Restart problem with kt4v motherboard

I have a kt4v motherboard with an athlon xp2600 processor and the whole computer just randomly reboots and then when it gets to the xp load screen(after bios set up) it rebbots again and again. can anybody tell me whats happening and how to sort it out?

The only way to find an answer is knowing much more about your PC: Video card ? Memory ? Power source ? O.S. ? Peripherals ? Heat sink ? and so on. Look at your Power Source about teh dif. Volts-Amp it gives and the brand. 8)

Similar Messages

I have a problem with my motherboard and my battery of my 2010 macbook pro 13". It was just serviced with a new screen, keyboard, and logic board.

I have a problem with my motherboard and my battery of my 2010 macbook pro 13". It was just serviced with a new screen, keyboard, and logic board. How much will a new battery and motherboard cost and would it be worth it or should I just get a new computer. It was about 300 dollars to get it serviced last week. if it adds up to much past 600 dollars I will just get a new one. THANKS FOR ANY HELP!
P.S During classes today it began beeping in my bag. Like three kind of long steady beeps then a short pause, and when I opened it I couldn't see anything but it was on so I turned it off and back on.

Depends on what options your Apple store offers - if they can do a depot repair (where they send it out), that's around $300 for all parts & labor.
If the store doesn't have that option, a logicboard is around $600, battery $80-$100, from what I've seen.
If they JUST replaced the logicboard, you absolutely should NOT have to pay for another replacement - the replacement is covered by a warranty. If they want you to pay for it, make sure you have a copy of the receipt for the work that was recently completed so you can show it to them. They have no reason to charge you for another logicboard.
~Lyssa

MOVED: I have problems with grafick motherboards MSI 845G max when i play games

This topic has been moved to Intel P4 & Celeron P4 based board.
I have problems with grafick motherboards MSI 845G max when i play games

There diff x4 agp and x8 agp.......... nothing!!!!!!!
Check you have INTEL application accelerator installed!!!!!!!
845GE-Max is very fast mainboard, only the single channel mem make's it slower than 865/875 chipset........ fact
Check ALL drivers are COMPAT with system NOT the latest............. Try older drivers
Del

Problem with KT4V

Hello.
I have a problem with my mainboard. How can i disable a sound from pc speaker at computer start?
When i On him, there are a lot of BEEP's and nothing happens. Then I must restart and everything is OK.
What can I do?
--sorry for my english-- ;(

You Need to count the beeps before you can find out what is or is not happening to your pc
This is a list of beep codes that will give you an idea as to why not booting, hope they help
1 short DRAM refresh failure The programmable interrupt timer or programmable interrupt controller has probably failed
2 short Memory parity error A memory parity error has occurred in the first 64K of RAM. The RAM IC is probably bad
3 short Base 64K memory failure A memory failure has occurred in the first 64K of RAM. The RAM IC is probably bad
4 short System timer failure The system clock/timer IC has failed or there is a memory error in the first bank of memory
5 short Processor error The system CPU has failed
6 short Gate A20 failure The keyboard controller IC has failed, which is not allowing Gate A20 to switch the processor to protected mode. Replace the keyboard controller
7 short Virtual mode processor exception error The CPU has generated an exception error because of a fault in the CPU or motherboard circuitry
8 short Display memory read/write error The system video adapter is missing or defective
9 short ROM checksum error The contents of the system BIOS ROM does not match the expected checksum value. The BIOS ROM is probably defective and should be replaced
10 short CMOS shutdown register read/write error The shutdown for the CMOS has failed
11 short Cache error The L2 cache is faulty
1 long, 2 short Failure in video system An error was encountered in the video BIOS ROM, or a horizontal retrace failure has been encountered
1 long, 3 short Memory test failure A fault has been detected in memory above 64KB
1 long, 8 short Display test failure The video adapter is either missing or defective
2 short POST Failure One of the hardware testa have failed
1 long POST has passed all tests

Problems with KT4V and AtiRadeon 9700 Pro...

Hi all,
I have lots of problems with my current configuration with games (lock ups) and even in normal use. Also I'm not able to run 3DMark through to see with kind of results would I get. Car chase (high) gets very low fps and the nature test doesn't even work. I have tried different 4in1 drivers and BIOS versions. With 1.6 BIOS version I had lots of CRC errors (should be corrected in BIOS ver. 1.7 but in expense of data rate?). Does anyone have any suggestions so that I could for example go through the 3DMark even with the expense of performance?
I had those game lock up problems also earlier with KT7A-100 RAID + AtiRadeon 64 (3DMark worked) so I bought new graphic card (didn't help) and after that I bought the new mobo. I know my config is not the best in the world, but I think it should be enough to give some happy moments in ever so demanding games... for a while...
There is also one thing that is quite strange. In my display adapters there is two drivers for AtiRadeon (primary in AGP and secondary in PCI)? I'm not expert, but isn't that weird? I have tried installing different drivers again and again (also reinstalled OS) with no luck! Trying to delete the secondary one doesn't help...
Help..........!
My specs:
MSI KT4V (MS-6712) 4in1 Hyperion 4.45, BIOS ver 1.0
AMD TM 1.2 GHz CPU
ATX pro3 (300W)
WIN 98SE
512 MB DDR (333)
SAMSUNG 40 GB (5400 RPM)
SAMSUNG DVD
ATIRADEON 9700 Pro (Club 3D) Catalyst 3.0
Soundblaster Live!

the 9700 is the most powerfull vga to date and needs power evan more than a gf4 4600
i would lbe looking at some think like an antec true powe 430 watt psu not a basic 300 watter
with ati,s own cards you need revision 1.3 as well best i can recall,but yours is an oem so im not sure
a search for 9700 in this section will get you lots of threads

Restart problem with cd in drive

So it all started when trying to close a program and the system wouldn't allow it. I tried to restart it but it wouldn't do it. So I shut it down by holding the power button. When restarting it sent me to a blue screen with the spinner, then eventually to a screen with the arrow...but nothing else loaded. An additional problem with this, is the cd in the disc drive, so I can't use reboot discs. I tried holding shift to send me to safe mode, but it didn't work. Then I tried to eject the disc using the mouse button. After I did this, when restarting, it sends me to a system needs to restart screen! So now I have the restart screen, and a cd in the drive! How can this be fixed!?

hi there-
try booting to open firmware holding apple-option-o-f and then type in the following command-
eject cd (hit return)
reboot (hit return)
then i suggest you try the steps outlined in this article for the blue screen. http://docs.info.apple.com/article.html?artnum=106464 if nothing else works, you will have to archive and install the operating system. here is an article which outlines that procedure. http://docs.info.apple.com/article.html?artnum=107120. you will have to reinstall third party software and do software update afterwards, but it will in almost every instance resolve the blue screen issue. good luck to you. [ 8 ) ]

Strange problem with KT4V

I have a strange problem with the board
when booting,the cdrw only blinks and can`t read cd`s.
I have tried swapping to another cd-rom,but still the same problem.I updated to the new bios (1.9)without problems.
my specs are:
KT4V
512MB PC2700
MAXTOR 80GB HARDDISK
MSI 52X24X52 CD-BURNER
MSI GeForce4 Ti4200 64MB DDR DVI

Quote
Originally posted by THE VIKING
I updated to the new bios (1.9)without problems.
When begun it to happen?
Before or after the BIOS update?

GF 5700 Ultra, problems with KG7 Motherboard

Hi,
My system specs are:
Athlon 1400 (t-bird, 133 bus)
KG7-lite motherboard
512Mb corsair memory (333, running at 266)
MSI geforce 5700 ultra
sound blaster live value
120 gig west dig, 80 gig western dig
I have had a fair few problems with this card, firstly it took me several hours to get it working. When i first put it in the screen was pretty distorted. I tried to install the latest nvidia drivers but they caused the screen to turn blank (signal but black screen) when windows came to the log on screen.
I reset my bios settings for my motherboard and got windows to boot although it was ni 4-bit colour mode. Eventually I was able to get the correct drivers installed and the card seems to be working OK.
When i turn certian settings on like "fast write" it causes the screen to blank out like previously mentioned.
Now its installed im not really satisfied with the quality but im putting this down to my fairly low spec CPU and motherboard which i hope to upgrade in the new year.
[edit] Morrowind, which is the only game i have tried, is now unplayable and i am unsure why. The graphics right from the first screen are distorted. [/edit]
anyone else had any of these problems and know if there will be any fixes for this?
cheers,
Seb

Seb,
The picture was exactly what I was looking for. You have everything bunched up on IRQ5. Your system does not have a chance of running correctly in that configuration.
your motherboard is too old to support APIC so you only get IRQs 0-15. To free up some IRQs, disable COM1, Com2, and Parallel Port if you are not using them.
You should not use PCI Slot 1 because it shares the IRQ with AGP Slot. You should not use PCI Slot 4 because it shares with the USB Controller. You should not use PCI Slot 5 because it shares with the Highpoint IDE Controller. The rest of the PCI Slots should be fine.
Make sure you load the latest Motherboard Drivers too.
Take Care,
Richard

IDE problems with KT4V-L?

Hi, I am trying to resolve a long standing problem with regards to cd/dvd drive issues - both with reading and burning. I have had a system based around the KT4V-L mobo for about 3 years now and about 2 years ago I started experiencing problems with my msi cdrw drive- problems reading and burning discs, both blank and written. I tried various possible solutions i.e. new cable, different ide placement, firmware upgrade, different burning software, via drivers, various WXP tweaks, mobo bios upgrade/tweaks, even a fresh XP install (vanilla xp pro) but nothing would stop me churning out coasters. I then thought that the drive itself must be faulty and swapped it for a new one only to have exactly the same problem. I limped on for a good while (everything else works just fine) until dual layer dvd burners got cheaper and decided to swap my cdrw for a samsung dl dvdrw. Still same problems... especially with dvds. Another fresh install of WXP pro (sp2) has yielded no improvement nor has trying mandrake linux (ver. 10). Anyhoo, my thinking now is that there may be a fault with the onboard ide controller although my HDD has always worked fine... As I said before, I have tried all the different placements/settings with regards to ide connections/cables/jumpers and bios settings.
Sorry to bang on for so long but it has been driving me slowly mad for a good while Any help gratefully received as I am on the verge of binning the mobo and just buying a new (different) one...
MSI KT4V-L (Bios ver. 1.9)
AMD Athlon XP 2200+
2 x 512 MB DDR PC2700
MSI GeForce4 440SE AGP8x (64 MB)
SoundBlaster Live! Value (CT4670)
HDD 0 Maxtor DiamondMax Plus 9 60 GB Ultra-ATA/133
TSSTcorp CD/DVDRW TS-H552B
Channel Well Technology 350W 3.3v - 20A, 5v - 35A, 12v - 17A
WinXp Pro SP2

Thanks for the response osnavi, the first cdrw drive was well under a year old when I changed it and had only had light to medium use. I agree that the power supply could be better but the fact remains that everything worked perfectly for the first year-ish. At that time I actually had another dvd drive alongside the cdrw with no problems until this issue arose- I then had to physically remove the dvd drive to get the cdrw working at all. I currently have my HDD as primary master and the dvdrw as secondary master but as I said previously I have tried all the various settings available. The HDD is running in ultra dma mode 6 and the dvdrw is ultra dma mode 2 - I did have to reset this as WXP had demoted it to PIO mode only, presumably due to multiple errors... Re. the power supply issue, is it possible that the system ran fine for a year (with slightly more load due to the extra dvd drive) and then just b0rked out? I have had no other issues at all with this system and I am a fairly application heavy user (photoshop, quark, fps games etc). Is it also possible that the upgraded bios may have caused the problem as I did flash it from the original OTB bios to version 1.9 as directed by the msi live update system?
Thanks again for your interest.
MSI KT4V-L (Bios ver. 1.9)
AMD Athlon XP 2200+
2 x 512 MB DDR PC2700
MSI GeForce4 440SE AGP8x (64 MB)
SoundBlaster Live! Value (CT4670)
HDD 0 Maxtor DiamondMax Plus 9 60 GB Ultra-ATA/133
TSSTcorp CD/DVDRW TS-H552B
Channel Well Technology 350W 3.3v - 20A, 5v - 35A, 12v - 17A
WinXp Pro SP2

I have problems with grafick motherboards MSI 845G max when i play games

I ask about apology my English not so good but I try toexplains my problem
I bought about year ago this motherboard .:::: MSI 845G Max .::::..
and i have at home this grafick card
asus Geforce fx 5700 li 128mb
The problem is .............
the picture intermixes when i play this games
fifa 2005, need for speed, pro evulation ................ and many from the games decaying with high grafick
I asked many persons and the sa that the motherboard grafick AGP plats is 4x
Hill of the games needs strength follows mother boards with 8x AGP
I uppdated my mother board in this page http://www.msi.com.tw/program/support/bios/bos/spt_bos_detail.php?UID=314&kind=1
to verion 1,6
But the update harbored is to old ::::::::: 2002::::::::::!!!!!!!!!!!!!!!!
Version 1.6 Update date 2002 - 12 - 17
I desire that you lice my problem with kind greeting of grateful with the respect and the estimate

There diff x4 agp and x8 agp.......... nothing!!!!!!!
Check you have INTEL application accelerator installed!!!!!!!
845GE-Max is very fast mainboard, only the single channel mem make's it slower than 865/875 chipset........ fact
Check ALL drivers are COMPAT with system NOT the latest............. Try older drivers
Del

Nokia 5800 Restart Problem with the Memory Card

hi,
i am facing a peculiar problem with my 5800.i hv firmware v21.
Whenever i restart the phone with the sd card inserted (it has around 35+apps/games loaded but 4.3GB of memory is free) ;the phone hangs up at the "nokia" screen & i hv to remove the battery.on ejecting the card & then restarting; the phone starts up fine.on inserting the card later after the restart; it is read without any problems by the phone & all the apps. work fine.i do not hv any apps loaded for start up.
i saw similar problems posted in some other topics for 5800;but could not get a clear idea whether this problem was occuring in other phones as well.Is it firmware related or due to large no. of apps on the phone?
please help.

it is most likely the corrupt memory card issue, it happens quiet often. that is why back up is so essential to have especially of memories and such. for that i use share online and upload my pics right away to ovi or vox whichever.
the programs you bought you should be just able to download once again and plug in the key you have gotten with your applicatioins. you should be able to recover all of your purchases. i am sorry for your pics for those can't be recovered
i always keep a separate email folder for all my application keys so i can find they easily as phones and memory does get corrupt. i can do it relatively quickly and have the info handy even on the go
Message Edited by radical24 on 22-Jul-2009 01:03 PM
You know what I love about you the most, the fact that you are not me ! In love with technology and all that it can offer. Join me in discovery....

Problem with KT4V mainboard

I have:
AMD athlon 1900XP+, MSI KT4V (not raid), 256MB DDR (333MHz), BARRACUDA IV 80GB, GF440MX etc. OS: WindowsXP Profesionall
When i plug second HDD (BARRACUDA IV 80GB) on secondary master and i want copy data with Primaty HDD to Secondary HDD my computer will restart ?(
HELP MEEEE!!!!![size=15]TaRuS[/SIZE]

Hi,
1. What is your power supply?
2. Did you place your hdds very close to each other? possible overheating can cause such error... make sure your drives get cool properly.
3. What are the jumper settings for the drives?
4. Is your WinXP from a clean installation? Or you did an upgrade on the motherboard without OS installation?
5. Does this occur to ALL data/file? Or just once in a while?

Restart problem with 5800 XM

Hi all,
i just buy nokia 5800 xm, and it was great...but i found a strange problem ! when i do servel prosses together like : open video + recive bluetouth , or open a music + browsing the internet....ext ) the phone sometimes suddenly restart ! and the screen slowly tun off, then the phone automatically switch on .
i try to update my phone software to the last ver 40.0.005 but the problem still !
what can i do ?
and what u think the problem is? software or hardware ?
btw im sure that ther is no virus especially i format the phone (hard format )
regards

It could be two reasons:
1. A system file on your card is corrupted, maybe a file for the task manager app. To check, remove the card, perhaps replace it with a newly formatted one and try to recreate the problem. If the problem does not occur if there is no card or using a newly formatted one, you need to either run a diskcheck on your old card, or if that fails, format it.
2. RAM issues. Some of your apps are memory leaking, and you arent able to manage your RAM properly. I would advise you to Google for tutorials on signing apps and look for Memcheck and KillMe.
If you find my post helpful please click the green star on the left under the avatar. Thanks.

Big problem with KT4V(MS-6712)

ok, i ordered two of these motherboards, for me and one for my friend, mine works fine, but his fails to boot properly, at first he was having problems booting up the computer at all, with an amd 2100+, and it wouldnt boot, he eventually found that when the graphics card was removed it booted, ok so the boards boots, what about graphics!, ive tried it with a geforce 2 ti and a geforce 4 4800 se, it boots, but the moniter is just left unstarted as if on "idle" there is no display on the moniter but the computer boots, my board works fine with these cards, any ideas what it could be, ??? or just a case of faulty motherboard?
any help much appreciated

well, i put the d - bracket in, and all four leds remained as red, which by the manual means
"System Power On"
- The D-LED will hang here if the processor is damaged or not installed properly"
ok fair enoguh, its the processor? - No, i tried a 1600+ in it which wouldnt work either, same result, "
oh , i just realised i forgot to put any RAM in when i just tested it, damn, will it still have gave no VGA output if no ram was in??? i also didnt plug in the speaker, just base - power switch and video card, so i wouldnt have heard any audial warnings, ok well i guess im gonna strip the computer out AGAIN :O and change the mother board AGAIN :O , urgh, ok well, if anyone had any idea what it would be, as i have tried it WITH RAM in the other day, but without the D-Bracket™2
thanks.

Restart problem with my Nokia 110

I got nokia 110 two months before. Suddenly after I tried to run a memory card it started restarting. I have tried to restore it but fone again restarts before the restoration has completed.I have successfully restored the device using *#7780# but problem still persists and while I am trying to restore it using *#7370# it restarts before it is completed. Kindly advise me how I can fix this problem.
Waiting for your kind reply as quickly as possible
Regards

Just Keep your phone Memory More than 5MB and delete some not important messages in your inbox (If accessible it's better to delete it all). Don't put any app on Homescreen Shortcuts and Goto Shortcuts (or any Shortcuts). By the way it is normal for a low ram phone to restart.
I love T9 Bar Phones | I used to be a Sony Ericson fan before but they leave the low end Phones so I have to switch to Nokia | LG Optimus L5 II and Nokia 206 3

Restart problem with kt4v motherboard

Similar Messages

Maybe you are looking for