RME Inventory collection - device sensed, collection failed
Hello, i have this problem with
cisco AP12XX. Some of the AP works fine some not.
I have checked the IOS version on two of them (one working and one not) it is the same version 12.3(7)JA1
Thanks a lot for your help
You are seeing a timeout reading the FLASH-MIB. Increase your SNMP timeout in RME to 10 seconds under RME > Devices > Device Management > RME Devices. Edit the attributes for this AP, then do an inline edit, and change the timeout. Be sure to save then apply the changes on the previous window.
Please support CSC Helps Haiti
https://supportforums.cisco.com/docs/DOC-8895
https://supportforums.cisco.com
Similar Messages
-
Inventorycollection ENTITY_Mib:device sensed but collection failed
Dears,
It appears in LMS 4.2, Inventory Collection, is trying to query some POE MIB or MIB entries that older devices don't support.
This makes devices fail saying: 'device sensed but collection failed'
My biggest issue is that RME categorically bins all device data already collected, making the device disappear from inventory reports.
Rather than test if a mib is supported it just assume it is there. !!!!??? (what about some backward compatibility?)
BugId CSCub09829 describes the issue:
I was able to fix the issue for some older 3750's with package LibInventory ver 3.6.1, but I have several other 'older' device types giving me the same type of error.
Anyone else seeing this?
Anyone got a solution from cisco?
Cheers,
MichelI heard noises that a fix will be available in LMS 4.2.2.
I really wonder how this got through QA in first place.
Cheers,
Michel -
Device sensed, but collection failed
Attempting to gather the inventory information for a couple of Cisco Catalyst 2950G 48 EI Switches. Ciscoworks had problem gathering information from one of my switches. I checked if there's any differences in configuration, routing, or IOS versions. No differences except for management IP address.
Inventory collection job reported "Device sensed, but collection failed".
Attached is the IC_Server.log for the attempted job.Hi,
is there any patch or workaround for this problem?
Our customer can not upgrade the firmware on the devices.
Info about devices:
########DEVICE1################################
WS-C4006 Software, Version NmpSW: 6.2(1)
Copyright (c) 1995-2001 by Cisco Systems, Inc.
NMP S/W compiled on Apr 11 2001, 18:10:53
GSP S/W compiled on Apr 11 2001, 15:57:20
System Bootstrap Version: 5.4(1)
Hardware Version: 1.2 Model: WS-C4006 Serial #: JAB044301U8
Mod Port Model Serial # Versions
1 2 WS-X4013 JAB044301U8 Hw : 1.2
Gsp: 6.2(1.0)
Nmp: 6.2(1)
2 48 WS-X4148-RJ JAE04251J18 Hw : 2.3
3 48 WS-X4148-RJ JAE0433029Y Hw : 2.3
4 48 WS-X4148-RJ JAE043302M7 Hw : 2.3
########DEVICE2################################
Cisco Application Control Software (ACSW)
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2009, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
loader: Version 12.2[120]
system: Version A2(2.3) [build 3.0(0)A2(2.3)]
system image file: [LCP] disk0:c6ace-t1k9-mz.A2_2_3.bin
installed license: ACE-08G-LIC ACE-SEC-LIC-K9
Software
Thanks
Sandro -
RME Inventory never collected issue
Hi, in my Cisco works, i am seeing many devices saying Inventory never collected, or Recently Failed devices.
What could be the cause for Recently Failed? it means they were good before.
and what to do with inventory never collected devices ?:(
attached is screenshot of my licensing and versions i have. Also Error i am reffering to.I think this seems the same issue mentioned in this post: https://supportforums.cisco.com/message/3062089#3062089, when tied together with the other symptoms. In that case, it could be "cured" with as simply as a reboot of the server, or else TAC assistance to clean up the RME package db would be needed.
-
Hi,
I am using collect tool from Sun Studio 12, i used it succeccfully on my system using 64-bit Sun JDK 1.6
but when i try to use it to collect Hardware counter data using 32-bit jvm it failes and shows error while i trying to analyze collect data using "Analyzer" tool
The error message it shows is *"test.1.er***Collector Error: Initializing Hardware counter profiling failed"*
OS version
$ uname -a
Linux m02 2.6.18-92.el5.src-PAPI #1 SMP Tue Jan 27 10:57:40 CET 2009 x86_64 x86_64 x86_64 GNU/Linux
Java version (32-bit version that is not working)
]$ java -version
java version "1.6.0_10"
Java(TM) SE Runtime Environment (build 1.6.0_10-b33)
Java HotSpot(TM) Server VM (build 11.0-b15, mixed mode)
the other Java version that is working fine (64-bit version)
]$ java -version
java version "1.6.0_13"
Java(TM) SE Runtime Environment (build 1.6.0_13-b03)
Java HotSpot(TM) 64-Bit Server VM (build 11.3-b02, mixed mode)
collect command output
]$ collect
NOTE: Linux-64-bit, 32 CPUs, CentOS_5.2 system "mi02" is supported by the Performance tools.
NOTE: The J2SE[tm] version 1.6.0_10 found at java (picked by PATH) is supported by the Performance tools.
usage: collect <args> target <target-args>
Sun Analyzer 7.7 Linux_i386 2009/06/03 [64-bit]
-p <interval> specify clock-profiling
clock profiling interval range on this system is from
10.000 to 1000.000 millisec.; resolution is 10.000 millisec.
-h <ctr_def>...[,<ctr_n_def>]
specify HW counter profiling for up to 4 HW counters
see below for more details
-s <threshold> specify synchronization wait tracing
-r <option> specify thread analyzer experiment; see man page
-H {on|off} specify heap tracing
-M {version|off} specify an MPI experiment
Supported MPI versions: CT8.2, CT8.1, CT8, CT7, CT7.1, OPENMPI, MPICH2, MVAPICH2
-m {on|off} specify MPI tracing
-j {on|off|path} specify Java profiling
-J <java-args> specify arguments to Java for Java profiling
-t <duration> specify time over which to record data
-x specify leaving the target waiting for a debugger attach
-n dry run -- don't run target or collect performance data
-y <signal>[,r] specify delayed initialization and pause/resume signal
When set, the target starts in paused mode;
if the optional r is provided, it starts in resumed mode
-F {on|off|all|=<regex>} specify following descendant processes
-A {on|off|copy} specify archiving of load-objects; default is on
-S <interval> specify periodic sampling interval (secs.)
-L <size> specify experiment size limit (MB.)
-l <signal> specify signal for samples
-o <expt> specify experiment name
-d <directory> specify experiment directory
-g <groupname> specify experiment group
-O <file> redirect all of collect's output to file
-v print expanded log of processing
-C <label> specify comment label (up to 10 may appear)
-R show the README file and exit
-V print version number and exit
Default experiment:
expt_name = test.3.er
clock profiling enabled, 10.000 millisec.
descendant processes will not be followed
periodic sampling, 1 secs.
experiment size limit 2000 MB.
experiment archiving: on
data descriptor: "p:10000;S:1;L:2000;A:1;"
host: `m02', cpuver = 2501, ncpus = 32, clock frequency 1200 MHz.
memory: 16518000 pages @ 4096 bytes = 64523 MB.
Specifying HW counters on `AMD Family 10h':
<ctr_def> == [+]<ctr>[~<attr>=<val>]...[~<attrN>=<valN>][/<reg#>][,<interval>]
<+>
for memory-related counters, attempt to backtrack to find
the triggering instruction and the virtual and physical
addresses of the memory reference
<ctr>
counter name, must be selected from the available counters
listed below. On most systems, if a counter is not listed
below, it may still be specified by its numeric value
<attr>=<val>
optional attribute where <val> can be in decimal or hex
format, and <attr> can be one of:
'umask'
'os'
'edge'
'pc'
'inv'
'cmask'
<reg#>
forces use of a specific hardware register. If not specified,
collect will attempt to place the counter into the first
available register and as a result, may be unable to place
subsequent counters due to register conflicts.
<interval> == {on|hi|lo|<value>}
`on' selects the default rate, listed below
`hi' specifies an interval ~10 times shorter than `on'
`lo' specifies an interval ~10 times longer than `on'
Aliased HW counters available for profiling:
cycles[/{0|1|2|3}],99999989 (`CPU Cycles', alias for BU_cpu_clk_unhalted; CPU-cycles)
insts[/{0|1|2|3}],9999991 (`Instructions Executed', alias for FR_retired_x86_instr_w_excp_intr; events)
ic[/{0|1|2|3}],100003 (`I$ Refs', alias for IC_fetch; events)
icm[/{0|1|2|3}],100003 (`I$ Misses', alias for IC_miss; events)
itlbh[/{0|1|2|3}],100003 (`ITLB Hits', alias for IC_itlb_L1_miss_L2_hit; events)
itlbm[/{0|1|2|3}],100003 (`ITLB Misses', alias for IC_itlb_L1_miss_L2_miss; events)
eci[/{0|1|2|3}],1000003 (`E$ Instr. Refs', alias for BU_internal_L2_req~umask=0x1; events)
ecim[/{0|1|2|3}],10007 (`E$ Instr. Misses', alias for BU_fill_req_missed_L2~umask=0x1; events)
dc[/{0|1|2|3}],1000003 (`D$ Refs', alias for DC_access; load events)
dcm[/{0|1|2|3}],100003 (`D$ Misses', alias for DC_miss; load events)
dtlbh[/{0|1|2|3}],100003 (`DTLB Hits', alias for DC_dtlb_L1_miss_L2_hit; load-store events)
dtlbm[/{0|1|2|3}],100003 (`DTLB Misses', alias for DC_dtlb_L1_miss_L2_miss; load-store events)
ecd[/{0|1|2|3}],1000003 (`E$ Data Refs', alias for BU_internal_L2_req~umask=0x2; load-store events)
ecdm[/{0|1|2|3}],10007 (`E$ Data Misses', alias for BU_fill_req_missed_L2~umask=0x2; load-store events)
fpadd[/{0|1|2|3}],1000003 (`FP Adds', alias for FP_dispatched_fpu_ops~umask=0x1; events)
fpmul[/{0|1|2|3}],1000003 (`FP Muls', alias for FP_dispatched_fpu_ops~umask=0x2; events)
fpustall[/{0|1|2|3}],1000003 (`FPU Stall Cycles', alias for FR_dispatch_stall_fpu_full; CPU-cycles)
memstall[/{0|1|2|3}],1000003 (`Memory Unit Stall Cycles', alias for FR_dispatch_stall_ls_full; CPU-cycles)
PAPI_l1_dcm[/{0|1|2|3}],100003 (`Level 1 data cache misses'; load-store events)
PAPI_l1_icm[/{0|1|2|3}],100003 (`Level 1 instruction cache misses'; events)
PAPI_l2_dcm[/{0|1|2|3}],100003 (`Level 2 data cache misses'; load-store events)
Raw HW counters available for profiling:
*...... { I removed raw counter list to shorten this post}*
See section 3.15 of the "BIOS and Kernel Developer's Guide (BKDG) For AMD Family 10h Processors,"
AMD publication #31116
See the collect.1 man page for more information
analyzer tool version
$ analyzer -v
analyzer: Sun Analyzer 7.7 Linux_i386 2009/06/03
Any idea what is wrong with my configuration? Can we use collect for 32-bit and java apps?
Thanks a lot
Edited by: allo6 on Aug 20, 2009 3:25 AMhi,
how to compile 32 bits libraries on a Centos5 64 bits running on AMD 64 bits (Family 10h)
running
make CC="gcc -m32" CFLAGS="-m32" LDFLAGS="-m32" ARCH=i386
or just
make CC="gcc -m32" CFLAGS="-m32" LDFLAGS="-m32" generate a 32 bit version
/usr/local/perfctr32/lib/libperfctr.so.5.2.6.35: ELF 32-bit LSB shared object, Intel 80386, version 1 (SYSV), not stripped
but the "collect"command (from sun studio for collecting HW values) returns HW counter not suported.
the above generated library is 32 bit but it is intel architecture, The architecture i have is AMD, what "ARCH" flag to spefify for this
if i do not specify any ARCH value there there is this error in the make command
ake[4]: Entering directory `perfctr-2.6.x/examples/perfex'
gcc -m32 -m32 perfex.o x86.o ../../usr.lib/libperfctr.a -o perfex
../../usr.lib/libperfctr.a(event_set_x86.o):(.rodata+0x24): undefined reference to `perfctr_p5_event_set'
../../usr.lib/libperfctr.a(event_set_x86.o):(.rodata+0x28): undefined reference to `perfctr_p5mmx_event_set'
../../usr.lib/libperfctr.a(event_set_x86.o):(.rodata+0x2c): undefined reference to `perfctr_ppro_event_set'
../../usr.lib/libperfctr.a(event_set_x86.o):(.rodata+0x30): undefined reference to `perfctr_p2_event_set'
../../usr.lib/libperfctr.a(event_set_x86.o):(.rodata+0x34): undefined reference to `perfctr_p3_event_set'
../../usr.lib/libperfctr.a(event_set_x86.o):(.rodata+0x38): undefined reference to `perfctr_mii_event_set' -
Listing RDS 2012 R2 collections from powershell remote fails
I'm trying to list different informations of a RDS server farm => from a remote client PC <=
I do following but when typing the last command - I get an error.
Knowing that that same command runs correctly when launched from an RDS server
enter-pssession RDS-SERVER-XYZ.contoso.net
import-module remotedesktop
get-command -module remotedesktop
Get-RDSessionCollection -ConnectionBroker RDS-BRK-1.contoso.net
=> fails with message :
Cannot index into a null array.
At C:\Windows\system32\WindowsPowerShell\v1.0\Modules\remotedesktop\Utility.psm1:54 char:9
+ if ($_script_resource[$Id])
+ ~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidOperation: (:) [], RuntimeException
+ FullyQualifiedErrorId : NullArray
Cannot index into a null array.
At C:\Windows\system32\WindowsPowerShell\v1.0\Modules\remotedesktop\Utility.psm1:54 char:9
+ if ($_script_resource[$Id])
+ ~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidOperation: (:) [], RuntimeException
+ FullyQualifiedErrorId : NullArray
Get-RDSessionCollection :
+ CategoryInfo : NotSpecified: (:) [Write-Error], WriteErrorException
+ FullyQualifiedErrorId : Microsoft.PowerShell.Commands.WriteErrorException,Get-RDSessionCollection
Listing RDS 2012 R2 collections from powershell remote fails / same commandlet from local RDS serevr works fine
Am I missing something ?
MCTS Windows Server Virtualization, ConfigurationAre the Windows Remote Management rules enabled on the inbound firewall of the RDSH server?
If you are running multiple roles on the RDSH server you may need to increase the size of the memory available for powershell remoting.
Run Set-Item WSMan:\localhost\Shell\MaxMemoryPerShellMB 1000 with powershell as an admin and reboot.
HTH,
JB -
I need to set up 9 IPhones and 4 IPads to be used as data collection devices. How can I do that without setting up 13 separate ITunes accounts?
You can use the same account to set up as many devices as you like.
You might also find there are tools to help with a roll out.
http://www.apple.com/support/iphone/enterprise/
tt2 -
Migrating source from one collection to another collection hanging
We are trying migrate a project from one collection to another collection on the same server (TFS 2013.3) and its hanging on what I think is a large changeset. I have let it for for 3+ days but its stuck on this line - any ideas on how to troubleshoot
this?3
I do see this in the top of the log but the path is no longer than 259
[3/11/2015 5:52:15 PM] TfsMigrationShell.exe Warning: 0 : : The workspace root is too long. The migration may fail due to a InvalidPath exception if mapped local path is longer than 259 characters.
[3/11/2015 5:52:15 PM] TfsMigrationShell.exe Information: 0 : : Added TFS workspace mapping from server path '$/Fuse' to local path 'C:\TfsIPData\14\Fuse'
[3/11/2015 5:52:30 PM] TfsMigrationShell.exe Information: 0 : : TFS WorkspaceRoot: C:\TfsIPData\13
[3/11/2015 5:52:30 PM] TfsMigrationShell.exe Warning: 0 : : The workspace root is too long. The migration may fail due to a InvalidPath exception if mapped local path is longer than 259 characters.
[3/11/2015 5:52:56 PM] TfsMigrationShell.exe Information: 0 : : Added TFS workspace mapping from server path '$/Acumen' to local path 'C:\TfsIPData\13\Acumen'
[3/11/2015 5:52:56 PM] TfsMigrationShell.exe Information: 0 : : StartSessionGroup: Starting SyncOrchestrator; now 0 running sessions
[3/11/2015 5:52:56 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Session worker thread [VersionControl] started
[3/11/2015 5:52:56 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Pipeline flow from b391997c-9745-4e5e-a4ff-9d16b30b1fbb to d61e8d15-0a9d-40b2-8854-785f6976f8f2
[3/11/2015 5:52:56 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Generating delta tables for the migration source b391997c-9745-4e5e-a4ff-9d16b30b1fbb
[3/11/2015 5:52:57 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Generating linking delta for the migration source b391997c-9745-4e5e-a4ff-9d16b30b1fbb
[3/11/2015 5:52:57 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Generating delta tables for the migration source d61e8d15-0a9d-40b2-8854-785f6976f8f2
[3/11/2015 5:52:57 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Generating migration instructions for the migration source d61e8d15-0a9d-40b2-8854-785f6976f8f2
[3/11/2015 5:52:57 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Starting basic conflict detection
[3/11/2015 5:53:00 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Finishing basic conflict detection
[3/11/2015 5:53:00 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Loading 50 ChangeGroup(s)
[3/11/2015 5:53:01 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Target AnalysisProvider detecting conflicts in ChangeGroup #267186
[3/11/2015 5:53:01 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Target AnalysisProvider detecting conflicts in ChangeGroup #267187
[3/11/2015 5:53:10 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Target AnalysisProvider detecting conflicts in ChangeGroup #267928
[3/11/2015 5:53:10 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Target AnalysisProvider detecting conflicts in ChangeGroup #267929
[3/11/2015 5:53:10 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Post-processing delta table entries from the migration source d61e8d15-0a9d-40b2-8854-785f6976f8f2
[3/11/2015 5:53:10 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Marking as 'DeltaComplete' the target-side delta table for uni-directional session
[3/11/2015 5:53:10 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Migrating to the migration source d61e8d15-0a9d-40b2-8854-785f6976f8f2
[3/11/2015 5:53:11 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Loading 50 ChangeGroup(s)
[3/11/2015 5:53:11 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Processing ChangeGroup #267185, change 15724
[3/11/2015 5:57:33 PM] TfsMigrationShell.exe Information: 0 : VersionControl: Finished scheduling!
Thanks
ScottHi Scott,
Thanks for your post.
How did you move team project from one collection to another, using the
TFS Integration Tools?
Please try use below setting in your migrate file, you can refer to the answer reply in this
post.
<CustomSetting SettingKey="DetectChangesInCC" SettingValue="False" />
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey. -
Error message: "The share operation Apple Devices 1080p has failed"
Hey,
I have a MacBook Air, OS X version 10.9.3, running Mavericks, with 1.7 GHz and 8 GB memory. I'm running FCPX 10.0.8.
I've had no problems rendering and exporting all sorts of movies and short clips over the last few months, however every time I try to export my last clip, this message shows up after the clip is 10% done exporting: "The share operation Apple Devices 1080p has failed QuickTime Error: - 50"
I've already clicked on "prevent app nap" under Get Info for FCPX.
Does anyone have any idea what's going on, or can offer a solution to this?
Thanks so much!
TerraSince you have already checked the Prevent App Nap box I assume you have seen this thread: https://discussions.apple.com/message/21920134#21920134
Seems likely to me that either one of the files in your timeline is giving you trouble or a render in your timeline is giving you trouble. I sometimes randomly run in to export errors with transitions or titles. Sometimes removing the effect/title from the timeline, deleting the render files or copying and pasting the timeline in to a new project can fix it. -
Keep trying to reinstall itunes on my pc without success. Message keeps coming up saying Service "apple mobile device' (apple mobiledevice} failed to start. Verifyverify that you have sufficent privileges to start system services. What do I do?
Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2 -
Collect participans and collect Non-Partcipants
Hi,
I created all the settings for campaign automation. i mainted evey thing in sequence..after starting campaign automation i am getting this error
Collect participants and collect Non partcipants are not maintained target groups and not maintained BP,s in the target group.
after sending trade invitation the maul form will be reached to customer and customer will respond to survey.then respondents and non respondents will reached to respective nodes.
i maintained rules and conditions in response node.
i dont know why it asking to fill target group's with bp's before start campaign automation.
Normally after starting campaign automation the respondents and non respondents are reached to respective nodes.
can u please provide solution for this problem.
Thanks&Regards
kishor kumarHi Thanks for u r reply.
My dought is here Collect participants and collect NOn Participants nodes are maintained Empty target groups or filled with BP,S
my campaign structure is like this
start node ... > Send Trade Invitation ...> Survey response....> Thank you mail
Collect participants
collect non-participants
collect non reponders ..........> Remainde email
in my scenario system is triggering 2 work flows 1.start campaign process and 2. send target group to channel.
After that it is showing below error messages
Execution Log No business partners exist for execution with current target group Collect Non participants Display
Execution Log No business partners exist for execution with current target group Collect TG Participants Display
After starting campaign automation system execute one by one node.i am totally confused it is strucked here.
can i get any solution for this issue
Thanks&Regards
kishor kumar -
Collective and NOn-collective order fields???
i am not able to find which table contains Collective and Non-collective orders field in Production Order Change (CO02)???
Hi,
Please check the table AFKO.
If AFKO-LEAD_AUFNR is same as AFUK-AUFNR, then it is collective Order.
if AFKO-LEAD_AUFNR is blank or space, then it is normal Order.
If you want to check whether the material is collective or not, you can find the same in MARC-SOBSL = 52.
Hope this is useful response for your query.
Thanks
Lakshmi -
Export file list from collection/subfolder in collection window
i would find it very helpful to be able to export the file names of files contained in one a collection as a .txt or similar list. there are scripts and complicated things to do this out of folders, but there doesn't seem to be a way to do this with collections.
i might for example have a project, that includes a collection of images and renaming files differently for final output. while i'm working on the project im fine with having the collection in the collection tab. but when i'm done, i want to get rid of it, since i don't want the collection tab clogged with old collections from finished projects. but with the finished project in my archive (images renamed for output) i still want a list with the original filenames - otherwise it will be hard to find the original in the future. at the moment i am attaching screenshots of the collection before i delete it, but that only really works up to about 100 images. and of course the screenshot is not searchable.
or a client organises image selection in a collection and has to send me the files list. at the moment they have to type it all up.
this feature shouldn't be hard to program i guess, but would make things a lot easier.
also the possibility to organise the collections in subfolders (in the collections tab) would be great.Ordinary Collections are just text files and can be found:-
Mac: Users/[Username]/Library/Preferences/Adobe/Bridge CS5/Collections
Win 7: Users/[Username]/AppData/Roaming/Adobe/Bridge CS5/Collections -
Ordering of Collection Sets and Collections (inside Collection Sets)?
What are the rules for how elements (specifically, collections and other collection sets) are ordered within a collection set?
I was trying to get a collection to appear at the top of the list of items in a collection set, but it seems to get stuffed below all the other collection sets regardless of the name given to the collection.
-StrathglassCollection Set / Smart Collections / Collections (Alphabetical in each case)
The same applies inside a Collections Set.
So a collection will never appear above a smart collection or collection set regardles of it name. If you create a Collection Set then create two Sets within (01, 02) Set 01 could contain Collections and thereby would appear above smart collections in set 02. -
Xen - device model: spawn failed
I have a Xen-based VM configuration which I've used without issue for well over a year. After running some updates and rebooting yesterday (either of which could be coincidental), the VM will no longer start:
# xl create leonids.xl.cfg
Parsing config from leonids.xl.cfg
libxl: error: libxl_dm.c:1371:device_model_spawn_outcome: domain 1 device model: spawn failed (rc=-3)
libxl: error: libxl_create.c:1186:domcreate_devmodel_started: device model did not start: -3
libxl: error: libxl_dm.c:1475:kill_device_model: Device Model already exited
It probably shouldn't matter, but here's the basic config which I pared down in an attempt to resolve this issue:
name = "vm1"
memory = 3072
vif = [ 'bridge=xenbr0' ]
disk = [
"phy:/dev/loop0p1,xvdb1,w"
builder = "hvm"
vnc = 1
vnclisten = '0.0.0.0'
vncdisplay = 1
And the loop device is created automatically by losetup after:
# modprobe loop max_parts=15
And I don't know if anything in this update would have caused it, but here's the pacman log anyway:
[2014-08-13 22:27] [PACMAN] Running 'pacman -Syu'
[2014-08-13 22:27] [PACMAN] synchronizing package lists
[2014-08-13 22:28] [PACMAN] starting full system upgrade
[2014-08-13 23:23] [PACMAN] upgraded bash (4.3.018-3 -> 4.3.022-1)
[2014-08-13 23:23] [PACMAN] upgraded chromium (36.0.1985.125-1 -> 36.0.1985.143-1)
[2014-08-13 23:23] [PACMAN] upgraded convertlit (1.8-6 -> 1.8-7)
[2014-08-13 23:23] [PACMAN] upgraded cracklib (2.9.0-2 -> 2.9.1-1)
[2014-08-13 23:23] [PACMAN] upgraded fakeroot (1.20-1 -> 1.20.1-1)
[2014-08-13 23:23] [PACMAN] upgraded gpgme (1.5.0-1 -> 1.5.1-1)
[2014-08-13 23:23] [PACMAN] upgraded kbd (2.0.1-1 -> 2.0.2-1)
[2014-08-13 23:23] [PACMAN] upgraded krb5 (1.12.1-1 -> 1.12.1-2)
[2014-08-13 23:23] [PACMAN] upgraded libiscsi (1.7.0-2 -> 1.12.0-1)
[2014-08-13 23:23] [PACMAN] upgraded libcacard (2.0.0-4 -> 2.1.0-2)
[2014-08-13 23:23] [PACMAN] upgraded libidn (1.28-2 -> 1.29-1)
[2014-08-13 23:23] [PACMAN] upgraded libmariadbclient (10.0.12-2 -> 10.0.13-1)
[2014-08-13 23:23] [PACMAN] upgraded xcb-proto (1.10-2 -> 1.11-1)
[2014-08-13 23:23] [PACMAN] upgraded libxcb (1.10-3 -> 1.11-1)
[2014-08-13 23:23] [ALPM-SCRIPTLET] >>> Updating module dependencies. Please wait ...
[2014-08-13 23:23] [ALPM-SCRIPTLET] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> Starting build: 3.16.0-2-ARCH
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [base]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [udev]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [autodetect]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [modconf]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [block]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [filesystems]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [keyboard]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [fsck]
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> ERROR: file not found: `fsck.btrfs'
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> WARNING: No fsck helpers found. fsck will not be run on boot.
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux.img
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> WARNING: errors were encountered during the build. The image may not be complete.
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> Starting build: 3.16.0-2-ARCH
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [base]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [udev]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [modconf]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [block]
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2014-08-13 23:23] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: smsmdtv
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [filesystems]
[2014-08-13 23:23] [ALPM-SCRIPTLET] -> Running build hook: [keyboard]
[2014-08-13 23:24] [ALPM-SCRIPTLET] -> Running build hook: [fsck]
[2014-08-13 23:24] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2014-08-13 23:24] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: /boot/initramfs-linux-fallback.img
[2014-08-13 23:24] [ALPM-SCRIPTLET] ==> Image generation successful
[2014-08-13 23:24] [PACMAN] upgraded linux (3.15.8-1 -> 3.16-2)
[2014-08-13 23:24] [PACMAN] upgraded lirc-utils (1:0.9.0-75 -> 1:0.9.0-76)
[2014-08-13 23:24] [PACMAN] upgraded mariadb-clients (10.0.12-2 -> 10.0.13-1)
[2014-08-13 23:24] [PACMAN] upgraded mariadb (10.0.12-2 -> 10.0.13-1)
[2014-08-13 23:24] [PACMAN] upgraded python-setuptools (1:5.4.2-1 -> 1:5.5.1-1)
[2014-08-13 23:24] [PACMAN] upgraded xfsprogs (3.2.0-1 -> 3.2.1-1)
Any ideas what may have caused this?As an update, this problem occurs exclusively with loop devices, whether created automatically through the loop module or manually through kpartx.
Maybe you are looking for
-
What use of having double precision in java.awt.geom?
Hi, I am trying to draw a line using Line2D with this param: g2d.draw( new Line2D.Double( 1.1d, 1.5d, 1.9d, 1.5d ) ); in my own JPanel paint method. However, the result is that the panel does not display a line nor a dot at all. Only when i change it
-
Is there a way to add snooze conditions to iCal?
I've noticed that when an iCal reminder alarm pops up a window you can "snooze" the reminder alarm for a period of time. The weird thing is that some of my Macs have more options than other. Some have: Repeat 1 day before event starts Repeat 2 hours
-
64-Bit PCI space on OpenSolaris
** As a disclaimer, I am working on OpenSolaris, not Solaris, so I am not sure if this is the right place to post. ** Hello, I've been trying a new feature on my BIOS that allows to memory map PCI device registers to spaces above 4G. However, when I
-
NOW behaviour in siebel Analytics 7.8
Hi All, We have a Calculated measure column (BIRTH_age) using NOW() in rpd we have a Answer created with a filter like BIRTH_age>18 on the column in Siebel Analytics 7.8 and a segment is created over this analysis. when we are executing update count
-
Restricting a production order from releasing
Hi, How can i restrict a production order from releasing if material is not available? Regards, samir Edited by: wadajkar on Jun 2, 2010 2:51 PM Edited by: wadajkar on Jun 2, 2010 2:51 PM