Revert from DD-WRT to Linksys WRT54G v5.1 firmware

I'm using DD-WRT v24-sp2 build 12548M on my Linksys WRT54G v5.1.
Where can I get the Linksys original firmware (v5.1) and how can I install it?

I don't think there's still an available firmware for any version of the WRT54G. This is a really old Linksys model and I'm not sure if there's a firwmare available anywhere else.

Similar Messages

Why does the Linksys WRT54G router REQUIRE a hostname when it's never used?

Why does the Linksys WRT54G REQUIRE a hostname when it's never used?
I can't find a single use for the router hostname, yet the Linksys WRT54G version 5 firmware v1.00.6 wireless router REQUIRES a hostname, even though nothing actually uses that hostname.
Why does the router require a hostname (why can't we just leave that field blank)?

Date: Sun, 8 Jul 2007
To: [email protected]
From: "Debbie Hurley"
Subject: "Unnecessary Router Name Requirement" bug in WRT54G V5
This is to report a bug in the "Setup", "Basic Setup"
tab, "Router Name" field
(https://10.2.18.20/basic.htm) in the otherwise
wonderful Linksys WRT54G V5 wireless router (firmware
revision 1.02.0).
As you are aware, a router is a security and privacy
device; as such, it should not require identifying
information if that identifying information is not
needed nor used by the user or their ISP.
Such is the case with the "router name" field.
In the case of the "Unnecessary Router Name
Requirement" bug, I am reporting to you (and to the
associated Linksys forums at forums.linksys.com) the
Router Name field should NOT be required. It should be
an option to leave the Router Name field blank.
The fact that the router name field MUST exist
(whether or not it is actually used or desired), is an
obvious security and privacy flaw in the otherwise
wonderful Linksys WRT54G router. Please fix this bug.
Thank you very much,
D. Hurley
(Mod note: Post has been edited for non-compliance of forum guidelines.)
Message Edited by primus on 07-08-2007 11:13 PM
Message Edited by primus on 07-08-2007 11:14 PM

AirPort Express drop-out / skips -- Windows XPSP2 w/ Linksys WRT54GS router

Hello,
I'm having some skipping / drop-out issues when streaming music from a Windows XPSP2 fileserver, which runs iTunes 7.3.2.6, to my AirPort Express. I've long suspected my LinkSys WRT54GS router. Here are some things I've tried:
* tried enabling logging on my AirPort Express unit, (I actually installed a Windows SysLog client and ensured it was working) but it reveals no useful information after a skip -- just debug logging. No change.
* changed the wireless channel from 6 to 11. No change.
* Do not have wireless security enabled (just don't broadcast ESS ID). No change.
* Latest firmware on router, AirPort Express, and iTunes. No change.
* All other wireless devices in the house turned off. No change.
I'm seriously considering buying a new wireless DSL router to see if it makes the problem go away (any suggestions to makes or models appreciated). Unfortunately my WRT54GS is not one of the routers that supports reflashing with a third-party firmware, or I would have done this eons ago.
Another thing I am not sure how to test is the signal strength that the Airport Express gets from my LinkSys WRT54GS router. I've not been able to figure out how to get this information, and I also do not know what are considered good / not-good strengths. Any help here would be great.
Here are some details.
AirPort Express with Firmware 6.3, communicating wirelessly over Channel 11 to my LinkSys WRT54GS router with firmware 1.52.0, into which my Windows XPSP2 fileserver is physically connected with CAT5 cable. The music files are served up on a Maxtor DiamondMax 10 7200 rpm 300GB Serial ATA-150 Hard Drive.
I've really tried everything I can think of, and I still get skipping.
Specifically, music will play fine for 45 minutes, or 5 minutes, or an hour; then, the music will suddenly stop. The AirPort Express will continue to have its green LED on, though. The music will resume 1-10 seconds later. This skipping will happen periodically for a 1-2 minute period, usually 2-3 times per minute, go away for an indeterminate amount of time; or, it might persist until I get tired and turn off my stereo. There is no pattern as to time of day so I don't suspect neighborly interference.
Other things in the house are an older 802.11b laptop, 5.8GHz phone, brand new microwave, and a few dozen Palm and Windows PDAs that all have their WiFis disabled, where appropriate.
Any suggestions or ideas would be fantastic. This has been a problem for a couple of years now which I have systematically (though unsuccessfully) tried to solve.
Thanks,
-Jeff

I haven't yet budgeted to buy a different router, but I'll respond when I do as to whether this was the fix or not.
Just an observation ... in your case, the music streams wirelessly from your laptop to your router, and then wirelessly again from the router to your Airport. That's 2 wireless paths it must go. In my case, music streams directly to my router with a LAN cable; then, wirelessly from my router to the airport. So that's only 1 wireless path, and even still I am experiencing problems.

Need Help Streaming Video From Web Server Built Into Application - Linksys WRT54g Router

Very much appreciate any help getting streaming video feed from web server built into video application to work properly using port forwarding on my Linksys WRT54g wireless router.
Here is the situation:
My PC is connected to the internet via a Linksys WRT54g wireless router.
The Windows XP Pro SP2 firewall is enabled, with a firewall exception established for the video camera application.
On the router, forwarding of port 80 is enabled for the LAN IP address of the PC running the video application with an embedded web server, and the web server in the video camera application is also set to use port 80.
I have a free DYNDNS account and also run the DYNDNS updater program on the PC running the video application with embedded web server. According to the DYNDNS web site and the DYNDNS updater program, the IP address assigned to the machine running the video application with embedded web server is set correctly in my dyndns account.
When I open a browser (Explorer or Firefox) on the PC running the video camera application with embedded web server, I am able to connect to the video application's web server by going to the dyndns address linked to the machine running the video application. The video application's web server is set to use the dyndns address. That's the good news. The bad news is that I can't connect to the video application's web server from any machine that connects to the internet that uses a router other than the router used by the PC running the video application. I am only able to connect to the streaming video from the application's web server only on machines that connect to the internet using the same (home) router used by the PC that is running the video application.
Since I am able to connect to the video app's embedded web server successfully on the machine running the video application, it seems that at least something about the current port forwarding settings is correct. For example, if I uncheck 'enable' for forwarding of port 80 on the router settings page, I am no longer able to connect to the video app's web server when I try to do so in a browser running on the machine running the video app. When I re-enable port 80 forwarding on the router, I am again able to connect to the web server of the video application on the machine running the video app. I thought that by enabling forwarding of port 80 on the router and associating that port with the LAN IP of the machine running the video application, it would be possible to connect to the streaming video of the video app's embedded web server from ANY machine connected to the internet, but that is not the case. There must be some other router settings to update/change in order to get the port forwarding working to enable a successful connection to the video web server, but I am stumped. Very grateful for any suggestions as to how to get this working properly.
Thanks in advance...

The firewall log can be configured on the third tab in the window for the firewall settings, where you can turn the firewall on and off completely.
From your tests, though, it does not seem to be the firewall. However, to be sure, it would be good to check the log. It will help to eliminate the firewall as the culprit and you may find it handy in the future, too. ;-) Just don't forget to turn the log off again after you are done because it may cause some performance penalty on your system while on.
From what you write, it seems as if I should give a little networking background on the ip addresses you'll see. Your setup is (or should be) a modem connected to the WAN/Internet port of the WRT. The computer is connected into a LAN port of the WRT.
Your router has two IP addresses (that's what makes it a router): a WAN address and a LAN address. The WAN address is the address assigned by the ISP. It is a normal internet IP address. Everyone is able to send packets to this IP address. The WAN address is the one reported by whatismyipaddress.com, it should be listed in the dyndns record and it is the address that your router shows on the Status page. It's the public IP address of your router. Dyndns maps your dyndns.org name to that IP address.
Your router also has an IP address on the LAN side. You can configure it to be whatever you want. The default is 192.168.1.1 with netmask 255.255.255.0 and it is better to leave it like that or at least inside the network 192.168.*.*. 192.168 is a special, reserved IP address range for private networks. Basically, routers in the internet are not supposed to forward addresses in this range. That makes them suitable for private LANs as the packets never can get anywhere. Most people using Linksys routers have there LAN in 192.168.1.*.
The router acts as gateway, which means it forwards packets from PCs in the LAN to the internet and back. As all your PCs in your LAN share a single WAN IP address, the gateway does address translation (NAT). This works only in one direction: from the inside to the outside. The router remembers when a PC in your LAN sends something out and accepts the responses in and sending them back to the PC. If something comes in from the internet which cannot be associated with a ongoing communication the packet is dropped unless you use port forwarding.
All computers in your LAN either have a static IP address assigned or use DHCP to get it automatically. The router has a DHCP server as well which gives out IP address from 192.168.1.100-149 if not changed. With a router with default settings static IP addresses can be in the range of 192.168.1.2-99 and 150-254.
ipconfig /all reports your IP address in your LAN, i.e. an address 192.168.1.*. The gateway in this output should be 192.168.1.1 which is your router. And packet no in the LAN address range 192.168.1.* is send to the router which forwards the packets into the internet.
An address 192.168.1.* should not appear as internet address in the Status page of the router nor should it appear at dyndns.
Port forwarding is used to operate a server in the LAN. By default, a server in the LAN cannot be reached from the internet. You have to configure port forwarding for this. You configure that traffic bound for a specific port (e.g. TCP port 80 for http) on your WAN IP address is forwarded to the same port on a specific LAN IP address. If your server runs on 192.168.1.50 than traffic to your WAN IP address port 80 is forwarded to 192.168.1.50 port 80. That way your HTTP server can be reached from the internet. As you can only configure a fixed IP address in port forwarding it is recommended that the server uses a static IP address and not DHCP as in the latter case the IP address may change over time...
O.K. so much for networking. I hope that makes things a little clearer and you can verify that your setup is how it is intended to be.
I suggest the following: on the router's security page there is an option to block WAN requests. Remove the check if it is set (meaning: do not block). After you did that change you should be able to ping your WAN address (e.g. ping xxxx.dyndns.org) from the internet. That way we know that it is on the correct address.
Also on the Administration page make sure that remote management is disabled (should be like that per default) or that the management port is NOT 80 but for example 8080. What is your your UPnP settings on the same page?
O.K. that should be enough for the moment...

MacBook Pro can't obtain IP address from Linksys WRT54G v2 router

I believe I am having the issue described in the article below:
http://docs.info.apple.com/article.html?artnum=304817
In a nutshell, AirPort seems to be seeing the wireless router just fine, but internet connect is a no go. The router is a Linksys WRT54G v2, which should - SHOULD - work w/ my brand new MBP C2D 17", based on the reports I have seen in other threads here.
In the Network Status tab of the network pref pane, the message is: "Airport is connected to the network linksys. Airport has a self-assigned IP address and may not be able to connect to the Internet." This is in line with the Apple tech doc cited at the link above.
I am starting a new thread on this because, unlike many of the other folks who are having problems connecting wirelessly, my actual wireless connection seems to be rock solid (AirPort connects to the Linksys instantly, and shows up as full strength with no apparent dropouts). The problem seems to be with the IP address, as the MBP can't/won't pickup anything other than its self assigned IP when connecting.
Here are the things I have tried so far (most of which are probably irrelevant as it turns out, b/c the actual wireless connection has been fine - just not the TCP/IP stuff):
1. Updated to latest firmware in router.
2. Tried switching to different wireless channel (ch. 11 in this case, based on reports in other threads).
3. In Linksys settings, changed beacon interval to 50 and lowered packet thresholds as described in another post (can't find the link right now).
4. Formatted and re-installed OSX onto the MBP. Did NOT use Migration Assistant this time (since others were apparently having problems due to out of date prefs and PowerPC related items copied over from older machines).
5. Updated to latest version of OSX Tiger (10.4.8 with all patches installed) using a wired Ethernet connection to the internet.
6. Downloaded and installed the AirPort Update patch 2006-002 located at:
http://www.apple.com/support/downloads/airportupdate2006002.html
7. Repeatedly trashed all AirPort-related keychain items and the SystemPreferences folder in Root/Library/Preferences.
8. Repeatedly trashed and re-created a new wireless location using Network Assistant.
9. Salaam thrice towards Cupertino, wave rubber chicken and bathe self in pigs' blood while humming a continuous medley of Mac startup chimes from the last two decades.
Just kidding about #9, mostly.
I am starting a new thread about this because I believe my issue is OS related. The AirPort hardware seems to have a a full-strength and non-intermittent connection to the Linksys router. The problem appears to be w/ the (in)ability of OSX to negotiate an IP lease with the Linksys box.
I am posting this to the Linksys forum as well, but do not believe this to be a Linksys issue. I have two other PowerPC-based Mac laptops in my office, both of which connect flawlessly to the Linksys. (I'm typing this from one of them.) In fact, I have torture tested my new MBP with several other wireless routers with the same result - MBP will not connect, while both of the PowerBooks work like a charm with the other routers in question. Therefore, it surely seems to me like the common denominator here is definitely the MBP and not the router. I realize that in the support doc at the top of this post, Apple claims it is the responsibility of the router manufacturer, but I just cannot buy that line - based on the fact that EVERY OTHER LAPTOP that I own works great with the Linksys except for my shiny new MBP.
Beautiful machine otherwise and I really can't wait to get it working, but this is a SERIOUS pain in the you know what.
At any rate, if anyone has any ideas as to what to try next, I would love to hear about it. I will be calling AppleCare again first thing tomorrow morning, but it always seems the users are better informed than the Apple guys.
Thanks in advance for any suggestions.

if other computers connect to the router just fine , doesn't seem to me a router problem then .. the only thing i can think is to try connecting to a different network and see whether it does any good to u...can't help much if it's an OS related issue...

Use airport express to extend network from linksys wrt54g

Hello all, I'm having no luck here, and hope you can help me. I am running a MacBook Pro, 2.16 GHz, Intel Core 2 Duo, 3 Gigs ram, OS X 10.6.8.I am at work, trying to use a newly purchased AirPort Express to extend the signal from the back office, which has a Linksys WRT54G router. I updated the router's firmware to 1.02.8, build 001, dated 8.5.09. I have tried numerous times to configure the AE using AirPort Utility, and always wind up with an error message, "An error occurred while updating the configuration. Make sure your Apple Wi-Fi base station is plugged in and in range of your computer or connected via Ethernet and try again. (-6753)" During the configuration process, I am asked what I want to do with AE, I have tried both "create a new wireless network," and "I want AE to join my current network," with no success. Any comments will be appreciated.

The Linksys WRT54G and WRT54GS (through version 4 only for both models) were said to be compatible with Apple's WDS settings.
Perhaps this article may offer some clues, but it is doubtful that you will be able to make this work with the particular version of Linksys router that you have.
http://hints.macworld.com/article.php?story=2006060516541633

Help protect my Linksys WRT54G from the "curl" command which bypasses my security settings

It's way too easy to break into my Linksys WRT54G router!
Do you have firmware that will fix this vulnerability?
Instantly bypassing the administrator password, my fifteen-year old
neighbor broke into my Linksys WRT54G router (firmware revision v1.0.0.6)
in ten seconds simply by sending this one "curl" command to it via the
Internet from his home next door!
c:\> curl -d "SecurityMode=0&layout=en" http://192.168.0.1/Security.tri
This kid was kind enough to knock on my door today to tell me to fix it.
I invited him in, and from inside my own house, he showed me the Linksys
WRT54G command above which immediately disabled all my wireless security
WITHOUT him having to enter any password!
He showed me how to disable remote administration but he said the
vulnerability still exists until I get a new router. I can't believe
everyone with a Linksys WRT54G router is throwing it in the garbage.
Where/how can I find a firmware update that protects me from this curl
vulnerability?

To protect your router:
* disable remote management.
* enable WPA2 or WPA with a strong preshared key on the router.
That is essentially all you must do. This protects against the curl problem (from the outside). The benefits of the rest varies:
* set a strong, hard to guess password on the router.
That's always a good idea to prevent some guest coming over, plugging into your network and modifying the router. For that to be relevant the person either needs physical access to your wired LAN or the WPA key.
* disable UPnP
Good idea if you are worried you could install some malware on your computer. UPnP allows to set port forwardings for incoming connections from the internet. It allows a computer to automatically setup the forwarding to make a server accessible in the internet. You'll often need this for gaming. But it obviously can be exploited by malware.
* access server to https instead of http
With WPA in place on the wireless this is only really necessary if you worry about someone gaining physical access to your router. https protects the password transmission to the router. But then, if someone gains physical access to my router I think the protection of my password would be the least of my problems.
* disable wireless access to the router configuration
For this to be effective with WPA in place would require the attacker to crack WPA to get into your WLAN. WPA is considered secure at this time. Anyone cracking WPA with a strong key must have a lot of computing power and a lot of knowledge. I don't know if this setting would really prevent that attacker of gaining full access to the router. This setting may be useful if you have an occasional guest to which you grant wireless access to the internet...
* changing the default IP address from 192.168.1.1 to something else and turning off the DHCP server on the router
With the DHCP server in place changing the IP address is no mean of protection because the DHCP server assigns a correct IP address in your LAN. You have to setup static IP addresses on all computers and devices. However, if someone gained access to your LAN (wireless or wired) all you have to do is wait and listen to the LAN traffic. It usually takes a few seconds until some noisy windows computer will broadcast a message and you have picked up the IP addresses in the LAN
Some more things often mentioned with questionable benefits:
* turn off SSID broadcast
Supposed to make the WLAN "invisible". O.K. It does make it harder for the average Joe to check what WLANs are in the neighborhood and which channels they use to optimize the choice of channels and limit interference. It does also prevent accidental connection attempts. However, with WPA/WPA2 in place the WLAN is protected anyway. Anyone, who really wants to know if there is a network can scan with a wireless card in monitor mode. The SSID is transmitted unencrypted. Plus in average it requires more times and more power (on laptops) to connect to the network as the wireless card must actively try to connect to each configured WLAN on the computer to find out if the network is there or not. With SSID broadcast it simply scans for broadcasts and then knows the network is there...
* wireless MAC address filtering
Supposed to limit the computers which can connect to the WLAN. Only computers with the MAC address on the list can connect. Again, this only prevents accidental connection attempts. MAC addresses are transmitted unencrypted. It is easy to pick them up with a wireless scanner. Thus, for anyone who knew how to crack WPA the MAC address filter list will be the least of problems. Most wireless cards can be configured with any MAC address you like. But the list increases the amount of effort for you to add another wireless computer to your WLAN as you always have to remember to set it up correctly...

Why did the setting for my Linksys WRT54G router change spontaneously from encrypted to open mode?

I unplugged power to my Linksys WRT54G (802.11g) router for about six days. It had been set for WEP 128-bit encryption. When I replugged it, it identified itself as an open (non-encrypted) network. I could use it by setting up a new network connection (unencrypted) on my PC, but could not access it using the original (encrypted) PC network connection.
After reinstalling the router, and setting it for WEP 128-bit encryption, it works fine again.
Can anyone explain why the router spontaneously went from encrypted to non-encrypted mode, as a result of being powered down for several days? (Is this a bug or a feature?

Thank you. As noted, I reconfigured it & it works fine again. But do you have any idea why it "lost" its encryption setting by being powered-down?
In particular, is this likely to happen in future if I power-down Linksys?

Macbook Pro/linksys wrt54g slow wireless/wired network connection solution.

I was pulling my hair out looking for a solution for this and it did not seem anyone had too much luck here. Hopefully this will help you all...
Setup:
- Macbook Pro, Mac mini, 2 windows boxes (not mine), 1 linux box
- Linksys WRT54G v6 with dd-wrt installed. This solution should work with the standard WRT54G firmware.
Symtoms:
- All other computers performed fast on internet speed tests and on network transfers.
- Macbook Pro Internet connection was slow (40KB/s on both the wired and wireless network using wpa)
- Macbook Pro internal connection was slow (2MB/s on both the wired and wireless network using wpa)
Things I tried to resolve this:
- Disable IP v6 (no effect)
- Set DNS Servers field to the dns servers as reported by the router. (Increased the initial speed but this quickly decreased making it useless... not to mention impractical)
Thing that resolved my issue.
- Disabled STP (Spanning Tree Protocol) on the router. In the DD-WRT it is towards the top of the Setup tab. I'm not sure where it is on the default firmware sorry.
Hope this helps someone
Mac mini 1.42 Ghz Mac OS X (10.4.7)

Steve Caplin wrote:
Darin,
You're right - there are a lot of issues about MBP WiFi. I think there's a major problem with it.
If there was a ..."major problem with it" you would see more complaints than wifi just being among the top 10 discussion items in a trouble shooting forum. There are millions of MBP users many of whom, like myself, use wifi every day without issue.
Your statement "They exchanged it for a new machine. Worked fine in the store - but when I got it home, I was still getting very slow speeds." would lead one to suspect maybe interference from some source or a configuration issue rather than a "major problem".
You probably already tried changing the channel, resetting your router, changing the security scheme, elimination possible sources of interference, separating your components (router, computer, external monitor, ...), etc. but maybe starting over with a default configuration will help isolate the problem.

How to hook up a Linksys WRT54G to Motorola NVG589. PLEASE HELP!

Hello, I have recently switched over to AT&T Uverse and I am loving it. One thing I miss is having extra ethernet ports to plug in my desktop computer and my Xbox 360. When the Uverse technician came in, he installed a Motorola NVG589 modem that also has a built in wireless router. He also installed a VAP2500 as a receiver for 2 wireless TV boxes. The VAP2500 plugs into the back of the Motorola NVG589. 3 other TV boxes are plugged into the back as well. My dilemma is the fact that all of the ports are being taken up. I need at least 2 more ethernet ports free so I can hook up my Xbox 360 (my model doesn't have built in wifi) and my desktop computer as well. I told the technician this when he installed the system and he told me to go on ebay and buy 2 cheap splitters and split 2 TV boxes that are coming into the NVG589. I did so. It didn't work out. I called up AT&T and the guy over the phone said that was the worst thing I could've done. He told be I should buy an ethernet switch. I had my Linksys WRT54G (Version 6) router laying around at the time and realized that it had a built in ethernet switch. I want to get this to also function as another Wifi hotspot because I have an old PowerMac G4 downstairs that won't connect to the NVG589 for some reason (it says connection timeout). I am guessing that the wifi card in the system may be too old to connect to the modern NVG589. So, I need the 2 extra ethernet ports and another Wifi hotspot from this setup. I have tried multiple things to get this to work. The closest way I could get it to work was when I plugged an ethernet cable from the LAN port on the WRT54G to port on the back of the NVG589. I then plugged the TV box ethernet cable I had to disconnect into the second LAN port on the WRT54G as well as plugging my Xbox 360 into the 3rd LAN port and my computer into the 4th LAN port. This worked great for the TV box and the Xbox 360. However, the computer's ethernet connection ran very slow and the WIfi from the WRT54G was very slow as well. The Wifi from the NVG589 was slow too. I unhooked that setup and put it back to what it was beforehand. Is there anyone that knows of a flawless way of setting this up? Any articles someone can link me to? I've heard of bridging the NVG589...would that help me? How exactly would I do that? Please HELP. I have attached pics. On the back of the NVG589 - green ethernet is the DSL cable, both white ethernet cables along with the black one are TV boxes and the yellow ethernet cable is the VAP 2500. Thanks!

craigarc303 wrote:
Hello, I have recently switched over to AT&T Uverse and I am loving it. One thing I miss is having extra ethernet ports to plug in my desktop computer and my Xbox 360. When the Uverse technician came in, he installed a Motorola NVG589 modem that also has a built in wireless router. He also installed a VAP2500 as a receiver for 2 wireless TV boxes. The VAP2500 plugs into the back of the Motorola NVG589. 3 other TV boxes are plugged into the back as well. My dilemma is the fact that all of the ports are being taken up. I need at least 2 more ethernet ports free so I can hook up my Xbox 360 (my model doesn't have built in wifi) and my desktop computer as well. I told the technician this when he installed the system and he told me to go on ebay and buy 2 cheap splitters and split 2 TV boxes that are coming into the NVG589. I did so. It didn't work out. I called up AT&T and the guy over the phone said that was the worst thing I could've done. He told be I should buy an ethernet switch. I had my Linksys WRT54G (Version 6) router laying around at the time and realized that it had a built in ethernet switch. I want to get this to also function as another Wifi hotspot because I have an old PowerMac G4 downstairs that won't connect to the NVG589 for some reason (it says connection timeout). I am guessing that the wifi card in the system may be too old to connect to the modern NVG589. So, I need the 2 extra ethernet ports and another Wifi hotspot from this setup. I have tried multiple things to get this to work. The closest way I could get it to work was when I plugged an ethernet cable from the LAN port on the WRT54G to port on the back of the NVG589. I then plugged the TV box ethernet cable I had to disconnect into the second LAN port on the WRT54G as well as plugging my Xbox 360 into the 3rd LAN port and my computer into the 4th LAN port. This worked great for the TV box and the Xbox 360. However, the computer's ethernet connection ran very slow and the WIfi from the WRT54G was very slow as well. The Wifi from the NVG589 was slow too. I unhooked that setup and put it back to what it was beforehand. Is there anyone that knows of a flawless way of setting this up? Any articles someone can link me to? I've heard of bridging the NVG589...would that help me? How exactly would I do that? Please HELP. I have attached pics. On the back of the NVG589 - green ethernet is the DSL cable, both white ethernet cables along with the black one are TV boxes and the yellow ethernet cable is the VAP 2500. Thanks! Ya, the install tech must have been sleeping or texting or something during training.... or it's possible he misunderstood you and thought your were talking about needing extra phone ports, which could be accomplished with simple splitters. You were almost where you needed to be with your setup, you just missed some steps. Connect your wired computer only to one of the Linksys' LAN port. With the Linksys powered up press and hold the reset button for 15 seconds (will need toothpick or unfolded paperclip). This will perform a "factory" reset. When the Linksys is fully rebooted, log in to the Linksys. Do not configure the "Internet Connection Type" on the Linksys. Navigate to the "Wireless" section on the Linksys and configure the wireless. Do not use the same SSID (wireless network name) that the NVG589 uses. Save changes. Navigate to the "LAN" configuration on the Linksys and set the routers address to 192.168.1.1 and disable the DHCP Server. Save changes. This step will kick you out of the router. Power down your computer and the Linksys, run an Ethernet cable from a LAN port on the NVG589 to a LAN port on the Linksys, then power up the Linksys, and when it's fully rebooted, power up your computer. You should be good to go at this point. You will want to individually configure your wireless devices to use either the wireless network from the NVG or the wireless network from the Linksys. Otherwise they make keep jumping back and forth between the two, which will degrade performance for that device. You may still notice a slight to moderate performance drop for the wireless on both the NVG and the Linksys because they will be competing for the same wireless airspace along with the VAP2500.
How can you be in two places at once, when your not anywhere at all?
I really want to become a procrastinator, but I keep putting it off.
There are three kinds of people, those that can count, and those that can't.
“Our great democracies still tend to think that a stupid man is more likely to be honest than a clever man, and our politicians take advantage of this prejudice by pretending to be even more stupid than nature has made them." :Bertrand Russell

Insufficient Bandwidth Linksys WRT54G 2.2

IChat 3.01 works fine if I connect my computer directly to my Comcast cable modem. When connected through the WRT54G I can text chat but audio chat attempts produce the dreaded "insufficient bandwidth" message. I updated the Linksys to v4.20.7. I have tried to open ports as listed in some of the other posts on this problem. I have selected Upnp enable, and Upnp disable. I have selected DHCP disable, and enable. I have reinstalled the 10.4.2 update. I have repaired permissions. In short, I have tried to utilize every fix detailed in the hundreds of messages offering fixes. Since iChat works fine without the Linksys in the mix, I am inevitably led back to the idea that somewhere I have a mistake in my Linksys setup. Has anyone got a setup guide for v4.20.7 firmware of the Linksys WRT54G that will help me step through each and every setting required to get this thing working? Or is this device just not going to ever work with iChat? Thanks in advance for your help.

I have the WRT54G (Ver 4.0/4.20.7 firmware). I have mine configured with UPnP only which opens the following ports: 1024 to 5000 Both TCP and UDP.
Try configuring it only with UPnP enabled(Take out all of the port forwarding and port openings, Unplug your modem, router, and mac and then plug them in in this order: Modem (then wait a minutes or two),router (then wait a few seconds), and then your mac and give that a go.
Then try testing with a known working screen account. (My screen name is in my profile if you want to test with me)
I've noticed the WRT54G isn't real good releasing ports from UPnP without rebooting.
That's how I got my WRT54G working and I can now chat with both Mac and PC's.
Hope this helps!
P.S. I have my mac firewall off.

Hi, I just bought a linksys WRT54G Wireless Router. My...

Hi,
I just bought a linksys WRT54G Wireless Router. My laptop was able to detect it wirelessly untill I changing the "Router Name" in the setup page(http://192.168.1.1)
While saving the settings, the wireless network suddently disconnected. From that point onwards, I was not able to detect the wireless network with any computer at all.
I tried unplugging it, resetting it, and even restory factory settings by holding the reset button for aprox 30 secs.
What is wrong?
Thanks in Advanced

Recheck the wireless setting (SSID, encryption, DHCP, etc) on router management page again. Also make sure your computer's wireless adapter setting matches the one you set on router.
picoHat
Home Network, Wireless Network and Computer Networking Made Easy

Linksys WRT54G Wireless-G Router Not working

I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

Linksys WRT54GS Version 6 router help

Hi all! I have a Linksys WRT54GS Version 6 router with Firmware Version: v1.50.6 and I was wondering if anyone could help me find a free log viewer, since the log viewer that comes with the router just gives the last few sites outgoing and incoming, and it doesn't time it either. Anything that will work with my router that will record all day info as well as put the time? I'd also like it (if possible) if it could identify which websites those IP's belong to; sometimes I will put an IP in the address bar and nothing happens or I get an error.
Also, I can't seem to be able to telnet into my router. I put the right IP 192.168.1.1 8080 which is the port that shows under Administration/Management "management port:" 8080. When I telnet (I'm using vista and I installed the telnet client and server) it says connecting and then just sits there for a long time and then asks me to push any key and says connection timed out. I also tried with port 80 and 23, nothing.
Thanks!

*BUMP*
I gathered from what I read on the 'net that this particular router pretty much sucks in terms of putting 3rd party firmware, of telnetting into it, etc. So, is it basically true that there is no way to telnet into this? Also, no one knows of any monitoring or log viewer that works with this version?? Please?
Message Edited by PsychGirl on 04-16-2009 09:35 AM

Using Linksys WRT54G as an AP

I recently moved into a new home with a roomate and our DSL box is 4 port wireless router. One desktop is hardlined into that, my laptop has no problems keeping a good connection to it wireless, but my PC in the back bedroom frequently drops connection... and I'm getting really tired of /release and /renew. I have a Linksys WRT54G v6 wireless router and was wondering if there is someway I can use this product to boost my signal to the DSL box. I'm kind of computer savvy but this is stumping me. I hardlined the DSL box into the Linksys from one lan port to the other (not the uplink) and it seemed to be working ok except for the PC that's hardlined into the DSL box. The other two wireless comps were working fine. Any advice would be greatly appreciated... I really just want to boost the signal a little bit so I have a steady connection. Thanks in advance,

My PC is on the other side of the house as the router, the laptop in the middle room, and the router and other PC is in a room with the router. The channel on both routers is 11 because I've encountered problems with phones before. Its definitely a signal issue because I always connect with low signal strength and frequent drops. The Linksys has a stronger antenna than the DSL box does which is why I'm wanting to use it as an AP, even if I have to hardline it into the DSL box. Thanks for the reply.

Revert from DD-WRT to Linksys WRT54G v5.1 firmware

Similar Messages

Maybe you are looking for