RF change destination bin

Experts,
I am trying to change the destination bin in RF putaway LM02 transaction.
I hit the F7 NBin go to Change destination screen where i am asked to verify the bin and enter the modified dest bin.When its says verify the bin, should i scan the new bin or scan the old bin ? If scan the new bin in the verify bin field(triggers 'enter' upon scanning) , it takes me back to the previous destination screen with no change of the bin.
If I scan the new bin in the modified dest bin directly , which again takes me back to the destination screen with no change.
What are the actaul steps to perform without having the user manually enter the new bin ?
Thanks for time in advance
Edited by: RKsap193 on Mar 23, 2010 2:51 PM

I tested this practically.Please follow below process
1.Scan the new bin in field ""Verify bin"where you want to do putaway of material .
2.After scan you have to say F7 check. It will automatically display new bin in Modified dest bin field.
3.Say F1 confirm. By this system will bring you to "Destination Information -Single item " screen where you will find the destination bin is changed in destination bin field.
By this in TO display you will see new scannned bin with the putaway & confirmation.
Regards,
Prashant

Similar Messages

Cannot change destination bin during confirmation

Dear SAP experts,
We are in SAP ECC 5.0. We read that we can change the destination bin during confirmation of TO. We have done the pre-requisite:
1. In relevant storage type (001) we input '1' for dst bin ch during confrm field
2. Untick physical inventory during placement to bin
Then we do GR to PO, which generate TR. We create TR into TO and specifying bin INTERIM in storage type 001. During confirmation in tcode LT12, I cannot change the destination bin. What else do I miss in here?
Best regards,
John

Hello John,
Even though config mentions change of destination bin, there are quite a few limitations.
Have a look at below documentation from SAP
http://help.sap.com/saphelp_47x200/helpdata/en/c6/f83e5a4afa11d182b90000e829fbfe/frameset.htm
Snapshot of some imp content.
No destination bin can be entered during confirmation for
dynamic coordinates
transfer orders with return subitems
Lean WM (if the destination bin is defined in the movement type)
posting change TOs
inventory based on putaway
additions to existing stock in storage units
stock removal from or putaway into bulk storage
two-step confirmation
transaction Confirm single item
the case where you are using a putaway strategy
all other items in a TO with storage units, if you have already confirmed the first item for the storage unit. The system changes the destination storage bin for all dependent items during confirmation of the first item.
stock removals from a bulk storage managed with storage units
Check if your putaway falls in any of the criteria.
Cheers,
Nag

Destination Bin change in Pick Module Replenishment scenario

Dear Experts,
We have a requirement to perform destination bin change during TO confirmation into the pick module for replenishment scenario. The requirements is as below:
System set up:
We have a storage type 001 (Replen Storage type) that has been configured with putaway strategy as 'F'. It is basically a pick module wherein we have defined one fixed bin for every SKU or Material in WM2 view and we have defined the minimum, maximum, control quantity & replenishment quantity.
Our requirement is to perform a two step confirmation for the stocks going into this pick module meaning although the fixed bin in determined during TO creation user needs flexibility to change the destination bin to a new interim bin during confirmation and then they will intern perform a bin to bin transfer from interim bin into the actual fixed bin location.
We do not want to activate standard 2 step procedure as it will impact other kind of picking process. Hence need a solution to perform destination bin change as below.
1. For Material A and Fixed Bin 001 in storage type 001, the stock level has gone below minimum quantity.
2. A transfer order is created automatically to replenish this bin from another storage type(This is standard SAP replen process).
3. The user will pick stock from the source storage type and deposit the stock into an replenishment interim bin which is also a part of the same pick module.
4. The user wants to confirm stock in interim by changing destination bin to say bin 002 in storage type 001. Although we have activated destination bin change for this storage type it is not allowing us to change bin during confirmation.
We are looking for help from experts to provide a solution for this scenario. Is activating destination bin change for fixed allowed by standard SAP? If not what are the other alternatives to achieve this functionality. Please refer the attached document for details.
Best Regards,
Harish

Hi Harish
How is the replenishment triggered..are you using LP21,LP22 or LP24...IF YOU use any of these standard SAP TCode, first the system creates TR and the bin gets fixed in the TR itself. Even by having destination bin changeable at the time of confirmation will have no effect and will continue to remain grey.
I had a similar requirement in one of the projects.Placement strategy was next empty bin and since fixed bin was maintained in material master , system was always defaulting fixed bin in TR. When TR was converted to TO, the same bin got carried over
to avoid this we used user exit EXIT_RLLNACH4_004 to prevent defaulting of bin in TR. TR was created without destination bin. When TR is converted to TO, system can find the bin based on the strategy maintained. This works very well and we have used it successfully
Regards
Jayaram

Change of bin not possible during TO confirmation

Hi all.
I am trying to change the destination storage bin during transfer between bins (WM movement 309).
The strategy is fix bin (maintained in material master), so the TO is created with fix destination bin and operator must change it before confirmation.
For example, in GR it is possible to change destination bin during confirmation in transaction LT12 but not for transfer. The receiving storage type is the same in both cases. Is there any customizing missing?
Apart from this, is there any way to confirm items separately inside a TO? For example, during GR I try to confirm a TO in transaction LT11 for just one item and waiting for the rest to be placed physically in order to confirm all the TO but destination bin can not be modified in LT11. Is there any way to confirm item per item but allowing changing destination bin? it is possible to do it in LT12 but not in LT11.
Many thanks in advanced and best regards.

Hi,
Generally, it is possible to change the destination bin during TO confirmation. However, this is not possible under the following conditions:
o With dynamic coordinates
o If the destination bin location is specified in the movement type
o For posting change transfer orders
o For the physical inventory using a putaway
o For the addition to existing stock for storage units
o For the transaction Confirm Single Item (transaction LT11)
o If a bulk storage type is involved in the stock movement
o In the event of an individual putaway strategy
o If the first item of a TO with storage units is already confirmed
   since all the other items of the storage unit relate to the same
   storage bin. When you save the first TO item, the system changes
   the destination storage bin for all dependent items.
o If this is a replenishment transfer requirement for a fixed
   storage bin.
Please see SAP Note number 443916 for an explanation.
Thank you.
Patrick

WM: Change source bin confirm transfer order

Hi guys,
Do you know if I can change source bin when confirming the transfer order.
I know I can customize the system if I want to change destination bin when confirming the transfer order.
Thanks,
Fatih.

Hi,
Hope you cannot change the source bin but as per the configuration in the picking strategy in the customizing you can define the picking sequence for the souce bins.
example: like check bin " A" if ......(condition)...then pick from bin " B " or pick from bin " C".
Regards,
Ravindran

Change Storage Bin Number in 309 movement type

Hi Gurus,
I have problems with creation TO for movement type 309(material to material posting), when i want to create the TO for that movement type, i can't change the destination bin.. The destination bin field in that TO is disable, how to make that field enable?
I try to add an user exit after creation of that TO, the user exit is MWMTO001.. so the user exit used for change the storage bin number after the TO created.. but that user exit never triggered after TO created.. How it could happen?
Any suggestion, how to change the storage bin number when i want to create TO from 309 movement type(material to material posting)?
Kind Regards
Ken

Hi Kris,
Ya, i already create the bin number, for example i material A fixed to bin 00001 and material B fixed to bin 00002, when i do movement 309 from material A to material B, why the bin goes to 00001? why not goes to bin 00002? Because material B is fix to bin number 00002..
For your solution, i just can change the bin during confirmation of the TO? Because, in this case, confirmation of that TO done by external system, so the external system will send idoc to SAP to confirm that TO..
Regards
Ken

RF screen : how to change the bin using LM63...

Hello,
We use LM63 to create transfer orders (TO) from the shipment.
In some case, we need to change the bin wich is proposed by the system.
Is there any solution to change a bin or cancel the TO and create it again using a new bin ? We need to do it from the Radio frequency screen.
thank's for your help and your contribution...
Mathieu and Hughues..

Hi...
In the configuration of the storage type there should be a flag that allows the change of the destination storage bin (within a single storage type).
This bin field should then be changeable in the transfer order confirmation screen and LM63
However, this changeable bin is not supported as standard if you use handling units
Regards
Steve

Change of Bin while confirming TO (Picking strategy FIFO)

Dear WM experts,
We use FIFO strategy for picking. Now for an outbound delivery we have the requirement to generate TO automatically. During confirming of the TO we should have option to change the suggested Bin (in the source storage type).
Could you please confirm what settings in IMG should I take care of for achieving this.
Thanks a ton.
Kamal

Hi,
I'm afraid it isn't possible...
You can set destination storage bin change for your storage type in SPRO:
Logistics Execution ® Warehouse Management ® Master Data ® Define Storage Type
You can find a field called 'Dst bin ch. during confirm'...BUT SAP help says:
'No destination bin can be entered during confirmation for
- dynamic coordinates
- return items
- Lean WM (if the destination bin is defined in the movement type)
- posting change TOs
- inventory based on putaway
- additions to existing stock in storage units
- transaction Confirm single item'
I guess you are using dynamic bins for outbound deliveries...
http://help.sap.com/saphelp_46c/helpdata/en/c6/f83e5a4afa11d182b90000e829fbfe/frameset.htm
Just my opinion...
BR
Csaba
Edited by: Csaba Szommer on Jun 3, 2008 8:38 AM
Edited by: Csaba Szommer on Jun 3, 2008 8:38 AM

Changing source bin

Hi,
I want to change source bin once the transfer order is already created is it possible? and how? as far as I know it is not possible, but I want to know if some has done something similiar and how was it? And if you gave a RF solution
Thx
Edited by: Mariana Hernandez on Jun 23, 2009 5:15 AM

Hello,
I do not think we can change the source bin but we can change the destination bin in case of RF solution.Also I guess it is possible to change the destination bin without RF solution. The destination bin can be changed by maintaining indicator in storage type master data for "Dst bin ch.during confirm".
Regards,
Prashant

Change destination storage during putaway

Folks,
I would need to be able to change the destination storage bin during putaway. I;ve set the indicator in the storage type, however, I am not able to change the destination bin. Any suggestions?
Thx,
MdZ

Hi Csaba,
it was exactly what I read when I have this problem:
"No destination bin can be entered during confirmation for
dynamic coordinates
transfer orders with return subitems
Lean WM (if the destination bin is defined in the movement type)
posting change TOs
inventory based on putaway
additions to existing stock in storage units
stock removal from or putaway into bulk storage
two-step confirmation
transaction Confirm single item
the case where you are using a putaway strategy
all other items in a TO with storage units, if you have already confirmed the first item for the storage unit. The system changes the destination storage bin for all dependent items during confirmation of the first item.
stock removals from a bulk storage managed with storage units"
As I wrote Continuous inventory upon placement into stock indicator must be unchecked.
Andrzej

How to change destination drive? From C to D?

How to change destination drive? From C to D?
Not enough disk space on drive C
Solved!
Go to Solution.

Which device and destination for what ? Is it for the Nokia Store downloads ? If 'Yes'.. Go to Nokia Store in your phone and Log-in ..Then go to Options --> Account --> Settings --> Installation Preferences .. and select the appropriate destination..

How to change destination table dynamically in configuration file in ssis?

hello,
i have a package i am having one data flow task.in data flow task i have one source and one destination.source and destination are different.i have created xml configuration file by configuring source and destination connection
strings.
now i want to change destination in the same server to different database with out opening the package.i want to directly change in the config file.we can change it by modifying configured value proerty and intial catalogue value.but if the table is not
existed in the changed database.how we can create it dynamically.

HI jiri Neoral,
thanks for reply,as you said above process by this we can do change only databasename.if in my destination database,the table which i used in package is not existed,can we create it dynamically
using config file.later changing table name is possible?
For that you need to have a step in SSIS package prior to data flow task to check if table exists and if not create it
You can use execute sql task with query like below
IF OBJECT_ID('TableName') IS NULL
CREATE TABLE TableName
Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

Putaway Strategy for replenishment of fixed bins - SU destination bin

My client is using ECC 6.0 Retail and using WM.
After creating the TR for the replenishment of the fixed bins according to the bin situtation using LP21, we create TOs using LB11 for article. At the TO creation, the system creates a new Quant and automatically proposes the SU# from the source bin to the destination bin. We allow addition to stock but not mixed SUs. However you can manually overwrite and input the current SU destination bin but this is very time consuming. Is there a way to have this process done automatically?
Thanks Gaetan

Hi Gaetan,
It seems this topic is extremly important recently...e.g.:
Addition to storage unit
I'm not aware of anything in standard SAP that would help you to realize your scenario. (if it is very important maybe it should be indicated to SAP AG. However, in a WH where SU management is active the material flow is realized trough SUs > if warehouse workers add the stock physically from one SU to other SU it means additional work for them physically and therefore in SAP too).
Regards,
Csaba

Dynamic destination bin with Mov. Type 311-312 and Storage type 001?

Hello WM experts,
I'm tryng to determine dynamic destination bin with mov. type 311, when trasfering handling units from IM to WM storages (VLMOVE). First 311 transfer to St. type 921, and then 312 transfer from 921 to St. type 001. I don´t want to use a Fixed destination storage bin in St.type 001, I'd like to configure this like movement type 601, that create a dynamic destination bin using outbound delivery. Can be this possible?
Another question I have: Is possible to crearte individivual items with Source target quantity in alternate unit equivalent to 1 unit, in LT03. For example, the item 10 of my outbound delivery says 3 ST of XYZ material. But I want to crear 3 items with Source target qty. 1 ST. Is this possible with customizing or using an enhancement? ...
Why I want to find a way to do any of these things above, because when I have indivial intes in the TO, I can confirm them in RF (LM61) just pressing one button, I don't need to declare any difference, and makes my picking process faster.
Best regads, and thanks for you time and help.
Favio Del Castillo.

Hi Mohit ,
please check below link , you need to perform steps as given
http://help.sap.com/saphelp_470/helpdata/en/4d/2b90b043ad11d189410000e829fbbd/content.htm
also see the sales order subcontracting using the business addon
http://help.sap.com/erp2005_ehp_04/helpdata/en/c7/2587b8dad94c52854ccd28015dceb0/frameset.htm

Changing the Destination bin for Outbound Delivery

Hi All,
For any Outbound delivery, when we do TR and TO by default the goods gets posted to 916 interim shipping area. Now if I want to change this interim bin to a different area. What checks and changes I need to do?
thanks for help,
G

Hello,
(1) Go to OLML>activity>transfer--> movement type configuration. Look for 601 movement type of your WH number.
Remove the storage type 916 and enter the storage type of your choice. Enter the Bin number of your choice.Remove dynamic selection flag
(2) Create LS01N with storage type and bin which you have entered in step 1
Thanks
Milind

RF change destination bin

Similar Messages

Maybe you are looking for