Resolution would not change on Satellite 5200-801

Hello.
I have always used 1280x1024 as a resolution on my 5200-801 laptop. For some strange reason, after the last reboot the resolution stayed at 1024x768 and the 1280x1024 is no longer listed as available (the maximum that I can see on the Control Panel display settings is 1024x768, either with 32bit colors or 16).
I tried to reinstall the NVidia driver but produced no result.
What can I do? The graphics card is a NVidia Geforce4 460 Go
Regards,
Pedro

Solved. On the Control Panel I did a "Scan for hardware changes". For some strange reason all display modes are now available.

Similar Messages

  • How to reboot Satellite 5200-801 without using Recovery disk?

    Hi,
    I haven't used my Satellite 5200-801 for a while and now it won't start. This is what I get on the black screen:
    Intel Boot Agent Version 4.1.04
    Copyright 1997-2002, Intel Corporation
    PXE-E61: Media test failure, check cable
    PXE-M0F: Exiting Intel Boot Agent.
    Insert system disk in drive.
    Press any key when tready .
    I have the product recovery disk, but that will wipe all existing data and rebuild. Is there a way to start my PC without the use of recovery disk?
    Thanks for any help.

    Hi Silas & radyRoberts,
    Tried to access BIOS, but seem to have no luck. When I try to enter it during boot up, I get a black screen with the following:
    Set default value? (Y/N) BIOS v1.20 (in right upper corner)
    It doesn't matter if I press "Y" on "N" the result is the same, which is the original screen I already described.
    I also tried the Microsoft Installation disk, but nothing happened with that either. It reads the CD, but on the screen nothing but the original message appears and even that after a reboot with the CD in. If I put it in when the PC is working and "press any key", nothing changes on the screen other than the original message re-appears after it tries to reboot, but realises it's not the system disk it asked for.
    I did have a similar problem starting it about a year ago, when I previously used it, but then after few restarts, it got going again. That time I did a system and disk check and defrag, so all was well when I turned it off.
    Wii check the HDD via HDD enclosure next as RandyRobers suggested.
    Thanks for the suggests. Will let you know how and if it worked out.

  • Bugs? playback resolution will not change?

    The playback resolution will not change no matter what I choose ? it may be contributing to the distorted playback issues im having ? also when I select a clip from the project or media browser the sequence automatically starts in arri editing mode? I switch to dslr but the playback gets worse.
    win 7
    64
    gtx780

    When you refer to playback resolution, do you mean the setting highlighted in this screenshot?
    If so, what happens when you try to change the setting? And, of course, if that's not what you were referring to, please elaborate.
    And when you say "when I select a clip from the project or media browser the sequence automatically starts in arri editing mode," are you referring to creating a sequence from the clip? If so, the editing mode generally doesn't matter much unless you plan to use "smart encoding" or to enable "Match Sequence Settings" or "Use Preview Files" when you export, neither of which is recommended in most cases. The main properties of the sequence settings that you want to make sure are right are the height, width, pixel aspect ratio, and frame rate.
    As to the distorted playback issues, a screenshot might help to start troubleshooting that.
    Finally, please specify exactly which version of Premiere you have--the three-part number like 2014.0.1, not simply CC or CS6.

  • I changed my plan and was told it would NOT change my contract date......

    I recently changed my plan over the phone with a rep because I initially was going to cancel my service.  I was told that I could change my plan and save $40 a month and by changing my plan, it would NOT change my contract end date.  I just pulled up my account and not only do I see my end date extended out to another year, but the changes I made were NOT correct.  I want this fixed !!!!! 
    ONE ****** OFF CUSTOMER!!!!

    Call them back. have them do the change again. That simple.
    Good Luck

  • Unlimited data gone after I was told my plan would not change

    I went the other day to get my wife a birthday present. She had a droid bionic and has had a lot of problems.  She always mentioned that she really wanted a iPhone seeings I have had one for over 2 years with no problems.  So I thought hey why not get her the iPhone 5.  So I did as I was purchasing it I made sure to ask that we would not lose the unlimited data.  I was assured that I would not, so I went ahead and purchased the phone.  Two days later I get a text on my phone stating that I had used 90% of the data on my line.  Then the next day I received a text stating i had used all my data for the month.  So I called Verizon and they stated that because I upgraded that my line had lost the unlimited data.  I stated what I had been assured of at the store and I was told to go back to the store and complain to them.  What good would that do when you told me I could not get my unlimited data back.  What I was told next shocked me, I was told I could get my unlimited data back if I took my wife birthday present back and got a refund then my plan would revert back.  So after that I requested to speak to the loyalty department and was told they did not have one.  I stated yes they did because I had spoke to them before about a issue with a droid device. So finally he stated they did have one but they only do out going calls.  What kind of customer service is that, when you are told to take a gift back and get a refund.  Switching to a new plan would raise my bill to over $200, were is the loyalty to customers who have been with Verizon for years.  I pay 176 dollars a month now I put up with the new activation fee for all phones.  I am seriously considering taking that phone back and switching to another carrier, because it seems like Verizon d does not really care if their customers are happy or not.

    Did you purchase the phone at full retail price or the two year contract subsidized price? Was it a corporate store or a premium retailer? Did you look at your receipt and see if they kept you on the Nationwide Plan or switched to the Share Everything Plan?
    If you are within the 14 return policy period, return the device and call customer service and request an inactive pricing restoration of your previous plan and the upgrade you had used to buy the device. Since you returned the phone, the upgrade eligibility should return, but you NEED to request that your plan be reverted back to its previous setting. If you are outside of the 14 days since purchase, you are out of luck.

  • Screen resolution does not change back after using a projector

    Hi!
    My office uses several different models of macbooks, but there is a small problem with all the Airs. When I have been using them with a projector I have to change back the screen resolution manually (go to the system settings and change resolution). On the macbook pros, however, the desktop restores themselves as soon as the projector is disconnected. It seems to me that this should be the standard behaviour of all macs, does anyone know why it is not working on the Airs?
    Best regards
    Erik

    Hi Erik,
    I had this problem on a MacBook and resolved it by recreating some plist files.
    ~/Library/Preferences/ByHost/com.apple.windowserver.xxxxxxxxxxxx.plist
    ~/Library/Preferences/ByHost/com.apple.preference.displays.xxxxxxxxx.plist
    The xxxx's are your machine's EthernetID (MAC Address). I wouldn't delete, rather just move them to your Desktop and restart the computer. See if that resolves it.

  • Change Screen Resolution or not Change Screen Resolution?

    I mean is it possible to change screen resolution with Java?
    I read some topics (not in this forum) that is impossible. I know there is a method to set at full screen a frame with the favourite resolution but does it effectively exist a method to set the screen with a favourite resolution?
    For example:
            frame.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
            frame.setUndecorated(true);
            frame.setIgnoreRepaint(true);
            device.setFullScreenWindow(frame);
            if (displayMode != null && device.isDisplayChangeSupported()) {
                try {
                    device.setDisplayMode(displayMode);
                } catch (IllegalArgumentException iae) {
                    System.err.println("EX: " + iae);
            ...the device.setDisplayMode(displayMode) always throw me an exception: Invalid Display Mode (or something like that) with all permitted display modes (640by480, 800by600, 1024by768, etc...), with all permitted refresh rates, with all permitted color depths.
    Illuminate me please!
    Thanx in advance!

    Hi,
    I think i you should check this link
    http://forum.java.sun.com/thread.jspa?threadID=624649&messageID=3554316
    with help of above link you solve your problem of screen resolution
    but problem with above code is when you apply on frame that's ok but is you add any JDialog to that frame then JDialog and move JDialog with mouse dragged and dropped
    then dialog is invisibly run .
    you check this i you find any solution please post that it's urgent

  • Resolution does not change after saving.

    A previous answer does not help me.  I save a file after changing size (inches) and resolution from default of 240ppi to 300ppi, when I reopen the file reverts to the original size.  I use a Mac 10.6.8 Photoshop CS5 extended 12.0.4 x64.

    If all you change is the document DPI resolution setting  all the changes is print resolution and print size. The document size remains un-changed you sill have the same pixels you have before the resize.  Only when you resample(interpolate) the number of pixels you have for the images does the the file size change. In fact you have a completely new image not a single old pixel exist all pixels have been interpolated to increase or decrease the number of pixels the image has.

  • DVD drive stopped writting DVD's on my Satellite 5200-801

    Quick question that I hope someone knows the answer to. My DVD drive stopped writting DVD's a while ago (several system reinstalls have proved that it is the drive and not a driver error/conflict) So I got hold of another drive. Fitting was easy however it appears that there is something funny with the ide chain configuration in this laptop. The old drive was set on cable select, however the new drive is set as slave. because of this neither the HD or the DVD drive are accessable.
    Does anyone know how to switch dvd drives to cable select to make them work (I tried putting jumpers on the HD to change it between a master and slave but with no joy.)
    Thanks in advance
    John Walker

    Hi John,
    Normally, slim design CD/DVD drives are preset by the manufacturer but it is apparently possible to change the setting if you really want to. Please check out the following post :-
    http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=5946&messageID=20727#20727
    HTH

  • After Disconnecting AirPlay Mirroring, my Ext. Display Resolution Does Not Change!

    Im on Latest MBP 15, using Apple TV3 and DELL 27' Monitor as a main display.
    When Im trying to play video via AirPlay + AppleTV as a Mirroring or Extended Display, it does change main resolution of my DELL ext. Display from 2K to 1080p... And after that I can return my native DELL resolution ONLY after Rebooting (even several times).
    DELL is connected to MBP with mini D-port to D-port cable, ClickTronic (good and expensive one).
    Is there any ideas how to fix that?
    Thanks.

    Sounds like an OSX issue... try posting to the appropriate Mac forum.

  • Need latest graphic card driver for Satellite 5200-801

    Just cant find latest drivers, 3.6.3.8 not work propertly with this graphic card.
    Plz help.

    Well with drivers (version 3.6.3.8) there are some troubles playing games, where requires higher graphic, screen begins flash or where requires higher rendering i see just triangles. Yes i know that in toshiba webpage exists higer drivers version, the problem is Where?
    So far i found 5.7.8.2 version of drivers for videocard NVIDIA GeForce4 460 go (Toshiba), but realese date 04/11/2004.
    Reggards,
    Raimundas

  • Something is wrong with the cropping.  It won't let me crop the picture.  Usually the arrow would appear so I can drag it to crop the image but now the little hand appear and does not change to the arrow.

    I cannot use my crop function in editing.  The little hand would not change to the arrow hence cannot drag to crop the image.  It just happened today.

    Lets start with details - what version of iPhoto and of the OS?
    anything else that might help figure this out?
    LN

  • How to enter BIOS mode on Satellite 5200?

    Hello!
    I own a Satellite 5200-801 and Ive recently bought a new CD/DVD - rom cause the original just died. The thing is that the drive I bought is from US market and my laptop is European. So Ive double checked all the serial numbers on it and everything was correct except the manufacture serial number that I suppose makes no difference to be different.
    My problem is that when I install it the light indicator flashes normal but when it boots it shoes IDE error boot and windows doesnt see it at all. Do u know how can I enter BIOS setting to change master/slave cause I believe that there is a difference among them at this point....the original is master and the second is csel.
    Also is there a key to enter BIOS because I cant enter at all no matter key combinations. Finally if I change the reading head of the DVD/ROM and put back the original would make the change I need?
    THANKS FOR YOUR HELP!!!

    As far as I know you cannot change anything in BIOS but check it again. To enter BIOS settings press ESC button at start up.
    Good luck!

  • Satelitte 5200-801 - keys layout

    I have Satellite 5200-801 notebook with reinstalled Windows Xp Pro. The operating system was installed not from support CD that was sold with my notebook, but separately. Now I installed all the drivers. Everything works correctly, except keyboard.
    On my notebook's keyboard the keys @ and " are not on the same places like in other keyboards. @ key is not between Shift+1 and Shift+3. But it is near enter key. So what keyboard layout should I choose in order to use these keys like it is written on a keyboard? Now I have English United States... Or maybe I need additional drivers or any application, where I can change the keys assignment?
    I'll be appreciating for your any advices and help.

    Thank you so much!!! I thought that I tried all the keyboard layouts. But Engligh UK wasn't checked... So now everything is great.
    You are great. Thank you!

  • Image will not change on the Browser...Saving on the Tomcat Problem...HELP

    Hi,
    I worte a Servlet project using JBuilder 7 and TOmcat 4. THis is basically what i am doing...
    I am getting an image from database and saving it to a folder in tomcat and then displaying it on a browser.
    This application is used by multiple users...
    I am saving the Image in Tom-cat...C:\JBuilder7\jakarta-tomcat-4.0.3\webapps\examples\Image1.jpeg
    I am also displaying the image from that folder. The problem is when i run the application,
    I am seeing the same Image on the screen..Its creating the different Image file, but the image is the same.
    If i do a refresh on the page then it displays the new saved Image...
    Also, If i save the image on my local and then display it from my local it changes the images as I
    click on a Image list...
    Following is how it works when i save it and display it from my local, but if i run my application from
    another computer i am not able to see any of the images....Because its on my local.
         fos = new FileOutputStream("C:/Image1.jpeg");
         <img src="file:///C|/Image1.jpeg" height="855" name="myimage" align="middle" style="position:absolute;">;
    And this is how i am doing when i am saving to the tomcat....I am able to display it on another computer
    but would not change the image...
    fos = new FileOutputStream("../webapps/examples/Image1.jpeg");
    <img src="../Image1.jpeg" height="855" name="myimage" align="middle" style="position:absolute;">;
    Can some one please tell me what could be the Problem....
    Any help will be greatly appreciated....Thanks...

    The browser caches images so that it doesn't have to always download the same image for different pages.
    You could:
    1: Save the new image with a different name and dynamically change the name in the html.
    2: Try setting the response headers to prevent the browser from caching the images.
    response.setHeader("Pragma", "no-cache");
    response.setHeader("Cache-Control", "no-cache");
    response.setDateHeader("Expires", 0);

Maybe you are looking for