RF Grouping not showing

I have configured 2 controllers with the same RF Group name in the CONTROLLERS-->GENERAL page. However, when I go to WIRELESS-->802.11A or B/G and look at RF Grouping I only see the indivdual controller I am on in the grouping. I do not see the other controller. Each controller feels it is the group leader as well.
I have verified these controllers can ping one another and they both are up in the same mobility group so they can communicate.
I am running code version 6.0.182.0.
Any config steps I am missing here? I followed the config guide to the letter, which basically said to jsut add the group name, and I have double checked the RF Group Name is identical on each controller.
One caveat, I have no AP's joined yet, to either. Not sure if that in some way would be required. If not, can anyone lend any insight on what I might check in the configs or logs to see what is going on here?

The absence of AP may explain your result. If no AP reports to any of the controllers, the controllers do not have APs belonging to the same RF space, and therefore have no reason to communicate with each other. This would be my first guess.
As for the process itself, you are right: controllers should belong to the same mobility group, and know each other (so each controller MAC and IP is entered into the other controller under Mobility group).
Also keep in mind that RRM information use UDP 12124/12134 for 82.11b/g and UDP 12125/12135 for 82.11a, these ports need to be open between controllers.
Hope it helps
Jerome

Similar Messages

Address Book Groups not showing up in iTunes

The groups that I have set up in Address Book are not showing up in the Info tab in iTunes when attempting to sync my iPhone. The iCal calendars show and sync with no problems. I have tried resetting sync history, logging off of my .Mac account and logging back in.
Any advise? Thanks.

Don't take what I have to say as fact, because I don't use a Mac and could be mistaken. I remember reading last night something about people taking and checking the box on the Summary page of iTunes to replace the info on the iPhone with the computer. Once that was done, it seemed to correct this issue and showed the address groups after that.
It might be worth the experiment, however I would make sure I had a backup of the phone before I tried it. I know it was only the last day or show that I read it, so if you want to search the forum before you try it, be my guest. I don't want to ruin anything for you, but I just remember reading that someone did that and it fixed it.
Hope this helps.

Groups not showing up in contacts?

Hi! My groups are not showing up in my contacts in the Address Book. Any idea why, or how I can make them show up? Thanks.

If all contact info is available online with your MM account - when checking your MM address book via webmail access using a browser, try turning Contacts off for over the air syncing with your MM account on your iPhone. This will erase all contact info on your iPhone. Follow this by turning Contacts back on for all contact info available online with your MM account to be re-downloaded to your iPhone's address book.
When you say you did a complete reset with your iPhone, does this mean you restored your iPhone with Tunes from your iPhone's backup?

Public logon group not showing up

Hi everybody
I am trying to create a SAPGui entry for logon group access to customer ECC6.0 system.
I have configured the service and sapmsg.ini file.
I was told by customer sysadmin that PUBLIC logon group was created but in the list of logon groups I can only see SPACE.
Moreover, if I complete the procedure with SPACE logon group, when I try to login it won't succeed, warning that even the client number is wrong (?!).
My questions are:
- how to retrieve message server number and port (even though I am fairly certain that they are ok, otherwise the Logon group list wouldn't have been populated... right?)
- what might be the cause for the PUBLIC logon group not to show up
Thanks, points will be awarded
Vincenzo

Hi,
Since you get such strange errors, it almost seems like you are trying to logon to the wrong server.
Please check sapmsg.ini again to see that the correct hostname/ip-address is entered.
Also, did you notice if the server name is correct at the logon screen ?
Every Dialog instance or Central Instance gets logon group SPACE by default. Then, when you create logon groups for the instance,
the group SPACE will disappear.
In some installations the central instance and the message server both uses the instance number of the central instance as a base to calculate the ports.
CentralInstance/DialogInstance = 3200, MsgServer=3600
but, on some installations (E g Windows Cluster) this could be different.
There you might have something like:
CentralInstance/DialogInstance = 3200 and the MsgServer=3601
You need to ask your sysadmin for message server port and host.

Update account group not showing in fs00

HI, previously i have created 1 account group i.e. (current asset& liabilities group) without any posting i devided that into two group i e current asset , current liabilities. but problem is its not showing separately on drilldown of account group of gl master record.
pls can u clarify me .

Hi,
Pls. check that newly divided account groups' From and To account range. It should not overlap with the older one.
Also check in t-code FSP0 to see if 2 account groups appear.
Regards,
SRidevi

Custom Groups not showing in Reports

Hello,
Per our reporting requirement, I have created few groups in Authoring pane. However, when I am going to select those groups in reporting, its not showing up.
Env: SCOM 2012 R2.
Any help is appreciated.
Thanks,
Binoy Das

Hi,
It seems like that there is a sync issue/latency between the operational database and the data warehouse in your case. Groups should appear in the data warehouse within just a minute or two in most environments. Check errors and performance on
your management servers and sql servers.
Do you see any error or warning Events in the OperationsManager Windows Event log on one of the management servers which could be related to db issues?
Regards,
Yan Li
Regards, Yan Li

Contact Groups not showing up on Iphone when syncing with Mobileme

My contacts show up in my address book on my Iphone but when I go to look at my groups the page is blank and I cannot get back to my contacts without closing and reopening contacts but still no groups. I want my groups to show up. I have at least 4 groups that show up on my me, and syncs fine with ipad....
I THINK THIS IS A ISSUE with the new verizon iphone.
Please help if anyone has

I am having a similar issue. As is my wife. I also believe that it is a bug in the current iOS on the CDMA iPhone 4.
It is just as you described, and I have to close Contacts completely in order to restore my access to the contacts list. And, like you, our groups show up just fine on our iPads (within minutes of making changes, as we sync over MobileMe).
It doesn't appear to be a letter-case issue, as at least my login is in all lowercase letters.
I sure hope that this is fixed in an iOS update soon! It's rather problematic for those of use who use their iPhones for business purposes.

ADF Data Visualizations group not showing up in Component Palette

I apologize for my ignorance, but I cannot find how to solve this problem. I am trying to use the data visualization components such as graphs but my component palette does not show this. It does show ADF Faces, JSF, and some others, but not this. I tried adding more libraries to my project's properties, but it does not show up. I am using:
JDeveloper
Studio Edition Version 11.1.1.2.0
Build JDEVADF_11.1.1.2.0_GENERIC_091029.2229.5536
Any ideas?
thanks,
Kerry

Go into project properties -> JSP libraries and make sure you add the data visualization tag library.

HT201077 Photo stream group not showing up

I was invited to a photo stream and I clicked join, but when the link takes me to my photo streams that stream does not show up no matter how long I wait

Wow! Ive always just gone straight into photos from camera! Really appreciate that......

Members of Domain Local Groups not showing up through net group command

Hello,
I am trying to get the list of members in a Domain Local Group using "NET GROUP" command, but unable to get the member list.
I get the message "group not found", whereas members of Global Groups are visible.
Thank you in advance !

Unfortunately your post is off topic here, in the TechNet Site Feedback forum, because it is not Feedback about the TechNet Website or Subscription.
This is only one forum among the many that are on the TechNet Discussion Forums, and given your post, you likely chose the wrong forum.
This is a standard response I’ve written up in advance to help many people (thousands, really.) who post their question in this forum in error, but please don’t ignore it.
The links I share below I’ve collected to help you get right where you need to go with your issue.
For technical issues with Microsoft products that you would run into as an
end user of those products, one great source of info and help is
http://answers.microsoft.com, which has sections for Windows, Hotmail, Office, IE, and other products. Office related forums
are also here: http://office.microsoft.com/en-us/support/contact-us-FX103894077.aspx
For Technical issues with Microsoft products that you might have as an
IT professional (like technical installation issues, or other IT issues), you should head to the TechNet Discussion forums at
http://social.technet.microsoft.com/forums/en-us, and search for your product name.
For issues with products you might have as a Developer (like how to talk to APIs, what version of software do what, or other developer issues), you should head to the
MSDN discussion forums at http://social.msdn.microsoft.com/forums/en-us, and search for your product or issue.
If you’re asking a question particularly about one of the Microsoft Dynamics products, a great place to start is here:
http://community.dynamics.com/
If you really think your issue is related to the subscription or the TechNet Website, and I screwed up, I apologize!
Please repost your question to the discussion forum and include much more detail about your problem, that could include screenshots of the issue (do not include subscription information or product keys in your screenshots!), and/or links to the problem
you’re seeing.
If you really had no idea where to post this question but you still posted it here, you still shouldn’t have because we have
a forum just for you! It’s called the Where is the forum for…? forum and it’s here:
http://social.msdn.microsoft.com/forums/en-us/whatforum/
Moving to off topic.
Thanks
MSDN and TechNet Subscriptions Support
Did Microsoft call you out of the blue about your computer?
No, they didn't.

Open Directory groups not showing up in Windows

Hello,
we are using Open Directory on a Leopard 10.2 as a primary PDC for mac, linux and windows clients.
The Kerberos sign in works as expected, but we can not get any group created in the OD to be displayed (or selectable) from windows. All users show up, but no groups.
Anyone got an ides or the same problem?
Message was edited by: majs

Same problem here. On Windows client we see only domain users, no domain groups.
No solution yet.

New chat groups not showing up in client

i have skype installed on my mac and, apparently, I was added to a few new converstations. I am not seeing any of the messages in my client though. No new group popped up in the left hand bar. Individual conversations are still working and old chat groups that I have work, but not these new ones for some reason.
I logged into Skype on my iphone and I see the new chats there, so this is only on my mac client.
I restarted skype on my mac, logged out, logged back in, and even uninstalled and reinstalled, but no luck. The new group chats still don't show up.
Any ideas?

Can you confirm you are using the latest Skype 6.18 for Mac from www.skype.com/go/download
You can check your installed version from the menu "Skype - About".
Please report back which Mac hardware you are using should you have problems updating to 6.18
If you are already using 6.18: Please share the first 5 lines of output from issuing the following chat command in any chat. Just send this like any normal chat message:
/dumpmsnp
Follow the latest Skype Community News
↓ Did my reply answer your question? Accept it as a solution to help others, Thanks. ↓

Groups not showing up in iPhone Sync Options

Runnning iOS 5 on an iPhone 4S (although I don't think that's the issue)
Running iTunes 10.5, Lion 10.7.2.
When syncing my phone via USB (or wireless for that matter) under the info tab the option exists to sync Address Book Contacts and there is a radio button that should allow me to select groups, however there are no groups to select and much of it is greyed out. I have 3 groups in my Address Book application, but they aren't showing up as options to sync to in iTunes.
I have restarted the computer in an effort to get iTunes to recognize (and offer) the Address Book groups to no avail.
Any suggestions?
Thanks.

Just as a follow up, I opened a support case with Apple on this topic because as stated my wife isn't/wasn't impressed with my Contact list. The fundamental problem is iCloud basically takes all the Contact Groups and moves them into the cloud which prevents you from selectively putting AB Groups on your phone from within iTunes. The resolutions was follows:
1. Close Address Book
2. System Preferences -> Uncheck Contacts (sync) (Note: Make sure you keep a copy on your Mac)
3. Wait an unspecified amount of time so that the contacts have time to sync up to the local Address Book.
4. Open Address Book (I don't believe that opening Address Book before your contacts sync matters) and verify that your contacts show up under 'On My Mac'
5. Reboot Mac
6. Open iTunes with your iPhone connected
7. Verify that you have a recent back up of your iPhone (iTunes Preferences -> Devices)
8. Goto 'Info' tab in iTunes under your iOS device
9. Check 'Sync Address Book Contacts' and leave it as 'All contacts'
10. Scroll to very bottom and check "Replace information on this iPhone' (assuming you don't want to Merge) Contacts sections
11. Click 'Sync' button
12. Once it completes the sync you should now have the option to sync only selected groups
I've added a feature (www.apple.com/feedback) to iCloud for the ability to sync iCloud AND to selected groups...or if they are so inclined the ability to sync selected groups with iCloud in general. This seems like a convoluted process to get this feature back but it works, I just wish Apple wouldn't change expected behavior for what I would think is a popular feature.
BivDog

Distribution group not showing up in Exchange 2007 GAL

Hello,
We have AD running on a 2003 R2 SP2 server
We have Exchange 2007 running on a 2003 R2 SP2 server on the same domain.
I put a distribution group (all staff) on the active directory server.    I can e-mail to [email protected] and it goes to everyone I put in that group no problem.   However if I do check name, allstaff isn't listed, I have to go to contacts and drop down to find that distribution group (under groups).   How do I get it into the global address list so it shows for anyone pressing alt K or checkname along with other members of our domain - I don't want them to have to drop down under the contacts item in outlook to go to groups to find it.
Thanks

Thanks - I don't think the regen of the address book is really the key but modifying the distribution group in AD after you create it in EMC.   I had regened the OAB a few times since last friday but the allstaff was only available under groups in outlook.   Maintenance runs every morning at 5AM and that didn't update the group into lookup in outlook.   It seems to be the broken AD interface between exchange 2007 and windows 2003.   You used to be able to see all exchange data for a user or group in AD however now part of it is in Exchange 2007 Management console and some is in AD users and computers.
THis is just one more item in my opinion along with the lack of gui control in exchange 2007 that displays the half baked creation that is Exchange 2007.   Is the next version of WIndows Server going to require all DOS commands like Exchange 2007 does to do any AD work?   Gussy it up with a fancy name like "POWERSHELL" but it is just another way of saying DOS to me.   Pretty sure PCs became more popular with GUI interfaces.    I used to be an MS FAN (not the same as fanboy who thinks they can do no wrong) but things at MS have taken a SERIOUS turn down hill as of late
Vista - incredibly bad performance - no such issue with WIndows 95, 98, 2000, XP - and then they claimed it was drivers, then it was third party apps such as AV or firewalls - 5 months later they finally admit as people set up boxes with all the extras turned off with identical hardware and the latest drivers - hmm XP blows the doors off vista for file copy performance - can't imagine why sales suck for business clients and Dell had to start selling XP again.
BTW - I tried their patch for performance - it actually decreased disk to disk performance on the same box while increasing performance by 20% in network copys however since network performance is up to 500% slower than XP that 20% increase doesn't really help enough to offset internal performance slow downs - here is a tip MS - strip out the DRM scanning and you'll get your performance back.
Exchange 2007 - ESM worked great in 2003, 2000.   2007 we bring you POWERSHELL known 20 years ago as DOS.   Much easier to write scripts like - ## AutoDisco for EWS
[array]$SCPCurrent = Get-ClientAccessServer
$autodiscoResponse = "<Autodiscover xmlns=`"http://schemas.microsoft.com/exchange/autodiscover/outlook/requestschema/2006`">"
`
+ " <Request>"`
+ " <EMailAddress>" + $siSIDToSearch.WindowsEmailAddress + "</EMailAddress>"`
+ " <AcceptableResponseSchema>http://schemas.microsoft.com/exchange/autodiscover/outlook/responseschema/2006a</AcceptableResponseSchema>"`
+ " </Request>"`
+ "</Autodiscover>"
$strRootURI = $SCPCurrent[0].AutoDiscoverServiceInternalUri.absoluteuri
$WDRequest = [System.Net.WebRequest]::Create($strRootURI)
$WDRequest.ContentType = "text/xml"
$WDRequest.Headers.Add("Translate", "F")
$WDRequest.Method = "Post"
$WDRequest.UseDefaultCredentials = $True
$bytes = [System.Text.Encoding]::UTF8.GetBytes($autodiscoResponse)
$WDRequest.ContentLength = $bytes.Length
$RequestStream = $WDRequest.GetRequestStream()
$RequestStream.Write($bytes, 0, $bytes.Length)
$RequestStream.Close()
$WDResponse = $WDRequest.GetResponse()
$ResponseStream = $WDResponse.GetResponseStream()
$ResponseXmlDoc = new-object System.Xml.XmlDocument
$ResponseXmlDoc.Load($ResponseStream)
$EWSNodes = @($ResponseXmlDoc.getElementsByTagName("ASUrl"))
if ($EWSNodes.length -ne 0){
$ewsURL = $EWSNodes[0].'#text'
than just clickin in Exchange System Manager and going to mailbox management like you had to in 2003.   Whew glad that trudgery is gone!   In just 20 lines I can do what I was forced to do in a couple of mouse clicks in the old version - happy days are finally here.
WM6 - the BT stack was horrible in PPC2003, WM5 it was still bad but we've made it intolerable in WM6 - and we've made sure you can't get in touch with anyone at MS to point out these issues.
Office 2007 - Gone are all those customizable menus that made your job easy - we've locked them down because we didn't have enough time to fix them after we scrapped our original ribbons interface - we tell you they are locked for security reasons but we'll bring it back as a new feature in the next version of Office.
Thanks for letting me dump on the *** coming from MS these days - if their surveys actually let you give open feedback it would be great but their surveys about products are more like -
Would you like to give feedback about VIsta?
Question 1 -
Do you think Vista is
a more colorful
b more intuitive
c more visually stimulating
Question 2
Do you think the menu bar
a Has better icons
b Has better fonts
c Looks more user friendly
A real question about my Vista experience would be
Question 1
What did you think was better about Vista
Question 2
What did you think needs fixing in Vista
Question 3
Any additional comments
MS is determined not to let in any info that might delay releases or improve their products.

SCOM Dynamic Group not Showing Health Watcher

I have the following code which shows a group of servers based on a registry key value. I am trying to add in the health watcher for heartbeat alerts. The computers show up in the group, but not the health watcher. What am I doing wrong?
      <Discovery ID="UINameSpace5f2cab25dac54b879a72830bf59d283a.Group.DiscoveryRule" Enabled="true" Target="UINameSpace5f2cab25dac54b879a72830bf59d283a.Group" ConfirmDelivery="false" Remotable="true"
Priority="Normal">
        <Category>Discovery</Category>
        <DiscoveryTypes>
          <DiscoveryRelationship TypeID="MicrosoftSystemCenterInstanceGroupLibrary7585010!Microsoft.SystemCenter.InstanceGroupContainsEntities" />
        </DiscoveryTypes>
        <DataSource ID="GroupPopulationDataSource" TypeID="SystemCenter!Microsoft.SystemCenter.GroupPopulator">
          <RuleId>$MPElement$</RuleId>
          <GroupInstanceId>$MPElement[Name="UINameSpace5f2cab25dac54b879a72830bf59d283a.Group"]$</GroupInstanceId>
          <MembershipRules>
            <MembershipRule>
              <MonitoringClass>$MPElement[Name="Type80531327bc2f439dba7c289399a2728e"]$</MonitoringClass>
              <RelationshipClass>$MPElement[Name="MicrosoftSystemCenterInstanceGroupLibrary7585010!Microsoft.SystemCenter.InstanceGroupContainsEntities"]$</RelationshipClass>
              <Expression>
                <SimpleExpression>
                  <ValueExpression>
                    <Property>$MPElement[Name="Type80531327bc2f439dba7c289399a2728e"]/AttributeDiscoveryGeneratedByUI9bc587a1ea5f4493a7d745766a57b922$</Property>
                  </ValueExpression>
                  <Operator>Equal</Operator>
                  <ValueExpression>
                    <Value>TEST</Value>
                  </ValueExpression>
                </SimpleExpression>
              </Expression>
            </MembershipRule>
<MembershipRule>
<MonitoringClass>$MPElement[Name="SystemCenter!Microsoft.SystemCenter.HealthServiceWatcher"]$</MonitoringClass>
<RelationshipClass>$MPElement[Name="MicrosoftSystemCenterInstanceGroupLibrary7585010!Microsoft.SystemCenter.InstanceGroupContainsEntities"]$</RelationshipClass>
<Expression>
    <Contains>
      <MonitoringClass>$MPElement[Name="SystemCenter!Microsoft.SystemCenter.HealthService"]$</MonitoringClass>
      <Expression>
        <Contained>
          <MonitoringClass>$MPElement[Name="MicrosoftWindowsLibrary7585010!Microsoft.Windows.Computer"]$</MonitoringClass>
          <Expression>
            <Contained>
              <MonitoringClass>$Target/Id$</MonitoringClass>
            </Contained>
          </Expression>
        </Contained>
      </Expression>
    </Contains>
</Expression>
</MembershipRule>
          </MembershipRules>
        </DataSource>
      </Discovery>
Thanks in advance. I have followed all the threads and I am not able to determine what is incorrect.
Mike Hanlon

Hi Mike,
Your group does not contain Windows Computers:
<MembershipRules>
            <MembershipRule>
              <MonitoringClass>$MPElement[Name="Type80531327bc2f439dba7c289399a2728e"]$</MonitoringClass>
That's why the second expression is always false.
http://OpsMgr.ru/

Data from repeating group not showing in preview

Hello experts,
I would like to consult with you regarding a problem I have in BI publisher.
I have tried creating a delivery receipt using BI publisher and when I preview it in word, everything is fine.
The problem is that when I finally upload to BI publisher and try to view it there, the data that is supposed to show up within the repeating groups are missing.
I have already validated the template before uploading and they look fine.
I also am doubtful that the cause is because of a lack of data source because I have some fields that are outside the repeating group, but they have been retrieved without any problems.
I have created a similar report using an older version of the XML Publisher and I didn't encounter a problem like this. I have also tried searching online but nothing really nails the problem that I am having. Do you have any insights regarding this?
Appreciate your soonest response on this. Thank you!
~Jovee

Hi sam thanks...I can see that data in extractor but not in PSA , that means it should not be in tra str /update rules/. the problem must be in extractor ...please help how to get this date in PSA as is...
I have one more issue, when Iam loading the data from PSA to cube the data was half loaded and then the remaining half has yellow status in monitor...when I checked in simulation mode the following message is coming " Enter rate USD / rate type M for 30.03.2007 in the system settings" do you have any idea on how to fix this ?
thanks
Edited by: sam on Jan 25, 2008 9:17 PM

RF Grouping not showing

Similar Messages

Maybe you are looking for