Resolution when copying a graphic from Preview
When I select a graphic in Preview and copy it, the resolution always appears to be "screen" resolution (i.e., when I paste into Photoshop). Any way to copy at a higher resolution? The copies resolution does not appear to depend on the pdf magnification. (I used to do this in Acrobat; it used to be that I could 1) select the area I want to copy; 2) zoom in as much as I want; 3) copy; then the image would be copied at the zoom magnification. Now there's just a snapshot tool that takes a picture at the current zoom level, so there's no easy way to do this when zoomed in so much that a lot of the image is outside the viewable window.)
The select tool should be selecting the original resolution, no matter what the zoom. That may only be screen resolution.
You are not using the System's screenshot mode for selecting the graphic, are you? You should using Preview's Select tool, from the Tool menu.
Similar Messages
-
HP LaserJet MFP M476dw paper size mismatch when copying or scanning from ADF
We have HP Color LaserJet MFP M476dw that has an issue when copying or scanning from the ADF.
Put a single A4 sheet in the ADF and choose copy, with all settings correct & no resizing, and the output copy is moved down the page (increased top marging by a couple of inches).
My initial thoughts were a paper size issue (e.g. treating A4 as Letter or vice versa) but all settings look correct. I have even done a reset and started over and the problem remains.
If I take the original and place it on the flatbed and copy from there with all the same settings then it works fine.
There is a similar issue when scanning from the ADF. Again, scanning from the flatbed works fine.
I've tried all I can think of. Does anyone have any further suggestions? Could it be a fault in the ADF?
Here's the full device settings info:
Device Configuration
[Shop for Supplies][Support]
Product Information
Product Name:
HP Color LaserJet MFP M476dw
Formatter Number:
YF10C9X
Serial Number:
CNB7G2H6T9
Service ID:
24113
Firmware Datecode:
20131122
Disable Fax:
No
Telecom Version:
05-031-001
Location:
UK
ADF Installed:
Yes
Max Monochrome Print Quality:
600x8
Max Color Print Quality:
ImageREt 3600
Controller Number:
72
Duplexer Version:
0
Device Description:
HP Color LaserJet MFP M476dw
Language:
English
Default Settings:
Self-managed
Asset Number:
Your Company Name:
Contact Person:
Device Location:
Geo Location:
Product Security:
Off
Wired HW Address:
fc:15:b4:78:28:46
Wireless HW Address:
54:35:30:2f:d7:fc
Network In Use:
Wired
Host Name:
NPI782846
IPv4 Address:
192.168.9.18
IPv6 Address:
FE80::FE15:B4FF:FE78:2846
Total Memory:
256 MBytes
Available Memory:
117.7 MBytes
Installed Personalities and Options
PCL6
(20040201)
AirPrint
PCL
(20040201)
PDF
(20040201)
PS
(20040201)
USB Flash Drive:
Empty
Impressions
Total Impressions:
10684
Monochrome Impressions:
4799
Color Impressions:
5885
Total Equivalent Impressions (A4/Letter):
10684.0
Monochrome Equivalent Impressions (A4/Letter):
4799.0
Color Equivalent Impressions (A4/Letter):
5885.0
Duplex Sheets:
1223
Jam Events:
0
Mispick Events:
4
Photo Color Impressions:
0
Photo Monochrome Impressions:
0
USB Flash Drive Insertions:
0
Images Scanned to USB Flash Drive:
0
Copy Flatbed Images Scanned:
373
Copy ADF Images Scanned:
409
Copy Monochrome Impressions:
1122
Copy Color Impressions:
102
ADF Images Scanned to Host:
0
Flatbed Images Scanned to Host:
0
Images Scanned to E-mail:
0
Images Scanned to Network Folder:
0
Fax ADF Images Scanned:
23
Fax Flatbed Images Scanned:
1
Fax Impressions:
18
Images Sent from PC:
0
ADF Images Scanned:
1149
Flatbed Images Scanned:
779
Scanner Jam Events:
8
Paper Settings
Default Paper Size:
A4
Default Paper Type:
Plain
Tray 1 Size:
A4
Tray 1 Type:
Letterhead
Tray 2 Size:
A4
Tray 2 Type:
Plain
Paper Out Action:
Wait Forever
Manual Feed:
Off
Duplex:
Off
Bind:
Long Edge
Print
Auto Continue:
Off
Number of Copies:
1
Courier Font:
Regular
Orientation:
Portrait
Monochrome RET:
On
Wide A4:
No
Monochrome Resolution:
600
Monochrome Bits per Pixel:
8
Color Resolution:
600
Color Bits per Pixel:
32
IO Timeout:
120 Seconds
Jam Recovery:
Auto
Personality:
Auto
Print PS Errors:
Off
USB Flash Drive
Print Documents:
Number of Copies:
1
Paper Size:
A4
Paper Type:
Plain
Fit to Page:
On
Collation:
Off
Output Color:
Color
Print Photos:
Image Size:
10 x 15 cm
Paper Size:
A4
Paper Type:
Plain
Lighter/Darker:
<-----*----->
Number of Copies:
1
Output Color:
Color
Scan Settings:
Scan Resolution:
150
Scan File Type:
PDF
Scan Paper Size:
A4
Flatbed Scanner:
Single Page
Document Feeder:
1-Sided
File Name Prefix:
scan
Output Color:
Color
Copy
Optimize:
Auto Select
Lighter/Darker:
<-----*----->
Paper Size:
A4
Paper Type:
Plain
Collation:
On
Number of Copies:
1
Reduce/Enlarge:
Original=100%
Draft Mode:
Off
Tray Select:
Auto Select
Two-Sided:
1-Sided to 1-Sided
Multi-Page Copy:
Off
Fax
Your Company Name:
HP Fax
Answer Mode:
Automatic
Rings to Answer:
2
Distinctive Ring:
All Rings
Dial Prefix:
Off
Fax Resolution:
Fine
Lighter/Darker:
<-----*----->
Fit to Page:
On
Glass Size:
A4
Dialing Mode:
Tone
Redial if Busy:
On
Redial if No Answer:
Off
Redial if Comm. Error:
On
Detect Dial Tone:
Off
Billing Codes:
Off
Extension Phone:
On
Stamp Faxes:
Off
Private Receive:
Off
Confirm Fax Number:
Off
Allow Fax Reprint:
Yes
Print Duplex:
Off
Fax/Tel Ring Time:
20
Fax Speed:
Fast (V.34)
Error Correction:
On
Forward Fax:
Off
Block Junk Faxes:
Off
Phone Line Volume:
Medium
Alarm Volume:
Medium
Ring Volume:
Medium
Key-Press Volume:
Medium
Fax Confirmation:
Never
Fax Error Report:
Never
Include First Page:
On
Auto Log Print:
On
Print T.30 Trace:
Never
Paper Types
Plain:
Normal
HP Matte 90g:
Normal2
HP Matte 105g:
Heavy
HP Matte 120g:
Card stock
HP Matte 150g:
Extra Heavy
HP Matte 200g:
Extra Heavy
HP Glossy 120g:
Glossy
HP Glossy 150g:
Glossy
HP Tri Glossy 150g:
Glossy
HP Glossy 200g:
Heavy Glossy
Light 60-74g:
Light
HP EcoSMART Lite:
Extra Light
Intermediate:
Normal2
Mid-Weight 96-110g:
Heavy
Heavy 111-130g:
Card stock
Extra Heavy 131-175g:
Extra Heavy
Hvy Glossy 111-130g:
Light Glossy
X-Hvy Glossy 131-175g:
Glossy
Card Glossy 176-220g:
Heavy Glossy
Color Transparency:
Transparency
Labels:
Label
Letterhead:
Normal
Envelope:
Envelope
Heavy Envelope:
Heavy Envelope
Preprinted:
Normal
Prepunched:
Normal
Colored:
Normal
Bond:
Heavy
Recycled:
Normal
Rough:
Heavy
Heavy Rough:
Heavy
HP Tough Paper:
Tough Paper
Opaque Film:
Tough Paper
Energy Settings
Sleep/Auto Off After:
30 Minutes
Wake on These Events
USB Job
Yes
LAN Job
Yes
Wireless Job
Yes
Control Panel
Yes
Fax Ring
Yes
Shut Down After:
Never
LaserJet Updates Settings
Check Automatically
Yes
Prompt Before Install
Yes
Allow Downgrade
Yes
Allow Updates
Yes
Miscellaneous
Extended print modes modified:
No
Very Low Setting (Black Cartridge):
Prompt
Very Low Setting (Color Cartridges):
Prompt
Low Threshold (Black Cartridge):
5%
Low Threshold (Cyan Cartridge):
3%
Low Threshold (Magenta Cartridge):
3%
Low Threshold (Yellow Cartridge):
3%
Store Usage Data:
On Supplies
USB Connection:
No
Font Source:
I (Internal)
Font Number:
23
Font Pitch:
10.00
Font Point Size:
12.00
Symbol Set:
PC-8
Form Length:
64 Lines
Append CR to LF:
NoTo get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial Forums.
I hope this helps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution! -
How do you copy a page from preview to duplicate it?
Hello,
I want to copy a page from preview so that I have 2 pages that are the same. Before I upgraded to Maverik, I used to be able to right click on the page (in the sidebar) I wanted, click "copy" then right click in the sidebar and click "paste".
Now when I right click on the page in the sidebar I don't get the option to copy and paste.
I found that if I opened a new copy of the same document, I could import it into my working draft then delete all of the pages I didn't want, but that is way too much work. If someone could help I would be very grateful.
Thank you so much!Not exactly what you want, but Preview/Edit/Insert/then select the file. Preview/Edit/Delete pages you don't want. That is the only way I could figure out how to do it from within Preview.
-
Copy a graphic from java and paste it to WORD
Hi all,
Is it possible to copy a graphic from a java applet and paste it in a word document ?
Any example should be appreciated.
Thanks ? ;-)
OlivierThis is not possible on a generic applet because the browser security does not allow access to the system clip board. This can be done in a Java application or a signed applet.
-
When copying raw files from Extreme IV card to hardrive, finder copies a few files then exits task and wipes the card clean of all images. Have tried new card and card-reader to no avail. Have done this many times on other macs with no problems.
Can edit files off the card, in CameraRaw, prior to 'copying' them, ie can 'save as' to the hard drive, so files seem okay on card, before I try to copy them using copy and paste.
Running OS 10.8.3 on a new macbook pro.Rita,
The process for determining what is causing the files to be corrupt can be a tedious one depending on the following:
1. Can you review the images on your camera's LCD screen without problems? If not then the problem is most probably either a corrupted/faulty memory card or a faulty camera. If this is the case then your best bet at recovery (of sorts) is to use a program such as BrezzeBrowser from BreezeSys to extract the embedded jpeg versions of the corrupted RAW files from within each RAW file. Chances are, you won't manage to actually repair the corrupted RAW file but the jpegs are better than nothing.
2. If the images review ok on your camera but are corrupted when viewing on your computer and there seems to be no other problem with other files on your computer then it may be either a faulty card reader or usb/firewire cable between the card reader and the computer that is the culprit. Try the card reader with a different cable and also try a different card reader to determine the cause of the corruption.
3. If your symptoms are that you get different files corrupting over time when viewing them on your computer then the problem may be any one of either failing RAM memory, hard disk, hard disk controller or IDE/SATA hard disk cables. This is where the troubleshooting can be pretty tedious testing then eliminating each item from the list of suspicious pieces of hardware. Try the card and card reader on an altogether different computer to see if the files transfer correctly to that computer. If so then the problem lies with your computer hardware. If you haven't already done so at this stage, backup all your important data immediately (hopefully you keep backs anyway).
Hope this helps. -
Can't shown chinese text when copy & paste data from server to Outlook, Word & notepad, etc.( Office 2013)
Hi
As per the information and details provided by you, when you copy & paste a data from server to Outlook, word, notepad, then you do not receive the Chinese text.
For Outlook, please follow these steps: -
Close and reopen Outlook in your western locale (or switch the windows system to your Western locale if you changed that),
Manually change the message from Western to Chinese encoding, which you can do in all versions up to Outlook 2007.
If you want to stay in your Chinese locale in Outlook 2007, then:
After you hit reply, go to the Option tab > More Options.
In the Encoding drop-down menu, select the Chinese encoding you are working in (Not the encoding used by the person who will receive the message)
Note:
To set the Chinese locale in all versions up to 2007 the controls are under.
Tools > Options. In Outlook 2010 File tab > Options > Advanced > International options.
Unicode (UTF-8)
is a good setting for multilingual users.
Check the
Auto select 2007)/ Automatically select (2010) encoding box.
I hope this information will be helpful for you.
Thanks and regards
Shweta@G -
Copying hangs when copying large files from DVD
I'm having trouble copying large files (>2GB) from DVDs to my built-in hard drive. When I drag the file icon from the DVD window to the desktop, the progress bar pops up almost immediately, and says "0 KB of 2.3 GB copied" and "Estimated time left: 1 minute" -- and then it just sits there, doing nothing. In some cases, after five minutes or so of inactivity, the copy finally begins... but most of the time it never does. Force-Quit doesn't help; the only way out is to do an emergency restart and try again.
This problem began when I upgraded to Tiger, and several members of my office group have been experiencing the same problem on their own computers as well.
I've poked around the forum looking for answers but the only thing I could find that looked related was a conflict between iSight and some third-party external hard drives... but none of us have iSight, and none of us are using third-party external drives, so clearly that's not the issue we'rehaving.
Any help out there?
iBook G4 Mac OS X (10.4.6)Michael, I occasionally notice anomolous behaviour when files get dragged between volumes. Mostly the copying window shows an accurate and immediate indication of what's going on, but other times it just looks like nothing's happening, the display never changes, yet, it is in fact copying the files over. Now, if you're copying 2gb files from DVD to HD, it's gonna take some time, more than 5 minutes, so I'm wondering how long you've left it before forcing it to quit?
-
How to keep 300dpi resolution when saving a jpeg from illustrator
I have an illustrator cs4 file set up in 300 dpi. when I save it into a jpeg, it automatically downsizes it to 72 dpi and the quality of the image is really bad. how do i keep a 300 dpi resolution when I save my document to a jpeg file from illustrator?
Use file >> export >>jpeg>resolution >> custom 300
Sounds like you were using save for web. -
OS X 10.4.7 server: Samba leaking ram when copying large files from windows
Hi.
I'm having problems with:
Copying files from windows clients to OS X Server 10.4.7 uses up the RAM needed for the files to be copied.
If I copy a 3GB file, it uses 3GB of RAM
If I copy a 5GB file, it uses its 4GB of RAM, plus VM.
If I copy 11GB of files (that is several little files, plus some big by dropping a folder to the share), it consumes all the RAM the machine has, and because of VM paging, whatever other clients are reading from the disk (XRaid) start to have hiccups.
The RAM of the machine NEVER gets flushed after the copying has finished. So Samba is unusable as it is. I have four Xserves with 4GB of RAM, with 4 XRaids connected each one to each Xserve with its Apple Fiber Channel card and cables.
I already did the ack=0 thing, got the size of inet.tcp.sendspace and rcvspace to 8388608 and the buffer to 16777216.
The transfers rates are up to 70MB/s with 2 channel 1gb trunking, and at very sustained rates..
We are using these to edit video content (DV 25) in Sony Vegas with 2 or 3 clients for each server.
Any suggestions?
Thanks very much.
XServe G5 cluster node (4) / XRaid 7TB (4) Mac OS X (10.4.7)Michael, I occasionally notice anomolous behaviour when files get dragged between volumes. Mostly the copying window shows an accurate and immediate indication of what's going on, but other times it just looks like nothing's happening, the display never changes, yet, it is in fact copying the files over. Now, if you're copying 2gb files from DVD to HD, it's gonna take some time, more than 5 minutes, so I'm wondering how long you've left it before forcing it to quit?
-
CR duplication when Copy/Pasting text from a JTextArea
I have a typical scenario of having text in a JTextArea. When I select some of that text and try to paste it either to an external text editor or even in the same JTextArea, I am getting extra line spaces in the screen.
For example, if I have the following text:
<a id=1>
<b/>
</a>When I copy paste it, I get:
<a id=1>
<b/>
</a>When I looked to see what characters were being used for the CR, I see "\r\n". This is the standard line.seperator for Windows OS which is fine. When I save this text to a file using the Java I/O libraries, it is fine (no extra lines). But when copy/pasting it prints extra lines.
Has anyone had similar problems?Has anyone had similar problems? No. How are you doing the copy/paste? Did you write your own routines or are you using the default Actions. By default, when a Document is loaded it will convert the "\r\n" end of line string to "\n" and store the single character in the Document. When you use the getText(..) method the enod of line string will be expanded to "\r\n" on a Windows system, but this should not happen in a copy/paste operation. How do you add data to your text area?
This section from the Swing tutorial on "Text Component Features" has a working example of using copy/paste:
http://java.sun.com/docs/books/tutorial/uiswing/components/generaltext.html -
Error code 8084 when copying large files from VNX servers
Hi,
We are experiencing problems when attempting to copy large files from our central VNX servers (EMC) using the connection format of smb://<host>/. With Mavericks this will be SMB2, presumably. Anything over a few MB in size fails with the error:
The operation can’t be completed because an unexpected error occurred (error code -8084)
Looking in the Console logs we see the following:
kernel[0]: smb2_smb_read_write_fill: len got reduced, must be running low on credits
If we attempt this on OS X Mountain Lion or below we have no problems.
If, with Mavericks, we connect using the format cifs://<host>/ then file transfers work.
Has anyone come across this before? Thinking I should also post a bug...
Cheers,
Ian
IT Infrastructure, Open University, UKNot helping but others are having the same problem...
http://discussions.apple.com/thread.jspa?messageID=2564624 -
Unknown error when copying any object from Illustrator to Photoshop
When trying to copy an object from Illustrator CS5 and paste it to Photoshop CS5 on Windows 7 I get the the following error when I switch from Illustrator to Photoshop:
The operation cannot complete because of an unknown error. [pdf!]
This only happens between Illustrator and Photoshop - copying an object to InDesign works fine.
I deleted the full Adobe preferences folder on D:\Users\[username]\AppData\Roaming\Adobe but that doesn't help.
Am I the only one with this issue?
QThere's definitely something wrong.
Have you rebooted your machine recently?
I'm on a Mac, so maybe something happens on Windows that I'm not aware of.
Let's see if anyone on a Windows system has any ideas.
Anyone? -
Flipped even-numbered pages when printing double-sided from Preview
My HP 2015dn printer has the ability to print double-sided. Yet I'm finding that when printing from Preview, the even-numbered pages are flipped 180 degrees. I can see the rationale for this, but I'd like to disable it and have the orientation the same for both odd- and even-numbered pages. There is a setting in the print dialog to "automatically rotate each page," but that is not what I want.
Any ideas?That fixed it. The pdfs were rotated so that they would appear in landscape orientation on my screen (they're originally photocopies of side-by-side book pages). Well, now I understand the difference between short-edge and long-edge binding! Thanks for your help.
-
No access to settl rule when copying Sales order from Quotation
Hi all
Can you help me on my following issue :
I create quotation in which I refer to a settlement rule.
WHen creating a sales order in reference to my quotation, the settlement rule in the "item account assignment" tab is not reachable ...
This mean that all costs are posted on the quotation but not in the sales order.
But we would like to keep all costs on the sales order, as we do in all our process.
I've checked the copying rules but found nothing..
Any suggestions?
thanks in advance
martineIn the standard sales order screen (type OR for example) if you go to Go To Item Account Assignment you can press on the button"Settlement Rule "
But when copying Sales Information to Sales order with standard copying requirements, you can not presse on the button "settlement rule"
Furthermore, in this tab, a field called "PC DUMMY" is now appaered on the screen ...??!!!
Any idea of what to do ??
thanks !
martine -
Choosing the optimum graphics resolution when exporting to epub from ID5
I'm creating a ebook for the iPhone that includes a bunch of images. I'd like some help choosing the correct resolution for those images when they're exported to an epub file.
These images were imported into an ID5 document as EPS files. They are 100% vector-based BW (2 bit) line art.
The Export to ePub dialog box gives me the option of choosing Low, Medium, High and Maximum resolution for bitmpas of the images that ID5 will create during the export process.
Smaller is better from the standpoint of file size and display performance, but I want the images to look sharp.
Which of these options is probably the best for the iPhone?
Thanks! --MikeDavid Bruce Hughes wrote:
Thanks for your replies. Upon further investigation, actually Pages is producing good code and it displays properly in various ebook readers, but not under iOS. *So this is not a Pages issue at all.*
Good to hear!!
Maybe you are looking for
-
Hi Friends, When we check the balance via transaction FS10N for some account( exp: 55000,552000) the closing balance 2008 and the opening blance 2009 are not the same which is not the case when we check with TC FBL3N( for Ccode 0900 & 9170 & 9183 ON
-
I created a new help project and I want to divide the project into different doc files: Ihave my general project "tas" but Iwant to have beside my Tas.doc in this project also tasintro.doc and tasbasic.doc. When i want to create these new documents I
-
Can't install windows 8.1 with boot camp
I'm trying to install windows 8.1 with boot camp and this is the message I keep getting. I've tried several times and every time I get this. I have a 2015 MacBook Pro. I've tried installing from a usb with ISO and also from a oem windows dvd. Any hel
-
Acrobat 9 Pro re-installation problem
I have a new PC where I installed Adobe Creative Suite 5 Design Premium. I deactivated the programs on my old machine succesfully and so far InDesign and Photoshop are fine. However, when I installed Acrobat (software is on a separate CD), I get the
-
E540 HELP PLS(info) with drivers, cycle count and battery also need tips
I buy my laptop mainly to play games. E540 20C600AAUS . Do the E540 come with a preinstalled graphic card? The games i plan to play with this laptop and requirements r: hope i can edit this after, should i post link or copy n paste requirements for g