Restoring iphone3 an unexpected error.

Restoring iphone3 an unexpected error.
Restore begins and when it's nearly finished the unexpected error shows.
I've retried a number of times.
Downloaded newest itunes and checked USB attachment, restarted computor.
After a few trys the phone goes completly dead, but wakes up when i conect it to the charger.
Then I tryed to restore again withe the same resutl.

Hi,
The error here didn't help much.
Please first take a try with what britishdhez suggested.
If it happens again, please click on the advanced tab and post the full error messages here. And please have a share about which wizard you were trying to run, to troubleshoot what?
In addition, please also take a check into Event Viewer to see if we could get any errors to track with.
Best regards
Michael Shao
TechNet Community Support

Similar Messages

  • After updating to itunes 10.4 restarted, my ipod touch went into restore mode. when trying to restore it says unexpected error occured (1604) followed resolution checklist . still wont work, any thoughts............

    After updating to itunes 10.4 restarted my pc windows 7 64 bit, my ipod touch 3rd gen went into restore mode,when trying to restore it works for several minutes then says it cannot be restored, unexpected error occured (1604) I have followed the reslution checklists, still wont work, any thoughts?

    Hi
    Cannot offer any thoughts other then i am having the same problem. updated my itunes windows7 32bit ipod touch 4th gen. went into restore mode lost over 700 songs. i dont get any error messages i just cannot get into itunes store. Firewall is allowing access, etc resolution checklists done, and nothing.
    Hopefully this issue is fixed up soon...

  • When restoring an iPhoto library I got an "unexpected error" message and the operation could not be completed. Is my best choice to try again?

    One of my external hard drives died. I had several iPhoto libraries in it. Fortunately, I used Time Machine to backup to a Time Capsule and I can see all the iPhoto library icons in Backups.
    When restoring the first iPhoto library, after three hours, I got an "unexpected error" message and the operation could not be completed. Indeed, the restored library is smaller than the library in Backups. Is my best choice to try again and replace the restored library (which apparently must be missing some photos)? It would mean another 3 hours plus of restoration with fingers crossed...
    Any suggestions? Thank you in advance!

    I am always suspicious of using a different OS to the one that was used to run the backup.. ie if you used Snow L to backup then there is absolutely nothing wrong with using SL to restore.
    Mount the TC sparsebundle and verify it using disk utility.
    A5 here. http://pondini.org/TM/Troubleshooting.html
    You might also like to load the widget in Time Machine so you get whatever the full error message is..
    I cannot find any reference to the error code you are getting..
    My recommendation would be to try it on a different computer.. restore the whole backup to an external drive large enough to accept the whole backup.
    Use the manual methods pondini recommends.
    http://pondini.org/TM/FAQ.html
    Q16 17
    Use ethernet only. Turn off wireless so it does not enter the situation.

  • HT201210 I get the following error message when trying to restore seeting: unexpected error occurred (3014). anyone will be able to help please? thanks

    I get the following error message when trying to restore settings on my iphone:settings could be restored due to an unexpected error occurred (3014). anyone will be able to help please? thanks

    Did you ever figure out the problem? "Contact Software Manufacturer"?? That sounds ominous... I've got the same issue and I'm pretty durn aggravated right about now....
    Thanks!

  • HT4623 my ipad wont restore after trying to upgrade software, now says Unexpected error (3) ....?

    After trying to update software on my ipad it now will attempt to restore but gets to the end and says unexpected error (3)?? any ideas how i can solve this?

    the 3 is in brackets (3)? Before that it says unexpected error has occured...
    I cant remember what version we were on before updating.
    I have just purshased a new computer and down loaded the latest version of itunes and still have the same problem...
    My iphone updated fine...

  • Unexpected error -600 with iTunes?

    I recently got a new HD and restored from backup and updated to 10.4.9. When I first updated to 10.4.9, I started getting app not responding messages with iTunes - it would have the arrow in the dock and the toolbar was listed but then would stop responding. I re-installed iTunes and it got better but still happens every few days. I can force quit in the Finder but the triangle stays under the icon in the dock. I can force quit with Activity Monitor but then if I try to open the app from the applications folder, I get a -600 unexpected error. Anyone have any idea what's happening? Sometimes it doesn't respond but then eventually (minutes later) works. Sometimes it opens no problem. Sometimes I have to restart to get it to respond.

    I am getting the same error but it happens when i'm synching my ipod with itunes

  • HT201250 i'm getting message: can't be opened because you don't have permission to see its contents. and he operation can't be completed because an unexpected error occurred (error code -8003).

    I took my computer in to have the Backup restored onto my computer after having a new harddrive put onto my 1year 1/2 old MacBook Pro. When i got it home there was a new User that i had to logout of to getting into my normal user. Don't know why this was, just figured the Mac guys that installed my backup did this for some odd reason. Today i could not open any of my files in the backup on the time machine. All the folder had line going thought them and when i clicked on them I revieved this message: can’t be opened because you don’t have permission to see its contents. After talking with that same mac store. I decided to just delete all the files out of the time machine as it was just put back on my computer and i have everything i need. Hours later when i tried to empty the trash i got this messsage: the operation can’t be completed because an unexpected error occurred (error code -8003).
    Any advise how to fix my problem?
    thanks in advance

    While you see a single trash can, in reality there are trash folders on each mounted volume.  I don't use TM but what you are describing implies that a TM drive is no different with the way trash is treated.  So when the TM is unmounted the trash folder on there is gone and thus the trash looks empty.  Remount the drive, the trash folder on it now causes the trashcan to look like something is in it.
    If TrashIt! could not remove the file, I'm sorry, you will need to use the terminal.  We can do this one step at a time so you only have to copy/paste the lines into terminal (except the first time).  So launch Terminal (in utilities).  You might want to make the window that is shown a bit larger with the grow box since it's pretty small.
    This first line is the only exception to the copy/pasting since you have to enter some information.
    sudo ls -laR /Volumes/your-TM-volume-name/.Trashes
    where your-TM-volume-name is the name of your TM volume.  That's the part you have to fill in since I don't know it.
    When you hit return the sudo in that command will cause a prompt for your admin password.  Enter it and hit return again.  Note the password will not be shown as you type it.  Post the results so I can tell you what to do next.
    Note this ls command is not doing anything but listing the files in the TM's .Trashes folder.  Remember I said each drive has it's own trash folder.  .Trashes is it.

  • OLAP Error:The underlying connection was closed: An unexpected error occure

    We have recently installed BPC 51 (SP2). This been working fine for months until yesterday. Now we are getting errors on OLAP Database. Following is the problem description. Any help would be appreciated.
    Received error "The underlying connection was closed:  An unexpected error occurred on a send." while processing dimension. This message appears during 'Create Dimension' sub step( step 2/5). After this BPC server crashes.
    The same error appears while deleting appset during 'Delete OLAP Database' sub step (step 2/4). We are also not able to restore an appset since the process hangs during OLAP Database stage.
    Software version: BPC Version 5.0.102 SP2
    MS SQL Server 2005
    Microsoft SQL Server Management Studio      9.00.3042.00
    Microsoft Analysis Services Client Tools      2005.090.3042.00
    Microsoft Data Access Components (MDAC)      2000.086.3959.00 (srv03_sp2_rtm.070216-1710)
    Microsoft MSXML      2.6 3.0 4.0 5.0 6.0
    Microsoft Internet Explorer      6.0.3790.3959
    Microsoft .NET Framework      2.0.50727.1433
    Operating System      5.2.3790
    Thanks

    Yes we did that several time, but did not solve the problem.
    Finally, we processed all the dimensions, applications, appsets within SQL server studio and the problem is resolved. I am not sure if this would surface again.
    Thanks
    Edited by: Sankaranarayanan Janakiraman on Jun 19, 2008 8:34 AM

  • IPod nano had unexpected error syncing

    Hi
    Yesterday whilst syncing my iPod Nano 5G with iTunes 10.3, I recieved an unexpected error message from iTunes telling me that nine files had corrupted and that my device needed to be restored. I have not restored the device yet but now whenever I connect my iPod to my PC windows asks me to scan the device for corrupted files and iTunes asks me to restore.
    If I Restore the iPod will I lose the built in games that were on the device when I purchased it or any other important data which can't be retrieved afterwards?
    Thanks

    Update: After again repeating the 5Rs (instead of re-install, downloaded latest version of iTunes which prompted for "repair" rather than "install"), a message asking me if I wanted to update my iPod software came up. I accepted, and following the install was able to sync without the "corrupted" message. Of course when the sync was finished, I tried to play my iPod and noticed that there was no music on it (so in fact the sync hadn't really worked). Since then, all I get when connecting the iPod is the "corrupted" message, even after another reset.
    Suggestions?

  • Downloading from the App Store the message "There was an error in the app store.  Try again later (4)'. Then 'unexpected error'.

    Downloading from the App Store the message "There was an error in the app store.  Try again later (4)'. Then 'unexpected error'.
    I've been getting this message now for the last couple of days.  I can download other apps on my phone with the same apple ID but have now experienced this on my Mac firstly when downloading Yosemite immediately after being asked for my ID password, and then having tested with a couple of other apps, so it's not related to the download.
    I'm using OS X 10.9.5 on a Mac Book Air.
    I've shut down on a number of occasions and tried again
    App Store is version 1.3 (201.7)

    Back up all data before proceeding.
    Triple-click anywhere in the line below on this page to select it:
    /Library/Preferences/SystemConfiguration/NetworkInterfaces.plist
    Right-click or control-click the line and select
              Services ▹ Reveal in Finder (or just Reveal)
    from the contextual menu.* A folder should open with an item selected. Move the selected item to the Trash. You may be prompted for your administrator login password. Restart the computer and test. If there's no change, restore the item you deleted from a backup, overwriting the one that may have been created in its place. Otherwise, you may need to recreate some of your settings in the Network preference pane.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
              Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
    Credit for this solution to ASC member luis.pinho.

  • I tried to to the ios update to my 4S phone. itunes says there was an unexpected error. now my phone is hung on a screen which show a usb cable and an arrow pointing to the itunes icon. i cannot reset the phone, everytime it appears to reboot it comes bac

    I tried to update my 4s to the latest ios6. itunes came back and said there was an unexpected error. the screen on the phone is hung showing a usb cable and an arrow pointing to the itunes icon. itunes does not see the phone as being plugged into my computer. I restarted itunes, no difference. I can't seem to reset the phone. It comes up with the apple icon and then goes back to the usb plug screen. I'm totally hosed right now!!!

    Error 1604:
    This error is often related to USB timing. Try changing USB ports, using a different dock connector to USB cable, and other available USB troubleshooting steps (troubleshooting USB connections. If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
    If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
    Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
    Restore and wait for the error.
    When prompted, click OK.
    Close and reopen iTunes while the device remains connected.
    The device should now be recognized in Recovery Mode again.
    Try to restore again.
    If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
    From Apple Support page >
    iTunes: Specific update-and-restore error messages and advanced troubleshooting

  • Unexpected error when trying to reset Firefox sync

    Hello,
    I am trying to reset my password for Firefox sync with no success. When i enter my email address and hit "next" i get "Unexpected error". I don't want to create a new account with a different email address.
    Any help is appreciated.

    Hello jc_denton,
    The Reset Firefox feature can fix many issues by restoring Firefox to its factory default state while saving your bookmarks, history, passwords, cookies, and other essential information.
    '''''Note:''' After resetting Firefox, you will lose any extensions, toolbar customizations, and some preferences.'' See the [[Reset Firefox – easily fix most problems]] article for more information.
    To Reset Firefox:
    # Open the Troubleshooting Information page using one of these methods:
    #*Click the menu button [[Image:New Fx Menu]], click help [[Image:Help-29]] and select ''Troubleshooting Information''. A new tab containing your troubleshooting information should open.
    #*If you're unable to access the Help menu, type '''about:support''' in your address bar to bring up the Troubleshooting Information page.
    #At the top right corner of the page, you should see a button that says "Reset Firefox" that looks like this: [[Image:Button reset]]. Click on it.
    #Firefox will close and reset. After it is done, Firefox will show a window with the information that is imported.
    #Click Finish and Firefox will reopen.
    Did this fix the problem? Please report back to us!
    Thank you.

  • 'An unexpected error occurred' using AirPort Utility to configure an Extreme

    Hi all, I've been fighting with this problem for a while. I have a 2011 Mac Mini running OS X 10.7.5 and AirPort Ulility 6.2. I also have a new-ish AirPort Extreme A1408. They've never really seemed to work properly together. The only way to configure the device is to manually launch the AirPort Utility, go "file > configure other" and enter the password "public" to log in and manually change the settings.
    If I hard-reset (which I've been doing to troubleshoot another issue) and simply choose "Other AirPort Base Stations (1)" I can see my router in the drop-down. It goes through the process of gathering information and joining the default wireless network (I'm using the unsecured default right now as a matter of fact), but then the process ends with 'An unexpected error occurred'. Even with that message displayed, the default wi-fi connection stays up (clicking cancel kills the wi-fi connection immediately).
    I can always go back through the "file > configure other" process and set it up manually, but then it never appears in the AirPort Utility as a connected base station - all I see is a green light for Internet and a "No configured base stations have been found" message.
    Here's what I'm seeing in the Console:
    13-05-25 11:12:27.000 PM kernel: MacAuthEvent en1   Auth result for: 20:c9:d0:20:4c:10  MAC AUTH succeeded
    13-05-25 11:12:27.000 PM kernel: wlEvent: en1 en1 Link UP virtIf = 0
    13-05-25 11:12:27.000 PM kernel: AirPort: Link Up on en1
    13-05-25 11:12:27.000 PM kernel: en1: BSSID changed to 20:c9:d0:20:4c:10
    13-05-25 11:12:27.889 PM configd: network configuration changed.
    13-05-25 11:12:27.914 PM UserEventAgent: CaptiveNetworkSupport:CaptivePublishState:1211 en1 - Probe
    13-05-25 11:12:27.914 PM UserEventAgent: CaptiveNetworkSupport:CaptiveStartDetect:2322 Bypassing probe on Apple Network 204c0f because signature is in the known good cache
    13-05-25 11:12:27.915 PM UserEventAgent: CaptiveNetworkSupport:CaptivePublishState:1211 en1 - Unknown
    13-05-25 11:12:27.923 PM configd: network configuration changed.
    13-05-25 11:20:29.000 PM kernel: wlEvent: en1 en1 Link DOWN virtIf = 0
    13-05-25 11:20:29.000 PM kernel: AirPort: Link Down on en1. Reason 8 (Disassociated because station leaving).
    13-05-25 11:20:29.795 PM UserEventAgent: CaptiveNetworkSupport:CaptivePublishState:1211 en1 - PreProbe
    13-05-25 11:20:29.806 PM configd: network configuration changed.
    Looks like after I open AirPort Utility, the connection to the default wireless network is established, the system goes to probe the base station, says "nope I know this guy already", then the process spits out the 'An unexpected error occurred' message, I click "cancel", and the link is dropped.
    Does anyone know why my AirPort does this? Is it a network configuration setting somewhere in the Mac? I've had this thing for a while and of course decided to dive into the Apple ecosystem entirely dropping to a single Windows gaming rig, only to find that the special magic doesn't work for me

    Read this please, before assuming your AirPort Extreme is broken. The links at the end will likely resolve your issues. First try to rollback your AirPort's firmware to 6.1.1, which should restore your Internet connectivity. If it does, but you'd rather have the most recent upgrade available, follow the steps given in the following links, 6.1.3 should work fine for you then.
    After numerous attempts by apple IT reps to persuade me that my modem was somehow the cause of my AirPort Extreme broadcasted WiFi network suddenly losing connectivity after the 6.1.3update, I found the truth that helped me to correct my own problem, and successfully use 6.1.3 rather than the rolled back version 6.1 i had been forced to resort to.
    If rolling back your Airport's firmware fixes your connectivity issue, or your dns server has been erased by the update to 6.1.3, I speculate that these links will help you out greatly.
    It turned out, that this was A KNOWN ISSUE to Apple! With an actual fix Published by Apple themselves! They've just got it hidden away because they must have wanted to drive me to the brink of insanity. . Luckily for Apple I worked with an amazing rep *(Thelma) who at least acted as if she didn't think I was a crazy person. I found the fix on my own after 16 grueling, redundant and fruitless, hours of troubleshooting (time wasting) with "senior" Apple techs.
    Let me tell you, 'I told you so' has never sounded so sweet. (Thelma) was ****** that no one in the company bothered to fill her in on this issue or solution and had her support send me a new AirPort just before I discovered the fix. After the discovery, she told me not to bother sending either back, and apologized for the run around that took up weeks of my life.
    With out further ado and with thanks to Softpedia for posting the info-
    http://news.softpedia.com/news/Airport-Time-Capsule-7-6-3-Affects-IPv6-Tunneling -328680.shtml
    http://news.softpedia.com/news/Apple-Releases-Fix-for-IPv6-Tunnel-Error-Under-Ai rPort-7-6-3-331186.shtml
    *name(s) changed to protect the competent
    AirPort Extreme 802.11n (5th Gen), iOS 6.1.3
    I have this question too (1) Reply Categories: Airport Extreme Tags: airport_extreme, firmware, airport, ipad, wifi, 4, router, extreme, multiple_devices, internet_access, update_error, dns_error, amber_light, no_dns, 6.1.1, roll_back, 6.1.3

  • Struggling to figure out reasons behind those "An unexpected error has occurred" messages in SharePoint 2010

    We are in day 5 of using SP 2010 on our 4 server farm. The farm was created by taking our MOSS 2007 databases and attaching to our database.
    We have had a variety of cases of users encountering the "An unexpected error has occurred". In perhaps 10% of the cases, we have found the correlation id in the logs - which are tracing using the default logging levels.
    We have used the Merge-SPLogFile and get-splogeven cmdlets but get no records returned for the others.
    They are not occurring frequently. But when they do, we don't have a lot to go on to figure out what is wrong.
    I have read various other threads on the site. I have looked in all of the 14 hive logs on all 4 servers (which should not be necessary after having used merge-splogfile) but do not find the correlation anywhere. I have used uls viewer - still do not find
    it.
    This is a production system where users are making use of the system 24x7. I need to find things to try that do not take down the system.
    Is there any way that increasing the verbosity of the logging might be requried so we can see these errors?

    It truly depends on the error that occurs, but I would say that increasing your logging level would be the first place to start.
    BE AWARE... Setting logging levels to Verbose WILL fill up drive space very quickly, so if your servers don't have much free drive space, you run the risk of crashing the server when it runs out of space... in the very least, server performance will grind
    to very poor levels.
    If you're not finding the correlation IDs, then upping the level might be the only way to get the messages.  The best approach is to try and find a recreatable scenario.  If you can recreate the error through UI actions, you can up logging levels
    on an App server (to avoid impact on end users) and point directly to that App server (using HOSTS entries) in order to recreate the error.  Once you've recreated the error, you can restore normal logging levels on the server again and then proceed to
    parse the logs using ULSViewer in order to find the target correlation ID.
    I trust that answers your question...
    Thanks
    C
    http://blog.cjvandyk.com |
    LinkedIn | Facebook |
    Twitter | Quix Utilities for SharePoint |
    SharePoint Admin Nav Console (SPANC)

  • Unexpected error occurred - Try Again

    Hi,
    I upgraded my Time Capsule from a 500GB disk to 2TB Seagate Barracuda
    After resassembly and re-start the following occures
    I attempted to Erase the new disk, unexpected error occurred - Try Again
    I completed a hard factory reset
    The Time time capsule is found by the Airport Utility, try to configure a new wireless network the same error occurs
    Tried to update the firmware earlier before the factory reset, still the same problem.
    Running out of ideas
    Thanks

    Hi,
    Didn't think it was going to be that simple ....
    I just upgraded to the latest 27" iMac, I had a USB drive attached for backups which was getting very noisy and annoying.
    The master plan was to upgrade the 500GB TC, with a 2 TB Drive (fail by the look of it now) and use the upgraded 2TB TC for iMac and the MacBook Air backups and remove the Noisy USB.
    I have now purchased a new 2TB TC, because the wife wasn't getting any WIFI at the front of the house (she was getting irate) ... as wives do LOL.
    So now I need to revert the TC back with the old drive, to restore to working order.
    I will then sell the Old TC and get something for it ... :-(
    Use the 2 TB drive for a customer upgrade which has happended to come along now.
    Thanks for your HELP

Maybe you are looking for

  • Create external window in Web Dynpro Java

    Hello experts, I am new in web dypro java as well as enterprise portal. I have a problem concerning external window. I have created a button in my ivew in web dynpro java. By a click on this button, I would like to open an external window with a spec

  • Excise Tax Indicator

    Hi While Configuring CIN i came across Excise Tax indicator in that fields are empty i have to make an entry in order to configure i like to know IMG Part where to make an entry for that Excise tax indicator for vendor Classifies the vendor for the p

  • My computer crashed and i lost itunes. redownloaded itunes if i erase and snyc my ipod to my computer will i l;ose everything on my ipod?

    when i go into itunes in the library it shows all my music i purchased but not the music i put on there with cds i had. if i erase and snyc it to this computer will i lose all that music and everything i purchsed???

  • Financial Report Template for Trial Balance

    Dear All,       I was prepared the financial report Template, for trail Balance as per Schedule VI (6) after completation of template i exucute the trail balance by the using of above template. For the execution of the above report i used the selecti

  • Not able to compress project made in FCP4 - HELP

    Totally frustrated - 3 weeks behind schedule. We've made a project in FCP4 on our eMac with 512 RAM. We've made other projects in the past, but not this long. This is 1 hr, 55 minutes, with lots of transitions, moving titles made in LiveType, and aud