Reset TC with Original Settings after Power Failure

TC blinks yellow after power failure. How can I reset to original (before power failure) network settings?

Here you go: How to reset Time Capsule

Similar Messages

Problems With Starting Up After Power Failure

Hi Everyone,
I'm having the strangest problem booting up (or rather, not being able to boot up) after a power outage in my neighborhood last night. What's more, it's the second night in a row that it's happened and has blocked my ability to boot into my two main drives. I installed OSX on a separate internal drive so that I can access them and they seem to be all right and have all the information on them which is good.
Here's what happened: Two nights ago my computer was on and we had a power outage which turned my computer off, of course. I don't have it set to restart after something like this so I tried to restart it in the morning. The blue progress bar makes it about a quarter of the way across and stops. I have the same OS on another drive so I started up with the Option key and chose that and everything was fine. However, the next night the exact same thing happened and I couldn't boot into that drive the following morning either so I had to install a fresh version of OSX on another drive just to get into my computer. I've used Drive Utility, Drive Warrior, Drive Genius and TechTool Deluxe to check the drives and they all say there's nothing wrong. I've tried to reset the PRAM but still can't boot up into those drives which were on when we had the outage. I have unplugged everything and nothing else in the house seems to be effected. Any suggestions? I've had many power outages over the years with my Mac on but never have I ever experienced something like this, and on both drives too! As always, any help will be greatly appreciated and needless to say, I'm turning my computer off tonight before I go to bed!

Sounds like a lesson in there: don't wait to put OS X on an external drive that is usually off line.
Rush to a store or on-line and get a UPS of the 1500VA sort (APC RS would be nice, or SMART UPS 1000VA).
The directory of the drives could be corrupt.
I have all my equipment, modem, routers, the works, but we had a bad storm and one port on the router/modem is out (the one I used, the modem seems to be okay) and I am worried that the UPS's line filter for DSL in is also 'compromised.'
Storms and power outages can wRECK or cuase havoc.
It sounds like you need to map out bad sectors maybe (zero all in Disk Utility) perhaps. The directory, volume blocks, or even journal file, got scrambled. However, because no test can find it means - to me - it could be the "non user partitions" rather than OS X partition etc. Hence, zero the drive or just reformat it in full.
Why have you not ever with these outages, just continued to live w/o one? I wouldn't just shutdown, I would unplug if a storm approaches.
PS: SMC Reset button is under drive bay #4. Give it a 5-10 seconds depress.

HT1267 I need to reset my phone to it's original settings after backing it up, but it has been locked for months and I can NOT remember the password. What do I do??? It's an iPhone 4

I need to reset my phone to it's original settings after backing it up. It has been locked for several months and I do not remember the passcode. How do I do this??? HELP!!!

-Options for when an iOS device gets locked because of forgotten password-
Restore (and reset password) on your device by connecting it to the last computer to which it was connected:
iTunes: Backing up, updating, and restoring iOS software - http://support.apple.com/kb/HT1414
If you cannot connect it to the computer to which the device was last connected you will have to use recovery mode to completely reset the device, losing all data:
iOS: Unable to update or restore - http://support.apple.com/kb/HT1808 - recovery mode (e.g., cannot connect to computer last used to sync device)

TS1398 The wifi on my iPod doesn't work since upgrading the software to ios 6 therefore when I try to reset to the original settings I can't get my original software back. Can anyone help me with this?

The wifi on my iPod doesn't work since upgrading the software to ios 6 therefore when I try to reset to the original settings I can't get my original software back. Can anyone help me with this?

greeneygreeney wrote:
so you can't ever restore it to the factory settings? that is a big shame.
"It will ALWAYS restore to the lates available software.
You cannot downgrade."

Camera roll empty but shows 6.1 gb. Restored to original settings after backing up. When I restored the backup camera roll still shows 6.1 gb and is till empty. I imagine that the backup contains some corruption

Camera roll empty but shows 6.1 gb. Restored to original settings after backing up. When I restored the backup camera roll still shows 6.1 gb and is still empty. I imagine that the backup contains some corruption

Hi cfgolf,
Thanks for contacting Apple Support Communities. I agree with your assessment that something is going on with that previous backup. If you restored from that backup and the issue continues, I would recommend restoring and Set up as new. Before you restore, make sure you Transfer content so that you can sync it back after setting up as new. The instructions on how to Transfer content and Set up as new are both listed in this article.
iOS: How to back up your data and set up your device as a new device
http://support.apple.com/kb/ht4137
2. Transfer content
Before you erase your device, take a few minutes to transfer your content from your device to your computer to ensure that all your critical data is safe.
6. Set up as new
Complete the setup assistant. When prompted to set up your device, select Set Up as New iPhone and tap Next to continue.
Skip the Apple ID sign-in, in case the original issue was related to any of your content on iCloud.
Note: After setting up as new, you will need to enter the Visual Voicemail password for iPhone (on carriers that support Visual Voicemail). If you've forgotten the password, contact your carrier to help you reset it.
After erasing and setting up as a new device, your device is now in a factory configuration. Test to determine if erasing and setting up as a new device resolved the issue. Content on the device may have caused unexpected behavior.
If the issue is still present, you may want to contact Apple Support.
If the issue is now resolved, sync one type of content at a time back to the device. For example, if you had an issue playing music, add songs from iTunes and confirm they will play. If your contacts weren't loading successfully, add the contacts back. After each sync, test to see if the issue has returned.
Cheers,
-Joe

Domain controller VMs using dynamic VHDx corrupt after power failure

Over the past couple of months I have experienced 4 dead 2008 R2 SP1 domain controllers after power failure on Hyper-V 2012 hosts. The domain controller VMs will start after power failure and have varying degrees of file system corruption. In each instance
the corruption has rendered the domain controller unusable. The problem has not occurred with every power failure, but in testing the failure rate has been over 10%.
The Hyper-v 2012 hosts are as follows:
Dell PowerEdge r720 with flash backed write cache on Raid controller
Dell PowerEdge T710 with battery backed write cache on Raid controller
Dell PowerEdge T310 with a single SATA hard drive and write cache disabled
Generic system with a single SATA hard drive and write cache disabled
The VM configuration experiencing corruption is as follows:
Each VM was created from a base 2008 R2 SP1 syspreped VHDx image template file (40 Gigs)
The image template was originally created as a VHD and was then converted to a VHDx
The VHDx file has 512k sectors instead of the native 512e of VHDx files (a result of VHD - VHDx conversion)
Each VM was assigned 1024 Meg RAM and 1 virtual processor
The domain controllers were created by promoting the base 2008 r2 install to a DC after base image deployment
Only one corrupt VM was not running the 2012 integration components. The rest were running current 2012 integration components
I have done extensive testing on this issue and the problem for me seems to revolve around the VHDx file format. I have managed numerous Hyper-v installations since the original 2008 server version was released and I have never seen corruption like this
until 2012 and VHDx.
For the past few days I have been testing fixed sized VHD VMs on a 2012 host and I have not been able to reproduce the data corruption issue. I seem to only be able to reproduce the problem when using dynamic VHDx files. I have not done any testing on 2012
hosts with fixed size VHDx files or dynamic VHD files.
It would be great to hear from anybody else experiencing similar issues so that we can compare notes and hopefully get to the bottom of this problem.

To be honest I was excited to see this fix released, but there are two problems.
1. The hotfix causes BSOD if you have VLANs with a teamed NIC configuration. I found this out the hard way on a production system. How in the world did this thing get through testing and into automatic updates?
2. The hotfix does not seem to resolve the issue in my test environment.
I opened up a case with support and they informed me that they would not provide support for this issue and that I had to open a case with premier support. Premier support informed me that I cannot open a case with them unless I sign a $50,000 per year service
contract. Is there anywhere to get support on this issue?

RE1000 power light blinking after power failure

I've tried the 8 sec reset and the 30-30-30 reset but can't get the light to stop blinking and so can't connect to the unit. It was working fine before the power went out. Any suggestions?

I had the same issue after a power outage today. I online live chat with an agent for about 15 minutes until he provided me three options all about that I would have to pay extra to get it replaced or fixed because mine was just out of warranty yesterday. I was lucky enough because mine RE1000 was not dead completely. I followed the instructions in this community and restored its service successfully.
Here is what I did.
1. Reset the extender by 30-30-30 method. The LED still blinked after reset.
2. Turned off wifi on my laptop and assign a static IP on my laptop: 192.168.1.x. Ping RE's default gateway 192.168.1.1 with an Ethernet connection. It returned good result.
3. Log on Web Admin Page and I was prompted to upload its firmware. Followed the screen instruction to upload the firmware that I already downloaded previously. Waited until everything was finished and it rebooted. Volla. It was back to life.
I guess it might have lost the firmware somehow after power failure. Is there a battery inside the extender to power the flash rom?
Here are few instructions I followed up:
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=ca96fc48798d43489b4d16f9d77c14f9_Guidelines_in_Man...
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=25153
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=7e4956723e074191bdf33777314ddfd8_3998.xml&pid=80&r...
Cisco/Linksys/Berkin, you **bleep**. It is not that easy to rob my money what I earn by hard work.
Thanks for all advice and good luck.

Lenovo IdeaCentre Q180 behavior after power failure

Hi,
I need a computer which reboots itself after an power failure.
I didn't find anything about the behavior of the IdeaCentre Q180 in such case.
Does the IdeaCentre Q180 reboots itself after power failure or is it possible to enable this feature?
This behavior is very important for my new system.
Thank you for your answer.
Kind Regards,
Theodoor
Solved!
Go to Solution.

Hi theodoor, welcome to the forums,
I'm not personally aquainted with the Q180, but I had a look in the BIOS simulator and I'm pretty sure the function you're looking for is available in BIOS.
Please see attached picture, (too big to post), it will open in the same window so please click your browser back button to return to this site.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog
Attachments:
q180power.png ‏155 KB

Trouble booting up after power failure

After power failure(two hours), when booting up imac, just get a grey screen with blinking folder icon containing question mark.
I can hear clicking noise (hard drive?) that goes two or three clicks and then seems to give up.
How do I get it rebooted. Have disconnected and tried again with no result.

Sounds like the power failure may have fatally damaged the HD. Going forward use a UPS to protect your system, power surges can be very damaging to computers. You and try troubleshooting using Apple's Flashing question mark appears when you start your Mac but I think you may find the HD has failed. For confirmation you cal also run Apple Hardware Test in extended mode. Run AHT about 3x back to back and if it reports errors it's time to take the machine in for service.

How to configure V240 auto-boot after power failure?

Hi!
How to configure automatic boot of V240 machine after power failure? After power gets resored, V240 remains in standby mode and one has to press button on front to power it up. It is not convinient because power failure can occur, for example, at night and the machine is not booted until the first user awakens :)

Uhh... I've found publicly accessible document http://docs.sun.com/source/817-5481-11/variables.html :
Looks like this variable controls auto-power-up behaviour:
sc_powerstatememory
The sc_powerstatememory variable enables you to specify the state of the host server as false (keep the host server off) or true (return the server to the state it was in when the power was removed). This is useful in the event of a power failure, or if you physically move the server to a different location.
For example, if the host server is running when power is lost and the sc_powerstatememory variable is set to false, the host server remains off when power is restored. If the sc_powerstatememory variable is set to true, the host server restarts when the power is restored.
The values for this variable are as follows.
true - "Remembers" the state of the host server when power was removed and returns the server to that state when power is reapplied.
false - Keeps the server off when power is applied.

I tried to restore my iphone 5s but it shut off during the restore and wont turn back on I tried reseting it with the home and power button but it doesnt work and I tried connecting it to itunes but it doesnt show up

I tried to restore my iphone 5s but it shut off during the restore and wont turn back on I tried reseting it with the home and power button but it doesnt work and I tried connecting it to itunes but it doesnt show up

Did you try to connect in recovery mode, as explained in this article?
If you can't update or restore your iOS device
If this does not work, get it checked by an Authorized Apple Service Provider or by Apple:
iPhone - Contact Support - Apple Support

I have an iPhone 4S, and just now the sound quit working. It works with the headset and if I put it on speaker, but not anyway else. The music won't send sound out, the purine calls do the same. I reset to the original settings, nothing works.

I have an iPhone 4S, the sound quit working. I have sound in the headset and if I put the phone on speaker, I've reset to original settings, tried several options. Nothing works to resolve the options. Please help.

Hi there Wacjude,
I would recommend taking a look at the article below for some speaker and receiver troubleshooting steps.
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Hope that helps.
Griff W.

IMovie video project I made has no audio working after power failure

I have spent about a week stitching together family movies by ripping them to Apple tv format, then use a software program called MPEG streamclip to create a DV version which take about 24 gb a piece, I put 12 hours worth into iMovie which has taken a ton of space etc. So I created a project and am now about 1h 35 min in and this is getting small 3-5 clips of my son who is 7 months and my wife and myself b/c were going to England on Friday so I was created a nice movie for my new in laws and family I am meeting for the first time. So I had a saved file and iMovie was open and I had a power failure. I opened iMovie freaking out and then saw all the footage and the project still there so I was extremely thankful b/c of the 7 dvds I created due to space limitation once I imported I deleted the original (i have the original dvd but it takes about 6 hours to take from DVD to Apple TV format, then about 2 hours to export to DV and then another 1 hour to import into iMovie so each dvd took a full day for me due to work etc)
Anyway whats now happened is there is no audio on either the project or the original footage that has been imported, again about 12 hours of footage and a project thats 1 hr 35 mins. Whats strange is all other projects and imported video the sound and video works perfect. THis is the only one and of course its the most important one. ANY SUGGESTIONS WILL BE APPRECIATED.
If needed I will start over and do as much as I can but of course I am praying there is a simple solution.
Thanks.
newest iMovie, newest OSX etc if that helps

Thought you could use this info about getting FireWire to work!
First, you should always Repair Permissions in Disk Utility before and after any update; I would do that now. If you installed your update with FireWire plugged in, your Mac may not recognize it anymore.
Try resetting your FireWire ports by disconnecting all FW devices, shut down your Mac and unplug it from AC power (wall socket) for 30 minutes. plug it back in and try FW.
If that did'nt work, first run the Disk Repair as shown in Apple doc.#106214 before the next step. Then, download the combo update from this site (yours may be corrupt), not Software Update, disconnect all firewire + USB devices except keyboard + mouse, Repair Permissions, re-install update, Repair Permissions again + try. Yours is the 10.4.10 Combo update ( PPC, not for Intel systems). Others reading, download the Combo that applies to your system.
If that still did'nt get it Zap the PRAM. While restarting Mac hold down the following key combo Command-Option-P-R. Keep holding those keys down till you hear the second start-up chime, then release.
For those of you with Macs that are not PowerBooks or iBooks, a bad internal battery can cause FireWire to not be recognized, so make sure it's good! Also, here is Apple doc.#88338 on getting FireWire to work.
Cheers!
DALE

HP PSC2500 All-In-One noise after Power Failure

Product: HP PSC2510 All In One
OS: Windows XP Home
No Error Messages
No Changes made to OS or Printer
The issue:
After a Power Failure, upon starting the printer up, the scanner bar attempts to locate the Home Position but once it gets to the area it is supposed to set at, it continues to move to the right and makes a repeating (gear) noise.
The only fixes I have come across are:
1) Opening the scanner bed (glass top) and cleaning the glass where the white strip runs along the glass.
This stops the noise and allows the scanner to reset corretly for 1 to 3 months.
2) Holding the Cancel button or OK + Cancel.
This allowed the printer to reset correctly 1 time.
Now, the Hard Reset and Semi Reset will not work.
Again, this issue ONLY happens after a power failure or if the plug is pulled...
The issue does not happen if the power is shut off correctly.
I am sure that Opening the top and cleaning the glass will work but this is a serious headache for a printer that cost over $225.
I am a Computer Repair Technician but Printer issues of this nature are not in my area of expertise
Is there anyone who can tell me the possible cause and/or Permanent fix for this issue?
I cannot find any other information about this issue online, and I cannot find a Service Manual.
Please help because this is my work printer.
Please email me at:
{Personal Information Removed}

UPDATE: As it stands, I opened the scanner bed and cleaned the glass Home Position strip (for the 6th time now) and low-and-behold, the printer functions properly again.
I know this issue will happen again in a few weeks to a month or so...
My question still stands...
Can ANYONE come up with a permanent solution to repair this issue?
Thanks again in advance.

Cannot see the array after power failure

Hi,
today, after a power failure overnight, my XServe G4 cannot see the XServe RAID plugged in.
I've reset each controller (but I use just the first), done everything, but I cant still get mount the RAID on desktop. With RAID Admin the RAID seems to be functional, exceps for the "array", that I can't see. If i click on the drives, the RAID Admin say to me that's SPARE DISK (sic!). In the Utility windows I've tried to rebuild the array, verify the array, try to recognize the array, but everytime the button is greyed out, and I can't start the rebuild. Utility Disk don't see the RAID at all.
TIA to all Apple SysAdm that would help

I think your best option here is to contact AppleCare, to see if they have suggestions that can help.
Are you running the 1.5 firmware on the Xserve RAID itself?

Reset TC with Original Settings after Power Failure

Similar Messages

Maybe you are looking for