Restrictions for Unencrypted VLANs in 1200

Hi,
Is it possible to set simultaneously two unencrypted (Open/No WEP)VLANs/SSIDs in an AP?
I have an environment where VLAN 10 is "Open/No WEP" for BBSM authentication, but I also need to create a second "Open VLAN" that will have direct access to the Internet, without BBSM authentication for some specific and provisory situations (this VLAN would not be connected to BBSM).
Are there any restrictions for that? Is it possible to set two or more unencrypted SSIDs or an "Open/No WEP" SSID and a Guest SSID?
Rgds

Hello KaSing,
Are the following combination of encryption methods compatible on a single Access Point:
1. LEAP with Broadcast Key Rotation
2. LEAP with Cisco WPA (CKIP/CMIC)
3. LEAP with WPA (TKIP/MIC)
4. Static WEP using any available Key Slot
The documentation states that you cannot use Broadcast Key Rotation concurrently with Static WEP, since WEP slots 2 and 3 are used by the rotating broadcast keys. It also states that LEAP/EAP uses slot 4.
If Broadcast Key Rotation uses slot 1 as the transmit "seed" key, permuted in slots 2 and 3, why can't this static key still be used in slot 1 by a static WEP client?
Does static WEP preclude the use of any other dynamic WEP encryption/cipher? What other encryption scheme can interoperate with static WEP?
Thanks Dixon!

Similar Messages

Field Bline date is a required field for G/L account 1200 122400

While posting a Good receipt document using MIGO for a PO I am recieving the following error
Field Bline date is a required field for G/L account 1200 122400
Though both the document date and Posting date fields are filled with appropriate date.
The detailed message reads as follows, now my question is how to change the baseline date for the Cocd 1200 for GL account 122400
Field Bline date is a required field for G/L account 1200 122400
Message no. F5 808
Diagnosis
The value for field "Bline date" in the interface to Financial Accounting is an initial value but you are required to make an entry in the field selection for G/L account "122400" in company code "1200" linked to the field selection for posting key "81".
System Response
Error
Procedure
It might be an error in the configuration of the G/L account field selection. The initial application, used to call up the interface must otherwise define a value for field "Bline date". If this is the case, contact the consultant responsible for the application used to call up the interface or get in contact with SAP directly.

Hello Ravinagh,
Heres what I did:
OB41> Double clicked on posting key 81> clicked on field status> Payment transactions> Both Due date and Value date have already been set to optional.
For OB14 it asks me to input a field status variant.
There are three of them. Now here is the tricky part, how do I find out which field variant has been assigned
0001     Field status for 0001
1000     Field status for CoA 1000
3000     Field status for CoC 3000
I went further and check for all the three variants one by one
and found out that in the field status> Payment transactions for the following entry in the field status group
G045     Goods/invoice received clearing accounts
The DUE DATE and VALUE DATE are suppressed. What do I need to do here?
Next I checked OBB8 to find the following three Options I dunno which one of them is applicable to the GL account 122400 for Cocd 1200. Where can I find the assignment? How can I find which payment term is being used.
   PayT        Sales text
Day limit   Explanations
0001
0           Payable immediately Due net
0002
0           Within 14 days 3 % cash discount
              Within 30 days 2 % cash discount
              Within 45 days Due net
0003
15          Within 14 days 2 % cash discount
              Within 30 days 1.5 % cash discount
              Within 45 days Due net
              Baseline date on 30 of the month
Entry 1 of 40
Well I went ahead and clicked on each of them
For 0001 the Default for Baseline date is set to Posting date (Do I need to change anything here?)
For 0002 the Default for Baseline date is set to Document date (Do I need to change anything here?)
For 0003 the Default for Baseline date is set to Posting date (Do I need to change anything here?)
Please guide me here. If you need screenshots I would be glad to mail it to you.
I hope you understood the scenario.
Thanks
Ron

How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?

Hi All,
Hope to you a very happy new year,
I have two differnt LAP 1300 and 1200 in my network and I need to add theme to the WLC,
I successed to add one of theme by the option 60 in the DHCP pool at the Core SW,
So my quetion is below:
How to use multiple VCI strings for lap 1300 and 1200 (option 60) in one pool?
Thanks in Advanced,
Ahmed,

To add to Scott's post. Option 60 would be useful if you needed to put certain types of AP on specific controllers. Otherwise, no real need to use it for the most part.
Though, I do recall an issue a few years ago that some windows machines had issues getting DHCP if option 43 is being returned.
Now, on an IOS switch, you can only configure one option 60 per DHCP scope
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Email name restrictions for icloud

What are the name restrictions for creating a new name for an iCloud email account. Can one use some of the keyboard symbols like * # & % ! - $ __ ( ) or are you restricted to using the alphabet and numbers?

Hello Tuffy Wuffy,
This can be done by removing the iCloud account, then readding it.
On your iOS device’s Home screen, go to Settings > iCloud, then at the bottom of the screen, tap Delete Account.
iCloud: Change iCloud feature settings
http://support.apple.com/kb/PH2613
Cheers,
Allen

Access restriction for PDF generated with Smartform

Hi there,
I am generating a PDF from a Smartform using convert_otf.
What I would like to do is, add restrictions for the generated document just like in Acrobat Professional.
For example:
Printing: yes/no
saving: yes/no
cut, copy paste: yes/no
Is there a way to pass this Parameters to the PDF?
Thanks in advance
Uli

Hello,
check this thread: Mailing PDF Attachment with Password Protected
Otto

User ID restriction for Project/WBS to create service entry sheet

Dear All,
My client requirement is that the user id should be restrict for particular project or WBS to create service entry sheet(ML81N). Can we do it in this manner?
Further i want to give you my organization structure as given below.
1. Project :- 20
2. Plant :- Single
3. Bus. Area:- 2
4. Co area :- Single.
Thanx,
Vishal Kr. Sharma

Standard restriction is possible for this T code based on document type,purchasing group,purchasing org and plant.
Others being ruled out I think solution is to restirct using purchasing group which is smaller entity.
Regards
Sreenivas

Restriction for the use of last_record in 10g forms

Hi,
When I was working on Forms 6i with the query in the trigger When_new_form_instance:
go_block('ABC');
execute_query;
last_record;
first record;
go_block('DEF');
execute_query;
last_record;
first record;
It worked and gave correct data on frontend.
When the same was used in 10g forms, it gave incorrect data.When we removed last_record from the query, it worked.
Could somebody tell me is there some kind of restriction for the use of last_record in 10g forms? If yes, what kind of?
Thanks,
Neha

When I set Query All records to Yes.
Surprisingly it gives incorrect data.
This is what is bothering me.
As i said earlier i was using last_record for
navigation purpose to fetch all the records from the
database and then first_record to highlight the first
record.
You don't need to do that, that is poor programming logic. Instead change the block property Query All Records and set it to Yes.
This will fetch all the records from the database and the highlight will be on the first record;
Regards,
Tony

Restriction for Profit centers

Hi All,
I have an issue here. The client wants the following requirement:
A set of users needs to be given access to post all the GLS available in FBCJ, wherein the users should get restricted at Profit center level.
Manual posting through FB50, Fb01 and F-02 should not get affected with this. They have been using validations for this till now.
How do i go ahead with authorisation object in this scenario. If authorisation object and roles can be used in this, please tell me in detail what all objects i need to use for GLs, PCs, Tcodes and User Names.

Friends,
         What i found out is we cannot have both hierarchical and flat restriction for one role.The following scenario best explains that..
      let us say we have restricted 0PROFIT_CTR for values P001,P002,P003 and at the same time we have restricted on hierarchy.
      Through this we can succesfully restrict queries which have flat list display of Profit center but for the queries which display result in hierarchy it fails because the query that is framing up for hierarchical display is having the following condition in its select statment
           0PROFIT_CTR=;
        for which we are not authorized.
    So we can have only either Hierarchical restriction or flat list restriction for one role.
     Please if anybody find it incorrect I request them to share their knowledge with me.
Hansjörg Luzi thanks for the help.
Thanks & Regards
Mrutyunjay

Access Restrictions for Time?

I keep trying to set access restrictions for my wrt54g router for time. There is no 12 for time so I'm selecting 11:55 pm to 6am but I keep getting an error message of, "end time must be bigger then begin time." I get this no matter if I select 9pm, 10pm, etc.........
Any ideas?

You cannot choose a time frame through midnight. You have to split it in two rules, one before midnight and one after, i.e. choose 12am to 6am and 9pm to 11:55 pm.

Cisco Catalyst 6500 version 12.2(33)SXI13 configured as DHCP server for a VLAN responds to Windows 7 client with status code NOA

Can anyone help figure out why the Catalyst 6509 is not able to assign an IPv6 address? Thank you.
Cisco Catalyst 6500 version 12.2(33)SXI13 configured as DHCP server for a VLAN responds to Windows 7 client with status code NOADDRS-AVAIL(2). My configuration on the 6500 for the DHCPv6 server is:
ipv6 dhcp database disk0://DHCPV6-DB
ipv6 dhcp pool VLAN206IPV6
prefix-delegation pool VLAN206IPV6-POOL
dns-server 2620:B700:0:1001::53
domain-name global.bio.com
ipv6 local pool VLAN206IPV6-POOL 2620:B700:0:12C7::/65 65
interface Vlan206
description *** IPv6 Subnet ***
ip address 10.2.104.2 255.255.255.0
ipv6 address 2620:B700:0:12C7::2/64
ipv6 nd prefix 2620:B700:0:12C7::/64 14400 14400 no-autoconfig
ipv6 nd managed-config-flag
ipv6 dhcp server VLAN206IPV6
standby version 2
standby 0 ip 10.2.104.1
standby 0 preempt
standby 6 ipv6 2620:B700:0:12C7::1/64
standby 6 preempt
I'm getting a result from my debug as follows:
Apr 10 16:28:02.873 PDT: %LINK-3-UPDOWN: Interface GigabitEthernet2/2, changed state to up
Apr 10 16:28:02.873 PDT: %LINK-SP-3-UPDOWN: Interface GigabitEthernet2/2, changed state to up
Apr 10 16:28:02.877 PDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet2/2, changed state to up
Apr 10 16:28:03.861 PDT: IPv6 DHCP: Received SOLICIT from FE80::5D5E:7EBD:CDBF:2519 on Vlan206
Apr 10 16:28:03.861 PDT: IPv6 DHCP: detailed packet contents
Apr 10 16:28:03.861 PDT: src FE80::5D5E:7EBD:CDBF:2519 (Vlan206)
Apr 10 16:28:03.861 PDT: dst FF02::1:2
Apr 10 16:28:03.861 PDT: type SOLICIT(1), xid 8277025
Apr 10 16:28:03.861 PDT: option ELAPSED-TIME(8), len 2
Apr 10 16:28:03.861 PDT: elapsed-time 101
Apr 10 16:28:03.861 PDT: option CLIENTID(1), len 14
Apr 10 16:28:03.861 PDT: 00010001195FD895F01FAF10689E
Apr 10 16:28:03.861 PDT: option IA-NA(3), len 12
Apr 10 16:28:03.861 PDT: IAID 0x0FF01FAF, T1 0, T2 0
Apr 10 16:28:03.861 PDT: option UNKNOWN(39), len 32
Apr 10 16:28:03.861 PDT: option VENDOR-CLASS(16), len 14
Apr 10 16:28:03.861 PDT: option ORO(6), len 8
Apr 10 16:28:03.861 PDT: DOMAIN-LIST,DNS-SERVERS,VENDOR-OPTS,UNKNOWN
Apr 10 16:28:03.861 PDT: IPv6 DHCP: Option IA-NA(3) is not supported yet
Apr 10 16:28:03.861 PDT: IPv6 DHCP: Sending ADVERTISE to FE80::5D5E:7EBD:CDBF:2519 on Vlan206
Apr 10 16:28:03.861 PDT: IPv6 DHCP: detailed packet contents
Apr 10 16:28:03.861 PDT: src FE80::21D:E6FF:FEE4:4400
Apr 10 16:28:03.861 PDT: dst FE80::5D5E:7EBD:CDBF:2519 (Vlan206)
Apr 10 16:28:03.861 PDT: type ADVERTISE(2), xid 8277025
Apr 10 16:28:03.861 PDT: option SERVERID(2), len 10
Apr 10 16:28:03.865 PDT: 00030001001DE6E44400
Apr 10 16:28:03.865 PDT: option CLIENTID(1), len 14
Apr 10 16:28:03.865 PDT: 00010001195FD895F01FAF10689E
Apr 10 16:28:03.865 PDT: option STATUS-CODE(13), len 15
Apr 10 16:28:03.865 PDT: status code NOADDRS-AVAIL(2)
Apr 10 16:28:03.865 PDT: status message: NOADDRS-AVAIL

Hello,
maybe hitting the following bug.
Pv6 Address Assignment Support for IPv6 DHCP Server
CSCse81385
Hope this helps

802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment

Currently Being Moderated
802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment
Could someone please provide me with a simplest set of configuration steps to fire up Radius in ACS and 802.1X for dynamic vlan assignment. The objective is to roll out NAC L2 OOB using the 802.1X method for dymamic vlan assignments.
If possible show:
1. ACS/Radius Configurations.
2. End User Switch Configurations
Variables:
Switch A
MAC Address aaaa.bbbb.cccc     Vlan 10
            bbbb.cccc.dddd     Vlan 20
Also, if someone posts the Pros and Cons of using Radius/ACS/802.1X for Dynamic Vlan Assignments.
Other technology sets that can be used for Dynamic Vlan assignment EXCEPT from deprecated/obsolete VMPS.
Thanks in advance. .

Hi Guys,
    Hmmm, well if your just looking for Mac based authentication the good news is that is very easy. Just set create your Radius server, ACS, FreeRadius, Steelbelted radius etc. Then create user with the name of the Mac address, in other words if the mac address is 0012.0021.1122 the the name would be 001200211122 and the password would be the mac address. Then you set the vlan and tunnel stuff, like so tunnel-Type would be vlan, Tunnel-medium would be 802 and Tunnel-Private-Group-ID is the name of the vlan(not the vlan number)
   So for the Cisco ACS 4.x you would create a user as specified above, fill in all the password boxes with MAC address, I believe the mac has to be all lower case in the name and the password. Then check the Separate(Chap/MS-Chap/ARAP) box. Then you pick the group the machine belongs to, the group is the part that defines what vlan it is on.
   Before you create the user, create the group with info I wrote above and in addition specify the Service-Type as Authenticate Only.
    Freeradius is a bit harder to configure the specifics and I am just now testing a freeradius server so I do not know the process for Machine authentication.
    If, however, you are trying to authenticate a user that gets a bit trickier and is not so straight forward.

DLSW ethernet redundancy for multiple vlans

Can dlsw ethernet redundancy support mutliple vlans with the following configuration?
host dlsw router1 host dlsw router2
| |
local dlsw router 1 local dlsw router2
| |
ethernet switch1-------ethernet switch2
Ethernet switch1 and 2 are supporting multiple vlans and connected to local dlsw router1 and 2 through 802.1Q. SNA support is required for the vlans of ethernet switch1 and 2 .
We found that configuration of dlsw ethernet redundancy is not allowed on the 802.1Q sub-interface of the local dlsw router1 and 2. In this case, how can dlsw ethernet redundancy can be supported for SNA server attached to multiple vlans? Can you provide us some reference / sample for dlsw ethernet redundancy to support SNA servers attached to different vlans in a switch environment.
Thanks.

I think that I understand the problem. I am thinking the following:
dlsw local-peer peer-id 2.2.2.2 promiscuous
dlsw transparent switch-support
interface Ethernet0
mac-address 0000.3333.3333
dlsw transparent redundancy-enable 9999.9999.9999 master-priority 10
dlsw transparent map local-mac 0000.6666.0000 remote-mac 0200.eca2.0000 neighbor 0000.5555.5555
interface Ethernet1
mac-address 0000.4444.4444
dlsw transparent redundancy-enable 9999.9999.0001 master-priority 10
dlsw transparent map local-mac 0000.6666.0001 remote-mac 0200.eca2.0000 neighbor 0000.7777.7777
Of course, you need an ethernet interface per VLAN. If you need DLSw ER over dot1q interface, please contact the local Cisco Sales Rep or partner. You are not the first one to ask for it. Hope that there is a strong business case to initiate the new feature.

WRT54GS Access Restriction for WiFi Connected Devices

I have the WRT54GS v4 running with the latest Firmware Version: v1.06.3 -- I am attempting to add Access Restrictions for a few MAC addresses and IP addresses (my kids iPod Touch and laptop).
I am simply wanting to deny total internet access from 9pm to 7am. I have gotten it to work but ONLY for computers that are actually plugged into the router (cat 5 internet cables). All the computers/devices that connect to the router via wifi do not seem to be restricted at all. I am thinking this is an issue with the router in that it ONLY seems to apply the Access Restriction rules to those devices that are actually directly connected by hardwire.
Has any one else noticed this issue for WiFi connected devices? Access Restrictions do not seem to apply to WiFi connected devices.
Please help -- I would hate to have to buy another router.

Are you sure you have enter the correct MAC address or IP address? Wired connections use different MAC and IP addresses then wireless connection...

Quantity restriction for Customers in Sales Order

Hi all,
Please advice on priority basis,
I have one requirement, we want to have quantity restriction for product & specific customer in sales order. system should not allow more than the defined quantity for product to particular customer. We dont have the contract process.
regards

Hi,
This can be achieved by the condition type.
Go to V/06 and copy PR00 and made the new condition type.
Now this will be your main condition type which will carry out pricing.
Assign this condition type to your pricing procedure and save it.
Make this condition type mandatory and remove it from PR00.
Now go V/06 and select your newly created condition type and click on detail.
Over there you will find condition update just click on that.
Condition type : C quantity basis.
Do these setting for your condition type.
Now go to VK11 and enter the condition type and store the data first.
Then click on extras u2013 additional data or press F7.
Over there you will find max condition base value.
Enter the total number of value which you want to sell to your customer.
Now every time you create order this value is getting updated for your customer for that material.
So when it reach the limit which you set then this condition type will be deactivated.
And because this will be mandatory condition type so with out this you wont be able to create the sales order.
Itu2019s a little bit confusing language hope so you will understand.
If you have any problem then let us know.
Regards
Raj.

Is exist restriction for select-options.........?

is exist restriction for select-options?
for example:
<b> data: ftxt04(4).
select-options: txt04 for ftxt04.</b>

Hi,
You can restrict select-options.
SELECT-OPTIONS : S_VKORG FOR TVKO-VKORG MEMORY ID VKO.
Form F1000_RESTRICT_VKORG.
INITIALIZATION.
PERFORM F1000_RESTRICT_VKORG.
Define the object to be passed to the RESTRICTION parameter
DATA lw_restrict TYPE SSCR_RESTRICT.
Auxiliary objects for filling RESTRICT
DATA lw_opt_list TYPE sscr_opt_list.
DATA lw_***      TYPE sscr_***.
Assign selection screen objects to option list and sign
NOINTERVLS: BT and NB not allowed
CLEAR lw_opt_list.
MOVE 'NOINTERVLS' TO lw_opt_list-name.
MOVE 'X' TO: lw_opt_list-options-cp,
               lw_opt_list-options-eq,
               lw_opt_list-options-ge,
               lw_opt_list-options-gt,
               lw_opt_list-options-le,
               lw_opt_list-options-lt,
               lw_opt_list-options-ne,
               lw_opt_list-options-np.
APPEND lw_opt_list TO lw_restrict-opt_list_tab.
KIND = 'S':
CLEAR lw_***.
MOVE: 'S'          TO lw_***-kind,
         'S_VKORG'    TO lw_***-name,
         'I'          TO lw_***-sg_main,
         '*'          TO lw_***-sg_addy,
         'NOINTERVLS' TO lw_***-op_main.
APPEND lw_*** TO lw_restrict-***_tab.
CALL FUNCTION 'SELECT_OPTIONS_RESTRICT'
       EXPORTING
            restriction            = lw_restrict
       EXCEPTIONS
            too_late               = 1
            repeated               = 2
            selopt_without_options = 3
            selopt_without_signs   = 4
            invalid_sign           = 5
            empty_option_list      = 6
            invalid_kind           = 7
            repeated_kind_a        = 8
            OTHERS                 = 9.
IF sy-subrc <> 0.     "Restriction error encountered for Select
                         "Option
    MESSAGE I001 WITH 'ERROR IN SELECT OPTION'."ERROR IN SELECT OPTION
ENDIF.
endform.                    " F1000_RESTRICT_VKORG

Restrictions for Unencrypted VLANs in 1200

Similar Messages

Maybe you are looking for