Restore does not work without restart

iPod classic w/120 GB hard drive.  When I restore the ipod it will not show up in iTunes or my disk utility until I restart with the ipod plugged in.  If I run repair disk in the utility it finds a couple of errors and fixes them.  Next restore is the same.  I would like to give this to a friend but do not want to give them a headache.  If I put my ear to the ipod it makes a faint clicking sound.  This disappears once the problem resolves.  There is also a steady high pitched whine like the hard drives is running when it is plugged into the computer.  If I eject the ipod but leave it plugged in the drive stops spinning. Any ideas about wht the problem is?

Most likely your iPod hardisk is dying.
Do a Disk Diagnostic, as posted by tt2
https://discussions.apple.com/thread/3110831?tstart=240
This wont fix your problem, but it gives some idea., like getting some professional hardisk repair service or Apps.
Anyway, it would be a very bad idea, to give someone this problematic iPod as a gift to a friend, I would give it to someone I dont like, and let him feel your frustration.
Have a nice day!

Similar Messages

  • PCI wireless card does not work after restart - FM2-A55M-E33

    Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
    BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
    I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
    Does anyone know more about this issue?

    Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
    ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
    ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
    ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
    And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
    I am unable to find any useful information in the logs.
    Got any more suggestions?
    Thanks! (And sorry to disturb so much)

  • I have an iPhone 4 and everytime i try to go on safari, mail, or iTunes it does not work without wifi

    I have an iPhone 4 and everytime i try to go on safari, mail, or iTunes it does not work without wifi

    if your youtube was already running then I would exit out of the application completely by double clicking your home button and then search for your youtube app on the row that will show below and then press and hold down the youtube icon and then click the "X" to exit out of it. Afterwards try to reopen youtube and play a video to see if it works

  • Hello, all of a sudden I fell down my system and completely erased all bookmarks. Your progress with restoration does not work, send me ansver,please

    Hello, all of a sudden I fell down my system and completely erased all bookmarks. Your progress with restoration does not work, write me of bookmarks could not be loaded. Please advice on everything because I came and they seriously need it.

    Did your computer crash or did Firefox crash causing the loss of the bookmarks?
    You can check for problems with the places.sqlite database file in the Firefox Profile Folder.
    *http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
    *https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
    See also:
    *http://kb.mozillazine.org/Lost_bookmarks
    *http://kb.mozillazine.org/Firefox_crashes
    *https://support.mozilla.org/kb/Firefox+crashes

  • Microphone does not work after restarting computer

    I just received the Creative Xmod soundcard yesterday after using an Icemat siberia usb headset sound card for a couple months. The sound is a lot better with the creative soundcard however, if I restart my computer and go back into ventrilo, my microphone does not work. It doesnt make any sound when I talk into it (almost as if it muted itself) but it hasnt. I check my sound settings and everything is the way it should be.....but the mic isnt producing any sound. It is not my headphones that is causing the problem because I have never had this problem with my old icemat soundcard. I am currently using :
    Sennheiser PC350 headset
    Windows XP Home Edition
    The newest version of Ventrilo

    http://picsend.net/images/240403ventsetup.JPG
    That is how I have ventrilo setup. A friend of mine said I should Mux set to Record Control, but it only gives me the option for Wave In =/

  • User WF-BATCH and BAPI_PO_RELEASE does not work without printer assigned

    Hello Gurus,
    The function BAPI_PO_RELEASE is used in our PO approval workflow, but this one does not work till the user WF_BATCH has no printer defined in USR01-SPLD. This is a strange behavior because the output message assigned to the PO has a message transmission medium equals to 5 (External send) => not print.
    Does someone have already met the same issue?
    How this could be solved without assigning a default printer to user WF_BATCH?
    Kind regards
    Chris

    Hello Tison,
    we're using also the WF-BATCH user having no default printer assigned and it works fine with the final release.
    However, there's usually the output message NEU with a prerequesite maintained that the PO has to be finally released. So this way there can be an additional output message found upon releasing. But we have a printer assigned using the condition records and we're not using the type that you've specified.
    So I'd guess that, indeed, the problem lies within the message. You could copy the WF-BATCH user to a dialog user and release the purchase order in dialog and see what happends.
    With the very best wishes,
       Florin

  • XP windows restore does not work yet all is set correctly

    XP windows restore function does not work. All the restore points exist with descriptions of the changes that prompted them. It will let me select them (restore points) and restore process will strart but after rebooting it will ultimatly let me know that it could not restore.
    Does the Lenovo Restore and Rescue utility disable this function of XP ? ?
    Thanks

    Well I have a 6460-8WU that came with Vista and I got the downgrade CD set and tried to restore to XP.  The first time it said it failed to restore my system, but it seem to have XP and all the applications that I expected to see.  Later I had a problem with the Welcome Windows screen being unavailable... used only the Classic Windows Logon, I called Microsoft and they suggested using their system restore.... which didn't work at all... I tried 5 or 6 different backup files from different days and none of them worked.  At that point I decided to use the Lenovo downgrade CDs and format the hard drive restoring everything from scratch. It took me a few tries but eventually I did get it to say that it had successfully restored my system.  The items I learned from like 4 failed attempts to restore it are this:
    1.  Don't try to restore it while in the advanced dock.
    2.  When the restore process says to remove Disk # x and press OK, remove Disk # x-1 (the currently inserted Disk, and insert Disk # x, and then do not press OK until you wait 20 or 30 seconds or until the little icon of a CD that flashes when Windows reads a newly inserted disk has finished.  When I tried clicking OK either before I had actually inserted the next CD or too soon after I had inserted the next CD the process went downhill from there and failed to restore properly.
    3.  When it seemingly has read all the CD's and says it will now start the restoration process, but you are asked to press Next... well firstly there *is* no Next button to press and the other buttons other than Cancel are greyed out.  The solution there is to wait, and wait, and wait... so long that you may think the process has failed and the computer is hung... but it is not.  Eventually it will continue from that point.
    Aside from that, I notice that there is a new version of the Recovery Application on the Support site, but
    if you install the latest Rescue and Recovery 4.20.0511.00 in the readme there are 31 "considerations" listed, which are basically conditions under which it does not work properly or as expected, so I won't be trusting it to recover my system.  I will make a Paragon Drive Manager image after I get the updates all installed and use that to restore from.

  • DB Restore does not work on MSSMS 2014 under WIndows8.1

    When attempting to restore a DB which was backed up on a different machine (same names but SQL EXPRESS 2012) under MS 2014 running on WIndows 8.1 into a SQL Express DB, the following happens:
    1. Open Restore task
    2. Select Device to get 'Select backup devices"
    3. Invoke "Add" and expect to see a browser. Instead, a backup file location is indicated and no browsing is permitted in the "Locate Backup File" Even when the path and file names are just typed in, the Restore will not work.
    Any help is appreciated.

    Hi,
    SQL Server does not allow you to restore or attach a database from a higher version of SQL Server to a lower version of SQL Server in your case from SQL 2014 to SQlL 2012, however you can generate script in SQL 2014 and execute it on SQL 2012.
    How to migrate a SQL Server database to a lower version
    Please mark solved if I've answered your question, vote for it as helpful to help other users find a solution quicker
    Praveen Dsa | MCITP - Database Administrator 2008 |
    My Blog | My Page

  • Printer does not working after restart

    I have installed HP LaserJet m1120 using hplip and hplip-plugin from AUR.
    Everything was fine (printer worked) but after rebooting, printer doesn't working at all - cups doesn't "see" it and hp-testpage shows this:
    # hp-testpage -i
    warning: hp-testpage should not be run as root/superuser.
    HP Linux Imaging and Printing System (ver. 3.12.10a)
    Testpage Print Utility ver. 6.0
    Copyright (c) 2001-14 Hewlett-Packard Development Company, LP
    This software comes with ABSOLUTELY NO WARRANTY.
    This is free software, and you are welcome to distribute it
    under certain conditions. See COPYING file for more details.
    | SELECT PRINTER |
    Num CUPS Printer
    0 HP_LaserJet_M1120_MFP
    1 PhotoPrint
    Enter number 0...1 for printer (q=quit) ?0
    error: Unable to communicate with device (code=12): hp:/usb/HP_LaserJet_M1120_MFP?serial=MF12D9K
    error: Unable to print to printer. Please check device and try again.
    note: If an error occured, or the test page failed to print, refer to the HPLIP website
    note: at: http://hplip.sourceforge.net for troubleshooting and support.
    PhotoPrint is my second printer and it works fine.
    What should i do? I have been trying to configure it for long time...
    Last edited by Extravert (2012-11-17 14:46:06)

    Maybe, I haven't understood something but it still does not working.
    I found that journalctl outputs some errors
    Nov 17 22:57:06 trash-serv hp[405]: io/hpmud/pp.c 627: unable to read device-id ret=-1
    Nov 17 22:57:06 trash-serv python2[406]: io/hpmud/pp.c 627: unable to read device-id ret=-1
    And lsusb does not shows this printer
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Last edited by Extravert (2012-11-17 15:17:13)

  • Loss of sound (Hard-reset and restore does not work)

    Hi,
    I loss all sounds on my iPad 2 (currently on iOS 7.04). This is the 2nd time I have had this issue (had it with an earlier iPad) and had to replace the previous one (out of warranty period).  Very frustrating as it is about the same time period after purchase.  Last time, it seemed like a repeated fault with the iPad and I cannot believe I have the same issue again on a different product.  It is an expensive way of having to re-buy every couple of years for no other reason.
    It did not happen immediately after an update i.e. it does not appear to be "update" or iOS version-related. 
    Anyone got any advice please?  The facts are as follows (and what I have tried).
    When it happened?
    I was in iMovie editing a movie when all sound went from the speaker.  It continued to work with earphones plugged in, but this is now intermittent.  I have no sound on the speaker at all except for when I click sounds on the menu and change the level of ringer alert (which works on the speakers).  This seems to tell me that it is a software problem.  I have no sound on any applications or internet video or music from iTunes.  I cannot survive on the earphones as they only work for a period of time and then they fail (until I take the jack out again when it works again for a period of time before the headphones fail again).
    What have I tried?
    a) Numerous hard resets
    b) changing the side switch's position
    c) changing in general settings the side switch settings from lock rotation to mute and back again (repeatedly and in reverse to see if it makes any difference)
    d) resetting all settings - this made no difference
    e) erase all content and settings - interestingly at the stage when it asked me if I wanted to restore from an iCloud account, it was making sounds (the keyboard clicks - which don't make a sound irrespective of the click setting currently) i.e. appeared to have resolved the issue and as soon as I restored my iCloud back-up, the sound went again.
    I would be grateful for any suggestions.  This post also includes a recommendation to Apple on improving its product (relating to iCloud backups) as the ultimate solution should not be paying for a replacement for a software issue (to avoid losing all my data permanently).
    My musings are that:
    a) it is definitively a software issue (on account that the speakers work in certain situations only)
    b) it appears to be that the software is corrupted in my iCloud back up
    c) it is an issue that happens regularly and is an avoidable issue/cost to Apple's customers that needs to receive higher priority in being addressed as it is built in redundancy for a significant proportion of customers.  At the very least, iCloud backups should be capable of being restored in part - is there any way this could be done so we don't lose all of our notes, media etc if the final advice is to "start again".  How can it be right to lose all content because of an Apple system software issue?  I am pre-guessing this will be the final advice (if I don't want to pay for a replacement iPad)?
    Please help me and all those others with the same avoidable software problem.
    Thank you,
    Peter

    This is an iPad user to user forum, so you are not addressing Apple.
    Try this  - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.)
    Check your settings. The iPads have a small switch on the right edge. It can be used as a rotation lock to keep the screen from automatically reorienting itself as you move around, but you need to have the tablet’s settings configured properly. That same switch, right above the volume buttons, can also be set to function instead as a mute button to silence certain types of audio.
    If the switch is set to work as a mute button, you can change its purpose to “screen-rotation lock” by tapping the Settings icon on the home screen. On the Settings screen, tap General on the left side, and on the right side of the screen flick down to “Use Side Switch to.” Tap to select Lock Rotation or Mute to set the button’s function. Even if you set the side switch for your preferred use, you can still mute the Mini or lock the screen. Just double-click the Home button, and when the panel of apps appears along the bottom edge of the screen, flick the row from left to right with your finger. Tap the icon on the far left side of the row to either lock the iPad’s screen or mute the iPad’s alerts, notifications and sound effects. Music, podcasts and video are not muted unless you turn the volume all the way down.
    iPhone: Can't hear through the receiver or speakers
    http://support.apple.com/kb/ts1630
    http://www.atreks.com/app-no-sound-on-ipad-4-%E2%80%93-what-to-do/
     Cheers, Tom

  • Tried to upgrade the software and my phone crashed...restore does not work

    What do I do?! I tried to upgrade and it stopped at the verifing software...it went to the screen with the USB plug and the Itunes icon. When I try to restore it stops at the same point on the preparing to restore and goes to verifing software. What do I DO! (Iphone)

    Without more information all I can suggest is:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       

  • DFU and Restore does not work

    Firstly, I would like to point out that I am using the latest version of iTunes.
    My girlfriend gave me her phone to fix. She has tried to install iOS 7 which does not appear to have worked and she did not make a backup.
    When the phone is switched on, the 'Swipe to Setup' message appears. You select a language etc and then are greeted by a message advising to connect the phone to iTunes. When you do this, iTunes basically advises that there is an issue.
    I sucessfully started DFU mode and iTunes then recognised that there was a phone in recovery mode and shows the restore button.
    After clicking the initial resore button, I am then offered the 'Update and Restore option which I selected.
    iTunes then shows the phone being restored:
    Restoring iPhone software...
    Verifying iPhone Software...
    Verifying iPhone Restore...
    Restoring iPhone Firmware...
    It then tells me it is complete and to leave the phone connected which I do. After a few minutes, iTunes detects the phone and tells me once again that there is an issue. The phone itself, as before; shows the 'Connect to iTunes' message after going through the initial setup of language etc.
    Can anyone offer any advice as to what is going wrong with this?
    I have tried this procedure no fewer than seven times and it is becoming quite frustrating.
    Any help would be very much appreciated.

    Go elsewhere. JB voids the Apple warranty and means you will get no support from Apple, including from this Apple forum.

  • System restore does not work!

    I am running Windows 7 upgraded from Vista and I am having issues in the little flag that pops up in the task bar on the right side.
    It says that disk errors are detected, when i try to fix it nothing happens. I tried to restore my computer and I keep getting this message that
    "Windows has detected file system corruption on (my hd). You must check disk for errors before it can be restored"
    I go to run the disk check and when I do not have automatic fix it actually scans, but tells me after a while that I need to click the automatic fix file system.
    I do that and it says "Windows can't check disk while in use. Do you want to check for hard disk errors the next time you start your computer?"
    I click schedule but nothing happens when computer restarts.
    Any help would be appreciated.

    Ill post you some screen shots can you over here ill try to link them.
    I go to restore 1.
    http://i25.tinypic.com/2wdxboz.jpg
    2. I go next and select a point to restore
    http://i28.tinypic.com/1zwhopz.jpg
    [IMG]http://i28.tinypic.com/1zwhopz.jpg[/IMG]
    3. I get error
    http://i26.tinypic.com/29vn95.jpg
    [IMG]http://i26.tinypic.com/29vn95.jpg[/IMG]
    4. I check for errors and get this
    http://i28.tinypic.com/64nl3b.jpg
    [IMG]http://i28.tinypic.com/64nl3b.jpg[/IMG]
    5. the schedule thing pops up
    http://i32.tinypic.com/11m84nk.jpg
    [IMG]http://i32.tinypic.com/11m84nk.jpg[/IMG]
    MarantzI tried that earlier and it still did not run after restart.
    I searched these forums and they had a vista fix I tried to use that since my original windows was vista but that didnt work for me. In that they had the chkdsk r and stuff nothing worked

  • Application not working without restart the blackberry

    Dear All, when i get connected through WiFi , the only app working is the browser and the reset of the applications not working , and after restarting the blackberry phone every thing working fine for just 24 hours then it come back down again and i need to restart again , so could any one help

    mohammedzico1 wrote:
    the only app working is the browser and the reset of the applications not working , a
    Specifically, what other applications are not working? Name them.
    Do you have a BlackBerry Data Plan enabled on your account with your carrier or mobile provider? You must, in order to get the RIM push email functions you are looking for, as well as additional BlackBerry data services such as the internet browser, Facebook for BlackBerry, BlackBerry Messenger, and much more.
    1. If any post helps you please click the below the post(s) that helped you.
    2. Please resolve your thread by marking the post "Solution?" which solved it for you!
    3. Install free BlackBerry Protect today for backups of contacts and data.
    4. Guide to Unlocking your BlackBerry & Unlock Codes
    Join our BBM Channels (Beta)
    BlackBerry Support Forums Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Uppdated to 18.0.2 and suddely all my bookmarks are gone. Restore does not work.

    Hi There. Just updated to 18.0.2 and all my bookmarks (16 years!!!) are gone. Tried restoring but Firefox says it can't read the files.
    What to do?
    Best / Michael

    Problems with bookmarks and history not working properly can be caused by a corrupted places.sqlite database file.
    You can check for problems with the places.sqlite database file in the Firefox Profile Folder.
    *http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
    *https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
    You can also try to reboot the computer or run Firefox once as Administrator.

Maybe you are looking for