Resetting air-ap1131ag-e-k9 to default configuration.

I am having a small problem resetting the AP to default config.
Off course I have tried the cisco way but the AP still retains some parts of old config.
Can someone tell me how to full (clean) reset the AP?
Thanks,
Piotr,
p.s. can option 43 for dhcp help?

Hi,
I am having the same issue : when resetting the AP1131AG to defaults, it does not restart and does not take into account the defaults settings...
Same thing when I want to change the configuration using HTTP interface - loading a new config.txt file - in the "System Configuration" part of the IOS 12.3(8) software. Nothing happens !
But what is strange is that for some APs I do not have the problem and for some others yes...
thanks for your answers !
Alexis

Similar Messages

Reset to default configuration on WLSM

I was configuring AAA on my WLSM and managed to negate console access , how do i reset the WLSM module ot its default cocnfiguration, or at the very least, get the password recovery script needed to get access to my WLSM back!

Hi
It seems like i have the same problem getting Tacacs login to work, i i try to type in
"aaa authentication login default group tacacs+ enable none"
Then i will loos access to the WLSM, however i have not saved my config so i can just restart the module.
have you any new information about AAA for console access ??

AIR-AP1131AG-E-K9 have been converted to LW how do I convert it back to Auto?

Hi,
One of my clients has a new WiFi solution and he has given me his old AIR AP1131AG-E-K9 to my LAB. The problem is that access-points have been converted to LW and the customer has thrown out the controller.
I do not know the enable password, how can these APs be reset to their default setting?

Resetting to Default Settings Using the CLI
Caution You should never delete any of the system files prior to resetting defaults or reloading software.
If you want to reset the access point to its default settings and a static IP address, use the write erase or erase /all nvram command. If you want to erase everything including the static IP address, in addition to the above commands, use the erase and erase boot static-ipaddr static-ipmask command.
From the privileged EXEC mode, you can reset the access point/bridge configuration to factory default values using the CLI by following these steps:
Step 1 Enter erase nvram: to erase all NVRAM files including the startup configuration.
Note The erase nvram command does not erase a static IP address.
Step 2 Follow the step below to erase a static IP address and subnet mask. Otherwise, go to step 3.
a. Enter write default-config.
Step 3 Enter Y when the following CLI message displays: Erasing the nvram filesystem will remove all configuration files! Continue? [confirm].
Step 4 Enter reload when the following CLI message displays: Erase of nvram: complete. This command reloads the operating system.
Step 5 Enter Y when the following CLI message displays: Proceed with reload? [confirm].
Caution Do not interrupt the boot process to avoid damaging the configuration file. Wait until the access point/bridge Install Mode LED begins to blink green before continuing with CLI configuration changes. You can also see the following CLI message when the load process has finished: Line protocal on Interface Dot11Radio0, changed state to up.
Step 6 After the access point/bridge reboots, you can reconfigure the access point by using the Web-browser interface if you previously assigned a static IP address, or the CLI if you did not.
The access point is configured with the factory default values including the IP address (set to receive an IP address using DHCP). To obtain the access point/bridge's new IP address, you can use the show interface bvi1 CLI command.
The 1300 series access point/bridge assumes a radio network role of a root access point. To configure it as a bridge, you must manually place it in install mode in order to align the antennas and establish a link. To establish the link you must have two access point/bridges configured in the install mode. In the install mode, one access point/bridge must be configured as a root bridge and the other a non-root bridge. To facilitate the configuration, an automatic option is available when the access point/bridge is in the install mode. After the wireless link is established and the bridge antennas are aligned, you take both access point/bridges out of install mode and place them on your LAN as root and non-root bridges.
Note "Resetting the Device to Default Settings" sectionIf xon/xoff flow control does not work, use no flow control.
Step 7 When connected, press enter or type en to access the command prompt. Pressing enter takes you to the user exec mode. entering en prompts you for a password, then takes you to the privileged exec mode. The default password is Cisco and is case-sensitive.
Note If xon/xoff flow control does not work, use no flow control.
Step 8 When connected, press enter or type en to access the command prompt. Pressing enter takes you to the user exec mode. Entering en prompts you for a password, then takes you to the privileged exec mode. The default password is Cisco and is case-sensitive.
Note When your configuration changes are completed, you must remove the serial cable from the access point.

Bridging AIR-AP1131AG with TP-Link

Hi Guys,
Today I want to build a wireless bridge using AIR-AP1131AG (running WLC) and TP-LINK wireless router.
The result is failed. May I know AIR-AP1131AG is support bridging the wireless connection with other vendor's access point or not?
In the TP-Link I already match its SSID, Channel and put the mac-address of the AIR-AP1131AG.
In the WLC I already see too TP-LINK mac-address is already become a client.
So what's the problem guys?
Thanks Guys

Well bridging isn't supported when using a wlc, only workgroup bridge. So what your trying to accomplish will not work. You would have to convert the 1131 to autonomous, but you would need another Cisco device configured as a bridge on the other end. Or else you can leave the 1131 on the wlc and get a device that functions as a workgroup bridge or Ethernet converter. I have used the Buffalo Ethernet converters and the work just fine. You can use most of the the Cisco APs starting with the 1131 as WGBs also.
Sent from Cisco Technical Support iPhone App

How to reset a ISE device to factory default?

Hello guys,
I just started learn Cisco ISE (TrustSec 2.0), i have my company device which that set on pre-configured configuration from my company meant configured database password.
So i want to ask that how can i reset ise device to factory default configuration.
Plz give me answer as well as possible, thanks in advance.

Sure...
application reset-config Resets the Cisco ISE configuration to factory defaults.
Sent from Cisco Technical Support iPhone App

AIR-AP1131AG-I-K9 support AES 256 bit ?

hi,
I have several AP devices:
Product/Model Number: AIR-AP1131AG-I-K9
System Software Filename: c1130-k9w7-tar.124-3g.JA
System Software Version: 12.4(3g)JA
Bootloader Version: 12.3(8)JEA
i need to know if AES 256 bit is supported by this devices and if the current software need to upgrade for that.
Regards,

HI Ben,
As per my knowledge this Software dont support 256 bit key size.
Here is the link:http://www.cisco.com/c/en/us/td/docs/wireless/access_point/12-4_3g_JA/configuration/guide/ios1243gjaconfigguide/s43wep.html
another version: 12.3(8)JA supports 256 bit key size to protect data traffic,
http://www.cisco.com/c/en/us/td/docs/wireless/access_point/12-3_8_JA/configuration/guide/1238jasc/s38wep.html
Regards
Don't forget to rate helpful posts

Is there an ARD command or Unix command that I can send to reset the desktop background image to default?

I was forced to create a local user with an automatic login on all of the machines in the building. I listed off many various issues that could come arise by doing this but was tuned out. Now people are changing all of the desktop backgrounds to some pretty inappropriate images. I forewarned the person ordering this that this may be one of the many issues that would arise when doing away with our server based logins, and now I am charged with fixing every desktop every time someone changes it to something inappropriate.
Is that an Apple Remote Desktop command or a Unix command that I can send through ARD v3.5.3 to the machines to reset the desktop background image to the default Aqua Blue jpeg image located in the /MacintoshHD/Library/Desktop\ Pictures/Aqua\ Blue.jpg.
The machines that I am dealing with have OS X 10.4.11, OS X 10.5.8, OS X 10.6.8, and OS X 10.7.4 installed on them, but the OS X 10.4.11 machines are the ones that are creating the biggest issue so I would like to deal with those first.

Ya, I'd love to have the computers connected to the Xserver, unfortunately against my heeding, I was ordered to take them off of the Xserver, so they only have a local account that automatically logs in on startup, and even though I have Parental Controls set, I can not stop them from going to Safari, selecting an inappropriate image and setting it as the background, so now I’ve been ordered to fix all of the backgrounds that people are messing with.
My Xserver is running OS X 10.4.11 Server Edition. Yes, I would love a new server, but that’s not happening due to budget cuts.
So what I am hoping for is a command that I can put into Apple Remote Desktop v3.5.3 and push out to all of the computers via its Unix commands and reset all the desktops to their default image.

Problem converting air-ap1131ag-a-k9 to Lwapp

i have a person on my team who converted some autonomoous air-ap1131ag-a-k9 to lwapp. I don't think they did it right.
what they did is , booted the ap ( at this point it was running in autonomous mode), set the ip to 192.168.1.200 and their laptop to 192.168.1.100 connected the laptop directly to the AP. (I have found out that these AP's were old AP's that previously had configs on them, ( static ips, a whole config) they came from another building , they were the ones that other lwapps replaced.)
they then went to the web gui of the AP , went to software upgrade and loaded the lwapp recovery image on the ap (c1130-rcvk9w8-tar.124-10b.JA3.tar). the software loaded fine, and converted the AP . and thats all they did
(I had mentioned that we should use the upgrade tool, but they didn't listen)
the aps got mounted , on the ceiling in the hospital, but when they went to turn them on, they didnt show up right on the controller , they kept joining and unjoining..
i think there is a problem with the SSC, i remember, something like the time had to be the same on the ap and on the WLC.
anyways, these could be older AP's before 2005 ( unknown to me) which would mean they dont hav MIC's and have SSC. and the ap is refusing them is my thought.
the WLC is setup to accept self signed certs.
anyways...
these aps are now mounted on the ceilings , and when you do a show cdp nei, it has an ip address from when it was an autonomous ap.
Also, what is the best process you have found to convert Old autonomous 1131 AP's to lightweight mode?
thanks
the controller is running 4.2.176 WLC code. i currently don't have Access to WCS or a spare controller to use with the upgrade utility.
the controller is a 4404-100

i went to the wlc and issued the command
debug lwapp events enable
i got the following output
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 Received LWAPP JOIN REQUEST from AP 00:11:20:1a:07:a9 to 06:0a:10:10:00:00 on port '29'
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 AP AP0011.201a.07a9: txNonce 00:00:00:00:00:00 rxNonce 00:00:00:00:00:00
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 LWAPP Join Request MTU path from AP 00:11:20:1a:07:a9 is 1500, remote debug mode is 0
Sat Jun 13 12:41:51 2009: 00:11:20:1a:07:a9 Processing Radius Response: AP Authorization failure for 00:11:20:1a:07:a9
Sat Jun 13 12:41:54 2009: 00:1e:f7:ed:e8:aa Did not receive hearbeat reply from AP 00:1e:f7:ed:e8:aa
Sat Jun 13 12:41:54 2009: DTL Deleting AP 5 - 0.0.0.0
Sat Jun 13 12:41:55 2009: 00:11:21:89:fb:30 Received LWAPP ECHO_REQUEST from AP 00:11:21:89:fb:30
Sat Jun 13 12:41:55 2009: 00:11:21:89:fb:30 Successful transmission of LWAPP Echo-Response to AP 00:11:21:89:fb:30
Sat Jun 13 12:41:55 2009: 00:21:55:c2:06:20 Received LWAPP DISCOVERY REQUEST from AP 00:21:55:c2:06:20 to ff:ff:ff:ff:ff:ff on port '29'
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP RRM_DATA_REQ from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Airewave-Director-Data Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Received LWAPP STATISTICS_INFO from AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:56 2009: 00:11:5c:03:3c:b0 Successful transmission of LWAPP Statistics Info Response to AP 00:11:5c:03:3c:b0
Sat Jun 13 12:41:58 2009: 00:1d:70:f4:3e:50 Received LWAPP DISCOVERY REQUEST from AP 00:1d:70:f4:3e:50 to ff:ff:ff:ff:ff:ff on port '29'
can someone help me decipher what it means, i think i need to debug to get the sha key.
there are about 14 new ap's. and they all have problems.
thanks

AIR-AP1131AG-A-K9 Reload Reason: FAILED CRYPTO INIT.

Hi All,
I have a standalone AP of model AIR-AP1131AG-A-K9 and have changed the mode to LAP by using mannual archive command. However after changing the mode to LAP it gives below log and keep on booting.
Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
> I did found from below link that the reason is as mentioned in point number 9, however solution didnt worked.
http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a00808f8599.shtml
> I did downloaded CiscoAironet-AP-to-LWAPP-Upgrade-Tool-v34.exe to upgrade but after executing this file nothing happens.
Kindly help me in understanding whats going wrong with my AP?
Here is the logs.
*Mar 1 00:00:06.644: %LINK-3-UPDOWN: Interface FastEthernet0, changed state to up
*Mar 1 00:00:07.644: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
ap>
*Mar 1 00:00:18.603: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:24.691: %LWAPP-5-CHANGED: LWAPP changed state to DISCOVERY
*Mar 1 00:00:24.711: LWAPP_CLIENT_ERROR_DEBUG: lwapp_crypto_init_ssc_keys_and_certs no certs in the SSC Private File
*Mar 1 00:00:24.711: LWAPP_CLIENT_ERROR_DEBUG:
*Mar 1 00:00:24.711: lwapp_crypto_init: PKI_StartSession failed
*Mar 1 00:00:24.729: %SYS-5-RELOAD: Reload requested by LWAPP CLIENT. Reload Reason: FAILED CRYPTO INIT.
*Mar 1 00:00:24.729: %LWAPP-5-CHANGED: LWAPP changed state to DOWNXmodem file system is available.

One of the errors is saying that it can't find any SSC in the private file.
This yells me the AP doesn't have a certificate. Why you'll want ti do is reload an IOS image on the AP and then use the conversion tool to load the capwap image. By using the conversion tool, it wil execute some commands that create a SSC, a self signed certificate. Then you load the SSC on the WLC and the AP should be able to boot up and join.
http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
Sent from Cisco Technical Support iPhone App

Setting Default Configuration in 1.4.2

Previous versions of Java Web Start had a default configuration file javaws.cfg which contained the default preferences. When JWS was installed on PCs in our intranet, we could switch the cfg file to one which, amongst other things, set the proxy correctly and disabled shortcut creation. Then when any other user logged on to the PC, they would get a copy of this cfg file.
But in JWS 1.4.2 there no longer seems to be a default cfg file. When a user logs on they get defaults which are incorrect for our environment. This is a problem when several different users share the same PC. Whenever a new user logs on to the PC and uses Java Web Start, we must set up the preferences manually.
Our users are in a call center and are not capable of setting preferences themselves. In fact in the past we have removed the JWS icon from the desktop because we don't want them to even know it exists. All they know how to do is click a link (to a jnlp document) on a web page.
Is there some way to set the default preferences at install time that I've missed?
Thanks,
Simon.

Educated guesswork mostly; read over the JavaOne "whats new with web start" to get a feel for the changes yourself (http://servlet.java.sun.com/javaone/sf2003/conf/sessions/display-1486.en.jsp). Several things here will lead to internal changes. While it's location isn't likely to change (they're in the right place now - in the user profile dir) the contents, structure and config files certainly will.
Biggest single change is the unification of Java Plugin and Web Start, according to the slides this includes the merging of the applet & web start caches and configuration dialogs (it's not a big leap to assume this means merging their config files also). The new 1.5 Jar Hyper Compression format will also doubtless come into play changing the very format of the Jars getting cached. The other big change is to the security system - both opening up the sandbox model and a new central administration system will mean that the preferences on a users machine may be overridden at any time by the administrator. The cache structure itself undergos a big change with the new 'System Cache' - given that users cannot read from another users profile, this system cache will need to be stored in some shared directory elsewhere. A move that will split normal operation into a pair of active caches further obfuscates assumptions about the internal structure somewhat. This only scratches the surface here - needless to say, big changes ahead.
For the 'system cache' It'll be interesting to see how the web start team get around the default privileges assigned to a domain user under XP typically doesn't allow writing to a directory outside of their user profile folder (default privs are restricted). Similarly I'd like to see how well the new JNLP file associations work out in a similar scenario. Adding a file association requires writing to the registry; this again is typically a prohibited operation requiring local administrator rights to the machine. I hope the web start team have come up with answers to these problems and not just take the Java update line of only working while the user is logged on as a local administrator (http://www.javadesktop.org/forums/thread.jspa?threadID=184&tstart=0). This severely limits your user base to non-networked single user machines (home users), the network admins machine and windows 98 & me boxes which don't share the security model.
Finally it's not a good idea to make any assumptions about the internal layout and contents of any of Sun's undocumented services, it's always going to be prone to change without warning. Developers make changes to these at their own peril and only have themselves to blame when their code suddenly stops working.
- Richard

Load default configuration in BIOS to fix sound, caused another problem

Hey !
I have had problem to get sound in my T61, and used Lenovo support, Troubleshooting, to fix it.
I did as it told in Lenovo Support.
In BIOS Setup utility menu setup I pressed F9.
Then I selected YES to load the default configuration.
After that I pressed F10 key and YES to save the configuration.
But after that when I start the computer it says that a failur has occured, and windows has shot down to avoid problems with the computer.
Is there any way of going back in the BIOS setup, so I should get it work again ?
Thanks in advance/ Kurt
Moderator edit: Subject edited for clarity.

Hi !
I solved it with money !
I went to a company, and they fixed it, Don't ask me how ! I did not understand when they described it.
Anyway I have another problem with the sound, as you can see in the other message !
They tried to fix that to, but could not solve the problem.
George

How can I reset the age entered during the first configuration set up?

how can i reset the age entered during the first configuration of a brand new i pod touch. The age is incorrect and does not allow me to open a new i-tunes at a later configuration step. Error meesage: you are not old enough to open a new i-tunes account.
Thanks for support to solve the problem.

- Terminate the setup for obtain the account and then try again with same email address.
- Next would be to contact iTunes.
Contact iTunes

MS ssis service: registry setting specifying configuration file does not exist. attempting to load default configuration file. SQLIService100 - event id 274

window 2008 R2 server ---- after installing SQL 2008 R2 then applying sp2 / sp3 I noted a warning -
Note this server had SQL 2008 R2 uninstalled previously.
MS ssis service: registry setting specifying configuration file does not exist. attempting to load default configuration file.
SQLIService100 - source
event id- 274
user - N/A
Task category - service control.
Do we need to fix something and how do we fix this warning event?
dsk

You could search online for this warning. I was able to find http://superuser.com/questions/346264/event-log-warning-registry-setting-specifying-configuration-file-does-not-exist
where the fix is "in your registry, go to:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\MSDTS\ServiceConfigFile
or
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SQL Server\100\ServiceConfigFile
if value is empty then add in:
C:\Program Files\Microsoft SQL Server\100\DTS\Binn\MsDtsSrvr.ini.xml"
Arthur
MyBlog
Twitter

How to retrive the overwritten SAP Default Configuration

Hi There,
I was trying to enhance the component BT115IT_SLSO to add some new fields into the table view Items.
I copied the view configuration to my Z config key but by mistake & added the fields into the default view and saved the changes. Now the default configuration is screwed up.
Can some one point out how to retrive the SAP standard configuration( where it is stored ). In the configuration tab of the view the configuration looks ok but in Web UI I see all the columns available in the context node, and makes the view useless, when I go to the personlization of the view all fields shows the message < Error in Meta data > and I can not see the details of the fields.
I have already backed off my enhancement. Now I want to retrive the view configuration.
Your help will be highly appreciated.
Thanks,
Vikash.

Issue resolved.
Solution was In BSP workbench when I went to choose configuration I saw that just next to std conf there was column for cust conf. and both were marked X so I deleted the conf and that gave me the standard conf back.
Thanks,
Vikash.

All my programs are opening in adobe even the system restore and the regisrty - how do I reset all programs to their originall default programs. Please help

all my programs are opening in adobe even the system restore and the regisrty -
how do I reset all programs to their originall default programs.
Please help.
PS I have also tried starting in save mode and still have the same problem.

Hi,
As
BurrWalnut mentioned, first please run a virus scan to eliminate virus infection (if AV program is not opened in adobe)
The files association could be corrupted in your situation, apart from the solution posted in the first reply, I also suggest you check Control Panel\All Control Panel Items\Default Programs\Set your Default Programs or Associate a file type or protocol
with a progra,, manually check the association and check if it can do some help.
Add: another way to open restore point is launching it in recovery console, please refer to this guide
http://windows.microsoft.com/en-hk/windows/what-are-system-recovery-options#what-are-system-recovery-options=windows-7
Yolanda Zhu
TechNet Community Support

Resetting air-ap1131ag-e-k9 to default configuration.

Similar Messages

Maybe you are looking for