Rollup a reduced set of monitors to a class / group

Hi there,
As part of a distributed application, I am looking to add only the Operating System and Hardware health rollups of a computer object to the DA.
Is there any way to achieve this without creating a new, un-hosted class and leveraging dependency monitors? I have tried a sub-class and disabling the monitors that I don't want, but that disables them for the object everywhere.
Regards
Jerome

Hi Yan,
Thanks for that. Unfortunately that has the same problem as disabling the monitor for a group. The health state is disabled everywhere in OpsMgr and not just for the DA that I am trying to create.
In the end, I have created another class and created relationships and dependency monitors to the components I want the health to roll up from.

Similar Messages

  • How do I set external monitor to work with my G4 iMac?

    I just bought a 22" Proview LCD monitor to use with my iMac b/c it's monitor is pretty much gone. It did not work for six months, then came on for 1 day and went out again.
    Long story short, since I've hooked up the new monitor when I print in iPhoto the pictures come out too dark and the color is not what it used to be.
    How do I fix it so my monitor's calibrations match the original? Or, whatever I need to do to fix it.
    I print a lot of pictures and I need this to work correctly.
    Thanks.

    Snoot, welcome, your new monitor just needs to be calibrated. From the finder under the Apple scroll down to System Preferences, Click the Desktop & Screen Saver icon and set the desktop picture to a Medium Gray.. You can change this back when you are done. Now go back by clicking Show All and click the Displays icon, then choose Display in the upper tabs and set your preferred resolution. Set your monitor brightness at about medium (if there is one) and at Colors choose Millions. Now choose Color from the upper tab and select Calibrate. Choose Expert Mode at the introduction and follow the on screen instructions. After making all of the Hue,Value and Saturation adjustments your must save the setting back to the Display profile.
    Also some applications have monitor selection in there preferences, so just make sure that you choose your present Display Profile for that particular application.
    Joe
    Mac Pro 2.66 Ghz   Mac OS X (10.4.10)   Users (RAID 0), PM G4 (10.3.9, PM 6500 (10.2.8)

  • Trying to install Premiere Elements 10 on Windows 7 but keep getting error message 'A reduced set of content has been installed' - help!

    We bought Premiere Elements 10/Photoshop Element 10 a while ago and it worked brilliantly on our Window XP machine, but since we moved to Windows 7 last year we can't get Premiere Elements 10 to work properly and always get the error message 'A reduced set of content (Instant Movie Themes, Title and Menu templates, etc) has been installed. You can install the full content by inserting your Content DVD or downloading it. Do you want to install now?'. So I've tried reinserting the DVDs and installing them. I've uninstalled all the software and started again, but each time I get the same message at the end of the process. I've spoken to the computer shop I bought the computer from and they say Windows 7 is incompatible, but that doesn't seem to be what the Adobe web site says. Please, any advice welcome as I've got a year's worth of videos I need to edit.
    Thank you!
    Adobe Premiere Elements 10.0 
    Windows 
    2 GHz or faster processor with SSE2 support; dual-core processor required for HDV or AVCHD editing and Blu-ray or AVCHD export.
    Microsoft Windows XP with Service Pack 2, Windows Media Center, Windows Vista® (all applications run native on 32-bit operating systems and in 32-bit compatibility mode on 64-bit operating systems), or Windows 7 (Adobe® Premiere® Elements Editor runs native on 32-bit and 64-bit operating systems; all other applications run native on 32-bit operating systems and in 32-bit compatibility mode on 64-bit operating systems)

    cathyj
    Are you working with Windows 7 32 bit or 64 bit? What video card/graphics card does your computer use? NVIDIA GeForce? And, are you doing your download and installing with antivirus and firewall(s) disabled?
    Premiere Elements 12 is compatible with Windows 7, 8, or 8.1 64 bit.
    If you have tried to obtain the Premiere Elements 10 Content from the installation disc labelled for Content for your version and operating system and that is not working, then can try downloading and installing the Content from the following Adobe link if you do not decide to click on the message to initiate the content download from within the program.
    http://www.adobe.com/special/premiereel/downloads/
    We will be watching for your progress.
    ATR

  • Setting a monitor into portrait mode in OS X 10.1

    Is there any way I can set a monitor to display a portrait mode? (f.g. making 1024 x 768 into 768 x 1024) I am certain you can't do this with OS X 10.1, but is there any software utility that can "trick" it?

    Hi, kittytom200x. If the monitor wasn't designed to pivot and didn't come with a 10.1-compatible proprietary driver to enable rotating the displayed image and relocating the menu bar, I seriously doubt that you're going to find any way to accomplish that. Particularly not in OS X 10.1, which was far from complete and full-featured (to say the least!), and supported few hardware tweaks or customizations.

  • Set default monitor at boot before X?

    Hi,
    I have a plasma tv and a normal 24" monitor plugged into a Nvidia GTX 960 both are DVI.
    When I boot up the TV is the default and the monitor doesnt display anything.
    Both work fine in X but how can I set the monitor to be the default monitor on boot?
    Thanks.

    shtnarg wrote:I wouldn't think both ports are different? That'd be unique! Try physically switching them at the video card side. I think it should work.
    Honestly the DVI ports are two different types DVI-D and DVI-I. Only one is able to covert DVI to old VGA with an adaptor. So the TV has to be lugged into that port as it's VGA.
    Here's a picture of my actual card http://www.gigabyte.com/fileupload/prod … 44_big.png
    Those extra 4 holes in the port on the left are what allow the analogue conversion. I think manufactures are starting to phase out the old DVI-D like they did for VGA.

  • PE7 is "not full" and is a reduced set

    ok so i bought this program quite some time ago and i still have it on my computer. and when i opened it it says that
    "A reduced set of content (Instant Movie Themes, Title and Menu Templates, etc) has been installed. To install the full content set please insert your
    program DVD and run Install Content.exe If you do not have a program DVD please visit
    http://www.adobe.com/support/downloads/product.jsp?product=101platform=windows
    to download the content installer"
    the thing is i don't have the DVD and when I went to the link:
    http://www.adobe.com/support/downloads/product.jsp?product=101platform=windows
    it is broken. please help. thanks.

    Is it possible the reason you don't have a DVD is because the software was bought as an electronic download?
    If so, the following link may help.
    http://kb2.adobe.com/cps/406/kb406662.html
    Basically what they say is that the executable content file is likely already on your computer. Look for a file called PRE7_Cont_WWEFGJ.exe on your computer, and if it is there, double click it to install the full content.
    And if that file is not there, the full content for PRE7 is available at this link:
    http://www.adobe.com/support/downloads/product.jsp?product=101&platform=Windows

  • PE 10 "Reduce set of content- " error:

    PE 10 “Reduce set of content… ” error:  I downloaded both .exe and .7z files successfully after 8 hours to My Download area, launched program and the PE 10 Content all folders and files saved to desktop successfully. However, The PE 10 “reduce set of content” error still occurs. 
    I am assuming that PE 10 Content folder and files should be saved with the “existing Adobe PE10 files”.  Can I copy and paste files to the correct location? What is the correct location? Any solution?

    Now I have bigger problems.  The entire PE10 program has been removed from my computer but I have the PE10 Content files.  Help!

  • TS1258 Is there a way to re-set the monitor with an external keyboard, since my internal keyboard is not working?

    My internal keyboard and mouse have stopped working, so I have attached an external keyboard and mouse. But now I need to re-set the monitor. Can I do it with an external keyboard?
    I have the dark bands at the bottom of the internal display.

    You cant switch off the power to the monitor but you can send it to sleep.
    1 - Apple > System preferences > energy saver: set the monitor to sleep at the shortest duration
    2 - While the second display is connected and powered on,  System Preferences > Displays > Arrangement:  deselect the Mirror Displays option
    While the presentation plays on the secondary display, the Mac display will go to sleep as there is nothing on the screen during play, entering display sleep within seconds.

  • Reduce set-up time

    Hi All !
    My Voip network use : Cisco As53xx , 54xx , R72xx , PGW2200 .
    When i dial , after finish press the called digit --> tut --> tut --> tut (soo long) ---> ring back tone.
    How can i reduce set up time .
    what parameters on Gateway , PGW2200 can effect this time ?
    pls help me
    Thanks
    Taipeitel Coo

    Hello
    Its depend from what actually happen in the network.
    I try to explain.
    In reality we have some phase with call setup.
    1. h225 tcp establishment.
    2. Alternative route lookup if primary fail and so on.
    3. Signaling.
    What actualy happen is unclear.
    If 1. you can try decrease h225 setup time on the
    gateway.
    if 2. this is trade-off between setup time and guaranteed service.
    if 3. its again depend which node introduce delay and why.

  • Set main monitor before startup

    Hi.
    The monitor of my iMac suddenly stopped workin, now I have a second monitor connected to it via DVI-VGA but it is set as secondary display, so when I power the broken iMac on I still cannot use it.
    I already read threads about Target Disk Mode, but I do not have another Mac available so I cannot even clone the hard disk.... I need to set the second monitor as main: is there a way to do it at the login screen? Any way to invert the two monitors with a shortcut?
    Any idea is welcome!

    I worked out the dock part. After working out that the two screens are see as one larger desktop I just need to swap the screen arrangement so my dock was showing on the right edge which is where my Dell is set now.
    Any information on how to set one monitor over the other as the main monitor would be helpful.
    TOnyTOny

  • Setting the header of a Column group in a Advanced table dynamically

    Hi All,
    There is a requirement to set the Header of a column group in a Advanced table dynamically by fetching the values from a view attribute.
    Code :
    OAAdvancedTableBean spiderTbl1 ;
    Problem:
    It is not able to set the value for the header inspite of getting the handle of the bean.
    Analysis:
    the same piece of code works for
    1) Setting the text of the advanced table
    2) Setting the header of a column in a column group
    Please let me know if there is anything more that needs to be done for setting the prompt of a column group header.
    Thanks in advance!

    I have posted it without giving the complete code by mistake. Below is the code:
    OAAdvancedTableBean spiderTbl1 ;
    OASortableHeaderBean spiderHdr1;
    spiderTbl1 = (OAAdvancedTableBean)webBean.findChildRecursive("SpiderCatTbl1RN");
    if (spiderTbl1!=null){
    spiderHdr1= (OASortableHeaderBean)spiderTbl1.findChildRecursive("AnalogHdr");
    if (spiderHdr1!=null) {
    spiderHdr1.setAttributeValue(OAWebBeanConstants.PROMPT_ATTR,
    new OADataBoundValueViewObject(spiderHdr1,
    "SpiderCategory1",
    "ProjRegPVO1"));
    }

  • GET SET function in a dynamic Class?

    Is it possible to add a GET SET function in a dynamic class, like we can add properties to a dynamic class?

    correction :
    MyObjectProxy extends ObjectProxy{
         override callProperty(
              // your dyna logic
    and expose new MyObjectProxy(dynaInstance)

  • Sun ONE Studio 4 aka Forte: How to set the output path for classes ?

    Help !
    Beginner's question:
    Sun ONE Studio 4 aka Forte:
    How to set the output path for classes ?
    As default, the class files are created in the same directory as the
    sources.
    In opposite, both JBuilder and Together support that there is a tree
    with the sources and another tree with the classes.
    The first answer I got was "not possible with Forte, but just if you write your own "ANT Build script" !
    a) Please point me to a ready-to-use ANT script for this purpose, if such is available
    b) Is using ANT instead of the MAKE as comfortable ? Besides the separation of sourcecode and classes, I would like to keep everything else to be the same, i.e. I don�t want to edit the ANT file if I enlarge the project by directories or files.
    Tia
    Sincerely
    Rolf

    You can set S1S's options to place newly created .class files in a specific location.
    Identify the compiler that is being used - Open the S1S's Tools/Options window, expand Editing and select Java Sources. Note the Default Compiler value. (If it's one if the Ant options, you use Ant to specify this option, not S1S.)
    Open the S1S's Tools/Options window, expand Building/Compiler Types and select the appropriate compiler.
    The Properties tab of the compiler has the property Target, which sets the filesystem where the compiler output is directed. If you choose <not set>, the .class files are written to their source directory.
    When you set the Target, your change affects all classes that use this compiler.
    Very few options can't be set in S1S; the challenge is finding out where they're set!

  • The iPad doesn't seem to want to set up an email for a "group" in my contacts. On my iMac, when I type the name of a group, the email addresses of everyone in the group appear in the "To" line of a new message. Not so with the iPad. Help?

    The iPad doesn't seem to want to set up an email for a "group" in my Contacts. When I type the name of a group in the "To:" line of a new message on my iMac, all the email addresses of the group automatically appear. Not so with my iPad. Help?

    Apparently Groups are not supported in the Mail App on the iPad. Read this thread and see Michael Morgan's post for a workaround.
    https://discussions.apple.com/message/13084823#13084823

  • How to set fill, stroke & color to a group

    First of all, I must say I'm a complete beginner in Javascript so please have patience with me.
    What I'm trying to do is to set a lot of groups to specific fill, stroke & color using a function.
    var docRef = app.activeDocument;
    var Reg = docRef.swatches["[Registration]"].color;
    var mm = 2.834645;
    var lineWidth=0.12*mm;
    group1.stroked=true;
    group1.strokeColor = Reg;
    group1.filled = false;
    group1.strokeWidth = lineWidth;
    This works, but I have to this for every group and there are lots of them.
    So I tried to make a function:
    function setAttributes(temp)
    temp.stroked=true;
    temp.strokeColor = Reg;
    temp.filled = false;
    temp.strokeWidth = lineWidth;
    And then call that function for each group:
    setAttributes(group1);
    setAttributes(group2);
    setAttributes(group3);
    etc.
    Of course, this doesn't work since I have incredible programming skills
    Please help.
    Thanks!

    The script as it is should ONLY change the path items that are in your 'first level' of group items… If you need to change the properties of path items outside of the groups then you could add another loop… Heres one way you add the extra loop:
    var docRef = app.activeDocument;
    // Set variable to your color
    var reg = docRef.swatches.getByName("[Registration]");
    // Set a variable to the document path items collection
    var pathList = docRef.pathItems;
    // Loop through this list of objects
    for (var h = 0; h < pathList.length; h++)     {
         // Change the property values
         pathList[h].filled = false;
         pathList[h].stroked = true;
         pathList[h].strokeColor = reg.color;
         pathList[h].strokeWidth = 2;
    // Set a variable to the document groups collection
    var groupList = docRef.groupItems;
    // Loop through this list of objects
    for (var i = 0; i < groupList.length; i++)     {
         // Re-use variable for the groups path items collection
         pathList = groupList[i].pathItems;
         // Loop through this list of objects
         for (var j = 0; j < pathList.length; j++)     {
              // Change the property values
              pathList[j].filled = false;
              pathList[j].stroked = true;
              pathList[j].strokeColor = reg.color;
              pathList[j].strokeWidth = 2;
    app.redraw();

Maybe you are looking for