Reset hub and now getting extremely slow speeds...
Hi there,
So I have had bt broadband for 3 months and had nothing but problems. The speed is very slow, though I do live in a rural area so somewhat to be expected. However in the evenings I have noticed I can get extremely high pings (1000+) and slow speeds (below 0.5 mbps).
Recently however my usual daytime speeds of around 1.2 mbps shot up to around 3 mbps, which to me is quite high! (compared to what I have been getting).
Though it dropped off a bit over the past few days (to around 2.2 mbps) it was still working ok, until last night when I reset my homehub as my sister was unable to connect to it at all.
Since then I have had nearly none existant speeds. Even getting on here was a mission. I am getting speeds of around 0.10 mbps, though my ping seems to vary wildly from around 50 all the way back up to silly numbers.
I attempted to use the bt speed test, but it told me it couldn't get a reading cos my line was too slow!
I did however get one eventually from BT wholesale as below. (it won't let me copy it in?...)
Download speed (mbps): 0.14
Upload speed (mbps): 0.35
Ping Latency (ms): 69.63
Speedtest.net give the following
Really getting fed up with the unreliable and slow connection. When added to the problems getting a line installed in the first place (it took 3 months!) and problems I have had in the past, I am seriously looking to see what other options I have, but there aren't many good providers that will set us up out here
Can anyone help me get a stable, reasonably fast connection?
Thanks,
Richard
Hi,
Here are the adsl stats
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 01:19:52
Downstream:
512 Kbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
38.7 dB / 17.0 dB
Line attenuation (Down/Up):
14.4 dB / 8.0 dB
Output power (Down/Up):
17.6 dBm / 12.3 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
1 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 0
Error Seconds (Local/Remote):
1 / 0
I currently have the hub connected to the master socket via a filter. I have tried on the main socket and master socket with two different filters and nothing changed...
As for the btspeedtester, I was unable to successfully run that...It just says my connection may be too slow (no kidding!)
Finally, regarding the quiet line test...I don't actually have a phone at the moment. I only wanted broadband as I rarely make phone calls from the house and use my mobile. I am looking to get one for the sole purpose of fixing this issue (and ringing bt to have a whinge at them)
Thanks,
Richard
Similar Messages
-
Switched to BT, now getting really slow speeds
Hi, I moved to BT yesterday from EE. I've noticed that since the switch over, my speed has fallen drastically. Whilst I didn't check speeds on the old EE connection (it was running fine with multiple devices logged in throughout peak times & I never had cause to check), it was definitely much quicker. Now I'm on BT, I can't download anything, or watch video on demand. I've even taken to checking all my e-mail on my iPhone because outlook seems to take forever now. I've done a speed check, and I'm getting 0.24MB wired, 0.20 wireless (next to router) and 0.18 wireless in another room. This was without any other device connected. Can anyone think of any reason for the dramatic fall in service from switching broadband provider and anything I can do to fix it? To save time, I'll mention that my phone socket does not have a test port. Also, in case this does not pan out, does anyone know if there is a 'cooling off period' in which I can cancel and return BT's router? Thanks, Harry
welcome to the BT community forum where customers help customers and only BT employees are the forum mods
in order for the forum members to help please can you post the adsl stats if HH4/5 then go to troubleshooting then logs and you are looking for 2 line together when hub last connected to internet and they will show your connection speed and noise margin or if netgear enter 192.168.0.1). Then run btspeedtester (MAC users may have problems). when first test completes then run diagnostic test and post the results ( do not reset the router).
Have you tried the quiet line test? - dial 17070 option 2 - should hear nothing - best done with a corded phone. if cordless phone you may hear a 'dull hum' which is normal
Someone may then be able to offer help/assistance/suggestions to your problem
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’. -
Extremely slow speeds on Windows Computers with 5th Generation AirPort Extreme
I just got a new refurbished AirPort Extreme 5th generation. Everything works great for all of my OS X devices and iOS Devices. I am getting my ISPs speeds when doing tests. The issue is when I am using Windows devices. My roommate has a desktop and a netbook and both are getting extremely slow speeds. Speeds like .07Mbps down. Does anyone have any idea what the issue might be?
You have no large file?? Really.. in the whole computer there is not a windows update file.. a backup file... a movie download file.. nothing.. ??
Anyway that is irrelevant.. the issue is wireless.
Download the latest drivers from the wireless manufacturer.
You will need to find out what wireless card is used and locate the correct download for that model.
On the Airport it is well worth doing the following tests.
1. Change the name to SMB standard.. short no spaces pure alphanumeric.
So if your wireless name is Fred Blog's Airport Extreme wireless
Plesae change it to AEwifi
2. Take off all security for a test.
3. Set channels.. I am guessing the computers are only using 2.4ghz, so set 11,6, 1 in that order.
No improvement.. just put the security back to WPA2 Personal with pure alphanumeric password..
Try and test new drivers and use no firewalls on the computer.. ensure that the computer is correctly set for home network.
Beyond that it is just incompatible. -
i have a airport extreme base station and i reset it and now the wifi connection is open to everyone... so how do i get a password back on it so everyone cant use it
Read the user guide:
http://support.apple.com/manuals/#airport -
I was given an iPhone 3G, reset it, and now have picture which I believe indicates I should connect to my computer and iTunes. Have done so, clicked download which was done, but nothing changes on the phone. I know I can only upgrade to ios 4.2 but how do I do this?
Hello challenged37,
From what you describe it sounds like the phone is in recovery mode. Try connecting the phone to the wall charger that it came with, and perform a reset then connect it to iTunes again and try:
Reset
You should reset your device as a last resort and only if you can't restart it.
To reset, press and hold both the Sleep/Wake and Home buttons for at least 10 seconds, until you see the Apple logo.
From: Turn your iOS device off and on (restart) and reset
http://support.apple.com/kb/ht1430
Here is some additional info on what to do if the device still doesnt show in iTunes from the article named:
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
If you see the Connect to iTunes screen but the device does not appear in iTunes, follow these troubleshooting steps if you're using a Mac, or these steps for Windows computers.
Thank you for using Apple Support Communities.
Cheers,
Sterling -
Macbook Pro gets Extremely slow when itunes is open
When I launch Itunes my mac gets extremely slow. I mean so slow that right now it is open and i am watching my words catch up to my typing. If I play a song on itunes my processor doesn't go about 40% and it is still extremely slow. I even tried to wirelessly sync my iphone and it still is like this. Any one know why. I have lion with all updates. If I don't launch itunes I'm fine When I launch Itunes It drags like a mother...lol any and all help appreciated TIA!!
How much free space on the startup disk?
Right or control click the MacintoshHD icon. Click Get Info. In the Get Info window you will see Capacity and Available. Make sure you have a minimum of 15% free disk space. -
Subscribed calendars - iPhone calendar gets extremly slow.
Hi, I tried to use subscribed calendars on iPhone. Due to the fact that there is still no brithday calendar implemented on iPhone I had to add several calendards:
1: brithday calendar - I published the iCal birthday calendar to mobile me.
2: calendar week - as there is still no ISO calendar week on iPhones CalApp I subscribed for a calendar with whole day events on every monday - showing the week number.
3: a friends calendar - A standard Google calendar
With these three subscriptions, my MobileMe calendar and my ActiveSync the CalApp on iPhone gets extremely slow. Does anybody else does have the same problems. Having a limit with not more than two subscribed calendars, app speed is slow but acceptable. Having just one subscribed calendar we can speak about normal behavior.You could reduce to 2 subscribed feeds by using a ISO calendar that is merged into an existing calendar in your .mac account instead of as a subscribed feed. Those numbered weeks aren't going to change, so why not just make permanent? I did the same thing in my Google calendar.
I have subscribed to 5 calendar feeds in iPhone 3.0 and have no speed performance issues. However, the calendar app only displays information for one of the subscribed feeds! I cannot get the other feeds to work. I have tried installing each one before and after the one working feed, but still they do not work. All the feeds work in iCal on my computer.
The 4 feeds that are not working properly on the iPhone are schedules to my favorite MLB, NFL and college teams from Yahoo! Sports. I want subscribed feeds because game times and t.v. listings change from week to week.
This is disappointing because subscribed calendar feeds was the major improvement I wanted to see in 3.0. -
I have recently changed my bt home hub and now my airport express won't connect to it? Any suggestions?
Anytime you change out a modem or modem router like the HomeHub, the AirPort Express needs to be reset back to factory default settings and then set up again.
The reason for this is that the Express is retaining some or all of the settings to connect to your "old" modem or hub, so it will not work correctly with a new device unless you start over again from factory default settings on the Express.
Power up the Express for a few minutes
Hold in the reset button on the side of the Exprsss for 8-10 seconds, then release and allow a full minute for the Express to restart to a slow, blinking amber light
Now, set up the Express again, like you did originally with the "old" modem or hub that you had previously. -
As the title says, I can't reinstall Mountain Lion. When I turn on the iMac, it send me straight to OX X Utilities. When I click on Reinstall Mountain Lion, it asks for my ID, but then states I did not purchase Mountain Lion. How do I fix this issue? I've tried asking Apple Support, but to no avail. I don't think the guy I spoke with understood what was going on.
I cannot get around OS X Utilities. There are only four options for me.
Reinstall Mountain Lion
Back Up (tried, nothing comes up)
Get Help Online (which is what I'm doing here)
Erase or Restore Utilities (I've checked this, it says my disks are not malfunctioning)
My friend suggested signing into his ID to reinstall but when we did, it also said this ID has not purchased Mountain Lion. We logged into Apple Support went to registed devices and there was nothing there. I think he may have used another ID which is he searching for the info for. If we get the right ID, then maybe it will let us sign in on his name and reinstall Mountain Lion. But if he can't, or Apple won't take his ID, then I'm at a loss for options.
So now I'm here, hoping someone else who bought a used iMac from a friend who factory reset it and needs info on how to reinstall Mountain Lion can help me. I don't know what else to do. If I can't get this thing sorted out, I'll have to drive to the apple store. The closest one is 60 miles away, so I'm not looking forward to that. Is that my only option now? What can I do?
tl;dr I bought a used iMac from a friend who factory reset it, and now I don't know how to reinstall Mountain Lion. What are my options?If the system didn't ship with Mountain Lion originally and you didn't purchase Mountain Lion yourself, then you will need to purchase. A purchase by the system's original owner cannot be transferred to you.
Unless you have another system on which you have purchased Mountain Lion, you will need to first install Mac OS X 10.6.8 on the iMac, for which you'll need either the original installation disks, if the iMac came with 10.6, or a retail copy of 10.6. Install 10.6 and upgrade to at least 10.6.6, and then you can buy Mountain Lion from the Mac App Store, presuming of course that the imac can support Mountain Lion. See:
http://www.apple.com/osx/how-to-upgrade/
Regards. -
After updating to ISO6, my email sending get extremely slow or dispeard. on the botton line of mail page always indicate "sending # of 9", however I do not know where to check or delete these unsent items. Please help! It has consumed lots of data.
I use @me.com and @hotmail.comHi,
>>A CHAR datatype and VARCHAR2 datatype are stored identically (eg: the word 'WORD' stored in a CHAR(4) and a varchar2(4) consume exactly the same amount of space on disk, both have leading byte counts).
Ok, but on the other hands:
SGMS@ORACLE10> create table x (name char(10), name2 varchar2(10));
Table created.
SGMS@ORACLE10> insert into x values ('hello','hello');
1 row created.
SGMS@ORACLE10> commit;
Commit complete.
SGMS@ORACLE10> select vsize(name),vsize(name2) from x;
VSIZE(NAME) VSIZE(NAME2)
10 5
SGMS@ORACLE10> select dump(name),dump(name2) from x;
DUMP(NAME) DUMP(NAME2)
Typ=96 Len=10: 104,101,108,108,111,32,32,32,32,32 Typ=1 Len=5: 104,101,108,108,111Cheers -
I upgraded to 9.01 of Firefox and now get an error 'MORZCRT19.dll" --
If you use ZoneAlarm Extreme Security then disable Virtualization and reinstall Firefox.
See these about a similar problem caused by ZoneAlarm.
*http://kb.mozillazine.org/Browser_will_not_start_up#XULRunner_error_after_an_update
*[[/questions/880050]] -
My MacBook Air running on Snow Leopard gets extremely slow (almost like a hang, except if you wait about half an hr, it actually moves) after login interface. Sometimes it never gets past the background of the homepage, desktop doesn't seem to load. After multiple forced shut downs and left to run for hours, sometimes the desktop loads but the dock does not respond when applications are opened. The computer is then unable to shut down normally. Forced shut downs are necessary most times. Time machine backup takes extremely long, and attempts to use the time machine to bring the laptop back to the time befiore the problem arose was met with extremely slow and hung time machine function.
Please help!There isn't much besides a failing hard drive or other hardware fault that can cause those symptoms. Run the Apple Hardware Test, or just take it to an Apple Store for testing.
-
Downloaded a file and now get random windows popping up
Downloaded a file from the net and now get random windows popping up
There is no need to download anything to solve this problem.
You may have installed the "VSearch" trojan, perhaps under a different name. Remove it as follows.
Malware is constantly changing to get around the defenses against it. The instructions in this comment are valid as of now, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for more recent discussions or start a new one.
Back up all data before proceeding.
Step 1
From the Safari menu bar, select
Safari ▹ Preferences... ▹ Extensions
Uninstall any extensions you don't know you need, including any that have the word "Spigot," "Trovi," or "Conduit" in the description. If in doubt, uninstall all extensions. Do the equivalent for the Firefox and Chrome browsers, if you use either of those.
Reset the home page and default search engine in all the browsers, if it was changed.
Step 2
Triple-click anywhere in the line below on this page to select it:
/Library/LaunchAgents/com.vsearch.agent.plist
Right-click or control-click the line and select
Services ▹ Reveal in Finder (or just Reveal)
from the contextual menu.* A folder should open with an item named "com.vsearch.agent.plist" selected. Drag the selected item to the Trash. You may be prompted for your administrator login password.
Repeat with each of these lines:
/Library/LaunchDaemons/com.vsearch.daemon.plist
/Library/LaunchDaemons/com.vsearch.helper.plist
/Library/LaunchDaemons/Jack.plist
Restart the computer and empty the Trash. Then delete the following items in the same way:
/Library/Application Support/VSearch
/Library/PrivilegedHelperTools/Jack
/System/Library/Frameworks/VSearch.framework
~/Library/Internet Plug-Ins/ConduitNPAPIPlugin.plugin
Some of these items may be absent, in which case you'll get a message that the file can't be found. Skip that item and go on to the next one.
This trojan is distributed on illegal websites that traffic in pirated content. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect much worse to happen in the future.
You may be wondering why you didn't get a warning from Gatekeeper about installing software from an unknown developer, as you should have. The reason is that this Internet criminal has a codesigning certificate issued by Apple, which causes Gatekeeper to give the installer a pass. Apple could revoke the certificate, but as of this writing, has not done so, even though it's aware of the problem. This failure of oversight has compromised both Gatekeeper and the Developer ID program. You can't rely on Gatekeeper alone to protect you from harmful software.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return. -
I got a blacklisted iphone 5 from att and I reset it and now when I try to set it up it needs a sim card so I went to the att store and they put a sim in and on the iPhone it says replacement needed couldn't complete activation.i just want use it as a ipod
To use it as an iPod it must be activated...to do that it has to accept a sim. A blacklisted iPhone cannot do that. Take it back to AT and T where you got it and get your money back.
-
I recently did the 5.3 update to my Apple TV and now it is running sluggish and things keep freezing and then pictures are loading on top of each other. Then I did a hard reset today and now the WWDC app is gone. Anyone else having these issues?
I have been having problems with my atv 3 not transmitting/receiving 5.1 surround. Whether I stream from my computer or watch movies, I am getting no 5.1 audio. The atv won't even show the option for surround. I tried to restore and reset the device but it didn't help.
I haven't had any problems with missing apps or freezing or anything similar to what you are experiencing. This update has many bugs. Other threads have reported even more problems. Hopefully I can go back to the previous update.
Maybe you are looking for
-
Lightroom 4 camera raw plugin 7.4 install questions
I have Lightroon 4 and CS4, When I right click to edit in CS4 I get a dialog box that says "This version of lightroom may require the Photoshop camera RAW plug-in version 7.4 for full compatibility. Any help?
-
I am trying to edit my pictures but everytime i try to clone the picture glitches or flickers. and when i crop the image turns black until i click it. every other tool works fine but these. i tried customer service but they suck and told me it's beca
-
Workflow for using Pages offline
How do I set up for this scenario. Have a Pages document in iCloud. Will be flying to Europe (no internet) so want to work on the document - and then when I arrive and have internet access want the new version to overwrite the old version. Any sugge
-
DMS integration with QM Notification
Hello, I have configured DMS screen in QM customizing and have created a DIR that I linked to a Quality Notification and attached an original file. My issue is that when I go to the Notification and select the Documents tab, the DMS documents do not
-
Keeping file names when rendering out DPX to QT
I am trying to convert a dpx sequence to a quicktime to use for offline editing. When I export the files it does not keep the original file name. It replaces the file name with 1_g1, 2_g1 and so on. I cannot find a way to tell color to keep the orgin