RFC Timeout issue in SAP

Hi,
I have a RFC Fucntion Module in SAP Z_BC1_BAPI_PO_CREATE02 which creates a PO using BAPI_PO_CREATE1. When I debug it using sm50 transaction I get a RFC timeout after it leaves my RFC program. I checked the RZ10 transaction and the timeout is OK. However the problem is occurs when the control leaves the RFC Function Module and moves into a sub-routine pool LZZ_M3_PURCHASEORDER02V01 where a Form exists FORM Z_BC1_BAPI_PO_CREATE02 %_RFC. which includes a FM
Assign default values
Call remote function
CALL FUNCTION 'Z_BC1_BAPI_PO_CREATE02' %_RFC
Looking forward to your inputs. This is an interface between SAP / webmethods and Ariba.
cheers
Aveek

no i dont get the timeout in sap.
cheers
aveek

Similar Messages

Timeout issues in synchronous webservices

Hi Everybody,
I am working on a synchronous webservice Interface in which sender is a Webservice and receiver is BAPI (RFC) and I need to handle the time out issue when i dont get the response from the receiver SAP system.Also need to raise an alert.
Can anybody help me out on this.
Helpful answers will be rewarded points.
Regards,
RK

Hi,
For the timeout issue look at these:
Web Service Timeout Configuration
SOAP adapter - Module options...
For the alert I think you should take a look at these:
Does XI support standard SOAP Fault exceptions?
SOAP Fault message (***)
Handling Web Service SOAP Fault Responses in SAP NetWeaver XI
Hope it helps.
Best Regards,
Arman
(Please mark your question as answered when it is solved)

Svn with Apache Timeout issue

Hello Archers,
I've set up an svn Server with Apache folloing your wiki on my raspberry pi.
https://wiki.archlinux.org/index.php/LAMP
https://wiki.archlinux.org/index.php/Subversion_Setup
Unfortunately I get errors when I try to commit several files (15 or so). I think it is a timeout issue, however I don't know where to specify the timeout in the httpd.conf (or httpd-ssl.conf)
This is a client error message:
Commit failed (details follow):
Unexpected end of svndiff Input
And this the corresponding server side log:
[date] [dav:error] [pid 448:tid 2854220848] (70007)The timeout specified has expired: [client 192.168.178.55:63819] Timeout reading the body (URI: /Dokumente/!svn/txr/9-q/Music/myfile.mp3) [408, #0]
[date] [dav:error] [pid 448:tid 2854220848] [client 192.168.178.55:63819] mod_dav_svn close_stream: error closing write stream [500, #185004]
[date] [dav:error] [pid 448:tid 2854220848] [client 192.168.178.55:63819] Unexpected end of svndiff input [500, #185004]
I assume it is some error like this: http://subversion.apache.org/faq.html#s … -truncated
I think I don't have specified the timeouts correctly, since I haven't found the default option.
tl:dr
Do you know how to set the timeouts in the apache configuration file?
I very much appreciate your help.
arch on pi
Here are my configuration Files with my position for the timeout order:
httpd-ssl.conf:
# This is the Apache server configuration file providing SSL support.
# It contains the configuration directives to instruct the server how to
# serve pages over an https connection. For detailed information about these
# directives see <URL:http://httpd.apache.org/docs/2.4/mod/mod_ssl.html>
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Required modules: mod_log_config, mod_setenvif, mod_ssl,
# socache_shmcb_module (for default value of SSLSessionCache)
# Pseudo Random Number Generator (PRNG):
# Configure one or more sources to seed the PRNG of the SSL library.
# The seed data should be of good random quality.
# WARNING! On some platforms /dev/random blocks if not enough entropy
# is available. This means you then cannot use the /dev/random device
# because it would lead to very long connection times (as long as
# it requires to make more entropy available). But usually those
# platforms additionally provide a /dev/urandom device which doesn't
# block. So, if available, use this one instead. Read the mod_ssl User
# Manual for more details.
#SSLRandomSeed startup file:/dev/random 512
SSLRandomSeed startup file:/dev/urandom 512
#SSLRandomSeed connect file:/dev/random 512
SSLRandomSeed connect file:/dev/urandom 512
# When we also provide SSL we have to listen to the
# standard HTTP port (see above) and to the HTTPS port
Listen 443
## SSL Global Context
## All SSL configuration in this context applies both to
## the main server and all SSL-enabled virtual hosts.
# SSL Cipher Suite:
# List the ciphers that the client is permitted to negotiate.
# See the mod_ssl documentation for a complete list.
SSLCipherSuite HIGH:MEDIUM:!aNULL:!MD5
# Speed-optimized SSL Cipher configuration:
# If speed is your main concern (on busy HTTPS servers e.g.),
# you might want to force clients to specific, performance
# optimized ciphers. In this case, prepend those ciphers
# to the SSLCipherSuite list, and enable SSLHonorCipherOrder.
# Caveat: by giving precedence to RC4-SHA and AES128-SHA
# (as in the example below), most connections will no longer
# have perfect forward secrecy - if the server's key is
# compromised, captures of past or future traffic must be
# considered compromised, too.
#SSLCipherSuite RC4-SHA:AES128-SHA:HIGH:MEDIUM:!aNULL:!MD5
#SSLHonorCipherOrder on
# Pass Phrase Dialog:
# Configure the pass phrase gathering process.
# The filtering dialog program (`builtin' is an internal
# terminal dialog) has to provide the pass phrase on stdout.
SSLPassPhraseDialog builtin
# Inter-Process Session Cache:
# Configure the SSL Session Cache: First the mechanism
# to use and second the expiring timeout (in seconds).
#SSLSessionCache "dbm:/run/httpd/ssl_scache"
SSLSessionCache "shmcb:/run/httpd/ssl_scache(512000)"
SSLSessionCacheTimeout 6000
## SSL Virtual Host Context
<VirtualHost _default_:443>
# General setup for the virtual host
DocumentRoot "/mnt/sda1/svn"
ServerName 192.168.178.48:443
ServerAdmin [email protected]
ErrorLog "/var/log/httpd/error_log"
TransferLog "/var/log/httpd/access_log"
# SSL Engine Switch:
# Enable/Disable SSL for this virtual host.
SSLEngine on
# Server Certificate:
# Point SSLCertificateFile at a PEM encoded certificate. If
# the certificate is encrypted, then you will be prompted for a
# pass phrase. Note that a kill -HUP will prompt again. Keep
# in mind that if you have both an RSA and a DSA certificate you
# can configure both in parallel (to also allow the use of DSA
# ciphers, etc.)
# Some ECC cipher suites (http://www.ietf.org/rfc/rfc4492.txt)
# require an ECC certificate which can also be configured in
# parallel.
SSLCertificateFile "/etc/httpd/conf/server.crt"
#SSLCertificateFile "/etc/httpd/conf/server-dsa.crt"
#SSLCertificateFile "/etc/httpd/conf/server-ecc.crt"
# Server Private Key:
# If the key is not combined with the certificate, use this
# directive to point at the key file. Keep in mind that if
# you've both a RSA and a DSA private key you can configure
# both in parallel (to also allow the use of DSA ciphers, etc.)
# ECC keys, when in use, can also be configured in parallel
SSLCertificateKeyFile "/etc/httpd/conf/server.key"
#SSLCertificateKeyFile "/etc/httpd/conf/server-dsa.key"
#SSLCertificateKeyFile "/etc/httpd/conf/server-ecc.key"
# Server Certificate Chain:
# Point SSLCertificateChainFile at a file containing the
# concatenation of PEM encoded CA certificates which form the
# certificate chain for the server certificate. Alternatively
# the referenced file can be the same as SSLCertificateFile
# when the CA certificates are directly appended to the server
# certificate for convenience.
#SSLCertificateChainFile "/etc/httpd/conf/server-ca.crt"
# Certificate Authority (CA):
# Set the CA certificate verification path where to find CA
# certificates for client authentication or alternatively one
# huge file containing all of them (file must be PEM encoded)
# Note: Inside SSLCACertificatePath you need hash symlinks
# to point to the certificate files. Use the provided
# Makefile to update the hash symlinks after changes.
#SSLCACertificatePath "/etc/httpd/conf/ssl.crt"
#SSLCACertificateFile "/etc/httpd/conf/ssl.crt/ca-bundle.crt"
# Certificate Revocation Lists (CRL):
# Set the CA revocation path where to find CA CRLs for client
# authentication or alternatively one huge file containing all
# of them (file must be PEM encoded).
# The CRL checking mode needs to be configured explicitly
# through SSLCARevocationCheck (defaults to "none" otherwise).
# Note: Inside SSLCARevocationPath you need hash symlinks
# to point to the certificate files. Use the provided
# Makefile to update the hash symlinks after changes.
#SSLCARevocationPath "/etc/httpd/conf/ssl.crl"
#SSLCARevocationFile "/etc/httpd/conf/ssl.crl/ca-bundle.crl"
#SSLCARevocationCheck chain
# Client Authentication (Type):
# Client certificate verification type and depth. Types are
# none, optional, require and optional_no_ca. Depth is a
# number which specifies how deeply to verify the certificate
# issuer chain before deciding the certificate is not valid.
#SSLVerifyClient require
#SSLVerifyDepth 10
# TLS-SRP mutual authentication:
# Enable TLS-SRP and set the path to the OpenSSL SRP verifier
# file (containing login information for SRP user accounts).
# Requires OpenSSL 1.0.1 or newer. See the mod_ssl FAQ for
# detailed instructions on creating this file. Example:
# "openssl srp -srpvfile /etc/httpd/conf/passwd.srpv -add username"
#SSLSRPVerifierFile "/etc/httpd/conf/passwd.srpv"
# Access Control:
# With SSLRequire you can do per-directory access control based
# on arbitrary complex boolean expressions containing server
# variable checks and other lookup directives. The syntax is a
# mixture between C and Perl. See the mod_ssl documentation
# for more details.
#<Location />
#SSLRequire ( %{SSL_CIPHER} !~ m/^(EXP|NULL)/ \
# and %{SSL_CLIENT_S_DN_O} eq "Snake Oil, Ltd." \
# and %{SSL_CLIENT_S_DN_OU} in {"Staff", "CA", "Dev"} \
# and %{TIME_WDAY} >= 1 and %{TIME_WDAY} <= 5 \
# and %{TIME_HOUR} >= 8 and %{TIME_HOUR} <= 20 ) \
# or %{REMOTE_ADDR} =~ m/^192\.76\.162\.[0-9]+$/
#</Location>
# SSL Engine Options:
# Set various options for the SSL engine.
# o FakeBasicAuth:
# Translate the client X.509 into a Basic Authorisation. This means that
# the standard Auth/DBMAuth methods can be used for access control. The
# user name is the `one line' version of the client's X.509 certificate.
# Note that no password is obtained from the user. Every entry in the user
# file needs this password: `xxj31ZMTZzkVA'.
# o ExportCertData:
# This exports two additional environment variables: SSL_CLIENT_CERT and
# SSL_SERVER_CERT. These contain the PEM-encoded certificates of the
# server (always existing) and the client (only existing when client
# authentication is used). This can be used to import the certificates
# into CGI scripts.
# o StdEnvVars:
# This exports the standard SSL/TLS related `SSL_*' environment variables.
# Per default this exportation is switched off for performance reasons,
# because the extraction step is an expensive operation and is usually
# useless for serving static content. So one usually enables the
# exportation for CGI and SSI requests only.
# o StrictRequire:
# This denies access when "SSLRequireSSL" or "SSLRequire" applied even
# under a "Satisfy any" situation, i.e. when it applies access is denied
# and no other module can change it.
# o OptRenegotiate:
# This enables optimized SSL connection renegotiation handling when SSL
# directives are used in per-directory context.
#SSLOptions +FakeBasicAuth +ExportCertData +StrictRequire
<FilesMatch "\.(cgi|shtml|phtml|php)$">
SSLOptions +StdEnvVars
</FilesMatch>
<Directory "/srv/http/cgi-bin">
SSLOptions +StdEnvVars
</Directory>
# SSL Protocol Adjustments:
# The safe and default but still SSL/TLS standard compliant shutdown
# approach is that mod_ssl sends the close notify alert but doesn't wait for
# the close notify alert from client. When you need a different shutdown
# approach you can use one of the following variables:
# o ssl-unclean-shutdown:
# This forces an unclean shutdown when the connection is closed, i.e. no
# SSL close notify alert is sent or allowed to be received. This violates
# the SSL/TLS standard but is needed for some brain-dead browsers. Use
# this when you receive I/O errors because of the standard approach where
# mod_ssl sends the close notify alert.
# o ssl-accurate-shutdown:
# This forces an accurate shutdown when the connection is closed, i.e. a
# SSL close notify alert is send and mod_ssl waits for the close notify
# alert of the client. This is 100% SSL/TLS standard compliant, but in
# practice often causes hanging connections with brain-dead browsers. Use
# this only for browsers where you know that their SSL implementation
# works correctly.
# Notice: Most problems of broken clients are also related to the HTTP
# keep-alive facility, so you usually additionally want to disable
# keep-alive for those clients, too. Use variable "nokeepalive" for this.
# Similarly, one has to force some clients to use HTTP/1.0 to workaround
# their broken HTTP/1.1 implementation. Use variables "downgrade-1.0" and
# "force-response-1.0" for this.
BrowserMatch "MSIE [2-5]" \
nokeepalive ssl-unclean-shutdown \
downgrade-1.0 force-response-1.0
# Per-Server Logging:
# The home of a custom SSL log file. Use this when you want a
# compact non-error SSL logfile on a virtual host basis.
CustomLog "/var/log/httpd/ssl_request_log" \
"%t %h %{SSL_PROTOCOL}x %{SSL_CIPHER}x \"%r\" %b"
#SSLSessionTimeout 5m
Timeout 600000
<Location />
DAV svn
SVNParentPath /mnt/sda1/svn/repos
AuthzSVNAccessFile /home/svn/.svn-policy-file
AuthName "SVN Repositories"
AuthType Basic
AuthUserFile /home/svn/.svn-auth-file
# Satisfy Any
Require valid-user
</Location>
</VirtualHost>
httpd.conf
# This is the main Apache HTTP server configuration file. It contains the
# configuration directives that give the server its instructions.
# See <URL:http://httpd.apache.org/docs/2.4/> for detailed information.
# In particular, see
# <URL:http://httpd.apache.org/docs/2.4/mod/directives.html>
# for a discussion of each configuration directive.
# Do NOT simply read the instructions in here without understanding
# what they do. They're here only as hints or reminders. If you are unsure
# consult the online docs. You have been warned.
# Configuration and logfile names: If the filenames you specify for many
# of the server's control files begin with "/" (or "drive:/" for Win32), the
# server will use that explicit path. If the filenames do *not* begin
# with "/", the value of ServerRoot is prepended -- so "logs/access_log"
# with ServerRoot set to "/usr/local/apache2" will be interpreted by the
# server as "/usr/local/apache2/logs/access_log", whereas "/logs/access_log"
# will be interpreted as '/logs/access_log'.
# ServerRoot: The top of the directory tree under which the server's
# configuration, error, and log files are kept.
# Do not add a slash at the end of the directory path. If you point
# ServerRoot at a non-local disk, be sure to specify a local disk on the
# Mutex directive, if file-based mutexes are used. If you wish to share the
# same ServerRoot for multiple httpd daemons, you will need to change at
# least PidFile.
ServerRoot "/etc/httpd"
Timeout 60000
# Mutex: Allows you to set the mutex mechanism and mutex file directory
# for individual mutexes, or change the global defaults
# Uncomment and change the directory if mutexes are file-based and the default
# mutex file directory is not on a local disk or is not appropriate for some
# other reason.
# Mutex default:/run/httpd
# Listen: Allows you to bind Apache to specific IP addresses and/or
# ports, instead of the default. See also the <VirtualHost>
# directive.
# Change this to Listen on specific IP addresses as shown below to
# prevent Apache from glomming onto all bound IP addresses.
#Listen 12.34.56.78:80
Listen 80
# Dynamic Shared Object (DSO) Support
# To be able to use the functionality of a module which was built as a DSO you
# have to place corresponding `LoadModule' lines at this location so the
# directives contained in it are actually available _before_ they are used.
# Statically compiled modules (those listed by `httpd -l') do not need
# to be loaded here.
# Example:
# LoadModule foo_module modules/mod_foo.so
LoadModule authn_file_module modules/mod_authn_file.so
#LoadModule authn_dbm_module modules/mod_authn_dbm.so
#LoadModule authn_anon_module modules/mod_authn_anon.so
#LoadModule authn_dbd_module modules/mod_authn_dbd.so
#nach fehlermeldung
LoadModule authn_socache_module modules/mod_authn_socache.so
LoadModule authn_core_module modules/mod_authn_core.so
LoadModule authz_host_module modules/mod_authz_host.so
LoadModule authz_groupfile_module modules/mod_authz_groupfile.so
LoadModule authz_user_module modules/mod_authz_user.so
#LoadModule authz_dbm_module modules/mod_authz_dbm.so
#LoadModule authz_owner_module modules/mod_authz_owner.so
#LoadModule authz_dbd_module modules/mod_authz_dbd.so
LoadModule authz_core_module modules/mod_authz_core.so
#LoadModule authnz_ldap_module modules/mod_authnz_ldap.so
LoadModule access_compat_module modules/mod_access_compat.so
LoadModule auth_basic_module modules/mod_auth_basic.so
#LoadModule auth_form_module modules/mod_auth_form.so
#LoadModule auth_digest_module modules/mod_auth_digest.so
#LoadModule allowmethods_module modules/mod_allowmethods.so
#LoadModule file_cache_module modules/mod_file_cache.so
#Felhermeldung undefined symbols
LoadModule cache_module modules/mod_cache.so
#LoadModule cache_disk_module modules/mod_cache_disk.so
#nach Fehlermeldung
LoadModule cache_socache_module modules/mod_cache_socache.so
#nochne Fehlermeldung
LoadModule socache_shmcb_module modules/mod_socache_shmcb.so
#LoadModule socache_dbm_module modules/mod_socache_dbm.so
#LoadModule socache_memcache_module modules/mod_socache_memcache.so
#LoadModule watchdog_module modules/mod_watchdog.so
#LoadModule macro_module modules/mod_macro.so
#LoadModule dbd_module modules/mod_dbd.so
#LoadModule dumpio_module modules/mod_dumpio.so
#LoadModule echo_module modules/mod_echo.so
#LoadModule buffer_module modules/mod_buffer.so
#LoadModule data_module modules/mod_data.so
#LoadModule ratelimit_module modules/mod_ratelimit.so
LoadModule reqtimeout_module modules/mod_reqtimeout.so
#LoadModule ext_filter_module modules/mod_ext_filter.so
#LoadModule request_module modules/mod_request.so
LoadModule include_module modules/mod_include.so
LoadModule filter_module modules/mod_filter.so
#LoadModule reflector_module modules/mod_reflector.so
#LoadModule substitute_module modules/mod_substitute.so
#LoadModule sed_module modules/mod_sed.so
#LoadModule charset_lite_module modules/mod_charset_lite.so
#LoadModule deflate_module modules/mod_deflate.so
#LoadModule xml2enc_module modules/mod_xml2enc.so
#LoadModule proxy_html_module modules/mod_proxy_html.so
LoadModule mime_module modules/mod_mime.so
#LoadModule ldap_module modules/mod_ldap.so
LoadModule log_config_module modules/mod_log_config.so
#LoadModule log_debug_module modules/mod_log_debug.so
#LoadModule log_forensic_module modules/mod_log_forensic.so
#LoadModule logio_module modules/mod_logio.so
#LoadModule lua_module modules/mod_lua.so
LoadModule env_module modules/mod_env.so
#LoadModule mime_magic_module modules/mod_mime_magic.so
#LoadModule cern_meta_module modules/mod_cern_meta.so
#LoadModule expires_module modules/mod_expires.so
LoadModule headers_module modules/mod_headers.so
#LoadModule ident_module modules/mod_ident.so
#LoadModule usertrack_module modules/mod_usertrack.so
#LoadModule unique_id_module modules/mod_unique_id.so
LoadModule setenvif_module modules/mod_setenvif.so
LoadModule version_module modules/mod_version.so
#LoadModule remoteip_module modules/mod_remoteip.so
LoadModule proxy_module modules/mod_proxy.so
LoadModule proxy_connect_module modules/mod_proxy_connect.so
LoadModule proxy_ftp_module modules/mod_proxy_ftp.so
LoadModule proxy_http_module modules/mod_proxy_http.so
LoadModule proxy_fcgi_module modules/mod_proxy_fcgi.so
LoadModule proxy_scgi_module modules/mod_proxy_scgi.so
#LoadModule proxy_fdpass_module modules/mod_proxy_fdpass.so
LoadModule proxy_wstunnel_module modules/mod_proxy_wstunnel.so
LoadModule proxy_ajp_module modules/mod_proxy_ajp.so
LoadModule proxy_balancer_module modules/mod_proxy_balancer.so
LoadModule proxy_express_module modules/mod_proxy_express.so
#LoadModule session_module modules/mod_session.so
#LoadModule session_cookie_module modules/mod_session_cookie.so
#LoadModule session_crypto_module modules/mod_session_crypto.so
#LoadModule session_dbd_module modules/mod_session_dbd.so
LoadModule slotmem_shm_module modules/mod_slotmem_shm.so
#LoadModule slotmem_plain_module modules/mod_slotmem_plain.so
#Fuer die cipher suite
LoadModule ssl_module modules/mod_ssl.so
#LoadModule dialup_module modules/mod_dialup.so
LoadModule lbmethod_byrequests_module modules/mod_lbmethod_byrequests.so
LoadModule lbmethod_bytraffic_module modules/mod_lbmethod_bytraffic.so
LoadModule lbmethod_bybusyness_module modules/mod_lbmethod_bybusyness.so
LoadModule lbmethod_heartbeat_module modules/mod_lbmethod_heartbeat.so
LoadModule mpm_event_module modules/mod_mpm_event.so
LoadModule unixd_module modules/mod_unixd.so
#LoadModule heartbeat_module modules/mod_heartbeat.so
#LoadModule heartmonitor_module modules/mod_heartmonitor.so
#1 for svn
LoadModule dav_module modules/mod_dav.so
LoadModule status_module modules/mod_status.so
LoadModule autoindex_module modules/mod_autoindex.so
#LoadModule asis_module modules/mod_asis.so
#LoadModule info_module modules/mod_info.so
#LoadModule suexec_module modules/mod_suexec.so
#LoadModule cgid_module modules/mod_cgid.so
#LoadModule cgi_module modules/mod_cgi.so
#2 for svn
LoadModule dav_fs_module modules/mod_dav_fs.so
#LoadModule dav_lock_module modules/mod_dav_lock.so
#LoadModule vhost_alias_module modules/mod_vhost_alias.so
LoadModule negotiation_module modules/mod_negotiation.so
LoadModule dir_module modules/mod_dir.so
#LoadModule imagemap_module modules/mod_imagemap.so
#LoadModule actions_module modules/mod_actions.so
#LoadModule speling_module modules/mod_speling.so
LoadModule userdir_module modules/mod_userdir.so
LoadModule alias_module modules/mod_alias.so
#LoadModule rewrite_module modules/mod_rewrite.so
#3 for svn
LoadModule dav_svn_module modules/mod_dav_svn.so
LoadModule authz_svn_module modules/mod_authz_svn.so
<IfModule unixd_module>
# If you wish httpd to run as a different user or group, you must run
# httpd as root initially and it will switch.
# User/Group: The name (or #number) of the user/group to run httpd as.
# It is usually good practice to create a dedicated user and group for
# running httpd, as with most system services.
User http
Group http
</IfModule>
# 'Main' server configuration
# The directives in this section set up the values used by the 'main'
# server, which responds to any requests that aren't handled by a
# <VirtualHost> definition. These values also provide defaults for
# any <VirtualHost> containers you may define later in the file.
# All of these directives may appear inside <VirtualHost> containers,
# in which case these default settings will be overridden for the
# virtual host being defined.
# ServerAdmin: Your address, where problems with the server should be
# e-mailed. This address appears on some server-generated pages, such
# as error documents. e.g. [email protected]
ServerAdmin [email protected]
# ServerName gives the name and port that the server uses to identify itself.
# This can often be determined automatically, but we recommend you specify
# it explicitly to prevent problems during startup.
# If your host doesn't have a registered DNS name, enter its IP address here.
#ServerName www.example.com:80
# Deny access to the entirety of your server's filesystem. You must
# explicitly permit access to web content directories in other
# <Directory> blocks below.
<Directory />
AllowOverride none
Require all denied
</Directory>
# Note that from this point forward you must specifically allow
# particular features to be enabled - so if something's not working as
# you might expect, make sure that you have specifically enabled it
# below.
# DocumentRoot: The directory out of which you will serve your
# documents. By default, all requests are taken from this directory, but
# symbolic links and aliases may be used to point to other locations.
DocumentRoot "/mnt/sda1"
#<Directory "/mnt/sda1/svn/repos">
# # Possible values for the Options directive are "None", "All",
# # or any combination of:
# # Indexes Includes FollowSymLinks SymLinksifOwnerMatch ExecCGI MultiViews
# # Note that "MultiViews" must be named *explicitly* --- "Options All"#
# # doesn't give it to you.
# # The Options directive is both complicated and important. Please see
# # http://httpd.apache.org/docs/2.4/mod/core.html#options
# # for more information.#
# Options Indexes FollowSymLinks
# # AllowOverride controls what directives may be placed in .htaccess files.
# # It can be "All", "None", or any combination of the keywords:
# # AllowOverride FileInfo AuthConfig Limit
# AllowOverride None
# # Controls who can get stuff from this server.
# Require all granted
#</Directory>
# DirectoryIndex: sets the file that Apache will serve if a directory
# is requested.
<IfModule dir_module>
DirectoryIndex index.html
</IfModule>
# The following lines prevent .htaccess and .htpasswd files from being
# viewed by Web clients.
<Files ".ht*">
Require all denied
</Files>
# ErrorLog: The location of the error log file.
# If you do not specify an ErrorLog directive within a <VirtualHost>
# container, error messages relating to that virtual host will be
# logged here. If you *do* define an error logfile for a <VirtualHost>
# container, that host's errors will be logged there and not here.
ErrorLog "/var/log/httpd/error_log"
# LogLevel: Control the number of messages logged to the error_log.
# Possible values include: debug, info, notice, warn, error, crit,
# alert, emerg.
LogLevel warn
<IfModule log_config_module>
# The following directives define some format nicknames for use with
# a CustomLog directive (see below).
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined
LogFormat "%h %l %u %t \"%r\" %>s %b" common
<IfModule logio_module>
# You need to enable mod_logio.c to use %I and %O
LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio
</IfModule>
# The location and format of the access logfile (Common Logfile Format).
# If you do not define any access logfiles within a <VirtualHost>
# container, they will be logged here. Contrariwise, if you *do*
# define per-<VirtualHost> access logfiles, transactions will be
# logged therein and *not* in this file.
CustomLog "/var/log/httpd/access_log" common
# If you prefer a logfile with access, agent, and referer information
# (Combined Logfile Format) you can use the following directive.
#CustomLog "/var/log/httpd/access_log" combined
</IfModule>
<IfModule alias_module>
# Redirect: Allows you to tell clients about documents that used to
# exist in your server's namespace, but do not anymore. The client
# will make a new request for the document at its new location.
# Example:
# Redirect permanent /foo http://www.example.com/bar
# Alias: Maps web paths into filesystem paths and is used to
# access content that does not live under the DocumentRoot.
# Example:
# Alias /webpath /full/filesystem/path
# If you include a trailing / on /webpath then the server will
# require it to be present in the URL. You will also likely
# need to provide a <Directory> section to allow access to
# the filesystem path.
# ScriptAlias: This controls which directories contain server scripts.
# ScriptAliases are essentially the same as Aliases, except that
# documents in the target directory are treated as applications and
# run by the server when requested rather than as documents sent to the
# client. The same rules about trailing "/" apply to ScriptAlias
# directives as to Alias.
ScriptAlias /cgi-bin/ "/srv/http/cgi-bin/"
</IfModule>
<IfModule cgid_module>
# ScriptSock: On threaded servers, designate the path to the UNIX
# socket used to communicate with the CGI daemon of mod_cgid.
#Scriptsock cgisock
</IfModule>
# "/srv/http/cgi-bin" should be changed to whatever your ScriptAliased
# CGI directory exists, if you have that configured.
<Directory "/srv/http/cgi-bin">
AllowOverride None
Options None
Require all granted
</Directory>
<IfModule mime_module>
# TypesConfig points to the file containing the list of mappings from
# filename extension to MIME-type.
TypesConfig conf/mime.types
# AddType allows you to add to or override the MIME configuration
# file specified in TypesConfig for specific file types.
#AddType application/x-gzip .tgz
# AddEncoding allows you to have certain browsers uncompress
# information on the fly. Note: Not all browsers support this.
#AddEncoding x-compress .Z
#AddEncoding x-gzip .gz .tgz
# If the AddEncoding directives above are commented-out, then you
# probably should define those extensions to indicate media types:
AddType application/x-compress .Z
AddType application/x-gzip .gz .tgz
# AddHandler allows you to map certain file extensions to "handlers":
# actions unrelated to filetype. These can be either built into the server
# or added with the Action directive (see below)
# To use CGI scripts outside of ScriptAliased directories:
# (You will also need to add "ExecCGI" to the "Options" directive.)
#AddHandler cgi-script .cgi
# For type maps (negotiated resources):
#AddHandler type-map var
# Filters allow you to process content before it is sent to the client.
# To parse .shtml files for server-side includes (SSI):
# (You will also need to add "Includes" to the "Options" directive.)
#AddType text/html .shtml
#AddOutputFilter INCLUDES .shtml
</IfModule>
# The mod_mime_magic module allows the server to use various hints from the
# contents of the file itself to determine its type. The MIMEMagicFile
# directive tells the module where the hint definitions are located.
#MIMEMagicFile conf/magic
# Customizable error responses come in three flavors:
# 1) plain text 2) local redirects 3) external redirects
# Some examples:
#ErrorDocument 500 "The server made a boo boo."
#ErrorDocument 404 /missing.html
#ErrorDocument 404 "/cgi-bin/missing_handler.pl"
#ErrorDocument 402 http://www.example.com/subscription_info.html
# MaxRanges: Maximum number of Ranges in a request before
# returning the entire resource, or one of the special
# values 'default', 'none' or 'unlimited'.
# Default setting is to accept 200 Ranges.
#MaxRanges unlimited
# EnableMMAP and EnableSendfile: On systems that support it,
# memory-mapping or the sendfile syscall may be used to deliver
# files. This usually improves server performance, but must
# be turned off when serving from networked-mounted
# filesystems or if support for these functions is otherwise
# broken on your system.
# Defaults: EnableMMAP On, EnableSendfile Off
#EnableMMAP off
#EnableSendfile on
# Supplemental configuration
# The configuration files in the conf/extra/ directory can be
# included to add extra features or to modify the default configuration of
# the server, or you may simply copy their contents here and change as
# necessary.
# Server-pool management (MPM specific)
Include conf/extra/httpd-mpm.conf
# Multi-language error messages
Include conf/extra/httpd-multilang-errordoc.conf
# Fancy directory listings
Include conf/extra/httpd-autoindex.conf
# Language settings
Include conf/extra/httpd-languages.conf
# User home directories
Include conf/extra/httpd-userdir.conf
# Real-time info on requests and configuration
#Include conf/extra/httpd-info.conf
# Virtual hosts
#Include conf/extra/httpd-vhosts.conf
# Local access to the Apache HTTP Server Manual
#Include conf/extra/httpd-manual.conf
# Distributed authoring and versioning (WebDAV)
#Include conf/extra/httpd-dav.conf
# Various default settings
Include conf/extra/httpd-default.conf
# Configure mod_proxy_html to understand HTML4/XHTML1
<IfModule proxy_html_module>
Include conf/extra/proxy-html.conf
</IfModule>
# Secure (SSL/TLS) connections
Include /etc/httpd/conf/extra/httpd-ssl.conf
# Note: The following must must be present to support
# starting without SSL on platforms with no /dev/random equivalent
# but a statically compiled-in mod_ssl.
<IfModule ssl_module>
SSLRandomSeed startup builtin
SSLRandomSeed connect builtin
</IfModule>
# uncomment out the below to deal with user agents that deliberately
# violate open standards by misusing DNT (DNT *must* be a specific
# end-user choice)
#<IfModule setenvif_module>
#BrowserMatch "MSIE 10.0;" bad_DNT
#</IfModule>
#<IfModule headers_module>
#RequestHeader unset DNT env=bad_DNT
#</IfModule>
Edit: inserted tl;dr
Last edited by arch_on_pi (2014-05-18 21:33:24)

Remember that Arch Arm is a different distribution, but we try to bend the rules and provide limited support for them. This may or may not be unique to Arch Arm, so you might try asking on their forums as well.

ABAP Query Code timeout issue

Hi,
I have a SAP query which was the following code which is causing a timeout issue when running the report, can anyone suggest how I can change the code to make it more efficent?
* This gets the sum of all labour costs on WBSEs.
clear X_COEP_WKGBTR_LAB_W.
if PRPS-OBJNR is not initial.
select sum( WKGBTR ) from COEP
    into X_COEP_WKGBTR_LAB_W
    where
    PERIO = ZPERIODT
    and
    GJAHR = ZYEAR
    and
    KSTAR >= 'A43'
    and
    KSTAR =< 'A43ZZZZZZZ'
    OR
     KSTAR = '0005767012'
    and
    OBJNR = PRPS-OBJNR.
endif.
thanks
Joe

Hi Joe,
I see none of the Key fields were used in select query.
Create a secondary index for the table and use it in select query.
It increases the performance.
COEP~1 and COEP~2 are already existing.
select sum( WKGBTR ) from COEP
    into X_COEP_WKGBTR_LAB_W
    where
    PERIO = ZPERIODT
    and
    GJAHR = ZYEAR
    and
    KSTAR >= 'A43'
    and
    KSTAR =< 'A43ZZZZZZZ'
    OR
     KSTAR = '0005767012'
    and
    OBJNR = PRPS-OBJNR
%_HINTS ORACLE 'INDEX("COEP" "COEP~1").
Thanks,
Anil

High RFC response time in SAP BW system

Hello all,
How to analyze and fine tune high RFC response time in SAP BW system ?
Regards,
Archana

Hi
Kindly Check follows
1. Check the RFC connections are correctly Configured or not? You can execute the program “RSRFCTRC” and get a full log of the RFC connections details
2 you can check the BW queries are right optimized? Is this any network issues?
3. In which time are you facing the high rfc response? (During the 24 hours which time)?
4. Kindly refer the SCN & SAP Notes for overall system performance
Short Notes on PERFORMANCE MONITORING - ABAP Development - SCN Wiki
1063061 - Information about response time in STAD/ST03
948066 - Performance Analysis: Transactions to use
Regards
Sriram

Issue in SAP CPS for Job Interception

Issue in SAP CPS for Job Interception
Scenario:
After triggering a Process Chain in BW and maintaining the Job Interception settings in SAPCPS(Redwood)
(so that any job which triggers in BW by that Particular User is intercepted and not let it proceed further until the job is released in SAP CPS.)
Issue:
The Jobs are getting into Waiting status in SAP CPS(Redwood) even though there is no progress in loads in BW side. Also the Jobs are in Intercepted state even after releasing the Parent Job in SAP CPS(Redwood).
Please let us know how to go about it.

Hi Ramesh,
What you plan to do is called monitoring of process chains (ie. process chains not started from CPS) and this should be available in the latest version of CPS.
This requires the interception of only the BI_PROCESS_TRIGGER process, just as you have configured now, and other than that the following prerequisites:
SAP Note 1080558 describes the SP levels for the BW/BI releases
XBP 2.0 or higher
Redwood transport files must be loaded
ProcessServerService.SAP.XBPVariant license key
Maybe this helps,
Anton.

Performance issues with SAP BPC 7.0/7.5 (SP06, 07, 08) NW

Hi Experts
There are some performance issues with SAP BPC 7.5/7.0 NW, users are saying they are not getting data or there are some issues while getting data from R/3 system or ECC 6.0. Then what things do I need to consider to check, such as what DataSources or Cubes I need to check? So, how to solve this issue?
What things I need to consider for SAP NW BI 7.0 u2013 SAP BPC 7.5 NW (SP06, 07, 08) Implementation?
Your help is greatly appreciated.
Regards,
Qadeer

Hi,
New SP was released in February, and now most of the new bugs should been caught ,This has a Central Note. For SP06 it's Note 1527325 - Planning and Consolidation 7.5 SP06 NetWeaver Central Note to fix any issues. Most of the improvements in SP06 were related to performance, especially when logging on from the BPC clients.There you should be able to find a big list of fixes/improvements and Notes that describe those. Some of the Notes even have test description how to reproduce that issue in the old version.
hope this will help you
Regards
Rv

SSRS Timeout issue

I am using SSRS for generate reports in my .net web application. For one of the report, an error "An error has occurred during report processing." is returned after 100s. The report can be generated successfully in report server
at around 3 minutes. So, I believed it is caused by timeout issue in one of the processes. However, i have verified the timeout settings but still got no ideas on how to fix it.
My code is a bit complicated since the connection type of my report's data source is an customized dll. In the dll, i will call an webservice to get data. Below is summary for the flow:
UI -> Reporting Service -> Customized Dll -> Web service -> SQL/Stored Procedures
The execution timeount in the web.config of both the reporting service and web service are set to 9000s (<httpRuntime executionTimeout = "9000" />). And coding about timeout of the service is set to 3000s (i.e. ReportingService rs = new ReportingService();
rs.timeout = 3000000;). In the execution properties of the report, Report Execution Time is set to "Do not timeout report execution" currently.
I think there is no problem for the customized dll and the web service it calls since it can be generated in report server direclty. But I have no idea about where the timeout occurs. Please kindly help.
Thanks,
Shirley

Hi Shirley,
According to your description, you encountered time out issue when rendering your report in your web application. Right?
In Reporting Services, we have report execution timeout value and query timeout value for processing report and dataset. In this scenario, you have already set the report executionTimeout and "Do not timeout report execution" on report level. Since
this time issue only happens on specific report, it probably cause by processing large amount of data which exceeds the max query timeout. Please go to rsreportserver.config file and change the QueryTimeOut into "0". This file locates at
xx:\Program Files\Microsoft SQL Server\MSRS12.MSSQLSERVER\Reporting Services\ReportServer
<Add Key="DatabaseQueryTimeout" Value="0"/>
Reference:
Setting Time-out Values for Report and Shared Dataset Processing (SSRS)
Troubleshooting Timeout errors in Reporting Services
If you have any question, please feel free to ask.
Best Regards,
Simon Hou

Call a RFC or BAPI in SAP R/3

Hi,
Please give your replies.
I written a RFC function module in SAPR/3 , my requirement is that RFC to be called from SAPXI.
This RFC will update some SAP transactions and return back the document number back
Whether it is possible?
aRs

Hai,
<i>my requirement is that RFC to be called from SAPXI.</i>
at design time you have to import RFC module into imported bjects
Select Message Interface as Synchronous Type
and do rest of the things like mapping...
At configuration
Under communication channel select adapter type as RFC adapter and receiver.
and pass the SAP R/3 details
thanks & regards
harsha
*********Reward points if found useful*********

RFC Timeout

Hi,
I have a scenario HTTP> XI> RFC
It is synchronos scenario.
There can be HTTP timeout or RFC timeout.
HTTP Timeout will return HTTP Error 500.
In case of RFC timeout in XI I want to send timeout error in Response.
Is this possible without BPM (I know I can catch system exception in block )
Thanks in advance.
Beena.

Hi Aamir,
I dont want to send alert but my JSP page should receive xml Response with \
<Error>Timeout<Error>
Thanks,
Beena

RFC Import from own SAP XI results in java.lang.NullPointerException

Hi All,
I'm trying to do an import of a local RFC (developed in SAP XI) but this results in a java.lang.NullPointerException
RFC import from other SAP system is no problem.
Anyone an idea?
Cheers,
Frank

Hi,
But we are using custom RFCs from SAP XI only. We are using XI3.0 SP11.
Could you pls check the following sap notes..
SAP Notes 677732, 672745, 212011, and 718320.
Have a look at the following link...
http://help.sap.com/saphelp_nw04/helpdata/en/2b/a48f3c685bc358e10000000a11405a/frameset.htm
Thanks,
Sasi

Critical Issues During SAP Implementation or After Golive

Can anybody tell me one of the most critical/ challenging issues During SAP Implementation or After Golive
in these modules:-
MM implementation
PP implementation
SD implementation
FI/CO implementation
PS implementation
QM implementation
HR implementation
BI implementation
XI implementation
Thanks and regards
RS

hi,
I will list out few of critical issues in
Implementation :
1 . Ensure 100% mapping of business process for all modules with SAP(avoid customization in support phase)
2. Unit & Integeration testing should be through with all validations
3. Master datas(Vendor,Customer) care must be taken will uploading datas thru LSMW,
If there are common vendors for all plants,Create a vendor for a plant extend it to other plants
4. Check tax procedures are customized according to requirements.
5. Complete all print document customizations before go live
6. Complete end user training(2 or more cycles) should be top priority before go live(This will avoid
cancellation/reversal of documents after post go live)
7. Ready with standard MIS reports & customized reports for business decision making
8. Excise opening balance updation in tables for RG1 register in tables(Note 951955) on go live
9. Check all tables datas are updating correctly
10. Declare go live to SAP Support
11. Check All user authorization should be correct according to their roles.
12. Centeralize all master datas creation(avoid duplication)
13. Create transaction variants to avoid entires in unnecessary fields & make certain fields mandatory.
14. Ensure document numbering is completed for all documents
15. Validate accounting entries are hit properly according to requirement in quality client with FI CTM(Core team member).
After Go live :
1. Missing authorization for users will play key part here,For ex : PGI while doing delivery,Excise capture & post in MIGO/J1IEX.
2. Do internal audit every month,identify transactions if there will possibility for misuse or wrong entries,requires validation,identify users weak in certain areas.
3. Identify there is enhancements to be done in transaction process(By step-2)
4. Prepare a list of month & year end activities to be performed for all modules give to users
5. Prepare a list of frequently used transaction codes module wise give it to users
6. If there is subcontracting,ensure challan creation,GR,reconcillation should be done regulary(monthly)
7. Train the users,take reports in respective modules.
8. Additonal customization might be done in print documents.
9. Instruct users/CTM's to adapt SAP Standard practise
10. Update excise tax rates after every indian budget
Hope it helps.
Edited by: Jeyakanthan A on Apr 29, 2010 6:48 PM

How to check which RFCs causing issues in the system and RFC response times

Hi,
We have an issue with the RFC response times in CRM and need investigstion. We need to know which Which RFCs causing issues and how we can solve the problems.
Regards

Hi,
chek the below code
CALL METHOD CL_GUI_FRONTEND_SERVICES=>FILE_EXIST
EXPORTING
FILE = W_FILENAME
RECEIVING
RESULT = W_RESULT
EXCEPTIONS
CNTL_ERROR = 1
ERROR_NO_GUI = 2
WRONG_PARAMETER = 3
NOT_SUPPORTED_BY_GUI = 4
others = 5.
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-* MSGNO WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
IF W_RESULT IS INITIAL.
CALL METHOD CL_GUI_FRONTEND_SERVICES=>DIRECTORY_EXIST
EXPORTING
DIRECTORY = W_FILENAME
RECEIVING
RESULT = W_RESULT
EXCEPTIONS
CNTL_ERROR = 1
ERROR_NO_GUI = 2
WRONG_PARAMETER = 3
NOT_SUPPORTED_BY_GUI = 4
OTHERS = 5.
IF SY-SUBRC <> 0.
ENDIF.
ENDIF.
IF W_RESULT = 'X'.
RC = '1'.
ELSE.
RC = '0'.
ENDIF.
reward if helpful.
Regards,
nagaraj

MDDataSetBW.GetCellData. See RFC trace file or SAP system log for more...

Ingo,
I am getting below error message in BO Test environment when I refresh WebI document.
MDDataSetBW.GetCellData. See RFC trace file or SAP system log for more details
It was working when we migrated the objects initially. Subsequently when we try to refresh WebI document we are getting the above error message. It still works in BO Dev environment and the no of records are the same in Dev and Test.
I am able run the underlying BEx query in SAP BW Test environment and it does return data.
I checked ST22 and SM21 log, but no details there.
Is it related to Authorization on the Universe or Bex Query?
We are in the middle of UAT and not able to move forward. I would greatly appreciate your input.
Thanks
Ram

Ingo,
I ran the zip file and added the required entries to registry.
And then I tried to reproduce the error, but the files are not generated instead I noticeed below error message on the server:
The description for Event ID ( 7939 ) in Source ( Crystal OLAP Client ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. You may be able to use the /AUXSOURCE= flag to retrieve this description; see Help and Support for details. The following information is part of the event: Registry Access Error: , [HKEY_LOCAL_MACHINE]Software\Business Objects\Suite 12.0\MDA\Log\Modules: The system cannot find the file specified..
Does tha t mean we do not have permissons to read the registry?
I would greatly appreciate your input.
Thanks in advance.
Ram

Problem in Fetching data using RFC FM from NON SAP system

Hi All,
Need help from experts on data transfer using RFC from a non SAP system/database. I have creasted the destination in sm59.
I have created a function module too which has an import parameter as a query and export parameter as an internal table.
No when i test run this function module it returns some entries. But when I call this FM in a program it throws a dump 'rfc_external_abort' . Here is what the call to FM looks like in my program. Please guide me on this.
Thanks in advance,
Saket.
DATA : lv_query TYPE string,
       it_gddbdata TYPE ZC9_TAB_SOLMAN_XI_RFC.
lv_query = 'SELECT * FROM GDDB.VW_GDDB_PERSONS WHERE LASTNAME = ''''A'''''.
CALL FUNCTION 'Z_C9_SOLMAN_XI_GDDBCON'
DESTINATION 'D39'
EXPORTING
    in_sql_query       = lv_query
IMPORTING
   ET_GDDB_DATA       = it_gddbdata

Hi,
your question..
DATA : lv_query TYPE string,
it_gddbdata TYPE ZC9_TAB_SOLMAN_XI_RFC.
lv_query = 'SELECT * FROM GDDB.VW_GDDB_PERSONS WHERE LASTNAME = ''''A'''''.
CALL FUNCTION 'Z_C9_SOLMAN_XI_GDDBCON'
DESTINATION 'D39'
EXPORTING
in_sql_query = lv_query
IMPORTING
ET_GDDB_DATA = it_gddbdata
you are telling that you are fetching the data from non sap system using RFC function module.. how it is possible..you canot fetch the data from non SAP system using RFC FM alone.. you have to use the concept BAPI.. it will work..
I hope this will help you..
Regards,
Kiran

RFC Timeout issue in SAP

Similar Messages

Maybe you are looking for