Revert back to single click commands?

While using my iPhone 4 the system behavior changed where I now have to click on the app to select it, then double click to launch it. Same goes for entering in my password to access the phone and entering digits to make a phone. I am also having trouble swiping the screen to move to the next page. This is no longer working. I did not change any settings, the phone just started behaving this way. Any ideas on how to revert back to the single click selection/launch? Any assistant is greatly appreciated. Thank you!

The config will be saved as config.old when you change the mode of the firewall (this goes both ways I believe). As Luis has mentioned it is a major change but if you have ASA's in a failover pair then doing this with little or no down time should be possible.
I would first go about this by taking the current Standby ASA and take a backup of the running configuration on it, and make any required changes to the configuration to suite your needs. Most likely you will not have much need of what is in the system context, but take a backup of it anyway just be on the safe side. Then change it to single mode with the command "mode single". Now copy the configuration into the ASA.
Now, assuming that both ASAs have the same IP addresses assigned to its interfaces, remove the currently active ASA and then connect the ASA that is now in single mode back into the network. You may have to clear the MAC address table on some servers depending on how old they are and how touchy they are.
Do the same for the second ASA and connect it back to the network. Now, if you have kept the failover configuration, the ASAs will setup an Active/Standby failover in single mode and replicate the configuration.
Your down time should only be dependent on how fast you can remove the second ASA and add the first ASA back to the network.
Please remember to rate and select a correct answer

Similar Messages

Cisco ASA5520 multiple context revert back to single context

Hi all,
We have a redudant set of Cisco ASA5520's. This firewalls runs in multiple context mode.
No we want to make both "virtual" firewalls physical.
We already migrated on of the two firewalls to another physical set.
Now we would like to revert back the multiple context into single context mode, with keeping on of the two firewalls as the new running config.
We would like to do this with a minimum downtime.
Is this possible, can someone advise?
Kind regards,
Danny van der Aa

The config will be saved as config.old when you change the mode of the firewall (this goes both ways I believe). As Luis has mentioned it is a major change but if you have ASA's in a failover pair then doing this with little or no down time should be possible.
I would first go about this by taking the current Standby ASA and take a backup of the running configuration on it, and make any required changes to the configuration to suite your needs. Most likely you will not have much need of what is in the system context, but take a backup of it anyway just be on the safe side. Then change it to single mode with the command "mode single". Now copy the configuration into the ASA.
Now, assuming that both ASAs have the same IP addresses assigned to its interfaces, remove the currently active ASA and then connect the ASA that is now in single mode back into the network. You may have to clear the MAC address table on some servers depending on how old they are and how touchy they are.
Do the same for the second ASA and connect it back to the network. Now, if you have kept the failover configuration, the ASAs will setup an Active/Standby failover in single mode and replicate the configuration.
Your down time should only be dependent on how fast you can remove the second ASA and add the first ASA back to the network.
Please remember to rate and select a correct answer

How can I open all the tabs saved in a sub folder of the bookmark menu simultaneously in a single click/command ?

I have saved some of the related tabs in a common sub folder in the bookmarks list and whenever i have to open this tabs always i have to open them individually coz the 'open all in new tabs' option is not available for subfolder, so is there any command or click available from which i can directly open all the saved tabs of a subfolder simultaneously in one single attempt ? using vaio laptop, windows 7 basic, firefox version 6.0.2 !

yes i do that on my desktop but i dont have middle click option on laptop and even in the right click context the ''open all in tabs'' option is desplayed but is in light color i.e. not functional. Is this a problem with windows 7 or missing plugin or add on could help or extension of some sort ? please help !

L10: Using single click for extended desktop

Hi
I use a Sattelite L10 for presentations. Is there a way to set up the extended desktop with a single click (one! via .exe, .reg , .. file etc)? (A hot key would be nice too)
The problem is, if I start the computer without the external monitor / projector etc connected it reverts back to single display (normal desktop) and I have to Click right, browse to the correct option etc) I want a single button on my desktop / taskbar. (or hotkey)
Thanks
JP

Thanks for the replies.
But it obnly works until you shut down and restart without the external monitor attatched!
Thene you have to right click, properties, choose extended desktop etc again.

For some reason, I now have to double-click on my bookmarks on my task bar. How do I change it back to a single click?

In my bookmarks task bar, I used to have to just single click on the bookmark and it would open to that site. Now it seems that I have to double-click to get the bookmark to open. I want it back like it was - single click opens site. Please tell me how to fix this.
Thank you!

hello, can you try to replicate this behaviour when you launch firefox in safe mode once? if not, maybe an addon is interfering here...
[[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]]

I've just found the keyboard shortcut in Garageband for 'copy region' had changed from cmdC to ctrlC. I went to Preferences and clicked Restore Defaults for shortcuts. Now its altC . How can I get it back to the original commands.

I've just found the keyboard shortcut in Garageband for 'copy region' had changed from cmdC to ctrlC. I went to Preferences and clicked Restore Defaults for shortcuts. Now its altC . How can I get it back to the original commands.

When I use find file http://www.macupdate.com/app/mac/30073/find-file (which does tend to find files that "Finder" can't), it's not coming up with any other itunes library files that have been modified in the past week, which I know it would have been - unfortunately, I don't have a very recent backup of the hard drive. It would be a few months old so it wouldn't have the complete library on it....any ideas? I'm wondering if restarting the computer might help but have been afraid to do so in case it would make it harder to recover anything...I was looking at this thread https://discussions.apple.com/thread/4211589?start=0&tstart=0 in the hopes that it might have a helpful suggestion but it's definitely a different scenario.

How can I revert back to version 5.1 from 6.1. Bluetooth support told me that version 6.1 is not supported. I highly doubt it. My voice recognition reconizes " Call my wife command".

I just bought a new car. Hyundia Hybrid. My bluetooth is not Reconizing my command to call a contact. I've been back to the dealer and no luck. When speaking to Bluetooth support directly he doesn't see Version 6.1. and suggested going back to Version 5.1 which is documented to be compatable with my Iphone 4s.
I doubt it because voice recognition takes the command " Call Wife" Can I revert back to 5.1 without clearing my phone back to origional settings?

I'm sorry, but Apple does not provide a downgrade path for iOS. Because downgrading is unsupported by Apple we cannot discuss it on these forums, but you can use Google to find information on how to install an older version of iOS on any iDevice.

The stills in my movie project do not respond when I try to edit their "duration" I change it the clip inspector and click done, but when I exit clip inspector , it reverts back to what it was prior to my trying to change it?

The stills in my i movie project will not allow me to edit the duration time. I change it in the clip inspector, but when I click done, it just reverts back to what it was prior to my attempt to change it?

Hi There,
I tried your workflow and some how I am not able to see your issue.
- Will it be possible for you to share your project(where-in you always see this issue) with us. You can upload your project and send the link to maanand (at the rate of ) adobe (dot) com.
- If sharing of project isn' t possible then please share the project details such as no of slides, objects etc.
-Manish
blogs.adobe.com/captivate

My iPhone 4S has decide to stop playing any of my music. All my songs are there, but when I click to play, it just scrolls through a bunch of songs and then reverts back to the play list. Anyone have any suggestions as to how to correct this? Thanks.

My iPhone 4S has decide to stop playing any of my music. All my songs are there, but when I click to play, it just scrolls through a bunch of songs and then reverts back to the play list. Anyone have any suggestions as to how to correct this? Thanks.

I am having the same issue. And today, I noticed that when I was talking on the phone, the volume went down low. I had to reboot the phone, so that the volume was up again. Mostly, though, it's my music that I am having issues with.
Same issue as listed above. iPhone 4S. IOS6.

Open with & Change All revert back to Preview. Can't set Photoshop instead.

To help with analysis of this issue, my system is a G4 PowerMac running OS X Tiger 10.4.11. This issue also involves Photoshop 6.0.1 running in Classic mode.
For my Photoshop files, the default application is no longer set as Photoshop, but instead as Preview. I would like to reset Photoshop as the default application for all files ending with the ".psd" extension. When I right-click (or control-click) on a file ending in a ".psd" extension, select "Get Info", then under "Open with" choose Photoshop, and finally click the "Change All" button, the "Open with" setting reverts back to Preview. I am able to change one file at a time, by selecting Photoshop under "Open with" and by then avoiding clicking on "Change All". Regrettably, it is not feasible to change the settings for every single ".psd" file on the computer in this one-by-one manner.
Does anyone know how to change the default application globally for all ".psd" files to Photoshop, using the command line? I have searched for information on the Internet about the "defaults" command line utility, but have been unable to find an answer in that regard.
Does anyone know of an alternative means by which to resolve this issue?
Thank you for your time and help.
-John

Thank you for the suggestion, BDAqua. Regrettably, the problem continues to persist. The command at that link did indeed do something because the choices for "Open with" were different. Also, after running the command, Photoshop was not among the default choices, although it could be found after clicking on "Other". This might be shedding light on something. The copy of Photoshop is on a secondary hard drive in order to save space on the main hard drive. Maybe if Photoshop is on the main drive and then the command from the linked page is run, that might solve the issue.
After the opportunity to test that, I plan to post a follow-up message. I must confess that it might be a few days before that happens.
Thank you again for you help, BDAqua.
-John

My Adobe Creative Suite 6 (I guess student edition) expired HELP! Can I revert back to CS5??

Can I revert back to CS5?? (I have a comic deadline to make.)
I know 5 is registered here on the site. It was a digital copy. I looked at my old laptop. (3 years old or so.) and noticed 5 on there. I can still use it. Some how my CS6 just up and quit working. Which I thought was funny considering I bought it the same way I bought my CS5. I am working on two comic series of my own that are going to be published as E-books and physical books and need some advice.
I am left without Illustrator to use and I was right in the middle of working on all my character concept art to get trademarked.
( I can't afford the 357 upgrade to "re-open:" CS6 so I am left without anything to work on. All of my Illustrator files are also JPEG so i can view them all, but I was in the middle of new artwork when my CS6 decided to become a trial and I got locked out once the "Trial Period" ended.
I am a legally blind Cartoonist and Comic Artist and these series are my first real big projects that are getting published. I really don't want to have this process stopped for any longer than it has been. It's been almost a month since I was able to draw. (I can draw on paper, but with my eyesight Adobe Creative suite is perfect for me and causes less strain on my eyes.) It's my preferred platform to work on as far as drawing.
Hope somebody can help.
(I just got married so I am low on funds at the moment. This project is my baby and I do not want to leave it unattended to for so long.)

STEP 1:
FOUND MY PROBLEM (or half of it.)
I went into my computer and then program files.
I found that EVERY SINGLE TIME I click any of the Adobe Applications that say (64 Bit) they give me that error message I showed you in an above post.
STEP 2:
I clicked Adobe in program files.
STEP 3:
I can SUCCESSFULLY open any of my Adobe Apps that are not (64 bit)
It turns out all of my desktop shortcuts of my adobe apps were all coincidentally 64 bit ones that don't work.
SO- in conclusion I think I have partly solved my problem.
I replaced all of my app shortcuts with the normal program files and NOT the 64 bit ones. BUT- I am worried....aren't the 64 bit versions of ANY apps you buy important?
I do feel worried since my WINDOWS 7 PROFESSIONAL is a 64 bit OS. This would effect my programs correct?
Feel free to use my story to help you solve other customers' stories. I would like my problem looked into, but I am only half as stressed now.

In IPhoto I have edited the order of my images. When I play the album on Apple TV the order reverts back to the time stamp. Any suggestions on how to get the images to play on my TV in the order I want?

Apple TV won't play back my album images from IPhoto in the edited order I want. The order seems to revert back to the time stamp for the photos. I have combined the photos from 3 different cameras and they had slightly different clock settings. I am working on an edited presentation of about 1500 Pics from travels in Turkey this summer and sometimes the order makes more sense if I move some of the images quite a ways. Is there any solution short of changing the time stamp on every single image?

Using the 'adjust date and time' setting is the best way to syncronise the photos from all your cameras. However as you say this merely puts them all in the correct order chronologically.
If there are photos that you feel would be best somewhere else in an album other than in date order, it may depend on how many as to which is the best option for you. If it's only a few you may wish to adjust the date/time on these few manually so they fit in with the rest where you want them.
If you have a lot of photos you want in a different order to the order by date, or you really don't care about what date/time is used and just want them in the order you want them in, then 'batch change' is the best option.
From the view menu, select 'sort photos - manually', drag the photos around until they are in the order you want, select all of them. Now select the batch change option and choose 'Date' from the 'set' options, type in a date and time for the first photo, it can be anything but it's probably a good idea to choose something close to the original date, then check the box 'Add'. You can keep the value set at 1 minute or enter any value you want, it may be more realistic to divide the length of your holiday by the number of photos you have to calculate a value, but it really isn't necessary. Clicking OK will adjust all the dates without affecting the title or description and the photos will now show on the Apple TV in that order.
Just to be sure iTunes is updated, you may want to go to the advanced menu/choose photos to share in iTunes and deselect the album, apply, reselect the album and apply again.

Numbers 3.2 has changed too much, it doesn't work with my project anymore. How do I revert back to the previous version I was using?

Numbers 3.2 has changed too much, it doesn't work with my project anymore. 1) The sheet panels used to be on the left hand side and easily reviewable and searchable, but now they are on the top and it's harder to find a specific folder without scrolling (too time consuming), 2) I used to be able to duplicate a folder within my sheet panel window by simply clicking on a folder and hitting Command D, but that doesn't work now so it looks like I'll have to spend even more time to recreate the same tables that used to be easily duplicated, and 3) I can't choose fill colors that matched my project anymore because there are only limited choices available now. And these are only the changes that I'm aware of. I am very disappointed and frustrated. Whatever the motivation was to limit Numbers 3.2, I want the previous version back. How do I revert back to the previous version I was using?

The sheet panels used to be on the left hand side and easily reviewable and searchable, but now they are on the top and it's harder to find a specific folder without scrolling (too time consuming),
You can scroll more quickly between sheets if you don't use the left-right triangles, but instead move the cursor up into the bands with the "tabs" and drag right or left.
Also, if you have a lot if sheets for which you want a quick vertical list, then you can try the following have something like this pop up (showing your sheet names automatically) whenever you hit a keyboard shortcut (in my case shift-command-j):
This is done via a Jump to Sheet Automator Service (Dropbox download). To install just doubleclick the .workflow package and (if needed) click 'Download Anyway' in System Preferences > Privacy & Security.
This will cause a new item to appear in your Numbers > Services menu. Then, if you want a keyboard shortcut, go here in System Preferences and add one:
You can rename or remove the service by holding down the option key in Finder and choosing Go > Library > Services. You can also view the AppleScript contaned within the service by opening the .workflow package in Automator.
This particular service jumps to the first cell of the first table of the sheet you choose from an automatically generated list of all sheets in the current document.
SG

My region keeps trying to revert back to the UK?

I am running Mac OS X Lion 10.7.5
I live in the US and bought this mac in the US but auto transferred from my UK PC. Now I cannot get the region or currency to remain in US dollars. I have been into System Preferences and changed the region to the US which automatically changes the currency to US dollars in the currency drop down menu. However as soon as I navigate away from SystemPreferences/Formats/Language&Text it reverts back to British Pounds.
I am trying to run a business in the US but my accounting software is using £ for all my invoices because it takes the currency from the system preferences.
Cheers, Matt

Problems such as yours are sometimes caused by files that should belong to you but are locked or have wrong permissions. This procedure will check for such files. It makes no changes and therefore will not, in itself, solve your problem.
First, empty the Trash.
Triple-click the line below to select it, then copy the selected text to the Clipboard (command-C):
find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 -o -acl $ 2> /dev/null | wc -l
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
The output of this command, on a line directly below what you entered, will be a number such as "41." Please post it in a reply.

Trying to change server to be a PDC; reverts back to Standalone Server

I'm trying to get my Leopard server to run as a PDC for windows authentication, but when I change the role from "Standalone Server" to "Primary Domain Controller" and click the save button, after authenticating with the "diradmin" account the changed settings all revert back to "Standalone Server" and nothing gets changed. Any clues as to what I need to do? The server is fully updated to 10.5.3, with all other software updates as well.

Hi Topher
I'm guessing you're referring to the post? Well the figure has gone up a fair bit since then. My overall total is quite high as I have been installing servers since 10.2.
FWIW my general rule of thumb is:
1 Format drive, install server
2 On Restart Server Assistant launches (see linked post) don't start any services using Server Assistant
3 Server Assistant does start VNC and enables SSH and the Root Account
Depending on your view SSH and Root are potentially a security problem, deal with these later on.
4 Server Assistant writes settings and preps the server for first use
5 Don't launch WGM or Server Admin. If Server Admin launches, quit it
6 Manually download the latest OS update, don't use Software Update
7 Install this and on successful restart run Software Update again and install the rest of the updates
8 Make sure server is fully up to date before launching Server Admin
9 User server's .local name to log in initially
10 Enable and Configure DNS Service first
I can't stress this enough but if you devote time and energy on this before doing anything else it can prevent a lot of hassle and problems later on. DNS does not have to be running on the Server itself. If you have another server for example you can configure DNS Services on that. You could even use 3rd-Party DNS Software and install on a client machine for example. An old Graphite G4 with DNS Enabler installed is good enough. There are PC equivalents you could use as well. This approach does not require anything in terms of processing power, large drives or even vast amounts of RAM. Reliability and correct configuration is the key.
11 Test and Qualify the DNS Service before moving onto anything else.
Once you are happy enable AFP and SMB. Create a test user in the local node and see if you can access the default share points from a client. Try it with both protocols. Don't be tempted to delete the default share points either. You'll have serious problems if you do.
12 Enable the Open Directory Service
13 Promote to Open Directory Master
If DNS is perfect the Kerberos Realm and search base fields should autofill themselves with information based on the domain name defined in the DNS Service. For example an FQDN of myserver.mydomain.com would result in MYSERVER.MYDOMAIN.COM for the Kerberos Realm and dc=myserver,dc=mydomain,dc=com for the Search Base. I always use the default diradmin name rather than any other. You should not use the local administrator account name
Launch Directory Utility and verify the loopback address (127.0.0.1) is entered as a new configuration. Access Server Admin's File Sharing window and enable the Users folder to automount for home directories. Quit out of Server Admin and launch WorkGroup Manager
Try and get into the habit of only having one or other of the Server Applications open at any one time on the server itself. Its OK to have both open if you are administering the Server remotely if you install them on a client
Authenticate to the /LDAPv3/127.0.0.1 node and you should see Directory Administrator UID 1000 already waiting for you. Create a user and select Advanced. You should see the afp url for the default Users folder. Click create home now and Save. Navigate to the Users folder and you should see a home folder created for that user, inspect the contents of this folder and you should see the usual home folder folders. Quit out of WorkGroup Manager
Launch Server Admin select SMB and go for promotion. Supply diradmin as the user name and its password and you should have the server acting as a Primary Domain Controller
Everything can be achieved using the GUI. There should be no need to resort to the command line although if you want to - as you well know - you can
As for your question? No I have not seen any problems with the 10.5.3 update. The 10.5.2 update has given me a problem on a handful of occasions. The problem was traced - eventually - to failing hard drives.
I apologize for the long post but who knows you might find it useful?
Tony

Revert back to single click commands?

Similar Messages

Maybe you are looking for