Reset- System shut down complete !

hi
i posted this in the german forum but nobody could help me ! :(
when my system was freezed or hanged, i pressed the reset button in order to reboot.
the result of rebooting was, the bios posted, then a short time black screen with cursor in the left upper corner and then the system turned off complete. ?(
i tryed a lot of thinks, bios changed, wake up jumper disabled on board and so on...
if you know a little german you can see it the whole problem
HERE
all that was before i installed 2 seperate HDDs on Raid. after the Raid 0 was build, windows installed on Raid, i can reboot now. but nobody knows why this problem happens by me !! ? ?
anyone had the same problem and can say me where the problem is/was ?
sorry for my bad english, im a little German

Hi,
You might try this (Ich habe die Deutse forum gelezen 8), don't write German back it's not allowed :P)
Take your CPU cooler off, clean it, regrease it with WHITE-paste and put it back on the right way as there is only 1 way the right one.....
Another thing can be spikes on the Cooler-RPM-wire, try another cooler and see what happens....

Similar Messages

My computer starts, bar completes half way and the system shuts down. Dont know what happened.

Starting abnormally, Like when I start my MacBook pro which is almost new. A bar runs on the white screen and then when it reached half way system shut down. Can anyone help. Any way to reset my computer.
Also, when I am going to option, the system doesn't allow me by saying hard disk is locked. Kindly help out

OS X- Gray progress bar appears under Apple logo during startup
I suggest you need to erase your drive and reinstall OS X. Be prepared for the possibility that your hard drive has failed.
Install or Reinstall Mavericks or Mountain Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
OS X Mavericks- Erase and reinstall OS X
OS X Mountain Lion- Erase and reinstall OS X
OS X Lion- Erase and reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.

System shut down during F110 payment run

During the F110 payment run, the PRD system shut down. There were 259 items in the proposal and according to the status 42 posting orders were generated and completed. What is the process to handle this problem? Can the payment run be re-started?
It appears that clearing documents were created for some open items before the system shut down but no checks are showing in the check register. Has this happened to anyone before and what steps should be taken to resolve this?

Is it a matter of...
1. deleting the output of the payment run,
2. deleting the proposal
3. canceling the the payment check by check using FCH8 if any occurred
4. reseting and reversing the clearing documents created using FBRA before the system shut down
5. start a new payment run

Mac Book Air shuts down completely if I close the cover and leave for hours. Message: you shut down your computer because of a problem. Any thoughts what is happening?

Mac Book Air shuts down completely if I close the cover and leave email running. Is n't it supposed to just sleep and awaken whe the cover is reopened? Instead, I have to boot it. Any idea what the problem is? I am unaware of any problem, just close the cover for safety.

Well I don't know anyone that closes the cove and leaves it for Hours... But try going to System Prefrences > Energy Saving > Uncheck Put Hard Disk to Sleep.

Premiere Pro CS4 crashes and system shuts down while rendering

Hi All,
Good morning everyone, my system shuts down while rendering using Adobe media encoder from premiere pro. I have tried the following:
1.Completely removing CS4 and reinstalling.
2. Updating all the video drivers.
3. Re installing the Operating System (XP and Vista)
But the issue persists, i have attached the crash report and any thoughts are highly appreciated.
Regards,
Vincent

A number of problems pop out of your DXDIAG:
Both your video driver and your audio driver are more than 3 years old.
Your F drive is slow, because of the fill rate of 90%. You lack other hard disks.
You have Matrox, BlackMagic, Nero, Sony, DivX and other stuff installed. It has been a long time ago that I have seen such a long list of DirectShow filters installed.
Suggestions: Update your drivers, clean up your F drive and add another disk, remove all that Matrox stuff, possibly include BlackMagic and Sony.
What export/encoding settings do you use from what sequence settings?

SYstem Shuts Down Every Time if on AC Power.

1. This does not happen if running on battery.
2. Lenovo suggested test seem to prove it is not a hardware problem --doesn't happen if on "F1" key.
3. Replaced power cord -no change
4. They think it could be defective Windows 7 Upgrade. Did not point to Virus. I have Virus protection.
5. Does not happen when booting up. Only when startup is complete and W7 Start screed is up.
6. Started happening a couple of months ago, at random, once a day. Now it goes black in just minutes, overtime.
7 W7 was installed bout six months ago. Was fine.
8 Can't reload W7 because Microsoft requires you to be on AC power to load.
9. If attempt to load from CD, system shuts down --goes black, complete shut down.

Hi, ttranfagli
I have a few questions so I can get a better grip on the issue at hand:
What is your machine type and model? Also, what do you mean by "if on "F1" key"? Also, have you tried this in Safe Mode? Finally, does this occur if the machine is running off of AC power only with the battery removed?
Thanks in advance,
Adam
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution!" This will help the rest of the community with similar issues identify the verified solution and benefit from it.

My ibook keeps shutting down completely with the date to reverting back to 1969. i restart only after i plug in charger it lets me, then change date and save. the next time i use same thing happens, safari, iphoto, email are the only ones i have used.

my ibook keeps shutting down completely with the date to reverting back to 1969. i restart only after i plug in charger it lets me, then change date and save. the next time i use same thing happens, safari, iphoto, email are the only ones i have used.
please help! i am at a loss here.
thank you, movie lady
ibook g4

The iBook does not have a backup (PRAM) battery. It only has the main battery and a small capacitor which maintains the settings long enough to do a battery swap. If the battery is dead, what you are seeing can happen.
If the battery is not a problem (or even if it is), you could try resetting the PMU and see if that helps.

My ipad2 shuts down completely after I press the sleep button and does not start.... Help please

My ipad2 shuts down completely after I press the sleep button and does not start.... Help please
This started since the latest update!!!!!!!!!!!!!!

Hi Alkaf,
Welcome to Apple Support Communities.
It sounds like your iPad will not turn on. Take a look at the iPhone article linked below, it provides tips that will help resolve power issues for both iPhones and iPads.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
-Jason

I have updated my ipad 2 and it has shut down completely and won't do anything ! Help

I have updated my ipad 2 and it has shut down completerly I can't even switch it. any ideas???

Try a reset:
1. Hold the Sleep and Home button down (together)
2. For about 10 seconds
3. Until you see the Apple logo (very important)
4. Ignore the red slider

My i mac shuts down completely often during the day. I have it set to sleep only late in the evening..I have OS10.6.8

My I mac shuts down completely often during the day. I have it set to go to sleep lay in the evening.
I ahve OS10.6.8

Hello,
Have you blown the dust out lately?
Get Temperature Monitor to see if it's heat related...
http://www.macupdate.com/info.php/id/12381/temperature-monitor
Open console in Applications>Utilities, check the system log for the date/time of the last problem & the Startup right after that for clues.

Windows 10 will not shut down completely? Power light stays on(official july 29th upgrade)

I just upgraded to windows 10 from windows eight and I'm facing shutdown problems because when I asked the PC to shut down; the screen goes off but the power light stays on and basically windows 10 does not shut down completely whenever I have to turn on my PC again, I have to force the power button down until it completely Shuts down and start it back up again.
I tried several troubleshooting tactics wants & browsed YouTube videos and but nothing seems work and I've seen people on this forum complain about same thing and am hoping HP fixes the problem.

YES!!!!! A Solution that worked. Spread the news. It has to do with the Intel Virtualization Tehnology. Didn't know what that was until this issue came up in Windows 10. First, find out if this is your issue. 1. I installed the 'Intel Processor Identification Utility' directly from Intel.2. After installation, open the program and go to the 'CPU Technologies' tab.3. If it says 'YES' for Intel Virtualization Tehnology, proceed. Solution...(at least on my system) 1. The next thing you have to do is go into the BIOS. If you have not done this before, proceed at your own risk. You need to restart the computer and enter the BIOS (for me I hit F10 at the HP screen)2. Within the BIOS, there is an 'Advanced Options' section3. In this section there is a line for 'Intel Virtualization Tehnology' and it will say enabled or disabled. My computer said disabled.4. If this is the case, change the option to 'ENABLED'; then SAVE and EXIT from the BIOS. The Computer will restart and from that point on Shut Down, Sleep, etc. has worked. WOW this was a frustrating issue. Almost went back to Windos 8. I take no credit for this solution, I pieced it together from other posts on this issue. Hope this helps.

I tried downloading the iOS8 to my iPod 5th generation and when it finished downloading it shut down completely and it said there was an error and no the iPod is in recovery mode. What can I do to restore it and update it? Please, I need help.

Hello,
I recently tried downloading the IOS8 to my iPod 5th generation and when it was almost done the computer said there was an error. Right after that, the iPod shut down completely and now it's on recovery mode. I plugged it in and it said that I had to restore it and update it so I could use it again but it doesn't let me. What can I do? I even did a backup before the update.
I really need help.

What happens when you connect to computer and restore via iTunes?
Without knowing that:
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Every so often a music app will pop and play and I can't closed it unless I shut down completely

Every so often on my IPhone 4 a music app will pop and play and I can't closed it unless I shut down completely. Why is this happening.

Every so often on my IPhone 4 a music app will pop and play and I can't closed it unless I shut down completely. Why is this happening.

Auto System Shut Down

Currently I am trying to put together a new computer. I have all the parts needed, and they are compatible. I put everything together, double/tripled checked all connections. when i try to turn it on, it runs for about 10 seconds, then just shuts off. ;( I'm running it bare, i have no monitor, keyboard, mouse, and sound connected. I just turned it on barebone.
I am using:
K7N2 Delta-L Motherboard
AMD 2800 Benton
2x 512 kingston Ram sticks
80gb 7200rpm hard drive
floppy
DVD drive
CD/RW drive
350watt enermax power supply
I have tried taking one of the ram sticks out and turning it on, it didn't work.
I tired getting a new 350watt antec power supply, it didn't work.
WHAT ELSE CAN I DO?!?! ?( ;(
Once again my problem is that the system shuts down automaticly after I turn it on. It will run for about 10 seconds then... it's down again.
PLEASE!! SOMEONE HELP!! ;(

CMOS is the chip that stores ya bios info like date, time and cpu settings etc.
It's the 3 pins bellow the small round silver battery.
On my K7N2-L (non Delta) it's jumper JBAT1
It as 2 settings 1 = keep data (normal use)
2 = clear data
look at following X = jumper position o = empty pin
Keep data
O
x
x
Clear data
x
x
o
after clearing cmos (do it with power off on PC or u will fry it) u will then need to setup bios again.
If this still wont boot have a look at jumpers J10 & J11
J10 sets cpu fsb mode
J11 sets cpu fsb frequency.
Look in ya manual it's in there.
Try to get PC to post by setting J11 to
J11 o J10 o
x o J10 not bridged = 100mhz
x
J11 safe mode cpu fsb 100mhz.
It will post then. Just the cpu will be set to a lower speed then it is.
If it posts go in to bios and hit set bios default then bridge J10 making it 133/166 mhz and J11 x
x
o this sets J11 to default 133
reboot and it should post good cpu speed.
Hope u understand all this junk i just wrote

Iphone 4s turns/shuts down completely for no known reason, why?

my new iphone 4s shut down completely...and only holding the home button and on/off button reboots the phone. but what causes it to automatically shut down to the point where itunes does not recognize the phone?

Ok, well thanks for confirming this.
I have two other questions...
I found this : '' If you're getting the unit fixed by Apple, be aware that you must have the original HD installed. If it's a third-party SSD or hybrid, Apple will tack $950 to the bill; if you don't have the original drive anymore, Apple will return your laptop unrepaired. ''
Is that true ? Because I actually have a hybrid HD and don't have the original...nor 950 $ ...
I found this information on : http://logicboardmac.blogspot.ca
Finally, I also found information about a flat rate repair option ?
http://nwsinglespeed.hubpages.com/hub/Do-You-Know-About-Apples-Flat-Rate-Repair- Pricing
Anyone knows anything about this ? Woud this apply to my macbook pro ?

Reset- System shut down complete !

Similar Messages

Maybe you are looking for