Rollback does not work between two databases

I have two databases, A and B and a database link.
I have a procedure in database A that has calls to procedures of database B. When commit in A then gives error (ora-06512), then I make rollback, but only does for database A, in database B has recorded the data. It's normally? What's happens?
Thanks

I'm afraid you'll need to give as more information; ORA-06512 is a very generic message and is used to indicate which line another error occured. Can you tell us what that error was, and exactly what you're trying to do?
Thanks,
Colin

Similar Messages

Shared variable does not work between two computers

I am using LabVIEW 8 on Windows XP computers.
1. On one computer I have created two projects, writeProject and readProject.
2. In the writeProject I have a shared variable, writeData, which is "network-published" double. In this project I have a writeData.vi which in while loop assigns a random value to the writeData variable.
3. In the readProject I have a shared variable, readData, which is "network-published" double and is bound to the writeData variable. This is on the same computer as the writeProject.
4. I run both the writeData.vi and the readData.vi and all works fine.
5. Now, I create a readProject on a diferent computer. Perform all the steps as described above and also in tools/shared variable/register computer, I have entered the IP address of the target computer on which the writeData shared variable exists.
6. Binding the readData variable fails in the following way. When I browse for the source, in the "Select Source Item" dialog, I see <IP> <Populating Node...>, where <IP> is the IP address of the source computer (on which exists the writeData shared variable). A very long time later it is still "Populating Node...". Neddless to say, this readData.vi does not work!
What am I doing wrong? Or, perhapse what else do I need to do to make it work?

Hi,
I would suggest checking out the two KnowledgeBases I have linked below for common issues with Network Shared Variables. Let me know the results. Thanks!
Troubleshooting Network-Published Shared Variables
Why Are My Network Shared Variables Taking Very Long to Initialize?
Stephanie

Call does not work between two SX80

Hello,
I have two SX80 TelePresence Devices installed on same Network. I want to make call ( IP to IP ) between two Sx80 and the Result was no call Establish between them.
Are there any configuration required to do it from my side to add to the SX80?
Note: this two SX80 WORKING stand alone ( No CUCM or MCU).
Warm Regard,
Idris

Log in using SSH and ping one from the other to see if they can see each other, also ensure CallSetUp Mode is set to "Direct" and set default call protocol to H.323.
/jens
Please rate replies and mark question(s) as "answered" if applicable.

Copy-Item does not work between two azure vms

hi
I have 2 VMs hosted in Azure and i tried to copy using power shell
Copy-Item -Path C:\testSource\test.txt -Destination \\10.0.0.4\testshare
I got the following error
Copy-Item : Source and destination path did not resolve to the same provider.
At line:1 char:1
+ Copy-Item -Path C:\testSource\test.txt -Destination \\10.0.0.4\testshare -Force
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ CategoryInfo : InvalidArgument: (System.Collecti...[System.String]:Collection`1) [Copy-Item], PSArgumentException
+ FullyQualifiedErrorId : CopyItemSourceAndDestinationNotSameProvider,Microsoft.PowerShell.Commands.CopyItemCommand

Hi,
I will mark Sam's post as answer, if you find that doesn't give you help, please feel free unmark it and follow up.
Best Regards,
Jambor
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

IPod nano version 6: random turn off, volume controls don't work, does not turn off, skip does not work. Two years old! Next version of nano has no clip and same amount of storage. I do not want to give up my version 6!

iPod nano version 6: random turn off, volume controls don't work, does not turn off, skip does not work. Two years old! Next version of nano has no clip and same amount of storage. I do not want to give up my version 6!

Make a Genius Bar appointment at your nearest Apple Store and pay $75 USD for an out-of-warranty replacement.

Datasocket does not work with two network cards

If I have two ethernet card in a PC. The Datasocket server does not work if the second card is enabled. It keeps displaying resolving IP Address. I am wondering if there is a solution for this problem.
Thanks

Thanks for you reply. One card has a static address(10.20.35.1), which is used for Data socket, and the other card uses a dynamic IP address. The card with dynamic address is only used for connecting the PC to the company’s network.
The second card, when turned on causes the Datasocket server problem. In the Datasocket Server manager I have only two IP addresses under Permissions Groups. (10.20.35.1 and 10.20.35.11. 10.20.35.11 is the IP address of the remote PC with labview application. The Datasocket is used to transfer data between the two PC’s)
I am wondering if my set up for hosts in Datasocket Server manager is not correct.

Mail in Mavericks not working between two macs.

Hello all
I have a 2012 iMac as well as a 2009 MacBook Pro. I am running Mavericks on both machines. I'm having issues with my exchange e-mail contacts and calendar, syncing between the two devices. I will get it to work on one device or the other but not both at the same time. More specifically in mail when it is working on one computer and I go to check my mail on the other it asks me to put in my password for that e-mail account. Every time I do this it does not work and it always returns an error. If I go to delete an account on either computer it tells me the account is linked to "Internet account" under settings for the computer. When I delete the exchange account from "Internet account" it warns me that it will delete the account off of both macs. When I re-add the exchange account mail, contacts and calander all work for whichever computer I add it on. But the other computer will only show calander or contacts not all three.
Does anyone have an idea what might be wrong or have a solution? This is very frustrating and I cant seem to find a solution.

Hi,
Those last two I do not have on my iMac that is working and part of the issue I have in testing is I don't have a second Mac that will run Yosemite.
Realistically it could be any of the ones that contain com.apple.ids.service.com.apple.private.alloy.***.plist
The plain SMS.plist only states it has been started up not what the Mac is linked to.
Unfortunately nothing is standing out as the Specific one for me at the moment.
9:34 pm Sunday; December 28, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

Purchased adobe acrobat x serial number does not work after two computers i need it put on a third computer help

I purchase adobe acrobat x I put it on two computers in my office I need to put it on one more but the serial number does not work anymore is there a way to put it one the third computer?

Also, you can only use it on two computers if they belong to the same person, are used only by that one person, and are not used at the same time. To install on two computers for two people needs two licenses. Adobe sell volume licenses, but do not sell an "all the computers in the office" license.

WCCP does not work between WSA and ASA

I have configured WCCPv2 between WSA S160 ( 6.3.1-025) and ASA5540 (8.2(1)109).
Everything seems to be OK by "show wccp *" on ASA and showing wccp debugging messages (level 4) on S160. Despite of it, WCCP redirection does not work.
If I use packet-capture I figure out that S160 receives GRE packets with TCP SYN from particular LAN host to WWW sites but S160 does not handle them and does not send anything back to ASA.
It is an Exempt from authentication for this LAN host and in Forward proxy mode everything works well.
I have attached an example of a packet-capture (S160.txt - renamed from .cap) and debugging messages from S160 & "show" from ASA.
Does anybody have any idea what the problem is and how I can resolve it ?

IronPort Support team helped me to find the trouble:
If I wish to handle specific port's (80, 8080, etc.) traffic by the transparent proxy I need to configure this port like a listener for the FORWARD proxy
("Security Services" -> "Proxy Settings" -> "HTTP Ports to Proxy")
The WSA guide doesn't clearly say about it.
So the Discussion can be closed ...

Synchro does not work between Ipad, Iphone and Mac

Good evening,
I have an IMAC, iPhone 5s and an Ipad all with the last IOS version and synchro does not work at all.
My iCloud address is not with iCloud but with hotmail.
I dod not get any suitable answer from the retailers in Budapest.
Does anybody have an idea? Thank you.
Greg

good evening!
i switch on in iCloud the calendars on both Iphone and Ipad/mac of course but nothing happened.
Can it be because my iCloud address is with hotmail?

Calender does not work between IOS5 and IOS4.3 iPad

We have two iPads. One is unfortunately on IOS5 and the other is on IOS4.3. When i activate the calender on both devices the shared calender is seen on the IOS4.3 iPad but not on the IOS5 iPad. Whatever i try using google accounts or iCloud it only works one way. Seems like another bug in IOS5? The CalDav fucntion that is proposed on multiple answers does not seem to work at all on the IOS5 iPad, it simply does not accept the password. Is there a simple way out? Or would i need to upgrade the second iPad also to IOS5 as i cannot downgrade the first iPad back to IOS4.3?
help...

The iOS 4 device will not be able to use iCloud, of course.
As to Google calendars, I found that there's something different about how Calendar works in iOS 5. I had a couple Google calendars that I was subscribed to in iOS 4, but when I upgraded, those calendars stopped updating, and I could not figure out for the life of me where those calendars were defined. I ultimately had to remove them and then re-add them in Settings > Mail, Contacts, Calendars. Click Add Account, and if you only want a calendar, click Other, then Add CalDAV Account or Add Subscribed Calendar.

Home Sharing does not work between a new computer and old computers

Hello Guys,
I recently brought a new sony vaio laptop however it does not seem to work with my current homesharing system. My old laptop and the old computers which worked together, still work fine across different versions of itunes including the newest one. However my new laptop has the new itunes but it doesn't work. The old computers/laptops can pick up the new laptop and homeshare across however this new one cannot sense any. All are on same network as well as all have been athorised and on same homesharing. Doesn't seem to be firewall either. Help Windows 8 to Windows Vista to iOS newest one.

Fixed my problem. I just needed to upgrade the firmware on my router.

IChat video chat not working between two iMacs running OSX Leopard 10.5.1

My mother in law just got a 20" iMac (metal) and is connected to her wireless router.
I tried doing a video iChat with her, and it is not working. I am able to successfully test iChat with the three apple iChat test AIM buddy accounts.

Screen names of Test accounts are here http://www.ralphjohns.co.uk/ContactTesters.html
9:40 PM Wednesday; February 20, 2008

Advanced Queuing Schedule Propagate does not work between DBs

Hi,
we want to transfer messages between different databases on ORACLE 8.1.6.1 (Windows NT 4 SP6). When we use the procedure schedule propagate, we got no error message in DBA_QUEUE_SCHEDULES, but no data is found in the destination queue on the target DB. The database link to the other DB works. The propagation runs, because we see that sequentially job numbers are assigned (AQ$_SCHEDULES). In the same DB the propagation works properly. In which way can we find out, what is wrong? I already read the "AQ to a remote database" and the "Propagation over instances" postings.
Kindest regards,
Dirk
null

<BLOCKQUOTE><font size="1" face="Verdana, Arial, Helvetica">quote:</font><HR>Originally posted by kmeiyyap ():
Hi,
Did you see any snp trace files? If so, that might give you some lead as to what error happened.<HR></BLOCKQUOTE>
There are trace files, but they have nothing to do with my AQ job.
null

Multicast Does not work between different VLANS

Hi,
I have problems with multicast. On the same VLAN i can see the SAP announcement in VLC and play, but on different VLAN i can see SAP but i cant play it. The play turn to pause and the video doesn´t appear.
I have 2 Cisco 6500 switch CORE with GLBP configured but not working. In the second switch i have all interfaces in shutdown. The first core switch have L3 routing enable.
The Global configurations:
ip multicast-routing.
I have the transmitter PC on vlan 51 i transmit to 230.0.0.50 group an im trying to recive on vlan 80. The vlans configurations are:
Vlan 51
ip address x.x.31.254 255.255.255.0
ip pim sparse-dense-mode
Vlan 80
ip address x.x.80.1 255.255.255.0
ip pim sparse-dense-mode
I have 2 Cisco 2960 (L2 only) for the access.
The principal commands outputs are:
CORE1#show ip mroute | inc 230.0.0.50
(*, 230.0.0.50), 01:50:50/00:02:21, RP 0.0.0.0, flags: DC
CORE1#
CORE 1
interface Vlan1
ip address x.x.1.1 255.255.0.0
ip access-group 101 out
no ip unreachables
ip pim sparse-dense-mode
mls rp ip
interface Vlan51
ip address x.x.31.254 255.255.255.0
ip access-group 151 out
ip helper-address x.x.x.x
ip helper-address x.x.x.x
no ip unreachables
ip pim sparse-dense-mode
mls rp ip
interface Vlan80
ip address x.x.80.1 255.255.255.0
ip access-group 150 out
no ip unreachables
ip pim sparse-dense-mode
glbp 80 ip x.x.80.254
glbp 80 timers 5 18
glbp 80 timers redirect 600 7200
glbp 80 priority 254
glbp 80 preempt delay minimum 60
glbp 80 authentication text glbpkey
glbp 80 forwarder preempt delay minimum 60
CORE2
interface Vlan1
ip address x.x.1.4 255.255.0.0
ip access-group 101 out
no ip unreachables
ip pim sparse-dense-mode
mls rp ip
interface Vlan51
ip address x.x.31.2 255.255.255.0
ip access-group 151 out
ip helper-address x.x.x.x
ip helper-address x.x.x.x
no ip unreachables
ip pim sparse-dense-mode
shutdown
mls rp ip
glbp 51 ip x.x.31.254
glbp 51 timers 5 18
glbp 51 timers redirect 600 7200
glbp 51 preempt delay minimum 60
glbp 51 authentication text glbpkey
glbp 51 forwarder preempt delay minimum 60
interface Vlan80
ip address x.x.80.2 255.255.255.0
ip access-group 150 out
no ip unreachables
ip pim sparse-dense-mode
shutdown
mls rp ip
glbp 80 ip x.x.80.254
glbp 80 timers 5 18
glbp 80 timers redirect 600 7200
glbp 80 preempt delay minimum 60
glbp 80 authentication text glbpkey
glbp 80 forwarder preempt delay minimum 60
end
Someone can help?
Thanks,
Alfredo

Hi johnd...
Im using VLC 1.1.2 (i can not update because i have a DVDT2 card to capture the digital terrestrial television and it only work in this version). I have all the firewalls down.
This is the output for the show ip igmp snooping groups on the 2960.
80 230.0.0.50 igmp v2 Gi1/0/21, Gi1/0/24
Port G1/0/21 is where the receiver is conected and the 24port is the trunk.
Jon, i revert and this is the output. I put the ip pim rp-address the same of the lookpback that i create previously.
(*, 230.0.0.50), 00:37:46/00:02:19, RP 192.168.230.230, flags: SJC
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Vlan80, Forward/Dense, 00:09:52/00:00:00
The strange thing is that I have more than 40 vlans and it only fail in some vlans like 80.

Rollback does not work between two databases

Similar Messages

Maybe you are looking for