RME config archive problem - lms 3.2

just wondering if anyone else has seen this.
about a month or so ago, I grabbed about 6 or 7 patches for our ciscoworks machine, across cm, rme, and cs. (yeah, we were a little behind)
after applying these patches, it seems, all of the 2960s and 4948s are failing the config archive with the following:
cm00139: could not archive config:cause: action: verify that device is managed and credentials are correct. Increase timeout
value if required.
so I've triple checked the credential set applied to these devices, adjusted timeout and retry values, and have gotten nowhere.
Deleting these devices doesn't seem to help, they are rediscovered just fine, but the config archive continues to fail.
Other than maybe trying to reinstall the rme patches (or uninstall) that were recently applied, I'm out of ideas. This is LMS 3.2.1 with
cm 5.2.2
cs 3.3.1
rme 4.3.2
running on windows server 08.
So if anyone may have seen this and/or has any advice, I'd appreciate it. Thanks - chris

ok, so it's been a year and a half since last post. So in addition to the above mentioned archive failures with the 4948s, the 4948s were also showing up in config out of sync summary. The only difference that were showing between running and startup was the ntp clock period.
I did see that the clock period statement was in the exclude list for routers and a bunch of other things, but not for the 4948s. I added this as an exclusion yesterday. Today when I checked, all 4948s are archiving now, and are off the out of sync report. Never would have crossed my mind to check there, but that exclusion seems to have done the trick. Maybe someone else can use this if they're seeing the same thing. - chris

Similar Messages

  • Call manager and rme config archive report

    Hi,
    I know that rme does not support the call manager for config archive. It is clear.
    The RME home page show config archive status for failed devices and there are some devices which are not supported by RME config archive.
    I've set this devices to suspended state in RME but config archiv is trying with this devices also.
    This is a financial costumer and the local Financial supervisory authority would like to see all devices config is saving successfully.
    How can i exclude the call manager and similar devices from config archiv process and status reports?
    Regards,

    Hi,
    I would like to qoute from RME help.
    Working With Suspended Devices
    Suspended device state cannot participate in any RME application flows but all historical data pertaining to the device will continue to be maintained by RME.
    Nevertheless the RME is trying to fetch the config from suspended devices!!!
    What is the truth in this thing?
    Regards,

  • Config archiving problem

    Hi
    am having problem in archiving config from switches in cisco works. am having problem in only 5 switches all others switch configurations archived when I try to do this I found following error.
    TELNET: Failed to establish TELNET connection to 172.25.2.102 - Cause: Authentication failed on device 3 times. PRIMARY-RUNNING config Fetch Operation failed for TFTP. Failed to detect SSH version running on the device. Failed to fetch config using RCP.Connection refused: connect Verify RCP is enabled or not.
    can any one help me to fix this
    Thanks

    Hi
    Thanks for that apparently nearly 200 switches are working only 5 switches we have a problem. please see snmp config below. I have added RW recently it is not taking effect. please see screen shot of working one and not working
    snmp-server community comms RO
    snmp-server community comms RW
    snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
    snmp-server enable traps tty
    snmp-server enable traps fru-ctrl
    snmp-server enable traps entity
    snmp-server enable traps cpu threshold
    snmp-server enable traps vtp
    snmp-server enable traps vlancreate
    snmp-server enable traps vlandelete
    snmp-server enable traps flash insertion removal
    snmp-server enable traps port-security
    snmp-server enable traps envmon fan shutdown supply temperature status
    snmp-server enable traps license
    snmp-server enable traps config-copy
    snmp-server enable traps config
    snmp-server enable traps hsrp
    snmp-server enable traps bridge newroot topologychange
    snmp-server enable traps stpx inconsistency root-inconsistency loop-inconsistency
    snmp-server enable traps syslog
    snmp-server enable traps vlan-membership
    snmp-server host 172.16.25.12 comms
    snmp-server host 172.16.25.13 comms

  • RME config archive collection status failed

    I can use the logon account to telnet/ssh to the device, but why does the log says it could not detect telnet/ssh?
    Cat1-6509   VLAN    RUNNING   Dec 29 2009 19:54:04    Could not detect SSH protocols running on the device TELNET: Failed to establish TELNET connection to 10.172.x.x - Cause: Authentication failed on device 3 times.
    Cat2-6509  PRIMARY  RUNNING  Dec 29 2009 19:53:45  Could not detect SSH protocols running on the device TELNET: Failed to establish TELNET connection to 10.172.x.x - Cause: Authentication failed on device 3 times.
    Any assistance would be greatly appreciated

    RME cannot connect to the device using the credentials in DCR.  Export the credentials from Common Services > Device and Credentials > Device Management, and verify you can connect to the device and become enabled using those credentials.  If you can, then start a sniffer trace filtering on all telnet traffic to the device in question, and run a new sync archive job.  When it fails, post the capture file.

  • Error Message in config Archive in RME in LMS 4.2

                      I got the below error message in the config archive in the LMS 4.2.
    CM0056 Config fetch failed for 10.0.0.10  Cause: CM0204 Could not create DeviceContext for 797 Cause: CM0202 Could not access 10.0.0.10 via SNMP. Action: Check the Read Community string Action: Check if required device packages are available. Action: Check if protocol is supported by device and required device package is installed.
    Switch model type is 3560 and 2960
    Please tell me the reason for this issue.

    Are you usig only TFTP option to archive configuration. Try to use the telnet/ssh. TFTP as a protocol set for config archive.
    Check the Credential verificatio job to see if the crendentials are configured correctly.
    -Thanks

  • Config Archive Failure

    This image shows that I have Telnet, SSH, TFTP and HTTPS configured for  Config Fetch. What am I missing?
    Thanks Joseph!
    I don't know why, but nearly ALL of my Config Archive VLAN is failing. I am  receiving the following:
    TELNET: Failed to establish TELNET connection to xxx.xxx.xxx.xxx - Cause:   Connection refused. Command failed  VLAN Config fetch is not supported using  RCP.   VLAN Config fetch is not supported using TFTP.
    The above switch is using SSH - not Telnet, but it doesn't try???
    The other error is:
    Command failed  Could not detect SSH protocols running on the device     VLAN  Config fetch is not supported using RCP.   VLAN Config fetch is not supported  using TFTP.
    On this one, it should be using Telnet as that is what is supported on this  particular switch.
    I have verified the credentials are set up correctly for both of these.
    Also, this isn't isolated - it's happening on 293 devices. Only 2 are  successful.
    Any help would be GREATLY appreciated! I am running LMS 3.2

    The following is what I see in the logs:
    ],ERROR,[Thread-1926],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchiveForDevice,1355,VLAN RUNNING Config fetch Failed for csw-a1xc-201-004
    [ Fri Oct 08  06:27:18 MDT 2010 ],DEBUG,[Thread-1926],com.cisco.nm.rmeng.dcma.configmanager.ConfigManager,updateArchiveForDevice,1361,Message : Command failedSSH: Failed to establish SSH connection to x.x.x.x -
    Cause: Authentication failed on device 3 times.
    VLAN Config fetch is not supported using TFTP.
    Please ensure that you have the credentials corrected in the DCR under Common Services --> Device and Credentials --> Devices Management --> Select all the devices in question, edit credentials.
    1. Ensure the primary enable username and password is correct and populated.
    2. Ensure you are using the correct SNMP RO/RW community string and must be populated.
    3. Ensure that all firewall rules allow traffic to and from LMS and devices. Check port 69 UDP and high ports number are allowed.
    4. If this is a multi-home system with two nic cards, go to RME ---> Administration --> System Preferences --> RME Device Attribute --> Add Natted RME IP Address
    Afterwards, rerun the device credential verification to test for telnet, ssh, SNMP RO and RW and ensure it passes. Then do a sync archive and let me know the results.

  • Cisco VG248 config archive fails

    I beleive in the past these devices could not be managed bij RME config management, but now it says in the supported device table:
    The following features are supported:
    Network Topology Layer 2 Services
    Fault Management
    Inventory Collection
    Configuration Deploy Protocols: TELNET, SSH, TFTP, RCP
    Configuration Fetch Protocols: TELNET, SSH, TFTP, RCP
    The password and enable pasword are correct and simply work when I try a telnet from the server.
    The gui is not CLI but menu driven.
    RME just says:
    TELNET: Failed to establish TELNET connection to 10.1.1.7 - Cause: Authentication failed on device 3 times. PRIMARY-RUNNING config Fetch Operation failed for TFTP. Could not detect SSH protocols running on the device.
    What can be wrong?
    Cheers,
    Michel

    Hi Michel,
    Thanks for the screenshot. I found that you now have customized prompts in tacacspropmt.ini file.
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : Username: *
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : username: *
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : login: *
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : Username:*
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : username:*
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : login:*
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : username:*
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for user prompt : Username:*
    [ Fri Aug 26  11:30:26 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Checking for password prompt : Password: *
    and look like RME is able to login to device as well now :-
    [ Fri Aug 26  11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,State traversal for telnet login:
    [ Fri Aug 26  11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Connected
    [ Fri Aug 26  11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Verify
    [ Fri Aug 26  11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,Success
    [ Fri Aug 26  11:29:11 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.transport.cmdsvc.LogAdapter,debug,31,login succeeded
    Kindly run the credentials verification job and let me know the results --> Is the device still failing for the telnet and enable password ?
    Also navigate to CSCOpx\objects\cmf\data and uncomment the following on file cmdsvc.properties like this :-
    InitialTransportTimeout=50000
    TransportTimeout=90000
    TuneSleepMillis=3000
    DelayAfterConnect=1000
    LMS was not able to login to device successfully yet or it could be timeout issue. After this LMS try to get the config of the device using SNMP and tftp, but look like tftp is blocked in network too, See this :-
    [ Fri Aug 26  11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,170,Initialized SNMP
    [ Fri Aug 26  11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.LibCommon.snmp.ConfigCopyMib,copyFromRunning,119,FileName= 20110826113104185-10.13.192.9.cfg tftpDir =  User =  password =  serverAddr = 10.1.3.156
    [ Fri Aug 26  11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.LibCommon.snmp.ConfigCopyMib,copyFromRunning,130,Cannot create variable binding list com.cisco.nm.lib.snmp.lib.SnmpException: SnmpResponseGenErr on 10.13.192.9 while performing SnmpSet at index = 0
    [ Fri Aug 26  11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,182,Fetch completed
    [ Fri Aug 26  11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,190,PRIMARY-RUNNING config Fetch Operation failed
    [ Fri Aug 26  11:31:04 CEST 2011 ],DEBUG,[Thread-956],com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator,fetchConfig,196,PRIMARY-RUNNING config Fetch Operation failed for TFTP. java.lang.Exception: PRIMARY-RUNNING config Fetch Operation failed for TFTP.
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator.fetchConfig(GenericTftpOperator.java:192)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericTftpOperator.fetchConfig(GenericTftpOperator.java:93)
        at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.SimpleFetchOperation.performOperation(SimpleFetchOperation.java:61)
        at com.cisco.nm.xms.xdi.pkgs.LibDcma.persistor.ConfigOperation.doConfigOperation(ConfigOperation.java:111)
        at com.cisco.nm.xms.xdi.pkgs.SharedDcmaGeneric.transport.GenericConfigOperator.fetchConfig(GenericConfigOperator.java:72)
        at com.cisco.nm.rmeng.dcma.configmanager.ConfigManager.updateArchiveForDevice(ConfigManager.java:1317)
        at com.cisco.nm.rmeng.dcma.configmanager.ConfigManager.performCollection(ConfigManager.java:3307)
        at com.cisco.nm.rmeng.dcma.configmanager.CfgUpdateThread.run(CfgUpdateThread.java:27)
    So, in summary, kindly edit the cmdsvc.properties file and make the changes as I suggested . Also let me know the results of the credentials verification job and run the packet capture while running the credentials verification job.
    Many Thanks,
    Gaganjeet

  • Cisco Prime 2.2 Config Archive get Partial-Success

    Good morning everyone!
    I have a question regarding Cisco Prime Infrastructure 2.2 and Config Archive. Im trying to backup a configuration for an old WS-CBS3020-HPQ blade with IOS version 12.2(58)SE1 and im getting an error under "Fetch vlan" that says :
    Couldn't able to collect VLAN on the device. TFTP server not accessible from device.
    Im not sure what this means? It gets partial-success, but the error message worries me. Im not able to find anything in the logs or by searching for the error code. Anyone have any idea where to look? The credential is correct, i tripple checked :)

    I tried using the "tftp-server flash:" command, but didnt help. Im also seeing this problem with a couple of Cisco 3750x switches.

  • Deploying Config Templates with LMS 4

    Hello,
    i tried to deploy configuration templates with Cisco LMS Template Center, thanks to the 10 Cool LMS Tricks to better manage your network i am able to do it now.
    Just i don't know why, after deploying these templates the configuration is not save to the startup-config.
    another problem i have with the snmp-server location configuration. It seems my template does not support spaces in the textbox.
    Any way to put spaces in the snmp location?
    <parameter name="snmp-location">
    <description>SNMP Server Location</description>
    <html-component>textbox</html-component>
    <default-value></default-value>
    <data-type>string</data-type>
    <mandatory>true</mandatory>
    <isGlobal>false</isGlobal>
    <help-description>snmp-server location</help-description>
    <syntax>
    <min/>
    <max/>
    <pattern/>
    </syntax>
    thanks for your feedback.
    alex

    I filed CSCtr87633 to track the issue with not being able to save the running config to startup.  I had thought this was working, but when I used LMS during CiscoLive!, I had a lot of jobs running, and part of the work involved a Netconfig deployment that also took care of the write mem.
    For the space thing, try this template.

  • Config archive failed for devices no longer on DCR

    RME reported 30 devices failed config archive but this devices are already removed from DCR but RME keep reporting this devices. how I can clean up thiese devices from RME?
    Thanks

    You can contact TAC, and they can give you the procedure to surgically remove these device records from the RME database.

  • CiscoWorks: How to upgrade RME 4.3.0 &LMS 3.2?

    Hi,
    Please tell me the procedure to upgrade from RME 4.3.0 to latest software, I think its RME 4.3.1. Where I can find this software?
    Also tell me the procedure to upgrade from LMS 3.2 to LMS 3.2.1 or other latest software. Where I can find this software?
    Please advice if I upgrade to LMS 3.2.1 then it will get automatically upgrade to LMS 4.3.1 or I have manually upgrade the RME 4.3.0.
    Currently we have purchased license for 10,000 devices RME 4.3.0 & LMS 3.2.
    THANKS

    You should be able to find LMS 3.2.1 (for Windows) here:
    http://www.cisco.com/cisco/software/release.html?mdfid=282635181&flowid=16561&softwareid=280775102&os=Windows&release=3.2.1&relind=AVAILABLE&rellifecycle=&reltype=latest
    If that link doesn't work for you, try navigating the tree as a logged in user down from the support home page (http://www.cisco.com/cisco/web/support/index.html) "Download Software" task via selecting it and then:
    Products
    Network Management and Automation
    Routing and Switching Management
    Network Management Solutions
    CiscoWorks LAN Management Solution 3.2 and earlier
    CiscoWorks Lan Management Solution 3.2
    CiscoWorks LMS Software
    Windows-3.2.1
    You can then download and transfer the dowloaded file onto your CiscoWorks host for local installation.

  • CiscoWorks LMS3.2 device selectability in RME Config Management

    Hello
    All of a sudden we are unable to select individual devices in RME / Config Management, devices appear grayed out, we are able to select the whole device group and run the job but not individual devices. If we go to Device Center we can select individual devices and perform tasks.
    We have tried restarting server (windows) and stopping and starting CW Daemon Manager, not sure what else to look at.
    Thanks in advance.
    carl bagge

    Please try to break the integration with the following procedure:
    CiscoWorks to local login mode (bring down ACS integration)
    1. Stop the daemon manager using:
    On Windows: net stop crmdmgtd
    On Solaris: /etc/init.d/dmgtd stop
    2. Execute the following script:
    On Windows: NMSROOT/bin/perl ResetLoginModule.pl
    On Solaris:/opt/CSCOpx/bin/ResetLoginModule.pl
    3. Start the daemon manager using:
    On Windows: net start crmdmgtd
    On Solaris: /etc/init.d/dmgtd start.
    Note: You must have appropriate privileges on the system
    Windows =  Administrator 
    Solaris = root
    After this check if you are able to perform all the tasks without being integrated with ACS and then integrate again,  but in CW Common Services>Server>Security>AAA Mode Setup, please do not check the Application Registration box.

  • HT1430 Iphone 5 OS 6.1.1, When I turn off or restart device, this device automatic unmute. How can i config this problem?

    Iphone 5 OS 6.1.1, When I turn off or restart device, this device automatic unmute. How can i config this problem?

    Hey everyone in Apple world!
    I figured out how to fix the flashing yellow screen problem that I've been having on my MBP!  Yessssss!!!
    I found this super handy website with the golden answer: http://support.apple.com/kb/HT1379
    I followed the instructions on this page and here's what I did:
    Resetting NVRAM / PRAM
    Shut down your Mac.
    Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
    Turn on the computer.
    Press and hold the Command-Option-P-R keys before the gray screen appears.
    Hold the keys down until the computer restarts and you hear the startup sound for the second time.
    Release the keys.
    I went through the 6 steps above twice, just to make sure I got rid of whatever stuff was holding up my bootup process.  Since I did that, my MBP boots up just like normal.  No flashing yellow screen anymore!!   
    (Note that I arrived at this solution when I first saw this page: http://support.apple.com/kb/TS2570?viewlocale=en_US)
    Let me know if this works for you!
    Elaine

  • Partially Collected Config Archive

    Hello,
    For 3 switches config archive is partially collected,After searching from enough threads i have done the below but still no sucess
    i have given enough rights to tftpboot dir for caususer
    created a vlan.dat in tftpboot folder
    manually copied vlan.dat from switch to the file in vlan.dat
    start a job of syn but no sucess.
    Any hints experts.
    Thanks

    Dear's
    Waiting for ur replies??
    Thanks.

  • 4507R-E and RME Config Change Report

    Hello,
    We have a new 4507R-E Switch which RME keeps reporting as "CONFIG_CHANGE" each evening. When you click to see the change, the only thing that has changes is the "ntp clock-period".
    However, we have configured "ntp clock-period" as an exclude command in RME Config Managment.
    Any idea's for anything else which could be causing this?

    Bump.....We're still having this issue......does anyone have any ideas....

Maybe you are looking for