Restore message appears after waking iPod from Hibernation

For the past week, every time I wake my fifth generation iPod from hibernation, I get a message telling me to connect my iPod to a computer to restore it. This message will disappear after a minute or so and the screen will go dark. If I press a button after this happens, the iPod will go thru the reset process (apple logo appears and it reboots itself). After this it is fine until I leave it long enough for it to go into hibernation again, in which case the whole process starts over. I've been afraid to connect it to my computer for fear I'm going to lose all my music. Has this happened to anybody? Any suggestions?
iBook G4   Mac OS X (10.4.9)  

A BSOD can be caused by anything. Hardware, software, firmware, drivers.
What is the BSOD code?
You should see a 0x000000xx number, and a System File such as win32.sys

Similar Messages

  • After waking up from Hibernation: Wireless mouse and k'board dont work!!

    Hi All
    My second issue with my iMac, otherwise been a good experience. This is the annoying one. Sometime, or i should say most of the time, when the iMac wakes up from Windows XP hibernation, the mouse and the k'board (both bluetooth wireless) decide not wake up!! sometimes they do (and i suspect it is the time i quickly double click the left button on the mouse before the windows screen comes up) and sometimes they wake up after 5 minutes!! most of the time i dont have the patience and I just reboot which is very annoying! anoyone knows why?
    I saw a set up in the bluetooth devices where I can tick/untick a selection asking me if i want to to turn off the blutooth to save power (this is under control panel/system/hardware/bluetooth/properties) do i need to untic this?
    Many thanks

    Seems like im truly the only one with the problem but i did find a workaround. When coming out of hibernation/standby (ie after u press the power button) u start double clicking the left mouse button like a possesed man!! just keep double clicking till you hear the (ding ding, ding ding), click a couple more times and that should wake up the mouse and k'board.
    If u notice, when windows starts (from normal start up), mouse doesnt wake up till u double click the left button. Same issue here, seems blue tooth has a short window when coming out of hib/s.by and if u miss it then all freezes.
    Well hope this helps some other people who got this issue.

  • Hi this message appears after 2 hours downloading Mavericks : an error occurred while extracting files from the package "mzps4135638417199433253.pkg"

    Hi this message appears after 2 hours downloading Mavericks in App Store :
    an error occurred while extracting files from the package "mzps4135638417199433253.pkg"
    Same with "CMD + R"
    Help...

    It sounds to me like your Internal Hard Drive is failing.
    I recommend you buy a new one, that is a good candidate for replacing the old one, but install it in an External enclosure and Install a fresh Mac OS X on it from the DVD. You can boot your Mac from any attached drive.
    The new System can be used to get some work done, check your emails, and takes the pressure off resolving this immediately. You can also attempt to salvage files off the old drive if needed.
    Once things seem to be working, then move the new drive inside the computer. Failures at this point may be due to bad cable, which has been a problem in some of these MacBooks.
    Use security erase, write Zeroes, one pass, to re-write every block on the old drive. Any block discovered to be bad will be replaced with spares the drive holds in reserve for this purpose. If more than 10 blocks are pared on one pass, "Initialization Failed!" will be the result. Although you can try the erase again, there is some question whether you want to trust this drive with your precious data.

  • Hello, I have a macbook pro late 2011 15 inch with 4 gb ram. My macbook runs extremely slow when logging in after waking up from sleep, locking up and I am unable to use the keyboard. Is there a fix?

    My macbook runs extremely slow when logging in after waking up from sleep, locking up and I am unable to use the keyboard. Furthermore, when just using safari to watch streaming television, my computer gets really slow, and locks up, and the dock appears blank and I sit here frustrated. Anytime i wake up my computer, my keys don't respond and I've waited at most 3 minutes untill i can type in my password. Even sometimes when i type in my password and hit enter, it takes forever to open up my mac. I have barely used any storage in my macbook, since i only use it for college, and I have run clamscan wiht no viruses showing... Any ideas?

    when just using safari to watch streaming television, my computer gets really slow, and locks up, and the dock appears blank
    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, or by a peripheral device. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output andWi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Question I have a dilemma . I added a lot of songs in my iTunes now when I synced my ipod this message appear "Elma's ipod cannot be synced because there is not enough free space to hold all the items in the iTunes library (additiona

    I addesd a lot of songs in my itunes, now when I synced my ipod this message appear "elma's ipod cannot be synced because there is not enough free space to hold all the items in the itunes library (additional 382m is required). Then I uncheck a lot of song and synced my ipod again same message appeared. Do I need to buy a new ipod with more memories? Somebody told me to check apply after I unchecked some of the songs but I cannot find the word APPLY. please help I'm not a very technical person.

    The Sync button becomes the Apply button, if you change the iPod's settings in iTunes.  If you are only unchecking songs in the iTunes music library, you click on the Sync button.
    When you select the iPod in iTunes, you see the iPod's Summary screen on the main part of the iTunes window.  There is a checkbox there for Sync only checked songs.  Did you check that checkbox?  If you want iTunes to ignore the songs you unchecked when syncing your iPod, that setting needs to be enabled.  If you change that setting, you'll see the the Sync botton has changed to Apply.  Click Apply.
    That method of unchecking songs works, but it may become annoying over time, as you need to uncheck more and more songs.  If you want advice on some other more convenient ways to make it work, you can post back.

  • Ethernet interface disappears after waking up from sleep

    Hi guys,
    I've been trying to debug a networking problem without any luck and I think it's about time I ask the forum for help.
    My ethernet interface no longer works after I wake up my computer from sleep. I have no idea why.
    Before sleep:
    # ls /sys/class/net
    lo wlp2s0 enp3s0f2
    After waking up from sleep,
    ls /sys/class/net
    lo wlp2s0
    Here are the list of services I have running.
    UNIT LOAD ACTIVE SUB DESCRIPTION
    dbus.service loaded active running D-Bus System Message Bus
    [email protected] loaded failed failed dhcpcd on enp3s0f2
    [email protected] loaded active running Getty on tty1
    [email protected] loaded active running Daemon which acts upon network cable inse
    kmod-static-nodes.service loaded active exited Create list of required static device nod
    [email protected]\x2dSecure.service loaded active exited Networking for netctl profile wlp2s0-Wolf
    polkit.service loaded active running Authorization Manager
    systemd-backlight@acpi_video0.service loaded active exited Load/Save Screen Backlight Brightness of
    systemd-fsck@...\x2d38bc68d942fc.service loaded active exited File System Check on /dev/disk/by-uuid/1c
    systemd-journald.service loaded active running Journal Service
    systemd-logind.service loaded active running Login Service
    systemd-random-seed.service loaded active exited Load/Save Random Seed
    systemd-remount-fs.service loaded active exited Remount Root and Kernel File Systems
    systemd-sysctl.service loaded active exited Apply Kernel Variables
    systemd-tmpfiles-setup-dev.service loaded active exited Create static device nodes in /dev
    systemd-tmpfiles-setup.service loaded active exited Recreate Volatile Files and Directories
    systemd-udev-trigger.service loaded active exited udev Coldplug all Devices
    systemd-udevd.service loaded active running udev Kernel Device Manager
    systemd-update-utmp.service loaded active exited Update UTMP about System Reboot/Shutdown
    systemd-user-sessions.service loaded active exited Permit User Sessions
    systemd-vconsole-setup.service loaded active exited Setup Virtual Console
    upower.service loaded active running Daemon for power management
    [email protected] loaded active running User Manager for 1000
    Furthermore, plugging in the ethernet cord after the computer has started doesn't connect to the internet, even when I have the ifplugd service running. I am forced to run:
    sudo ip link set enp3s0f2 up
    sudo dhcpcd enp3s0f2
    However, I can't run these commands after the laptop wakes up from sleep since it no longer sees the ethernet interface.
    I am thoroughly confused. Please help me.

    It seems to be fixed after the kernel update. On an related note, I've switched from using dhcpcd to netctl. I've enabled netctl to automatically connect to the network using:
    # systemctl enable [email protected]
    # systemctl enable [email protected]
    So when I check for the status of the ethernet profile, I get told that's it's inactive.
    #netctl status ethernet-dhcp
    netctl@ethernet\x2ddhcp.service - Networking for netctl profile ethernet-dhcp
    Loaded: loaded (/usr/lib/systemd/system/[email protected]; static)
    Active: inactive (dead)
    Docs: man:netctl.profile(5)
    But I turned off the wireless, so I must be connected to the ethernet, So how do I know which profile I'm connected to?

  • HT4859 How do I restore my apps to my ipod from icloud?

    While I was updating my ipod touch 4 on my PC, my ipod was disconnected all of a sudden. I had to restore it. My data and info was backed up to icloud, but all my apps disappeared. How do I restore my apps to my ipod from icloud?

    File>Transfer Purchases

  • W510 eSATA/USB2.0 combo port does not respond after waking up from sleep mode

    Has anyone tried to connect external DVD/CD player or burner to the eSATA/USB combo port and experienced very slow system performance after waking up from sleep mode?  It might takes minutes to launch an application program that usually takes just few seconds.  My W510 can not even restart.  It will just stop at the Thinkpad logo if I tried to restart after waking up from sleep.
    The funny thing is if I moved the external DVD/CD player to the USB2.0 port in the back, everything went back to normal.  I don't know if this has anything to do with the fact that the combo port has something to do with eSATA.
    Thanks

    It seems that this problem is unique to my system. I am hoping that one of the Mac Guru's will have at least a pointer in the right direction.
    Thanks.

  • After I make a trailer or movie on my Iphone 4S and try to save it to the camera roll, I get a message that "an error occurred during export".  The message appears after the piece has seeminly finished exporting.  What am I doing wrong???

    After I make a trailer or movie on my Iphone 4S using IMovie and try to save it to the camera roll, I get the message "An error occurred during export."  The message appears after the piece has seemingly finished exporting.  What am I doing wrong????

    I appreciate you taking the time to copy and paste boilerplate responses to increase your points in this forum, but I've already read all those support articles in depth; but you have barely read my post at all. Please don't guess a fix. Only someone with the latest versions of iMovie, iOS, iPhone, Yosemite, and MacBook Pro is qualified to troubleshoot this, because anyone would immediately see that the following option no longer exists:
    Open iMovie on your Mac, and choose File > Import > iMovie for iOS Project.
    Read my post before you reply: It clearly says in the title and within my post that I can neither export nor import through iTunes without receiving an error message. So your response neither solved my question nor helped me whatsoever.

  • Touchscreen stops working after waking up from sleep

    Touchscreen stops working after waking up from sleep sometime it not working at all.
    IT encore2 WT8-B32CNM

    If you can't solve your issue and no one in the community can help, contact support to speak with a tech support agent at (800) 457-7777.
    - Peter

  • Why does my Mac screen suddenly go dark? Sometimes it stays dark for an indefinite period after waking up from sleep.

    Why does my Mac screen suddenly go dark? Sometimes it stays dark for an indefinite period after waking up from sleep. I have to open and shut the monitor screen to get it to light up again.

    Might try posting in the MacBook Pro laptop forum. This is the Mac Pro desktop forum.
    Also see:
    OS X: When your Mac doesn't sleep or wake

  • Lose connection to external USB hard drive after waking up from sleep

    My Mac lost connection to the external USB hard drive after waking up from sleep. I can still see the folders in the hard drive in Finders, but when I double clip a folder no file within the folder is displayed. I have to reconnect the hard drive with iMac to read its contents.
    May I ask how this happens and is there a solution?
    I'm using Paragon NTFS for Mac OS X to read from and write to NTFS format of USB external hard drive.
    Thanks!

    ... I un-ticked the "put hard disks to sleep when possible" option in the Energy Saver panel in the System Preferences, and it seems the problem is solved. will have to sleep and wake up my iMac to further verify if this is the solution ...
    Alternative advices are always greatly appreciated!

  • Track pad freeezzzz after waking up from sleep mode

    HI
    i have OS X Ver 10.5.1
    i have enough ram, disk space, and have the 2.4 GHz Core 2 Duo processor.
    but when my mac wakes up from sleep the track pad is just not behaving properly, i.e it keeps jumping positions and freezes until i restart. if this continues it will be very frustration to use leopard.
    also i did not get the option to archive and install at the installation so i cant even down grade, this is one of those time i trusted that everything will go right and looks like the problems just begun.
    please help me !
    Vinod

    Hi,
    I have almost the same problem with my T540p, except that there is no internet connection not only after waking up from the sleep mode, but also when starting windows and sometimes the internet connection will get suddenly lost during normal windows run.
    I tried installing all kinds of drivers - latest from intel, latest from lenovo update (which is always different version from the one from intel), some older versions. Nothing helps.
    Re-enabling the WiFi device like Aaziz1982 suggested, doesn't help.
    Here is a more detailed description of my problem: http://forums.lenovo.com/t5/T400-T500-and-newer-T-series/T540p-WiFi-Connected-no-internet/m-p/177818...
    Does anyone have other suggestions?
    Thank you,
    Pavel

  • HT201263 Hi, how can I restore my ipod when this message appears after trying to restore "this device isn't eligible for the requested build"

    Hi,
    My kids disabled my ipod touch and I've followed the directions on line but when it comes to restoring the following error message appears, any point son how to fix this?

    iOS: Restore error 3194 or 'This device isn't eligible for the requested build'

  • Invoice Receipt Warning Message Appear After Upgrade from 4.6C to ECC6

    Hi Gurus,
    We do upgrade from 4.6C to ECC6. And we do Invoice Verification base on Delivery (Vendor delivery number), in our business process there more than one Purchase Order has same Vendor Delivery Number while GR executed. But only one Purchase order related to Invoice verification, others PO are Free PO (no need Invoice Verification).
    The problem is:
    In SAP 4.6C, while execute Invoice base on Delivery (Vendor delivery), system automatic select only PO with Delivery (vendor) which related/allow invoice receipt.
    In SAP ECC6, while execute Invoice base on Delivery (vendor delivery), all PO selected. So than there are warning messages appear (warning pop screen) for those PO not allow invoice Receipt (message M8035: PO item XXXXX does not allow invoice receipt), and at the end PO which allow Invoice receipt then appear for further Invoice Receipt process.
    At overall, the final result SAP 4.6C and SAP ECC6 is same (only PO which allowed Invoice Receipt will processed further).
    The Question are:
    1. Why in ECC6 appear warning message, while in 4.6C no warning message ? Is there config to ignoring the warning message. I've try to maintain system message for M8035 (t-code: OMRM) to ignoring the pop screen, but can not created.
    2. How do we make warning message dissapear (no need warning message), because if the PO's has hundred items so user need to click enter hundred times.
    Thanks in advance.
    Regards,
    Tri Wicaksono

    Hi,
    could you please check whether the flag "GR-based IV" is set in the purchase orders?
    If GR based-IV is ticked, then this pop-up cannot be suppressed.
    If you would like to post the invoice first then GR-based IV should not be checked, otherwise this pop-up will always appear.  I am afraid that this behaviour is standard. 
    Please, be aware that this feature is only available if you set  in the Purchase Order item the 'GR-based IV' indicator:
       If the GR-IV flag is not set in the PO, then the system does not                     
       differentiate individual goods receipts. Please see the <f1> help                    
       for the field "GR-IV" in the PO item detail. Since the individual                    
       receipts are not differentiated, an invoice is not tied per se to                    
       an individual receipt and a goods receipt can be reversed despite                    
       an invoice receipt.                                                                               
    With the GR-IV flag set on in a PO, you can specify which goods                      
       receipt is being invoiced in an IR and which goods receipt is being                  
       reversed in a return. It is this correlation between goods receipts                  
       and invoices that enables you to specify for GR-IV PO's whether an                   
       item can be returned despite an invoice. 
    Please refer to the note :457511 Question 10.          
    Best regards
    Erika

Maybe you are looking for