Resolve the Ethernet Port Issue of New Intel Xserve

Hi all,
I want to get Clarify the Issues in new Intel Xserve 2.26GHz Quad-Core Xeon "Nehalem" processor. The Network Connectivity of Ethernet is Shows Wrong in System Preference. If I Connect the Ehternet in Port 1, the Port 2 also Shows Connected without Pluging the Ethernet Cable in Port 2.
Port 2 is Shows Green When No Connectivity of Port1 and Port2.
I Tried in 3 Xserves with the above Configuration, all the Server Gives the same Issue. I even Formatted and Reinstalled with all the updates but the Problem prolong.
Awaiting your replies/suggestions.
Thanks
R.ELANGOVAN

Call Apple Support for assistance; this looks to be a nasty error with multiple new Xserve boxes and given these are likely covered under their initial warranty, which implies there's something seriously weird with 10.5.6 or 10.5.7, or with the Xserve early 2009 boxes, or firmware, or with what the configuration tools allow.
It appears that [threadID=2021235|http://discussions.apple.com/thread.jspa?threadID=2021235] and [threadID=2021817|http://discussions.apple.com/thread.jspa?threadID=2021817&tst art=0] are the same case?

Similar Messages

  • [SOLVED] turn off the ethernet port Leds

    I've just found out that you can turn off the leds on the ethernet ports on my new router (linksys EA2700).
    Is it possible to do the same on archlinux from software (if yes how?), or that is a hardware specific option?
    Last edited by Slaw0 (2014-11-09 18:57:17)

    As far as I know the ability to do this does depend - to some extent - on the hardware (and/or perhaps drivers and kernel modules).  But you can check /sys/class/leds to see if it is available there.  There is no entry in leds for my NIC, but various other LEDs can be controlled there.

  • Can I share internet from a airport express via the ethernet port

    I have a older airport express that I am trying to you to share the internet with a Marantz AV receiver. I used to be able to share the internet to a PS2 a few years back.
    I was able to set up another network parallel to my normal wireless network with an older moonbase style airport extreme using WDS.
    I am unsure if this is the limitation that apple has introduced to the unit, or it is a Telstra firewall issue.
    Is it possible using a combination of Airport Etremes or expresses to share the internet to a wired unit?

    I have a new airport extreme that I use all the time. I was using the older airport express for airplay.
    The older airport extreme I just pulled down from the cupboard trying to get the AVR connected.
    Since posting I have able to use the Airport extreme to connect the AVR via the ethernet port.
    Still curious why I cannot connect using the airport express.
    Interestingly the older airport extreme pushed the new airport extreme into WDS mode. Tried to hook up the express and it did not work.

  • I have a MacBook Pro and all of a sudden  I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

    I  have a MacBook Pro and all of a sudden  I cannot get wireless internet connectivity to my router or any other router, I get connectivity through the ethernet port but not wireless. This was working well till this morning

    BXB1905 wrote:
    I tried the Apple diagnostics it did not work.
    What do you mean it did not work!  What were the results of the diagnostic tests?
    Have you contacted your ISP to determine if the problem is on their end?  
    Have you changed your router channel?  Sometimes this resolves wireless problems.
    Your profile confirms you are using Lion.  Check out the following: 
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    Configuring 802.1X in Mac OS X Lion and Later

  • Can I activate the ethernet ports (routing) of Time Capsule "joining" an existing non-Apple wireless network ?

    Hello,
    I have a DSL modem that is also a WIFI router as my main WIFI network from room A. In room B, I have a TC wirelessly joining the existing WIFI network (not creating a new one). That works fine, I have one SSID, and I can wirelessly access the TC disks and backup my Mac on my TC.
    Now, I would like to connect a wired device (with on WIFI) to the ethernet port of my TC. Unfortunately, the ethernet ports of the TC don't seem to be "activated" as they do not have internet on them.
    More precisely, I'd like to connect a GE Cordless Skype Phone Model# 31591 (http://www.gephones.com/products/skype/dect-6-0-expandable-digital-cordless-phon e-with-skypetm.html) that connects to a router via Ethernet. I'm aware that I could simply connect it to the DLS router, but that's not what I want... Is there any way to activate the ethernet ports of the TC while in "join" mode ? Or do I really have to buy a Airport Express to create my main network and then extend it ?!?

    Thanks, the reason why I asked again, is because you told me to start another thread with the specifics of the device I want to connect, so I did
    Not a big deal, and it is easy to become confused.....but to be clear about this  
    Your question.....
    is there a way I can connect my Bluray player to the TC ?
    My Answer.....
    Please start a new post for that. Tell us the make and model number of the player and whether you plan to connect using wireless or Ethernet.
    so I tried to creat the main WIFI network with a first-generation Airport Express M9470LL/A (802.11b/g, no "draft N" or "n" support) and the TC wouldn't extend it either, is it too old/not supported
    Unfortunately, the "extend" setup will only work with "n" devices.  The older Express does not have a setting to "Allow this network to be extended", so the Time Capsule cannot pick up the signal.
    I'm not sure what else to suggest other than what I already have.  I'm assuming that you do not want to buy another new Airport Express.

  • Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports?

    My usb port on my Laserjet P4015n no longer works and I am unable to connect this printer to my network router because it's in a different room. Is it possible to connect an HP LaserJet P4015n printer to a computer via the ethernet ports? Of so, how would I go about making this connection? Will I need to install ethernet drivers for this to work?
    Thanks,
    Greg

    This seems to be a commercial product. For the best chance at finding a solution I would suggest posting in the forum for HP Business Support!
    You can find the Commercial Laserjet board here:
    http://h30499.www3.hp.com/t5/Printers-LaserJet/bd-p/bsc-413
    Best of Luck!
    You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

  • Is there a fix for a dead ethernet port besides a new logic board?

    My ethernet port went dead on my IMac.  I unplugged the ethernet cable and plugged it into my laptop and it worked instantly.  I am still able to connect wirelessly.  I bought an apple USB to Ethernet converter and plugged it in.  It worked for about 3 days and then it went dead.  Once again I was able to unplug the ethernet cable, plug it into my laptop and instantly had a connection.  Is there a fix for a dead ethernet port besides a new logic board and if not how do I figure out which logic board I need?
    Thanks
    Step

    This problem baffled me. I kept getting the "ethernet cable unplugged" error after testing my cables good. Was abut to write it off as port gone bad when I found this thread.
    The YouTube video reference above fixed my problem. (http://www.youtube.com/watch?v=u1P6X87qArs)
    Basically go to SETTINGS/NETWORK. Then highlight your ETHERNET port and click the ADVANCED button. From there click the HARDWARE tab.
    Set
    CONFIGURE to MANUALLY
    SPEED to whatever your ethernet speed is, in my case 1000baseT
    DUPLEX - FULL DUPLEX, FLOW CONTROL
    Leave MTU at Standard
    Hit OK.
    Then don't forget to hit APPLY. I didn't do this the first couple of times assuming hitting OK applied these settings. You gotta hit APPLY.
    In about two seconds, my Ethernet connected again.
    I went back and reset it to AUTOMATIC just to test and after doing so got the cable unplugged error again. So I am leaving it on manual and it's working.

  • Can I use the Ethernet Port for a computer when it is also used as a wireless network with an Airport Extreme as the access point for the wireless network

    Can I use the Ethernet Port  of the A1264 Airport Express to connect to the Ethernet port of a computer that does not have wireless capability when the Airport Express is also used on a wireless network with an Airport Extreme 5th generation as the access point for the network?
    I have AE 5th gen
    looking to buy (from ebay) the AEX A1264
    Various computers, printers and hubs for the network
    Is this possible to do?

    Bob, Thanks for the info. I have read different articles that said yes, but I wanted to make sure before I commit to buy. I have an older A1084 which I could not use the Ethernet port. I know at one point I was able to when I was on 10.4. Now that I am on an Intel processor and 10.8 I am going to have to upgrade some of my Apple wireless hardware.
    Thanks Again.

  • Can I use the Airport Express to connect to a Linksys Wireless Network and then use the Ethernet port on the Airport for a wired connection to a device for internet access?  Would I be able to then also use that Ethernet pt to a Ntwk Hub for more wired c

    Thanks for the help.  Looked but not clear on what I am trying to do as being possible.  Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it? 
    I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located.  Would prefer to replace Linksys with all Apple, but just not possible financially yet.  Thanks for the help.

    If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.

  • The ethernet port on the thunderbolt display is not working

    The ethernet is working when the cable is connected directly to my mac laptop but when connected the thunderbolt display there is no connection.  Is there some type of set up for the ethernet connection or can this port just be broken? 
    Thanks for the help! 

    Afterthought on an older post: it isn't immediately clear that the Ethernet port on the Thunderbolt Display works through the "Display Ethernet" interface, rather than through the "Thunderbolt Ethernet" interface. The latter was already present in the list of network interfaces in Network Preferences, while the former had to be added via the + button --- at least that was the case when I installed the TB display to work with my 15-inch MacBook Pro Retina this week.
    The AppleCare rep didn't know the difference either and agreed with me that it was puzzling that using the Thunderbolt Ethernet adapter on the Thunderbolt port of the display did work, wheras using the Ethernet port directly didn't (even though there were lights flashing on the Ethernet port of that other computer I tried to connect to in Internet Sharing mode). Close reading of the above posts made me go look for that mysterious "Display Ethernet" interface...  thank you Clinton!

  • Can I connect an external hard drive to one of the ethernet port of the airport extreme and access it from my Mac or PC?

    Can I connect an external hard drive to one of the ethernet port of the airport extreme and access it from my Mac or PC?

    If this hard drive is part of a NAS device, then yes it should be accessable from either a Mac or PC while connected to the AirPort Extreme Base Station (AEBS) by Ethernet.

  • Does the ethernet port work when the using airport express in client mode?

    I am considering using an airport express to extend my existing wireless network to a room where I can't get a cable to.
    I will need to connect a at least 3 devices to the airport express.
    The questions are:
    - is an airport express the right answer to this problem?
    - if so, does the ethernet port work (AE on client mode) as a passthru into the main network?
    - can I plug a hub to it?
    Thanks
    RFSF

    Hi Tesserax,
    Really appreciate you taking time to respond.
    I stopped by the Apple store this weekend and one of their sales people ( not one of their genius bar people) told me NO to all questions.  I tend to believe more answers from people in this forum but just realize that I have not mentioned one possibly important point:
    the main AP to which I will be connecting the airport express is not an Airport Extreme/Express AP. 
    Thanks,
    Ricardo.

  • Is there a device I can purchase to enable wifi on my old iMac, like something that plugs into the ethernet port?

    Is there a device I can purchase to enable wifi on my old iMac, like something that plugs into the ethernet port?

    Yes! There are lots of wifi adapters that will work with OS 9 on old iMacs. You can find a comprehensive list of them here:
    http://lowendmac.com/macdan/md09/mac-os-9-wifi.html
    Belkin seems to make a lot of wireless products for OS 9, so that would probably be the name to keep in mind. You can see one of these here:
    http://cache-www.belkin.com/support/dl/belkin_wireless_usb_network_adapter_manua l_os9.pdf
    If you're using an iMac G3, I think those are compatible with AirPort cards, so that's an option too. Good luck!

  • Airport express and the ethernet port

    Since January, I've had my older g/b model of airport express set to "join the network," which is an 802.11n airport extreme connected to my cable modem. Until last week, the ethernet port of the airport express could be used to connect in my DVD player or TV. I could do software updates on the DVD player, and watch youtube on the TV, etc. The connection became slow last week, so I decided to reconfigure the airports. Since then, the ethernet connection to the airport express is no longer recognized.
    Please note, although the airport express is not an "n" model, this set-up did work just fine! The DVD or TV was automatically able to display my IP address. The express has a green light, it has no errors in Airport Utility, and AirTunes still works just fine — it's only the ethernet port that has become completely inactive.
    Any thoughts?

    Not sure how you managed to do this with an 802.11g AirPort Express unless you had it configured to extend the wireless range of the 802.11n AirPort Extreme in a WDS. As far as I know, the ProxySTA (wireless Ethernet bridge) capability is only available with the 802.11n Express.

  • Can I use the ethernet port ....

    Can I use the ethernet port on the ATV to connect my blue ray p[layer to the internet using the ATV as a wireless card??
    If so how??

    I might be next in line on the airport extreme! Right now wireless is working better since the latest upgrade to iTunes, but hardwire is the way to go. Only problem is that ISP connections is in my office and my Home Media is downstairs. I was thinking of setting the Airport Extreme as a repeater in order to access ISP and then used the ports in the back for iTunes and ATV.

Maybe you are looking for

  • How do i install photo shop elements 11 on mac book pro with no disk drive

    i bought adobe photoshop elements 11 about a year ago. and want to install it on our mac book pro but not sure how to, as the mac doesn't have a disc drive , any information is greatly appreciated

  • Is there a way to prevent from text boxes to be numbered?

    Everytime I add a text box, it adds a number on the page for each one. Is there a way to prevent this? Thanks!

  • Mac Pro takes more time to boot than average

    Okay, well my Mac Pro (2008) takes anything between 40 and 48 seconds to boot (that's the time between pressing the power button and seeing the desktop with mouse movement). Being a long-time PC user, this boot time is MUCH faster than anything I've

  • To_date function hardcoding

    Hi All, I have a basic requirement. i need to run a query , so that the result time should be from 8pm yesterday to 8pm today. i need to mention the time in where clause, modifieddate between to_date('2007/05/23:08:00:00PM', 'yyyy/mm/dd:hh:mi:sspm')

  • LR5 on my two Macs

    I bought (and registered) LR5 in hard copy (disk) form.  I installed it on my iMac.  Since then I recently bought a Mac Book laptop without a CD slot.  Can I now download LR5 to my laptop?