Reset default cisco sap1602e-e-k9 error tftp://255.255.255.255/ap1g2-k9w7 -tar.default

i am to try download ap1g2-k9w7 -tar.default but not correct. 

Using mode button, you can do this. Here is a reference post on that
http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
HTH
Rasika
**** Pls rate all useful responses *****

Similar Messages

  • Cisco AIR-CAP26021-A-K9 || Error opening tftp:// ... /ap3g2-k9w7-tar.default

    Hi everyone:
    I have a problem with two Cisco AIR AP's ... I have configured already eight of them (in lightweight mode), but those two send me the next error, right now.
    ap: %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)
    And when I boot to the AP, it says:
    %Error opening flash
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Numonyx Mirrorbit (0089)
    Xmodem file system is available.
    flashfs[0]: 11 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 15 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Ethernet speed is 100 Mb - FULL Duplex
    button is pressed, wait for button to be released...
    button pressed for 21 seconds
    process_config_recovery: set IP address and config to default 10.0.0.1
    process_config_recovery: image recovery
    image_recovery: Download default IOS tar image tftp://255.255.255.255/ap3g2-k9w7-tar.default
    examining image...
    DPAA Set for Independent Mode
    DPAA_INIT = 0x0
    %Error opening tftp://255.255.255.255/ap3g2-k9w7-tar.default (connection timed out)ap:
    ap:
    ap:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Numonyx Mirrorbit (0089)
    Xmodem file system is available.
    flashfs[0]: 10 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 14 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Ethernet speed is 100 Mb - FULL Duplex
    Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx"...###########################
    File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 10 files, 2 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 7245824
    flashfs[0]: Bytes available: 24752128
    flashfs[0]: flashfs fsck took 7 seconds.
    Base Ethernet MAC address: c0:67:af:6f:31:25
    Boot CMD: 'boot  flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx'
    Loading "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx"...#####################
    File "flash:/ap3g2-rcvk9w8-mx/ap3g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x2003000
    executing...
    Initializing flashfs...
    flashfs[2]: 10 files, 2 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31739904
    flashfs[2]: Bytes used: 7245824
    flashfs[2]: Bytes available: 24494080
    flashfs[2]: flashfs fsck took 8 seconds.
    flashfs[2]: Initialization complete.
    flashfs[3]: 0 files, 1 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 11999232
    flashfs[3]: Bytes used: 1024
    flashfs[3]: Bytes available: 11998208
    flashfs[3]: flashfs fsck took 0 seconds.
    flashfs[3]: Initialization complete.
    Copying radio files from flash: to ram:
    %Error opening flash:/ap3g2-rcvk9w8-mx/E2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/B2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/V2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/X2.bin (No such file or directory)
    %Error opening flash:/ap3g2-rcvk9w8-mx/Y2.bin (No such file or directory)
    Uncompressing radio files...
    File not found: flash:/ap3g2-rcvk9w8-mx/8004.img
    File not found: flash:/ap3g2-rcvk9w8-mx/E5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/B5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/V5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/X5.bin
    File not found: flash:/ap3g2-rcvk9w8-mx/Y5.bin
    ...done Initializing flashfs.
    Press RETURN to get started!
    *Mar  1 00:00:11.335: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:13.071: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:13.663: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C2600 Software (AP3G2-RCVK9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 23:08 by prod_rel_team
    *Mar  1 00:00:13.795: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:13.795: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
    *Mar  1 00:00:13.799: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:14.751: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:16.467: DPAA Initialization Complete
    *Mar  1 00:00:16.467: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Mar  1 00:00:16.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    no bridge-group 1 source-learning
                       ^
    % Invalid input detected at '^' marker.
    %Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:00:47.151: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inline power source
    *Mar  1 00:00:49.515: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.44.221, mask 255.255.255.0, hostname APc067.af6f.3125
    Translating "CISCO-CAPWAP-CONTROLLER.asf.gob.mx"...domain server (10.1.1.2)
    *Mar  1 00:01:00.403: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Mar  1 00:01:00.451: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.asf.gob.mx
    The thing is, I've been applying the instruction:
    capwap ap controller ip address 10.4.13.2
    'cause I want them to communicate with a remote controller, and the past eight did it fine, but this two didn't.
    As for the things I've already tried, I have reset it's parameters to it's initial settings, I've tried to load a new IOS image, I've cleared the flash memory, but nothing works, it keeps communicating with the old controller.
    How can I fix this? (I mean, changing or adapting the AP to a lightweight AP)
    Thanks in advance

    Its fine to try to apply it from the console...but if you really want to clear the AP, you need to clear the nvram.  so if changing the primary from the GUI that the AP has joined didn't work, then try this:
    debug capwap console cli
    erase /all nvram
    Example:
    Entered the username and password
    debug capwap console cli
    erase /all nvram:
    [confirm]
    undebug all
    reload
    [confirm]
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Air-ap1121g-a-k9 will not recieve c1100-k9w7-tar.default from tftp

    I have 3 of these units that have no image and need an image loaded but they will request the file from the tftp server but wont recieve it. Any Clues to what could be going on?
    Thanks ahead of time

    Hi Gary,
    Sounds like a TFTP problem for sure :(
    Have a look at the details in the following threads that all have to do with TFTP. There are some great hints for troubleshooting TFTP problems from some of my favourite NetPros like ScottMac,Stephen from Cisco and Jack Young. The likely culprit may be that you need to uncheck "hide extensions for known file types" on your TFTP server;
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=WLAN%20Radio%20Standards&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc042b/8#selected_message
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddc03c4/2#selected_message
    http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddbf271
    Maybe try this (highly recommended version)
    Solar Winds tftp
    http://www.solarwinds.net/Tools/Free_tools/TFTP_Server/
    The problem could be that the Laptop (used for TFTP) Operating System is hiding the known file type. From Internet Explorer, go into Tools > Folder Options > View, scroll down until you find the parameter Hide extensions for known file types, and uncheck the box. This should eliminate the issue.
    Hope this helps! Good Luck!
    Rob

  • Failed to execute default file manager (input/output error) After Firefox Reset? [Any more help? you guys/gals rule!]

    after resetting firefox it seems I cant open anything from the menu as i get the above error msg.

    Are you using ubuntu? [http://askubuntu.com/questions/42682/failed-to-execute-default-file-manager-input-output-error]

  • Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command

    Trying to Download a Software Image to Cisco 2800 series router through TFTP Using the tftpdnld ROMmon Command
    and I am getting an Error , I cant figure out what I am doing wrong. I have also pasted my display down here can someone help me out, thanks in advance, I am still new to this utility.
    My questions are How do you direct this utility to point to the desktop or the TFTP folder
    does FE_PORT: Fast Ethernet 0 imply or point to Fa0/0 on my router
    My router is suppose to have 10.0.0.3 255.0.0.0
    Gateway of 10.0.0.1 255.0.0.0
    My TFTP Server 10.0.0.2 255.0.0.0
    How do I get the MAC address of the Router or the TFTP Server and which one  is required?
    my Ethernet port is 100Mb/Sec I cant tell whether it is full duplex or not so How do i set this FE_SPEED_MODE: Auto???
    =====================================================================================
    rommon 10 >
    rommon 10 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    ?=0
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=
    rommon 11 > TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    rommon 12 > TFTP_CHECKSUM=0
    rommon 13 > SET
    monitor: command "SET" not found
    rommon 14 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    ?=0
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    rommon 15 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 16 >       " not found
    rommon 17 >FE_SPEED_MODE=2
    variable name contains illegal (non-printable) characters
    rommon
    rommon 18 > set
    PS1=rommon ! >
    FE_PORT=0
    WARM_REBOOT=
    RET_2_RTS=20:35:55 UTC Thu Sep 25 2014
    BSI=0
    RET_2_RCALTS=
    RANDOM_NUM=1600357627
    IP_ADDRESS=10.0.0.3
    IP_SUBNET_MASK=255.0.0.0
    DEFAULT_GATEWAY=10.0.0.1
    TFTP_SERVER=10.0.0.2
    TFTP_FILE=c2800nm-adventerprisek9-mz.124-24.T4
    TFTP_CHECKSUM=0
    ?=0
    rommon 19 > tftpdnld [ur]
    usage: tftpdnld [-hr]
      Use this command for disaster recovery only to recover an image via TFTP.
      Monitor variables are used to set up parameters for the transfer.
      (Syntax: "VARIABLE_NAME=value" and use "set" to show current variables.)
      "ctrl-c" or "break" stops the transfer before flash erase begins.
      The following variables are REQUIRED to be set for tftpdnld:
                IP_ADDRESS: The IP address for this unit
            IP_SUBNET_MASK: The subnet mask for this unit
           DEFAULT_GATEWAY: The default gateway for this unit
               TFTP_SERVER: The IP address of the server to fetch from
                 TFTP_FILE: The filename to fetch
      The following variables are OPTIONAL:
              TFTP_VERBOSE: Print setting. 0=quiet, 1=progress(default), 2=verbose
          TFTP_RETRY_COUNT: Retry count for ARP and TFTP (default=18)
              TFTP_TIMEOUT: Overall timeout of operation in seconds (default=7200)
             TFTP_CHECKSUM: Perform checksum test on image, 0=no, 1=yes (default=1)
              TFTP_MACADDR: The MAC address for this unit
                   FE_PORT: 0= (default), 1
             FE_SPEED_MODE: 0=10/hdx, 1=10/fdx, 2=100/hdx, 3=100/fdx,
                            5=Auto (default)
          TFTP_DESTINATION: The flash destination device for the file
                            flash:(default), usbflash0:, usbflash1:
      Command line options:
       -h: this help screen
       -r: do not write flash, load to DRAM only and launch image
    rommon 20 > tftpdnld
              IP_ADDRESS: 10.0.0.3
          IP_SUBNET_MASK: 255.0.0.0
         DEFAULT_GATEWAY: 10.0.0.1
             TFTP_SERVER: 10.0.0.2
               TFTP_FILE: c2800nm-adventerprisek9-mz.124-24.T4
            TFTP_VERBOSE: Progress
        TFTP_RETRY_COUNT: 18
            TFTP_TIMEOUT: 7200
           TFTP_CHECKSUM: No
            TFTP_MACADDR: 30:37:a6:49:35:a8
                 FE_PORT: Fast Ethernet 0
           FE_SPEED_MODE: Auto
    Invoke this command for disaster recovery only.
    WARNING: all existing data in all partitions on flash: will be lost!
    Do you wish to continue? y/n:  [n]:  y
    ARP: address resolution for 10.0.0.2 timed out.
    ARP failed with failure code 1.  TFTP transfer aborted.
    TFTP: Operation terminated prematurely.
    rommon 21 >

    What I notice in the original post is this error
    ARP: address resolution for 10.0.0.2 timed out.
    which says that the router is looking for the 10.0.0.2 server but not getting response to its arp request. Can the original poster clarify for us how the device that has the image file is connected to the router that has the problem? Also what kind of device is 10.0.0.2? Is it a PC running TFTP server software or is it something else?
    HTH
    Rick

  • Virus scan server error: "No virus scan profile is selected as the "default"

    Hi Team,
    I  try to upload Fiori Code into SAP Netweaver Gateway server .
    i can able to share Project.
    But when i try to submit code
    then at the end of Process i got error message.
    Virus scan server error: "No virus scan profile is selected as the "default"
    Please Guide me
    Regards
    Pankaj Kamble
    Tags edited by: Michael Appleby

    Hi Abraham,
                 Thank you very much. My problem resolved.
    I  have one Query Please guide me.
    whenever  we run Server URL from The  Browser,   first we must need run    "chrome.exe --args --disable-web-security"  command on   CMD.   on located directory the Chrome has installed.
    to disable  web security.
    if I did not run that command on CMD,  then Fiori Apps not worked.
    Why it's compulsory to disable web security.
    Regards,
    Pankaj Kamble

  • HT201210 I attempted to install iOS 7.0.2 on my iPad (3rd gen).  The screen has frozen.  Have tried resetting and restoring (via iTunes).  Error mssg says that my iPad cannot be restored.  Now what do I do?

    I attempted to install iOS 7.0.2 on my iPad (3rd gen).  The screen has frozen.  Have tried resetting and restoring (via iTunes).  Error mssg says that my iPad cannot be restored.  Now what do I do?

    Hi there hhcd92!
    I have an article here for you that can help guide you through troubleshooting this situation:
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    Thanks for coming to the Apple Support Communities!
    Regards,
    Braden

  • Error: process-uri-objects reports: HTTP2020: cannot find template default

    Error
    process-uri-objects reports: HTTP2020: cannot find template default
    Migrated from v4 to 6 but getting this error.

    Here is the obj.conf from migrated SSL server 6.0 sp5
    $ more obj.conf
    # Netscape Communications Corporation - obj.conf
    # You can edit this file, but comments and formatting changes
    # might be lost when the admin server makes changes.
    <Object name="weblogic" ppath="*/ts/*">
    Service fn="wl-proxy" WebLogicCluster="xxx.xxx.x.xx:yyyy,xxx.xxx.x.xx:yyyy" PathTrim="/ts" ErrorPage="htt
    p://ips.chase.com/Xcelerate/wlNotUp.html"
    </Object>
    <Object name="weblogic" ppath="*/jbs/*">
    Service fn="wl-proxy" WebLogicCluster="xxx.xxx.x.xx:yyyy,xxx.xxx.x.xx:yyyy" PathTrim=""
    </Object>
    <Object name="si" ppath="*/servletimages/*">
    Service fn="wl-proxy" WebLogicCluster="xxx.xxx.x.xx:yyyy,xxx.xxx.x.xx:yyyy"
    NameTrans fn="NSServletNameTrans" name="servlet"
    NameTrans fn="pfx2dir" from="/servlet" dir="/opt/netscape/servers/docs/servlet" name="ServletByExt"
    NameTrans fn="pfx2dir" from="/manual" dir="/opt/netscape/servers/manual/https" name="es-internal"
    NameTrans fn="pfx2dir" from="/ns-icons" dir="/opt/netscape/servers/ns-icons" name="es-internal"
    NameTrans fn="pfx2dir" from="/mc-icons" dir="/opt/netscape/servers/ns-icons" name="es-internal"
    NameTrans fn="pfx2dir" from="/help" dir="/opt/netscape/servers/manual/https/ug" name="es-internal"
    NameTrans fn="pfx2dir" from="/ns-icons" dir="/opt/netscape/servers/ns-icons" name="es-internal"
    NameTrans fn="pfx2dir" from="/mc-icons" dir="/opt/netscape/servers/ns-icons" name="es-internal"
    NameTrans fn="pfx2dir" from="/help" dir="/opt/netscape/servers/manual/https/ug" name="es-internal"
    NameTrans fn="pfx2dir" from="/cgi-bin" dir="/opt/netscape/suitespot/docs/cgi-bin" name="cgi"
    NameTrans fn=document-root root="$docroot"
    PathCheck fn="unix-uri-clean"
    PathCheck fn="check-acl" acl="default"
    PathCheck fn="find-pathinfo"
    PathCheck fn="find-index" index-names="index.html,home.html"
    ObjectType fn="type-by-extension"
    ObjectType fn="force-type" type="text/plain"
    Service method="(GET|HEAD|POST|PUT)" type="text/jsp" fn="wl-proxy" WebLogicCluster="xxx.xxx.x.xx:yyyy,xxx.xxx.x.xx:yyyy"
    Service method="(GET|HEAD)" type="magnus-internal/imagemap" fn="imagemap"
    Service method="(GET|HEAD)" type="magnus-internal/directory" fn="send-error"
    Service method="(GET|HEAD)" type="*~magnus-internal/*" fn="send-file"
    AddLog fn="flex-log" name="access"
    </Object>
    <Object name="cgi">
    ObjectType fn="force-type" type="magnus-internal/cgi"
    Service fn=send-cgi user="$user" group="$group" chroot="$chroot" dir="$dir" nice="$nice"
    </Object>
    </Object>
    <Object name="maintpwreset" ppath="*/maintpwreset/*">
    Service fn="wl-proxy" WebLogicHost="xxx.xxx.x.xx" WebLogicPort="yyyy"
    </Object>
    <Object name="pwreset" ppath="*/pwreset/*">
    Service fn="wl-proxy" WebLogicHost="xxx.xxx.x.xx" WebLogicPort="yyyy"
    </Object>
    <Object name="servlet">
    ObjectType fn=force-type type=text/html
    Service fn="NSServletService"
    </Object>
    <Object name="jsp092">
    ObjectType fn="type-by-extension"
    ObjectType fn="change-type" type="magnus-internal/jsp092" if-type="magnus-internal/jsp"
    Service fn="NSServletService" type="magnus-internal/jsp092"
    </Object>
    <Object name="ServletByExt">
    ObjectType fn=force-type type=magnus-internal/servlet
    Service type="magnus-internal/servlet" fn="NSServletService"
    </Object>
    <Object name="es-internal">
    PathCheck fn="check-acl" acl="es-internal"
    </Object>
    $
    Back end is a weblogic cluster, I have used xxx at place of IP and yy for port.
    Here is last few config lines from magnus.conf
    Init fn="load-modules" shlib="/opt/netscape/servers/bin/https/lib/libNSServletPlugin.so" funcs="NSServlet
    EarlyInit,NSServletLateInit,NSServletNameTrans,NSServletService" shlib_flags="(global|now)"
    Init fn="NSServletEarlyInit" EarlyInit=yes
    Init fn="NSServletLateInit" LateInit=yes
    Init fn="flex-init" access="/opt/netscape/servers/https-secure-xxxxxxx/logs/access" format.access="%Ses
    ->client.ip% - %Req->vars.auth-user% [%SYSDATE%] \"%Req->reqpb.clf-request%\" %Req->srvhdrs.clf-status% %
    Req->srvhdrs.content-length%"
    Init fn="load-types" mime-types="mime.types"
    Init fn="load-modules" funcs="wl-proxy,wl-init" shlib="/weblogic/lib/solaris/libproxy.so"
    Init fn="wl-init"
    Thanks

  • Factory reset for cisco ip phone 7980

    I am having issues finding documentation on how to wipe/reset the cisco 7980 video phone.
    Could someone provide instructions?

    I am guessing you meant 7985:
    Press **# in order to unlock Network Configuration on the phone.
    Press Settings.
    Press 3 on the keypad (or scroll down) for Network Configuration.
    Press 33 on the keypad (or scroll down) for Erase Configuration.
    Press the Yes softkey.
    Press the Save softkey
    Please rate useful posts.

  • Kernel[0]: (default pager): [KERNEL]: Swap File Error.

    Hello,
    I am hoping that I can get some help in understanding what might have gone wrong here to create the mass hanging of many apps as depicted in the attached image below.
    This is what I pulled from the logs:
    Sep 11 08:47:10 steve kernel[0]: (default pager): [KERNEL]: ps_select_segment - send HI_WAT_ALERT
    Sep 11 08:47:10 steve kernel[0]: low swap: suspending pid 622 (Adobe Photoshop )
    Sep 11 08:47:10 steve kernel[0]: (default pager): [KERNEL]: Swap File Error.
    Sep 11 08:47:14 steve com.apple.launchd[1] (com.apple.sleepservicesd[12240]): Exited: Killed: 9
    Sep 11 08:47:14 steve kernel[0]: memorystatus_thread: idle exiting pid 12240 [SleepServicesD]
    Sep 11 08:47:14 steve com.apple.launchd[1] (com.apple.xpcd.0A040000-0000-0000-0000-000000000000[12237]): Exited: Killed: 9
    Sep 11 08:47:14 steve kernel[0]: memorystatus_thread: idle exiting pid 12237 [xpcd]
    Sep 11 08:47:16 steve kernel[0]: (default pager): [KERNEL]: ps_select_segment - send HI_WAT_ALERT
    Sep 11 08:47:16 steve kernel[0]: (default pager): [KERNEL]: Swap File Error.
    Sep 11 08:47:16 steve kernel[0]: (default pager): [KERNEL]: ps_select_segment - send HI_WAT_ALERT
    Sep 11 08:47:16 --- last message repeated 2 times ---
    Sep 11 08:47:16 steve kernel[0]: (default pager): [KERNEL]: Switching ON Emergency paging segment
    Sep 11 08:47:18 steve kernel[0]: Sandbox: sandboxd(12246) deny mach-lookup com.apple.coresymbolicationd
    Sep 11 08:47:19 steve.local sandboxd[12246] ([12245]): fontworker(12245) deny file-read-data /Volumes/Users/Users/steve/Library/Preferences/ByHost/.GlobalPreferences.7FC032 09-A3F5-5B8F-ADA4-A2EA48544DC8.plist
    Sep 11 08:47:19 steve.local sandboxd[12246] ([12245]): fontworker(12245) deny file-read-data /Volumes/Users/Users/steve/Library/Preferences/.GlobalPreferences.plist
    Sep 11 08:47:19 steve.local sandboxd[12246] ([12245]): fontworker(12245) deny file-read-data /Volumes/Users/Users/steve/.CFUserTextEncoding
    Sep 11 08:48:07 steve com.apple.launchd[1] (com.apple.sleepservicesd[12243]): Exited: Killed: 9
    Sep 11 08:48:07 steve kernel[0]: memorystatus_thread: idle exiting pid 12243 [SleepServicesD]
    Sep 11 08:48:08 steve kernel[0]: ]: ps_allocate_cluster - send HI_WAT_ALERT
    Sep 11 08:48:08 steve kernel[0]: (default pager): [KERNEL]: ps_allocate_cluster - send HI_WAT_ALERT
    Sep 11 08:48:09 --- last message repeated 403 times ---
    Sep 11 08:48:09 steve kernel[0]: nd HI_WAT_ALERT
    Sep 11 08:48:09 steve kernel[0]: (default pager): [KERNEL]: ps_allocate_cluster - send HI_WAT_ALERT
    Sep 11 08:48:39 --- last message repeated 171 times ---
    Sep 11 08:49:04 steve.local fseventsd[36]: SLOWDOWN: client 0x7fd92b015e00 (pid 622) sleeping due to too many errors (num usleeps 21)
    Sep 11 08:49:17 steve kernel[0]: Sandbox: sandboxd(12256) deny mach-lookup com.apple.coresymbolicationd
    Sep 11 08:49:18 steve.local sandboxd[12256] ([12255]): fontworker(12255) deny file-read-data /Volumes/Users/Users/steve/Library/Preferences/ByHost/.GlobalPreferences.7FC032 09-A3F5-5B8F-ADA4-A2EA48544DC8.plist
    Sep 11 08:49:18 steve.local sandboxd[12256] ([12255]): fontworker(12255) deny file-read-data /Volumes/Users/Users/steve/Library/Preferences/.GlobalPreferences.plist
    Sep 11 08:49:18 steve.local sandboxd[12256] ([12255]): fontworker(12255) deny file-read-data /Volumes/Users/Users/steve/.CFUserTextEncoding
    Sep 11 08:49:28 steve com.apple.launchd.peruser.89[451] (com.apple.cfprefsd.xpc.agent[12253]): Exited: Killed: 9
    Sep 11 08:49:28 steve kernel[0]: memorystatus_thread: idle exiting pid 12253 [cfprefsd]
    Sep 11 08:49:28 steve kernel[0]: (default pager): [KERNEL]: System is out of paging space.
    Sep 11 08:49:28 steve kernel[0]: (default pager): [KERNEL]: ps_allocate_cluster - send HI_WAT_ALERT
    Sep 11 08:49:28 steve kernel[0]: low swap: suspending pid 7864 (Microsoft PowerP)
    Sep 11 08:49:28 steve kernel[0]: low swap: suspending pid 658 (Google Chrome)
    Sep 11 08:49:28 steve kernel[0]: (default pager): [KERNEL]: Swap File Error.
    Sep 11 08:49:28 steve kernel[0]: (default pager): [KERNEL]: ps_allocate_cluster - send HI_WAT_ALERT
    Sep 11 08:49:29 --- last message repeated 8 times ---
    Sep 11 08:49:29 steve kernel[0]: te_cluster - send HI_WAT_ALERT
    Sep 11 08:49:29 steve kernel[0]: (default pager): [KERNEL]: ps_allocate_cluster - send HI_WAT_ALERT
    Sep 11 08:49:34 --- last message repeated 224 times ---
    Sep 11 08:49:34 steve.local QuickLookUIHelper[12258]: [QL] QuickLookUIHelper is stuck - force quit now
    Sep 11 08:50:02 steve.local fseventsd[36]: SLOWDOWN: client 0x7fd92e809400 (pid 593) sleeping due to too many errors (num usleeps 42)
    Sep 11 08:50:02 steve.local fseventsd[36]: SLOWDOWN: client 0x7fd92e805400 (pid 1988) sleeping due to too many errors (num usleeps 42)
    Sep 11 08:51:07 steve.local fseventsd[36]: SLOWDOWN: client 0x7fd92b015e00 (pid 622) sleeping due to too many errors (num usleeps 75)
    Other notes that might help yuo help me.
    Machine is an iMac with 16gig of RAM.
    There are two partitions on the drive... one for the OS and one for users.
    The OS has an 80gig Partition with 50% free space.
    The User partition is much more with about 75% free space.
    In the past I have noticed Photoshop to be using over 8gig of RAM so maybe it is photoshop.
    Thanks
    Morgs

    There is excessive swapping of data between physical memory and virtual memory. That can happen for two reasons:
    You have a long-running process with a memory leak (i.e., a bug), or
    You don't have enough memory installed for your usage pattern.
    Tracking down a memory leak can be difficult, and it may come down to a process of elimination.
    When you notice the swap activity, open the Activity Monitor application and select All Processes from the menu in the toolbar, if not already selected. Click the heading of the Real Mem column in the process table twice to sort the table with the highest value at the top. If you don't see that column, select
    View ▹ Columns ▹ Real Memory
    from the menu bar.
    If one process (excluding "kernel_task") is using much more memory than all the others, that could be an indication of a leak. A better indication would be a process that continually grabs more and more real memory over time without ever releasing it. Here is an example of how it's done.
    The process named "Safari Web Content" renders web pages for Safari and other applications. It uses a lot of memory and may leak if certain Safari extensions or third-party web plugins are installed. Consider it a prime suspect.
    If you don't have an obvious memory leak, your options are to install more memory (if possible) or to run fewer programs simultaneously.
    The next suggestion is only for users familiar with the shell. For a more precise, but potentially misleading, test, run the following command: 
    sudo leaks -nocontext -nostacks process | grep total
    where process is the name of a process you suspect of leaking memory. Almost every process will leak some memory; the question is how much, and especially how much the leak increases with time. I can’t be more specific. See the leaks(1) man page and the Apple developer documentation for details.

  • Problem Cisco Catalyst 3850 input errors

    Ive installed two stacked Catalyst 3850s. Connected to these two switches I have a SAN 6210 Equallogic Dell ESX .
    The interfaces on the switches  is bundels with Port-channel. MTU size 9198. On swich one its no problem but on switch two I see input errors on these interface.
    If I move the cables from switch two to one then its ok...
    I have two 10G going to the SAN. And 4 ESX server with 2 ISCSI each.
    interface Port-channel21
     description ESX1 ISCSI SAN
     switchport access vlan 21
     switchport mode access
     flowcontrol receive desired
     spanning-tree portfast
     spanning-tree bpduguard enable
    Port-channel21 is up, line protocol is up (connected)
      Hardware is EtherChannel, address is 
      Description: ESX1 ISCSI SAN
      MTU 9198 bytes, BW 2000000 Kbit/sec, DLY 10 usec,
         reliability 255/255, txload 17/255, rxload 16/255
      Encapsulation ARPA, loopback not set
      Keepalive set (10 sec)
      Full-duplex, 1000Mb/s, link type is auto, media type is
      input flow-control is off, output flow-control is unsupported
      Members in this channel: Gi1/0/25 Gi1/0/34
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input 00:07:12, output never, output hang never
      Last clearing of "show interface" counters 1d21h
      Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/40 (size/max)
      5 minute input rate 128760000 bits/sec, 8233 packets/sec
      5 minute output rate 137021000 bits/sec, 7343 packets/sec
         520088013 packets input, 1454135312 bytes, 0 no buffer
         Received 1088 broadcasts (0 multicasts)
         0 runts, 0 giants, 0 throttles
         1534 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 watchdog, 0 multicast, 0 pause input
         0 input packets with dribble condition detected
         564793180 packets output, 978716517 bytes, 0 underruns
         0 output errors, 0 collisions, 0 interface resets
         0 unknown protocol drops
         0 babbles, 0 late collision, 0 deferred
         0 lost carrier, 0 no carrier, 0 pause output
         0 output buffer failures, 0 output buffers swapped out

    Hi and Sorry Just copied and past the part that I thought  was the problem. It seems that MTU size on switch two in the stack still has MTU 1500......
    So here is the lot....
    This interface is OK
    sh controllers ethernet-controller g1/0/25
    Transmit                  GigabitEthernet1/0/25                 Receive
    2373084674113 Total bytes               2700589618458 Total bytes
       1259517537 Unicast frames               1355829627 Unicast frames
    2373055994149 Unicast bytes             2700589410330 Unicast bytes
           314726 Multicast frames                      0 Multicast frames
         25604588 Multicast bytes                       0 Multicast bytes
            44657 Broadcast frames                   3252 Broadcast frames
          3075376 Broadcast bytes                  208128 Broadcast bytes
                0 System FCS error frames               0 IpgViolation frames
                0 MacUnderrun frames                    0 MacOverrun frames
                0 Pause frames                          0 Pause frames
                0 Cos 0 Pause frames                    0 Cos 0 Pause frames
                0 Cos 1 Pause frames                    0 Cos 1 Pause frames
                0 Cos 2 Pause frames                    0 Cos 2 Pause frames
                0 Cos 3 Pause frames                    0 Cos 3 Pause frames
                0 Cos 4 Pause frames                    0 Cos 4 Pause frames
                0 Cos 5 Pause frames                    0 Cos 5 Pause frames
                0 Cos 6 Pause frames                    0 Cos 6 Pause frames
                0 Cos 7 Pause frames                    0 Cos 7 Pause frames
                0 Oam frames                            0 OamProcessed frames
                0 Oam frames                            0 OamDropped frames
           423237 Minimum size frames               78563 Minimum size frames
        593742624 65 to 127 byte frames         338414660 65 to 127 byte frames
          1416083 128 to 255 byte frames          4836098 128 to 255 byte frames
           558097 256 to 511 byte frames          1505992 256 to 511 byte frames
          5464138 512 to 1023 byte frames         6457219 512 to 1023 byte frames
        472854085 1024 to 1518 byte frames      834470341 1024 to 1518 byte frames
            80781 1519 to 2047 byte frames         257961 1519 to 2047 byte frames
          2891352 2048 to 4095 byte frames       13701476 2048 to 4095 byte frames
         14353508 4096 to 8191 byte frames        8698824 4096 to 8191 byte frames
        168093015 8192 to 16383 byte frames     147411745 8192 to 16383 byte frames
                0 16384 to 32767 byte frame             0 16384 to 32767 byte frame
                0 > 32768 byte frames                   0 > 32768 byte frames
                0 Late collision frames                 0 SymbolErr frames
                0 Excess Defer frames                   0 Collision fragments
                0 Good (1 coll) frames                  0 ValidUnderSize frames
                0 Good (>1 coll) frames                 0 InvalidOverSize frames
                0 Deferred frames                       0 ValidOverSize frames
                0 Gold frames dropped                   0 FcsErr frames
                0 Gold frames truncated
                0 Gold frames successful
                0 1 collision frames
                0 2 collision frames
                0 3 collision frames
                0 4 collision frames
                0 5 collision frames
                0 6 collision frames
                0 7 collision frames
                0 8 collision frames
                0 9 collision frames
                0 10 collision frames
                0 11 collision frames
                0 12 collision frames
                0 13 collision frames
                0 14 collision frames
                0 15 collision frames
                0 Excess collision frames
    LAST UPDATE 4870 msecs AGO
    This interface have problem. It is in portchannel with g1/0/25. Ive got more interfaces and port-channels showing the same behavior for switch two in my cluster.
    sh controllers ethernet-controller g2/0/25
    Transmit                  GigabitEthernet2/0/25                 Receive
     925460044357 Total bytes                201085804055 Total bytes
        702370104 Unicast frames                184041790 Unicast frames
     925449913241 Unicast bytes              201085599895 Unicast bytes
           118823 Multicast frames                      0 Multicast frames
          9171804 Multicast bytes                       0 Multicast bytes
            14251 Broadcast frames                   3190 Broadcast frames
           959312 Broadcast bytes                  204160 Broadcast bytes
                0 System FCS error frames               0 IpgViolation frames
                0 MacUnderrun frames                    0 MacOverrun frames
                0 Pause frames                          0 Pause frames
                0 Cos 0 Pause frames                    0 Cos 0 Pause frames
                0 Cos 1 Pause frames                    0 Cos 1 Pause frames
                0 Cos 2 Pause frames                    0 Cos 2 Pause frames
                0 Cos 3 Pause frames                    0 Cos 3 Pause frames
                0 Cos 4 Pause frames                    0 Cos 4 Pause frames
                0 Cos 5 Pause frames                    0 Cos 5 Pause frames
                0 Cos 6 Pause frames                    0 Cos 6 Pause frames
                0 Cos 7 Pause frames                    0 Cos 7 Pause frames
                0 Oam frames                            0 OamProcessed frames
                0 Oam frames                            0 OamDropped frames
           155980 Minimum size frames                3226 Minimum size frames
         92357460 65 to 127 byte frames          52503630 65 to 127 byte frames
           542363 128 to 255 byte frames           660137 128 to 255 byte frames
          1843346 256 to 511 byte frames           500600 256 to 511 byte frames
          6158096 512 to 1023 byte frames         1116353 512 to 1023 byte frames
        601445933 1024 to 1518 byte frames      129261034 1024 to 1518 byte frames
                0 1519 to 2047 byte frames         319527 1519 to 2047 byte frames
                0 2048 to 4095 byte frames              0 2048 to 4095 byte frames
                0 4096 to 8191 byte frames              0 4096 to 8191 byte frames
                0 8192 to 16383 byte frames             0 8192 to 16383 byte frames
                0 16384 to 32767 byte frame             0 16384 to 32767 byte frame
                0 > 32768 byte frames                   0 > 32768 byte frames
                0 Late collision frames                 0 SymbolErr frames
                0 Excess Defer frames                   0 Collision fragments
                0 Good (1 coll) frames                  0 ValidUnderSize frames
                0 Good (>1 coll) frames            319524 InvalidOverSize frames
                0 Deferred frames                       3 ValidOverSize frames
                0 Gold frames dropped                   0 FcsErr frames
                0 Gold frames truncated
                0 Gold frames successful
                0 1 collision frames
                0 2 collision frames
                0 3 collision frames
                0 4 collision frames
                0 5 collision frames
                0 6 collision frames
                0 7 collision frames
                0 8 collision frames
                0 9 collision frames
                0 10 collision frames
                0 11 collision frames
                0 12 collision frames
                0 13 collision frames
                0 14 collision frames
                0 15 collision frames
                0 Excess collision frames

  • C5550 -How do I reset a persistant "Clear paper Jamm" error mesage?

    Hi,
    I have a photosmart c5550 all in one printer. I had a paper jam and cleared it using the instructions from the user manual. I have actually done this several times now, and am absolutely sure that there is no paper jam at this point in time. The printer resets to the "clear paper jam" error state on power up. I would like to know the procedure to do a hard system reset, to reset the printer. The reset procedure of removoing the power cord does nothing to clear this persistant error. Does anyone know the proper procedure to do a hard reset?
    Thanks,
    Phil

    The steps in this video will resolve persistant paper jam messages.
    I am an HP employee.

  • Cisco ids 4235 setup error

    When I telnet to one of my sensors, I ran setup, I got the following error, please help.
    Error: XML Parser: no element found at line 1

    I get the same error when I try to update the signature in my IDS:
    "An error occurred while running the update script on the sensor named VDG4235-ISP01. Detail = CLI Error: "XML Parser: no element found at line 1"
    1. What can I do?
    In addition, those errors are showed when I do this:
    VDG4235-ISP01# sho tls fingerprint
    Error: FileHelper load error: not a file [/usr/cids/idsRoot/etc/cert/default.cer]
    VDG4235-ISP01# sho tls trusted-hosts
    Error: XML Parser: no element found at line 1
    VDG4235-ISP01#

  • Trying to put movies back on my iPod touch 2, I had to reset it, now I keep getting error messages?

    Trying to put movies back on my iPod touch 2, I had to reset it, now I keep getting error messages?

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reboot the computer
    - Try another USB port and cable
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Restore from backup. See:                                 
    iOS: How to back up                             
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar                       

  • Have reset password but then get an error message 1004

    after resetting password keep getting message saying error 1004,can anyone help work this out?

    For general advice see Troubleshooting issues with iTunes for Windows updates.
    The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
    Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
    tt2

Maybe you are looking for