

abhinavb wrote:
how to make a RESET button in labview which resets all the elements in an array back to inactive element. Rather than deleting values in every column of array its better to create a RESET button ... how to make it ???
You seem to have some misconceptions.
Is the array a control or an indicator or just some data held in a shift register or feedback node?
What you are probably looking for is an empty array. An empty array has a size of zero and has no elements (active or inactive). From your mentioning of "rows", you seem to have a 2D array.
The size of the array is independent of the visible size of the container.
Clearing an array means simply writing an empty array of the same datatype to it's terminal (or internal data structure). If the array is a control, you need to write to a local variable of it instead.
Can you show us some code so we can have a better understanding what exactly you mean by "array" in this context? Thanks!
LabVIEW Champion . Do more with less code and in less time .

My G4 powerbook starts up but with a black screen. The reset button does not work. Does anyone know the keys to press on restart please ?

My G4 powerbook running OSX 10.3.9 starts up with a black screen. The reset button is not working. Does anyone know which keys to press on restart please.?

Try holding the shift key while booting to get Safe mode if possible.
See links for more info.
http://support.apple.com/kb/ht1564
http://support.apple.com/kb/ht1455

I bought an iphone 4 from my friend and he do not know his apple ID and we are trying to know the email attached to is apple ID so we can rest it cause he forgot them as well and the reset button in the 2 steps always says that the email is always sent !

i bought an iphone 4 from my friend and he do not know his apple ID and we are trying to know the email attached to is apple ID so we can rest it cause he forgot them as well and the reset button in the 2 steps always says that the email is always sent ! ( even if you wrote a worng ID like ( asdasdasd ) it will say sent !! how come and now am trying to know or need a hint on that email so my freind could try to remember it !
to those who will think that this phone is stolen , no its not and i would love to go to apple store if there is 1 in jordan so they can help us ,
i have everything with this iphone the box the catalog its serial number , everything but the ID and the (and apple ID is everything as you know)
so please if anyone have any suggestion to help me , and even apple it self if the can help me to get a support from them cause i tried everything to contact them by mail or any other option since as i said there is no apple store in jordan

he knows his ID , if he did all whats in the link he can get his password back ?
how can i make him call applecare ? is there a way to speak to them from jordan ??
i have been trying to reach any1 in apple so they can communicate and help my friend (us) to make him remember it .
am not asking for the password or trying to get into the phone without using it , and i can take my money back though i need to help my friend as well since now he cant use it as well.
thanks kil

How to get the submit and Reset buttons on bottom of the page?

while viewing a parametric form in the web browser i get SUBMIT
and RESET buttons on the top of the form which doesnt look good.
I tried pasting the whole html available by default in the
Before Form Value(where the submit and reset buttons are
defined) in the After Form Value property of the report property
pallette. Though the layout appears as i wanted but its not
passing the parameters values to the query but generates an
error " REP-0788 Warning : The value of restricted LOV parameter
BV_FROM_DATE is not among the selected values.". What can be the
solution to this problem? Your Help is much appreciated. And
also the report generated in the Runtime Previewer shows all the
colors of the fields but its not shown on the web browser where
can i define them...Your Help!!!!Thank you very much in
advance..

when you select 'list of values for the parameters' there is a choice box that says 'restrict list to Predetermined values'. Don't select it. This will solve your first problem.
Second:When you run the report on the web you must choose ' desformat=htmlcss' then you can display the report as in the preview window. But still you can't see the same view in the web browser on report builder. It is still not good. As I sad before you can see the right view when publishing on the web.

E3000 Pressed reset button on back. I just want my old router back :(

Hey all. I have an E3000 router that I love. One day after coming back from a vacation, I noticed another computer that wasn't mine connected to my network(I live in an apartment complex). I tried logging into my router but had completely forgotten the login info. Knowing me I push buttons first, ask questions later and hit the reset button on the back. Terrible idea, I had no internet connectivity at all wired or wireless. The only way I could connect was through my modem. After chatting with Cisco tech support and changing a bunch of ips, dns. I was able to connect wireless devices. But something was still missing. My printer would still not connect, and my NAS was unreachable. Here is where you guys might help me. Is there any way to return my E3000 back to its original fresh out of the box state? I was able to connect everything to it and everything played nicely with each other. Please, I just want my old router back!
Thanks
Eric

wumbo6 wrote:
when i chatted with the cisco support guy he walked me through manually changing all my settings. yea i tried power cycling.
Can you tell what is the IP address of the router? the printer and the NAS?
Yesterday is history. Tomorrow is mystery. Today is a gift.

Location of the SMC Reset button in a Mac Pro

I'm having trouble finding the SMC reset button.
+The hatter+ said, "use the SMC RESET button inside, under drive #4. "
This page http://docs.info.apple.com/article.html?artnum=304123 said;
"Another way to reset the SMC on a Mac Pro computer is:
From the Apple menu, choose Shut Down (or if the computer is not responding, hold the power button until it turns off).
Open and remove the metallic outer door.
Press the SMC_RST switch that is located slightly below and to the right of the row of diagnostic LEDs. Use a non-metallic, non-conductive object, such as a wooden pencil.
Replace the metallic outer door.
Press the power button to start up your computer."
I can't see any row of LED's - can't even see one inside there...
Can anyone help me with the location of this button?
Thanks

Full glossy photos:
http://mac.powerbras.nl/
It is as small or smaller than the eraser on a pencil.
It is easier to see with a flashlight and with the case over on its side, and pull out drive #4.
I thought Apple had a page with a circle around it in the tiny pdf or manual that came with the unit. They should have it in the tech note.
and if you have a PCI card in the top slot, someone said they had to remove it to get access.

Add a reset button to a formCentral form

Is it possible to add a cancel or reset button to a form that will close the form and not proceed to submit the form?

Hi DogPACT,
It is not possible to add Cancel or Reset button in PDF form using FormsCentral.

Is it possible to hide or at least change the position of the Reset button in registration template?

Hi,
in the registration template there are always the Submit and Reset buttons.
2 questions regarding the Reset button:
from a usability stand point: what's the reason of putting the Reset button equally weighted (from a visual standpoint) next to Submit?
wouldn't it be better to have placed on the left?
(or even hide it?)
Thoughts?
Thanks.

Hi,
It is not recommended to modify this page because it is used farm widely.
What’s more, it will be overwritten once there is upgrade happens.
A workaround is that you can create a custom spcf.aspx page with the layout templates you want.
http://doitwithsharepoint.blogspot.com/2011/08/create-web-part-pages-with-custom.html
http://sandeeppawar.blogspot.com/2012/06/create-custom-web-part-page-template.html
If you want to hide a layout template by modifying the
spcf.aspx page, it locates at
C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\14\TEMPLATE\LAYOUTS
You can edit this page and remove some <option> tags in the <select> tag, then the removed options will not display on the page.
Thanks
Patrick Liang
Forum Support
Please remember to mark the replies as answers if they
help and unmark them if they provide no help. If you have feedback for TechNet
Subscriber Support, contact [email protected]
Patrick Liang
TechNet Community Support

OBIEE 11g Dashboard Prompt Reset Button Functionality

Dear Experts,
Can anyone explain what is the exact functionality of 'Reset' Button in any OBIEE 11g Dashboard Prompt.
If anyone found any documentation related to it... please let me know.
thanks,
Varun

Hi Varun,
This is the functionality of Reset button,
Reset will go back to last applied values. It does not clear values. Currently the Reset button works in the following ways:
if 1) the prompt is blank 2) select some value, 3) reset 4) it should go back to blank.
if 1) the prompt is blank 2) select some value, 3) apply 4) reset. 5) it should NOT to back to blank. actually it does not change anything.
if 1) the prompt is blank 2) select some value, 3) apply 4) change any values 5) reset. 6) it should undo any changes in step 4.
Rgds,
Dpka

1st Generation Time Capsule reset button broke

Hello everyone I have a 1st Generation Time Capsule 500gb that I purchased used and do not have the password for AND
the reset button is BROKEN!!!
Is there anyway to reset it without the rest button working??
I bought it to upgrade it to a 2TB drive that i already own .
Thank you guys !!!!!!!

When you open the TC to replace the hard disk you will be able to press the reset. You might also be able to fix the reset lever arm.. I have found them simply forced so far back it was bent.. and no longer able to go back.. once inside the box, I can bend it back to the correct position.. but it is a plastic hinge.. and no plastic hinge likes being bent at any time.. If it has snapped right off, or snaps off attempting repair don't worry about it.. once reset, just keep it at default or write the password on a sticker and place it on the bottom.
http://www.ifixit.com/Device/Apple_Time_Capsule
Please pay attention though to Bob's comments.. fixing the power supply is going to be necessary in the near future. Especially if you put in a large drive with high start current for the hard disk. There are lots of people who find the upgrade of the hard disk is closely followed by power supply failure or it won't even start the new hard disk.. depending on type and current demand. It is much much more for some disks even if the drive has lower consumption.
If you are a DIYer it is not expensive to fix power supply or better replace it.
Although I have suggested several repair methods this is probably the cheapest.
https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair/cisco-adp-30rb-4pin-molex

Page Number Disappesrs when click on Reset button in Dynamic Form

Dear all,
In dynamic forms I have taken Page n of m field outside the content area in master pages.I have added the reset button in body pages of the form.In the pdf When I click on Reset button the page nos are disappearing along with the other data.
I want the page no should not disappear.How can I get rid of this problem. If any body can please help me.
Thanks a bunch in advance
Regards
Rakesh

Firefox checks on the server if the file has been modified if you use the back button.<br />
If the page was requested by sending post data to the server then Firefox sends that post data and asks for confirmation.<br />
You can try to use the tab history of the Back button skip sites that require sending post data.
You can also try if it works if you set to never check the server by setting the browser.cache.check_doc_frequency pref to 2.
*http://kb.mozillazine.org/browser.cache.check_doc_frequency

I was working on my iPad 1 and it turned off and now it won't turn back on. It was 50% charged and even when I connect it to be charged it still won't turn on. Is there a reset button?

I was working on my iPad and it turned off suddenly and now it won't turn back on. It was at least 50% charged and when I tried to connect the charger it still will not come on. Is there a reset button?

Thank you so much! It worked, I was reading around and saw this has happened to a number of iPad users. Thank you for your prompt response, I was so worried I broke it or something.

2nd Gen Time Capsule - will not power up - just stopped working all of a sudden - I have tried other power outlets - I have tried pressing the reset button - no light

2nd Gen Time Capsule - will not power up - just stopped working all of a sudden - I have tried other power outlets - I have tried pressing the reset button - no light

The power supply is shot. But that it lasted even this long is the wonder.. not that it died.
The TC runs too hot..
Look on ebay for "Time Capsule power supply"
You can get a replacement and fix it although the economics are not so good.. it is probably time for a new TC.
If you can DIY it is really only a few dollars worth of capacitors that go bad.
See https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair
For a bunch of alternatives.

Reset button inactive

Similar Messages

Maybe you are looking for