RF & particular SSID issue...

Hi All,
We are expereincing some strange problems.
1. One particular SSID's is appearing very low single strength & rest 2 SSID's are having good single strength from out of 3 SSID's advertised in one LAP.
2. Another issue is one of the particular SSID is not working from out of 2 SSID from  particular AP......in this issue client getting good single & we verifed WLAN settings are fine in the AP, also with the same WLAN settings this SSID Is working fine from other AP's.
Please let me know, if you have any idea in this issue.
Thanks,
Shrinivas

HI Vlad,
Another thing which you could try is to connect to both SSID (one at a time) from the same location  and verify if both the times you are connecting to the same AP. With this you will be able to verify if the both SSID signals are from same AP. This is really a trial and error methond. Also you may install netstumbler and verify the signal strength which you are receiving from each AP at given location.
Regards
Najaf

Similar Messages

  • Association Failed between AP and guest in particular SSID

    hi ,
    I would like to ask you for this issue , we have différents SSID in the same site one particular SSID does not work correcly  .
    The problème is that when ens station tray to connect in the network using this SSIG hotspot guest , the association failed .
    i have tried to launch some debug to undestand the reason , but without succèss :
    Debug client @ Mac of guest
    debug capwap event enable
    debug capwap detail enable
    the log that i, can see:
    *Apr 22 09:46:35.800: 00:21:6b:9a:90:a2 Deleting mobile on AP 00:1e:4a:8f:22:70(0)
    *Apr 22 09:47:15.457: 00:21:6b:9a:90:a2 Adding mobile on LWAPP AP 00:1e:4a:8f:22:70(0)
    *Apr 22 09:47:15.457: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 23) in 5 seconds
    *Apr 22 09:47:15.457: 00:21:6b:9a:90:a2 apfProcessProbeReq (apf_80211.c:4598) Changing state for mobile 00:21:6b:9a:90:a2 on AP 00:1e:4a:8f:22:70 from Idle to Probe
    *Apr 22 09:47:15.464: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:15.466: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:18.779: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:22.016: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:22.042: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:22.043: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:22.260: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:22.667: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:22.669: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:23.392: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:23.419: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:24.056: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:24.060: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:24.627: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    *Apr 22 09:47:24.630: 00:21:6b:9a:90:a2 Scheduling deletion of Mobile Station:  (callerId: 24) in 5 seconds
    i have see in this link :
    http://www.cisco.com/en/US/products/hw/wireless/ps430/products_tech_note09186a008091b08b.shtml
    you can see the attachement .
    May i have any help for this question.
    thank you in advance fior your help.

    It seems like you are doing EAP auth...
    as per logs... it seems like the radius is sending a Disconnect-Request to the client due to this log:
    apfMsDeleteByMscb Scheduling mobile for deletion with deleteReason 6, reasonCode 1
    However authentication is passing thru sucessfully it even receives an IP address from DHCP.
    So not sure what is going on  in there? please provide us details as stefanick has requested please.

  • Print Preview of particular page issue in SAP script

    Hi all,
    Kindly help me to resolve the following issue in SAPscript.
    I have a particular business requirement to preview a particular page in 'n' pages of a SAPscript.  After executing the sapscript calling program, the print window appears, in which i can choose particular page in the <b>Page Selection</b> Field.
    The problem is that the preview shows some other page rather than the appropriate page.  Please help me to resolve the issue.
    Awaiting for your replies,
    Thanks and Best Regards,
    Jana

    You need to call NEW-PAGE command in the sapscript when the user select a page in page selection.
    Try this:
    create the following text element in the sapscript in any window, preferibly MAIN window
    /E PBREAK
    /: NEW-PAGE &user_selected_page&
    In the Print program: OPEN_FORM returns a parameter called RESULT.
    case result-tdpageslct.
    when '2'.
    user_selected_page = <second page name in the sapscript>
    when '3'.
    user_selected_page = <third page name in the sapscript>
    when others.
    clear user_selected_page.
    endcase.
    if not user_selected_page is initial.
    call function WRITE_FORM and call above created text element
    endif.
    If the pages you are trying to display does not have main window, make sure next page in the page definition is not the same page in the sapscript.
    Regards
    Sridhar

  • Broadcast and non-broadcast SSID issues with iPhones and iPads

    We have a CIsco wireless infrastructure configured with a public broadcasted ssid and a private non-broadcast ssid that we are experiencing issues with the iPads and iPhones.  The iPad or iPhone will switch between both ssids if defined but keep the original IP address when it switches to the non-broadcast ssid making it unusable.  It shouldn't be switching at all technically.  If the non-broadcast ssid is defined only on the iPhone or iPad, the broadcast ssid pops up and starts asking for authentication information.  I have Cisco looking into this but I'm quite sure this is an Apple bug. Any other device works fine.  We are currently using version 4.3.5(8L2) on the iPads and iPhones.  I do know that if we broadcast both SSIDS, the issue goes away, but I don't want to do that.  Although it doesn't really add any more security, it just isn't advertised, so most people won't see it and avoids a lot of questions. Hopefully there's a simple solution. 
    Any ideas apple guys?
    Also how does one open an actual trouble ticket with apple?

    Did you solve this?  Settings\Wifi\Askto join networks - OFF

  • AP1131 multiple SSID issue

    Hello,
    Very new to Cisco wireless, trying to figure this out.
    I have an ASA that will be handling the VLAN traffic.
    VLAN1 = default internal VLAN.
    VLAN10 = guest VLAN.
    On my AP1131 I want to have "Staff" SSID associated with VLAN1,
    and "Guest" SSID associated with VLAN10.
    Interfaces 6 & 7 on the ASA are PoE so I think I'm good on that.  I have those two ports on the ASA set as trunks with Vlan1 as native.
    My biggest pain right now is that I can't seem to get "Guest" and "Staff" broadcasting at the same time!
    I don't really need the "A" radio, so I'm just trying to get the two SSID's broadcasting on the "G" radio.
    I'm configuring via the GUI, but frequently looking back at the CLI.
    Is this a common issue?  Something that someone can point to a common mistake?
    Attached is running-config; though I'm still very much playing with it.

    Hi Scott,
    Check out these two excellent related threads
    https://supportforums.cisco.com/message/1308205#1308205
    https://supportforums.cisco.com/message/1286462#1286462
    Cheers!
    Rob
    Please support CSC Helps Haiti
    https://supportforums.cisco.com/docs/DOC-8895
    https://supportforums.cisco.com/docs/DOC-8727

  • WEBAUTH SSID ISSUE

    /* Style Definitions */
    table.MsoNormalTable
    {mso-style-name:"Tableau Normal";
    mso-tstyle-rowband-size:0;
    mso-tstyle-colband-size:0;
    mso-style-noshow:yes;
    mso-style-parent:"";
    mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
    mso-para-margin:0cm;
    mso-para-margin-bottom:.0001pt;
    mso-pagination:widow-orphan;
    font-size:10.0pt;
    font-family:"Times New Roman";
    mso-ansi-language:#0400;
    mso-fareast-language:#0400;
    mso-bidi-language:#0400;}
    hello,
    We do have some troubles regarding an SSID  , i have wism controller version  5.2.193, three Wlans are configured each one broadcasting  in diffrrent range SSID TESTGUEST  on 802.11g,SSID 2 on 802.11a,SSID 3 on 802.11b, i do have some  trouble with SSID TESTGUEST used for Guest access using Webauth as security methode to authenticate users  with predifined local users accounts, the symptoms are  users can see the SSSID TESTGUEST  beacons but can not get access (no login page ).
    Note :i have noticed  some errors regarding lwapp since  we know that we are unsing  5.2.193 we should have capwap error instead of lwapp .
    logging;
    (WiSM-slot2-2) >show logging   if you need more info let me know
    regargs
    Logging to buffer :
    - Logging of system messages to buffer :
      - Logging filter level.......................... warnings
      - Number of system messages logged.............. 3099008
      - Number of system messages dropped............. 158275
    - Logging of debug messages to buffer ........... Disabled
      - Number of debug messages logged............... 0
      - Number of debug messages dropped.............. 0
    Logging to console :
    - Logging of system messages to console :
      - Logging filter level.......................... errors
      - Number of system messages logged.............. 0
      - Number of system messages dropped............. 3257283
    - Logging of debug messages to console .......... Enabled
      - Number of debug messages logged............... 0
      - Number of debug messages dropped.............. 0
    Logging to syslog :
    - Syslog facility................................ local1
    - Logging of system messages to syslog :
      - Logging filter level.......................... warnings
      - Number of system messages logged.............. 3099008
    --More-- or (q)uit
      - Number of system messages dropped............. 158275
    - Logging of debug messages to syslog ........... Disabled
      - Number of debug messages logged............... 0
      - Number of debug messages dropped.............. 0
    - Number of remote syslog hosts.................. 1
       - Host 0....................................... 198.235.125.20
       - Host 1....................................... Not Configured
       - Host 2....................................... Not Configured
    Logging of traceback............................. Enabled
    - Traceback logging level........................ debugging
    Logging of process information................... Enabled
    Logging of source file informational............. Enabled
    Timestamping of messages.........................
    - Timestamping of system messages................ Enabled
      - Timestamp format.............................. Date and Time
    - Timestamping of debug messages................. Enabled
      - Timestamp format.............................. Date and Time
    Logging buffer (3099008 logged, 158275 dropped)
    *Dec 10 10:42:07.157: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:07.085: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.993: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.911: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.829: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.767: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.702: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.639: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.496: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:d7:93:3b:d0
    *Dec 10 10:42:06.448: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.292: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:55:b9:c0 Previous message occurred 3 times.
    *Dec 10 10:42:06.139: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned          L7_FAILURE                                                             
    *Dec 10 10:42:06.138: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:42:06.125: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:06.048: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.992: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.915: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.832: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.748: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.694: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.633: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.549: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:42:05.549: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.483: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.411: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:42:05.345: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0 Previous message occurred 3 times.
    *Dec 10 10:42:05.051: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:42:04.911: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:6b:30
    *Dec 10 10:42:03.602: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:6b:30
    *Dec 10 10:42:03.142: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:18:de:b3:ba:7b, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.51/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:42:02.568: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:41:59.867: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:58.350: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:57.568: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.Previous message occurred 2 times.
    *Dec 10 10:41:57.380: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:57.379: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:57.292: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE Previous message occurred 3 times.
    *Dec 10 10:41:56.519: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:56.416: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE                                                                                  
    *Dec 10 10:41:56.067: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:21:5c:89:a4:33, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.31/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:41:56.053: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:0a:32:d0 Previous message occurred 2 times.
    *Dec 10 10:41:55.418: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:55.417: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:55.136: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:1b:77:15:a1:31
    *Dec 10 10:41:54.922: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1d:71:23:74:20
    *Dec 10 10:41:54.569: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:21:5c:89:a4:33, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.31/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:41:54.470: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:54.169: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE Previous message occurred 3 times.
    *Dec 10 10:41:54.168: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:54.167: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:53.539: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:75:f0
    *Dec 10 10:41:53.324: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmissions exceeded for client 00:21:5c:97:90:9f Previous message occurred 2 times.
    *Dec 10 10:41:51.627: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:51.522: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1d:71:23:74:20
    *Dec 10 10:41:51.224: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:41:50.139: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:55:8a:f0
    *Dec 10 10:41:49.057: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:49.056: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:48.932: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmissions exceeded for client 00:1b:77:15:71:13
    *Dec 10 10:41:48.753: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:6d:b9:6a:30
    *Dec 10 10:41:47.985: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:47.984: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:47.648: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:46.437: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:le returned L7_FAILURE Previous message occurred 2 times.
    *Dec 10 10:41:46.436: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:46.435: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned _FAILURE                                                                                      Previous message occurred 2 times.
    *Dec 10 10:41:45.762: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:43.201: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:41:43.011: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:1c:bf:61:fa:da
    *Dec 10 10:41:43.010: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:41:41.464: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:6b:30
    *Dec 10 10:41:40.072: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:0a:32:d0
    *Dec 10 10:41:38.940: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1d:71:23:74:20
    *Dec 10 10:41:37.497: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE                                                                                                            Previous message occurred 2 times.
    *Dec 10 10:41:37.496: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:36.898: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:41:36.739: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:36.738: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:36.242: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:41:35.370: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmissions exceeded for client 00:18:de:3e:74:79
    *Dec 10 10:41:35.320: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:41:34.302: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:13:ce:29:e2:4c, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.243/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:41:33.808: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:41:33.304: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:13:ce:29:e2:4c, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.243/TPA(Destination IP Address) 192.168.252.1 Previous message occurred 2 times.
    *Dec 10 10:41:32.274: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:32.273: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAI
    *Dec 10 10:41:32.178: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:13:ce:29:e2:4c, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.243/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:41:30.624: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:55:b9:c0
    *Dec 10 10:41:30.056: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:41:29.968: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:41:29.965: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE revious message occurred 3 times.
    *Dec 10 10:40:58.813: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:56:0d:a0
    *Dec 10 10:40:58.491: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:19:7d:58:a0:f9, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.28/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:40:58.125: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:40:57.429: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:0a:32:d0
    *Dec 10 10:40:56.980: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:19:7d:58:a0:f9, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.28/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:40:56.188: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:56.043: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:7c:b0
    *Dec 10 10:40:55.964: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:19:7d:58:a0:f9, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.28/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:40:54.744: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:54.105: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:54.104: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:53.924: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:51.195: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:50.295: %APF-3-USER_DEL_FAILED: apf_ms.c:5071 Unable to delete username CORP\mxcrawle for mobile 00:40:96:b5:58:8c
    *Dec 10 10:40:49.724: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:48.372: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:56:0d:a0
    *Dec 10 10:40:47.813: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:47.640: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:47.336: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:46.991: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:75:f0
    *Dec 10 10:40:46.154: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:45.710: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:45.605: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:6b:30
    *Dec 10 10:40:45.520: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:1c:bf:61:fa:da
    *Dec 10 10:40:45.519: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:45.138: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:23:7a:51:47:d7
    *Dec 10 10:40:45.137: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:44.714: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:43.216: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:43.215: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:43.159: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.Previous message occurred 2 times.
    *Dec 10 10:40:42.951: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:
    *Dec 10 10:40:42.155: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:16:6f:46:42:2f, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.12/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:40:41.700: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmissions exceeded for client 00:21:5c:6f:f7:3f
    *Dec 10 10:40:41.684: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE Previous message occurred 3 times.
    *Dec 10 10:40:41.683: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:41.682: %RRM-3-RRM_LOGMSG: rrmLrad
    *Dec 10 10:40:30.713: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:29.453: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:6b:30
    *Dec 10 10:40:28.874: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:28.094: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:40:27.268: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:26.610: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmissions exceeded for client 00:21:5c:97:90:9f
    *Dec 10 10:40:26.580: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:21:5c:8a:ac:5b, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.219/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:40:26.325: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:26.307: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:26.219: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE                       Previous message occurred 2 times.
    *Dec 10 10:40:26.218: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: M Verify Coverage Hole returned L7_FAILURE *Dec 10 10:40:25.735: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:25.273: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA Previous message occurred 3 times.
    *Dec 10 10:40:25.253: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE                                                                                                         
    *Dec 10 10:40:25.252: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:25.081: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:21:5c:8a:ac:5b, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.219/TPA(Destination IP Address) 192.168.252.1 Previous message occurred 3 times.
    *Dec 10 10:40:24.249: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:24.247: %LWAPP-4-SIG_INFO1: spam_lrad.c:28010 Signature information; AP 00:1e:13:ee:08:10, alarm ON, standard sig Deauth flood, track per-Macprecedence 9, hits 300, slot 0, channel 11, most offending MAC 00:1e:7a:70:6a:e0
    *Dec 10 10:40:24.064: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:21:5c:8a:ac:5b, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.219/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:40:22.966: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:22.755: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:22.755: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE  Previous message occurred 3 times.
    *Dec 10 10:40:22.754: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:22.566: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication aborted for client 00:1b:77:15:71:13
    *Dec 10 10:40:22.145: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:55:8a:f0
    *Dec 10 10:40:21.016: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1d:71:23:74:20
    *Dec 10 10:40:20.531: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.Previous message occurred 2 times.
    *Dec 10 10:40:20.296: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:19.636: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:6d:b9:6a:30
    *Dec 10 10:40:17.983: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILUR
    *Dec 10 10:40:17.983: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE    Previous message occurred 2 times.
    *Dec 10 10:40:16.988: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:16.870: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:16.870: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:1f:3b:63:6d:f5
    *Dec 10 10:40:16.869: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:16.617: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG: RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:16.420: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:15.206: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE                                                                                                            Previous message occurred 3 times.
    *Dec 10 10:40:15.205: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:14.340: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:14.339: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:12.667: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:40:10.585: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:75:f0
    *Dec 10 10:40:09.944: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:09.203: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:0a:32:d0
    *Dec 10 10:40:08.062: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1d:71:23:74:20
    *Dec 10 10:40:07.246: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:21:5c:17:73:79
    *Dec 10 10:40:07.245: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication aborted for client 00:21:5c:17:73:79 Previous message occurred 2 times.
    *Dec 10 10:40:06.414: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:06.413: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE                        Previous message occurred 2 times.
    *Dec 10 10:40:06.308: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:40:05.389: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:6b:30
    *Dec 10 10:40:04.857: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:40:04.004: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:6d:b9:6a:30
    *Dec 10 10:40:02.620: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:55:8a:f0
    *Dec 10 10:40:02.013: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:40:00.866: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE                                                                                                     
    *Dec 10 10:40:00.866: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE  Previous message occurred 2 times.
    *Dec 10 10:40:00.865: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returne
    *Dec 10 10:40:00.283: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:40:00.228: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:40:00.170: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:40:00.107: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:40:00.040: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:59.943: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:59.878: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:59.813: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:59.674: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:39:59.063: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:39:59.062: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:39:58.244: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE Previous message occurred 2 times.
    *Dec 10 10:39:58.243: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE                                                                                                         
    *Dec 10 10:39:58.242: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:39:57.243: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:9d:da:cc:d0
    *Dec 10 10:39:56.674: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.624: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:16:6f:7f:70:55
    *Dec 10 10:39:56.623: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:39:56.607: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.546: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.475: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.417: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.362: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.295: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.223: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.159: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.103: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:56.041: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.972: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.915: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.847: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.787: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.711: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.652: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.597: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.534: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.461: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.430: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:39:55.393: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.327: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:21:1c:79:0e:f0
    *Dec 10 10:39:55.090: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:0a:32:d0
    *Dec 10 10:39:54.230: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:39:54.123: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:39:54.062: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:39:54.061: %RRM-3-RRM_LOGMSG: rrmLrad.c:2471 RRM LOG:RRM Verify Coverage Hole returned L7_FAILURE
    *Dec 10 10:39:53.709: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:c7:75:f0
    *Dec 10 10:39:53.567: %DOT1X-3-MAX_EAP_RETRANS: 1x_ptsm.c:426 Max EAP retransmissions exceeded for client 00:1b:77:15:b7:ed
    *Dec 10 10:39:53.353: %APF-4-ASSOCREQ_PROC_FAILED: apf_80211.c:3682 Failed to process an association request from 00:0c:f1:29:b7:6a. WLAN:1, SSID:TESTGUEST. Conflicting extended supported rates in message.
    *Dec 10 10:39:53.138: %DHCP-4-REQIP_NOT_PRESENT: dhcpd.c:299 Received a packet without a requested ip!.
    *Dec 10 10:39:52.619: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:1f:3b:5d:4e:c7, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.177/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:39:52.318: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:1f:27:56:0d:a0
    *Dec 10 10:39:51.118: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:1f:3b:5d:4e:c7, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.177/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:39:50.370: %LWAPP-3-VALIDATE_ERR: spam_lrad.c:8966 Validation of SPAM Vendor Specific Payload failed - AP  00:18:74:0a:32:d0
    *Dec 10 10:39:50.100: %DTL-1-ARP_POISON_DETECTED: dtl_net.c:1415 STA(Target MAC Address) [00:1f:3b:5d:4e:c7, 0.0.0.0] ARP (op ARP REQUEST) received with invalid SPA(Source IP Address) 192.168.254.177/TPA(Destination IP Address) 192.168.252.1
    *Dec 10 10:39:49.357: %DOT1X-1-INVALID_WPA_KEY_STATE: 1x_eapkey.c:1584 Received EAPOL-key message while in invalid state (4) - version 2, type 3, descriptor 2, client 00:90:7a:02:d3:04
    *Dec 10 10:39:49.273: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447 Authentication aborted for client 00:21:5c:17:73:79
    *Dec 10 10:39:48.220: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA
    *Dec 10 10:39:48.220: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:2856 Max EAP identity request retries (3) exceeded for client 00:1c:bf:61:fa:da
    *Dec 10 10:39:48.219: %DOT1X-4-INVALID_MSG_TYPE: authlib.c:84 Invalid message type 9 received from AAA

         you should try connecting to the guest WLAN, and once you are connected open a broswer and go to http://74.125.19.104  if this works, then you need to check that UDP 53 , DNS queries, are allowed from the guest vlan

  • 3850 WLC - 5760 Anchor: Multiple Guest SSIDs issue

    Hi,
    I have configured a 3850 Foreign WLC and a 5760 as anchor WLC in a DMZ behind an ASA FW. The Anchor Controller is configured to advertise 3 GUEST Wireless:
    (INSIDE) ---- ASA FW (guest in interface) -------------------------- (Te1/0/1) 5760 ANCHOR (Te1/0/2) -------------------- L3 Link-------------------- (guest out interface) ASA FW ---- (OUTSIDE)
    GUEST1: 10.9.65.0/24 – VLAN 11
    GUEST2: 10.9.66.0/24 – VLAN 12
    GUEST3: 10.9.67.0/24 – VLAN 13
    Management VLAN 1: 10.8.252.1 (Anchor Management VLAN – Mobility)
    The link between the WLC and the Guest OUT Interface on the ASA Firewall is a L3 Link, NOT a Trunk.
    The 5760 WLC is also a DHCP server for the three client VLANs above. I have also configured 3 SVIs as default gateways for these VLANs:
    Interface vlan 11 – 10.9.65.1
    Interface vlan 12 – 10.9.66.1
    Interface vlan 13 – 10.9.67.1
    wgh-anchorwlc5760-primary#show ip interface brief
    Interface              IP-Address      OK? Method Status                Protocol
    Vlan1                  10.8.252.1      YES NVRAM  up                    up
    Vlan11                 10.9.65.1       YES manual up                    up
    Vlan12                 10.9.66.1       YES manual up                    up
    Vlan13                 10.9.67.1       YES manual up                    up
    GigabitEthernet0/0     10.8.252.85     YES NVRAM  down                  down
    Te1/0/1                unassigned      YES unset  up                    up
    Te1/0/2                10.8.253.1      YES NVRAM  up                    up
    Capwap0                unassigned      YES unset  up                    up
    If a client connects to GUEST1 SSID it gets an IP address in VLAN 11 and its default gateway is 10.9.65.1.
    If a client connects to GUEST2 SSID it gets an IP address in VLAN 12 and its default gateway is 10.9.66.1.
    If a client connects to GUEST3 SSID it gets an IP address in VLAN 13 and its default gateway is 10.9.67.1.
    Mobility is UP and I can see clients connected to the Anchor WLC either in IPLEARN or WEBAUTH_PEND state. DHCP is working fine, clients get an IP and the right default gateway and DNS servers when connect, for example, to GUEST1.
    anchorwlc5760-primary#show wireless client summary
    Number of Local Clients : 3
    MAC Address    AP Name                          WLAN State              Protocol
    04f7.e482.b21c N/A                              2    IPLEARN            Mobile
    bc3e.6d32.17f6 N/A                              2    IPLEARN            Mobile
    a826.d5b3.5ae8 N/A                              2    WEBAUTH_PEND       Mobile
    However, they are not able to ping the default gateway – SVI VLAN 11: 10.9.65.1, so I can not see any traffic leaving the Anchor WLC to continue with the Web Authentication Process (cwa) using ISE. I can see that the authorization policy (“unkown” and the URL to ISE) has been pushed to the clients but I am not redirected to ISE Web Authentication Portal when I open my web browser. I have done some captures on the FW interfaces but I cannot see any traffic coming from the clients.
    I know that usually there is a Trunk (that allows client VLANs) between a WLC and L3 Switch when you configure multiples SSIDs and then configure the SVIs on the L3 Switch. However, I think this design with a L3 Link should work too because 5760 is a WLC+L3Switch.
    My question is: Why clients are not able to ping their default gateway?
    I hope it makes sense.
    I appreciate any thoughts and help. Thanks in advance.
    Joana.

    Hi,
    I couldn't get it working (I doubt if it is really possible). I had to add a switch between the 5760 Anchor Controller and the ASA Firewall:
    (INSIDE) ---- ASA FW (guest in interface) -------------------------- (Te1/0/1) 5760 ANCHOR (Te1/0/2) -------------------- SWITCH-------------------- (guest out interface) ASA FW ---- (OUTSIDE)
    The link between the 5760 and the Switch is configured as a Trunk and it allows the 3 Guest SSIDs (VLANs). The link between the Switch and the ASA FW is configured as a Layer 3 link. I also set up the default gateways for the 3 GUEST VLANs in the Switch (3 vlan interfaces) and the 5760 as DHCP Server.
    I hope it helps.
    Joana.

  • WLC4400 + FreeRadius Restrict user to a particular SSID

    Hi,
    I'm building a lab with WLC4404 and freeradius + daloradius gui.
    WLC can comunicate with the freeradius but my problem is that the users can login and no  matter in which SSID they connect they get in.
    I want to know the way to policy this on the freeradius or the WLC with the AVpairs as every user should remain in a specific SSID.
    Thanks,

    Hi,
    Right now the freeradius is passing the ssid value to the WLC but when the user is registered it get moved from the assigned vlan in freeradius to the one that he try to connect.
    This is the message of the WLC:
    DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:577 Disconnecting mobile #:#:#:#:#:# due to switch of WLANs from 3(STAFF) to 1(STUDENTS)
    Is any way to change this WLC behavior so if the assigned WLAN is not the same as the one that the user is trying to connect the WLC reject the connection.
    Thanks,

  • WCS used to configure SSID broadcast for WLAN issue

    Hi,
    When I try to disable the broadcast parameter for an SSID on a WLC using WCS (4.0.96.0), I am running in to some issues.
    I uncheck the 'Broadcast SSID' check box for a particular SSID and then submit the change. But, after I submit, the check box is still checked. If I verify the setting on the native WLC web interface, the Broadcast SSID parameter is still enabled.
    I can change other parameters OK, so I don't have an SNMP issue.
    If you perform this operation from the WLC web interface or the command line, you have to disable the WLAN first, before the SSID broadcast can be switched off.
    I suspect that WCS doesn't have the intelligence to disable and re-enable the WLAN to perform this operation. But, it very frustrating that it doesn't even generate a warning or failure message to say that the operation has failed.
    Anyone seen this or can perhaps tell me if I am mis-operating WCS in some way ?
    Thanks.

    The WLANs tab allows you to create, configure, and delete WLANs on your controller.
    You can access the following pages from the WLANs menu bar selection:
    WLANs
    WLANs > New
    WLANs > Edit
    WLANs > Mobility Anchors
    AP Groups VLAN

  • Control record issue !

    Hi All,
    I am handling UK Payroll and got an issues related to payroll run and control record,
    Issue 1: The payroll driver (RPCALCG0) has skipped around 1500 Employees against payroll run for particular period
    Issue 2: How control record allowed user to Exit control record for period in which EE's skipped in payroll
    Please provide your valuable suggesting in regard to resolve the above two issues,
    Thanks in advance.
    Regards,
    Devendra Reddy D.

    Hi,
    Issue 1: The payroll driver (RPCALCG0) has skipped around 1500 Employees against payroll run for particular period
    Say you want to run payroll for FEB..
    But payroll control record may not be in FEB... It may be in March..
    Issue 2: How control record allowed user to Exit control record for period in which EE's skipped in payroll
    Payroll control record may have been deleted on the month of Jan..& been set in Release mode in March month directly...
    So feb month gets skipped & Exit mode in Feb is skipped too...
    For detailed info.. Go to PA03 enter payroll ares & click display option..
    Under Go To tab.. look for Control Record Log..
    Regards,
    Veeram

  • How to create a sequence for an particular item in my apex form

    Hi friends,
    I created an database application, of a form with a report, and it is working fine...
    But in my form, i have a requirement....The below are the existing fields in my form
    issue no
    created by
    start date
    status
    priority
    due date
    Among these fields in my form i need to create a 'Sequence' for my field "issue no",
    So that whenever i opened the form the 'issue number' must generate automatically like 1 for the first time, 2 for the second time and so on..
    For that i created a sequence
    CREATE SEQUENCE "ORDERS_SEQ"
    MINVALUE 1
    MAXVALUE 999999999999999999999999999
    INCREMENT BY 1
    START WITH 1000
    NOCACHE
    NOCYCLE;
    But for validation where i need to write the sequence query for the particular item 'issue no'....i dont have any idea of where to write the validation query for the sequence..
    please tell where i need to write in step wise manner..please help me friends...
    As the below is my validated sequence query for item 'issue no'
    'select seq.issue_id.nextval into issue_no'
    This is my above validation query whether the query that i mentioned is right..if not let me know the validation query..
    And also i need where to apply this validation query in steps..
    Thanks in advance
    Regards,
    Harry...

    Harry,
    Rik is on the right track. Here is a sample insert trigger: Would need to substitute you sequence ORDERS_SEQ with my sequence las_log_seq, how you define or use timestamps is up to you.
    DROP TRIGGER LASDEV.BINS1_LAS_LOG_TBL;
    CREATE OR REPLACE TRIGGER LASDEV."BINS1_LAS_LOG_TBL"
       BEFORE INSERT
       ON las_log_tbl
       FOR EACH ROW
    BEGIN
       -- Description: Insert log_seq, creation_dt, creation_id,
       --              lst_updt_dt and lst_updt_id.
       -- Maintenance:
       -- Date        Actor          Action
       -- ====        =====          ======
       -- 07-Sep-2010 J. Wells       Create.
       :new.creation_id := nvl( v( 'app_user' ), user );
       :new.creation_dt := SYSDATE;
       :new.lst_updt_dt := :new.creation_dt;
       :new.lst_updt_id := :new.creation_id;
        SELECT las_log_seq.NEXTVAL
          INTO :new.las_log_seq
          FROM DUAL;
    END bins1_las_log_tbl;
    /Heff

  • Mac Pro w/ Lion Having Issues

    Every since I upgraded my early 2009 Mac Pro 2.66 Quad-core Xeon, I've been having some strange issues.
    For example, my accounts were set to log out after a certain amount of time of inactivity. By the time the account logged out, my display would have gone to sleep. When I woke my display to login by clicking the mouse or pressing a key on the keyboard, my display would only show about a quarter of an inch around the mouse pointer. When I further moved the mouse pointer, the display only drew where the pointer had gone.
    Now my accounts simply lock after a period of inactivity. When I unlock the account, the translucent menu bar on the top of the screen shows a different desktop picture than the rest of the screen. When the desktop either changes or I change to another workspace, the menu bar will change also and match the rest of the screen.
    Also, I've been having a lot of issues with my DVD program accepting the disks that are loaded into the player. The only way to get the DVD player to accept the DVD is to restart the computer (logging out works sometimes, but not all of the time.)
    On a different note, my Mac Pro does not go to sleep by itself and hasn't since the summer of 2009. I've tried everything including turning all network connections off -- nothing has helped. I have to put my Mac Pro to sleep manually. Strangely, my Mac Pro sleeps just fine with Windows 7. Hmmm...
    I've performed about three clean installs of Lion hoping that would resolve the issues I'm experiencing. Clean installs didn't help.
    I wonder if maybe my video card is getting old and causing some of these issues -- particularly those issues related to the display.
    Below are my specs:
    Mac Pro
    Early 2009
    Processor: 2.66 GHz Quad-Core Intel Xeon
    Memory: 8 GB 1066 MHz DDR3 EEC
    Graphics: NVIDIA GeForce GT 120 512 MB
    Software: OS X Server Lion 10.7.2 (11C74)

    That sounds like several different issues, and some of them pre-date Lion. Upgrading is unlikely to ever solve pre-existing problems and more likely to further exacerbate them.
    One the 'no sleep' problem. Do you mean the display or the hard disk sleep? I'm assuming you've already looked at the settings in Energy saver. It sounds to me like you have something running in the background that is preventing the hard disk from sleeping. Lots of programs can do this, including iTunes, Transmission or anything that causes hard disk activity. If you can't think of anything that is obviously running, have a look in your login items ( > System Preferences > Users & Groups | Login Items) for some background process (little snitch? clamxav? or anything that scans your system).

  • Goods Issue ./ Serial Number Report

    Guys,
    I want to create a report which gives me the Goods Issue details with the items in the goods issue and Serial Numbers processed in those particular goods issues.
    The problem is that with the following coding, it is returning all the Serial Numbers related to the particular item available in SAP and not only those relating to that particular Goods Issue.  So if I have a quantity of 2 Serial Numbers for one item, it is not returning to Serial Numbers for that Goods Issue, but it is returning all Serial Numbers of the System under that Item.
    I suspect that it is a JOIN problem, what do you think?
    Coding is:
    Select
                        T0.DocDate as 'Goods Issue Date'
    ,                    T0.DocNum as 'Goods Issue Reference'
    ,                    T1.ItemCode as 'Item Code'
    ,                    T1.Dscription as 'Item Description'
    ,                    T2.IntrSerial as 'Serial Number'
    ,                    T1.OcrCode as 'Cost Centre'
    ,                    T1.LineTotal as 'Total Cost'
    ,                    T1.U_eReasonCode as 'Reason Code'
    ,                    T0.Comments as 'Remarks'
    From
                        OIGE T0 JOIN IGE1 T1 ON T0.DocEntry = T1.DocEntry
                                  LEFT OUTER JOIN OSRI T2 ON T1.ItemCode = T2.ItemCode
    Order By
                        T0.DocNum
    Many thanks for your work everyone.
    Regards,
    Vankri

    Hi,
    You can go to Inventory >>> Inventory Report >>> Serial Number Transaction Report. There are a lot of criteria you can choose to generate your own report.
    In your case, choose Dates and Documents tab and then enter your criteria.
    Hope this helps,
    Son.

  • ITunes for 64bit Windows 7 Driver/CD/DVD/Drive Issues-

    Hi There
    I am sure that there are many many users out there suffering the same frustration as me in regard to ITunes just not working properly with Windoews 7 (64Bit).
    I have been trying to solve the mystery of "ITunes for Windows Registry Settings Warning When Opening Itunes.
    I have tried all the recommended actions to correct this problem without any success and I do mean ALL.
    Below is a screen shot of my registry, can anyone see anything wrong with it?
    In the meantime (Last four months) I have stopped using ITunes and instead have used Digital 7, this will be my very last attempt to get ITunes working properly, failure will mean consigning ITunes to the same place as any other Software that does not do wshat it says on the can.
    I hope someone can help.

    That's good that it is in device manager, but what about in Computer with the rest of the drivers?
    Also, are the drives listed in Computer and device manager or just device manager?
    I want to verify if the symptoms are present for a particular software issue before looking at other issues.  I really doubt it is a driver issue at this point.  If it was, then I suspect the issue would be present from day one. 
    It could be that the lens has dust buildup preventing it from working properly.  They do make CD cleaning kits that have a special CD designed to clean the laser as it passes over the lens.  If you happen to have one of these, or access to one, I recommend trying this step to make sure it isn't as simple as dust buildup interfering with the laser. 
    It could also be hardware failure, but I would like to try a few other steps before coming to that conclusion. 
    It may be worth reviewing this document as it covers a lot of the most common issues behind DVD drive issues. Feel free to skip any steps you have already tried. 
    Let me know what happens. 
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • I still have Cd/DVD drive issues

    The CD is ejected after a short while and never mounted. I have cleaned the optics of the CD drive and reset my PRAM.
    Has anybody discovered a complete solution for this problem.

    That's good that it is in device manager, but what about in Computer with the rest of the drivers?
    Also, are the drives listed in Computer and device manager or just device manager?
    I want to verify if the symptoms are present for a particular software issue before looking at other issues.  I really doubt it is a driver issue at this point.  If it was, then I suspect the issue would be present from day one. 
    It could be that the lens has dust buildup preventing it from working properly.  They do make CD cleaning kits that have a special CD designed to clean the laser as it passes over the lens.  If you happen to have one of these, or access to one, I recommend trying this step to make sure it isn't as simple as dust buildup interfering with the laser. 
    It could also be hardware failure, but I would like to try a few other steps before coming to that conclusion. 
    It may be worth reviewing this document as it covers a lot of the most common issues behind DVD drive issues. Feel free to skip any steps you have already tried. 
    Let me know what happens. 
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Maybe you are looking for

  • Application for the post of an ORACLE DBA

    ================================================================= ============ ARUNKUMAR RAGHAVAN MSc,BEd,PGDMCH,(MBA) ================================================================= ============ CURRICULUM VITAE Covering letter      From Arunkumar

  • Display resolution setting

    Somehow I changed the resolution setting for the display on my MacBook. Now I'm not sure what to set it. I currently have it on 1280 X 800, but I'm not sure that is right. Any help will be appreciated.

  • Best way to do analysis of data

    I have 18,000 or so records, each marked with a date field, and each recording the elapsed time it took to perform some action, in seconds, as of a particular hour/minute/second. For example: TESTTIME         TESTDURATION 7:03:21          2.4 7:03:32

  • Cant find "my bookshelf"

    I supposedly downloaded a textbook I need for school on firefox. Supposedly. In calling, I was told it would be downloaded but to call back if it did not. I cannot even seem to get to "my bookshelf" so I can check, though meanwhile, I am still paying

  • Photoshop CS6 - undo shortcut issues

    I am using Photoshop CS6 on Mac OSX 10.10. When I attempt to use the undo shortcut (Command Z), it only sometimes works. If it doesn't work, I have to manually go to Edit - Undo. Is there a fix for this?