Route not showing up in routing table.

I have my core switch connecting to my router which connects to our MPLS provider. My router has a BGP default route going to the MPLS provider edge router B*   0.0.0.0/0 [20/0] via 172.30.252.78, 1w4d .... This route is not showing up in my core switch. Shouldnt it show up as an eigrp ex default route? Can anyone assist me? my routing table for each device is below. Thank you!
Router
USJONELAWTN01R#sho ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route
Gateway of last resort is 172.30.252.78 to network 0.0.0.0
     68.0.0.0/32 is subnetted, 1 subnets
S       68.142.83.236 is directly connected, Null0
     198.63.196.0/32 is subnetted, 1 subnets
S       198.63.196.103 is directly connected, Null0
     64.0.0.0/32 is subnetted, 1 subnets
S       64.234.192.40 is directly connected, Null0
     172.26.0.0/16 is variably subnetted, 3 subnets, 2 masks
D       172.26.82.0/24 [90/28416] via 172.28.82.10, 1w5d, GigabitEthernet0/1
                       [90/28416] via 172.28.80.10, 1w5d, GigabitEthernet0/0.1
                       [90/28416] via 172.28.80.9, 1w5d, GigabitEthernet0/0.1
D       172.26.83.0/24 [90/28416] via 172.28.82.10, 1w5d, GigabitEthernet0/1
                       [90/28416] via 172.28.80.10, 1w5d, GigabitEthernet0/0.1
                       [90/28416] via 172.28.80.9, 1w5d, GigabitEthernet0/0.1
D       172.26.80.0/23 [90/28416] via 172.28.82.10, 1w5d, GigabitEthernet0/1
                       [90/28416] via 172.28.80.10, 1w5d, GigabitEthernet0/0.1
                       [90/28416] via 172.28.80.9, 1w5d, GigabitEthernet0/0.1
     172.28.0.0/16 is variably subnetted, 4 subnets, 2 masks
C       172.28.176.0/23 is directly connected, GigabitEthernet0/0.6
C       172.28.80.0/23 is directly connected, GigabitEthernet0/0.1
C       172.28.82.0/23 is directly connected, GigabitEthernet0/1
D       172.28.80.20/32
           [90/30720] via 172.28.176.3, 1w5d, GigabitEthernet0/0.6
           [90/30720] via 172.28.82.3, 1w5d, GigabitEthernet0/1
           [90/30720] via 172.28.80.3, 1w5d, GigabitEthernet0/0.1
     172.30.0.0/16 is variably subnetted, 6 subnets, 2 masks
C       172.30.252.78/32 is directly connected, Multilink1
C       172.30.252.76/30 is directly connected, Multilink1
D       172.30.252.114/32
           [90/3415808] via 172.28.176.3, 4d00h, GigabitEthernet0/0.6
           [90/3415808] via 172.28.82.3, 4d00h, GigabitEthernet0/1
           [90/3415808] via 172.28.80.3, 4d00h, GigabitEthernet0/0.1
D       172.30.252.112/30
           [90/3415808] via 172.28.176.3, 4d00h, GigabitEthernet0/0.6
           [90/3415808] via 172.28.82.3, 4d00h, GigabitEthernet0/1
           [90/3415808] via 172.28.80.3, 4d00h, GigabitEthernet0/0.1
D       172.30.254.24/32
           [90/156160] via 172.28.176.3, 1w5d, GigabitEthernet0/0.6
           [90/156160] via 172.28.82.3, 1w5d, GigabitEthernet0/1
           [90/156160] via 172.28.80.3, 1w5d, GigabitEthernet0/0.1
C       172.30.254.25/32 is directly connected, Loopback10
C    192.168.202.0/24 is directly connected, GigabitEthernet0/0.1
     10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
S       10.192.254.0/24 [1/0] via 172.28.82.10, GigabitEthernet0/1
S       10.201.0.0/16 [1/0] via 172.28.82.10, GigabitEthernet0/1
S       10.200.1.0/24 [1/0] via 172.28.82.10, GigabitEthernet0/1
C    192.168.203.0/24 is directly connected, GigabitEthernet0/0.1
C    192.168.51.0/24 is directly connected, GigabitEthernet0/0.1
B*   0.0.0.0/0 [20/0] via 172.30.252.78, 1w4d
B    200.200.0.0/16 [20/0] via 172.30.252.78, 1w4d
B    201.1.0.0/16 [20/0] via 172.30.252.78, 1w4d
B    172.16.0.0/12 [20/0] via 172.30.252.78, 1w4d
B    198.30.0.0/16 [20/0] via 172.30.252.78, 1w4d
B    192.168.0.0/16 [20/0] via 172.30.252.78, 1w4d
Core Switch
TNLAW-TN1COREA# sho ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route
Gateway of last resort is 10.192.61.1 to network 0.0.0.0
     172.26.0.0/16 is variably subnetted, 3 subnets, 2 masks
C       172.26.82.0/24 is directly connected, Vlan601
C       172.26.83.0/24 is directly connected, Vlan603
C       172.26.80.0/23 is directly connected, Vlan602
     172.28.0.0/16 is variably subnetted, 4 subnets, 2 masks
D       172.28.176.0/23 [90/28416] via 172.28.82.3, 7w0d, Vlan2
                        [90/28416] via 172.28.82.2, 7w0d, Vlan2
                        [90/28416] via 172.28.80.3, 7w0d, Vlan1
                        [90/28416] via 172.28.80.2, 7w0d, Vlan1
C       172.28.80.0/23 is directly connected, Vlan1
C       172.28.82.0/23 is directly connected, Vlan2
D       172.28.80.20/32 [90/28416] via 172.28.82.3, 7w0d, Vlan2
                        [90/28416] via 172.28.80.3, 7w0d, Vlan1
     172.30.0.0/16 is variably subnetted, 6 subnets, 2 masks
D       172.30.252.78/32 [90/3413504] via 172.28.82.2, 1w4d, Vlan2
                         [90/3413504] via 172.28.80.2, 1w4d, Vlan1
D       172.30.252.76/30 [90/3413504] via 172.28.82.2, 1w4d, Vlan2
                         [90/3413504] via 172.28.80.2, 1w4d, Vlan1
D       172.30.252.114/32 [90/3413504] via 172.28.82.3, 4d00h, Vlan2
                          [90/3413504] via 172.28.80.3, 4d00h, Vlan1
D       172.30.252.112/30 [90/3413504] via 172.28.82.3, 4d00h, Vlan2
                          [90/3413504] via 172.28.80.3, 4d00h, Vlan1
D       172.30.254.24/32 [90/130816] via 172.28.82.3, 7w0d, Vlan2
                         [90/130816] via 172.28.80.3, 7w0d, Vlan1
D       172.30.254.25/32 [90/130816] via 172.28.82.2, 7w0d, Vlan2
                         [90/130816] via 172.28.80.2, 7w0d, Vlan1
D    192.168.202.0/24 [90/28416] via 172.28.82.3, 7w0d, Vlan2
                      [90/28416] via 172.28.82.2, 7w0d, Vlan2
     10.0.0.0/8 is variably subnetted, 4 subnets, 3 masks
S       10.192.254.0/24 [1/0] via 10.192.61.1, GigabitEthernet3/47
S       10.201.0.0/16 [1/0] via 10.192.61.1, GigabitEthernet3/47
S       10.200.1.0/24 [1/0] via 10.192.61.1, GigabitEthernet3/47
C       10.192.61.0/28 is directly connected, GigabitEthernet3/47
D    192.168.203.0/24 [90/28416] via 172.28.82.3, 7w0d, Vlan2
                      [90/28416] via 172.28.82.2, 7w0d, Vlan2
D    192.168.51.0/24 [90/28416] via 172.28.82.3, 7w0d, Vlan2
                     [90/28416] via 172.28.82.2, 7w0d, Vlan2
S*   0.0.0.0/0 [250/0] via 10.192.61.1, GigabitEthernet3/47

Hello,
The core switch has got a static default route pointing to 10.192.61.1. It has got a better AD value than the EIGRP routes.
Even if you are redistributing the BGP routes into EIGRP, EIGRP default route will not make it to the routing table because of the higher AD value than the static route.
However, you can view that it the EIGRP topology table. Check 'Sh ip ei topo'.
Krishna

Similar Messages

Google maps is not showing roads and routes when I try to get directions

When using google maps to get directions the roads disappear and routes do not show.

But are you shutting down Firefox properly...
:see my answer in https://support.mozilla.com/en-US/questions/860929

Production Order routing not showing process time

Dear Guru's
After creating production order , routing is not showing processing time, though its maintained in the standard values. What could be the problem?
Thanks in advance.
Regards,
PPQMUSER

Hi,
U should check ur processing formula used in work centre. If it is correct and your routing is showing correct data then do READ PP MASTER DATA in your production order.
It will help you.
Regards,
Alok Tiwari

Power Pivot Slicer options not showing in the Pivot Table Field list

Excel 2013. In all the tutorials I watch when you create a Pivot Table using Power Pivot there are Slicer options in the
Pivot Table Fields list. Slicer Horizontal, Slicer Vertical These do not show for me. I see Filters, Value, Row, Column only. Is there a setting I need to turn on? When I click on PowerPivot
at the top, the first icon on the bar is Manage Data model, not Powerpivot as I have seen on some of the youtube tutorials. Thank you in advance.

Thank you for trying but it's not what I am after. I understand how to use Slicers with pivot tables. My question relates to Pivot Tables created using PowerPivot. Directly under the Pivot Fields list on the right is a section where
you choose what you want to pivot i.e Filters, Values, Rows, Columns. These are standard with any pivot table. When I watch videos on PowerPivot there are 2 additional options in the section. Slicer Vertical, Slicers Horizontal.
The video comments they only show in when creating a pivot table using PowerPivot. These 2 options are not there for me. I don't know why. It maybe the version of office I am using which is Microsoft Office Plus 2013. I'd like them
included. Appreciate you taking the time to help.

IE 10 not showing some text on Table

Some of the texts are not shown on IE10 mode. This occurs on random cells. On page refresh also this occurs again on any other cells randomly. But these texts are shown while selecting IE9 mode on Internet Explorer.
I can see those data on source code. And if I copy and paste on Notepad that table data I can the text for all the cells.
How to solve this. I need solution for this as soon as possible.
I have used the following code for the above table:
<table cellspacing="0" border="1" style="border-collapse: collapse;" align="center">
    <tr class="gr_hdr">
        <td>
            Meter
        </td>
        <td>
            Field
        </td>
        <td>
            Value
        </td>
    </tr>
    <asp:Repeater ID="DataRepeater" EnableViewState="false" runat="server">
        <ItemTemplate>
       </ItemTemplate>
    </asp:Repeater>
</table>
CSS used
.gr_hdr
    background-image: url(../img/grd.gif);
    font-family: Verdana, Arial, Helvetica, sans-serif;
    font-size: 11px;
    font-weight: bold;
    color: #660000;
    background-color: #845446;
    height:24px;
    text-align: center;

Hi Rob,
Thanks for the response.
I checked and the Trace Styles tab does not show the cell having "display:table-cell" style.
This web application uses a standard css to define styles for a <td> tag as such:
td {font-family: Arial; font-size: 8pt;}
if I add the style you have mentioned as such
td {font-family: Arial; font-size: 8pt; display:table-cell;}
It still does not show up when I select the <td> cell and check the "Trace Styles" tab.
Am I using the "display:table-cell" incorrectly? Where else should I specify it?
The HTML for the whole web page is huge so I am including just the HTML of the affected part of the page:
<tr>
<td align=center>
<table border=1 bgcolor=white cellspacing=0 cellpadding=2 width=100%>
<tr valign=bottom class=tableTitle2>
<td rowspan=3 width=20% colspan=2>Queue Name</td>
<td colspan=3 rowspan=2 width=35% align=center>Applications</td>
<td colspan=5 align=center width=45%>Pend Assignments</td>
</tr>
<tr valign=bottom>
<td colspan=3 align=center><b>Assigned To Queue</b></td>
<td colspan=2 bgcolor=white align=center><b>Assigned From Queue</b></td>
</tr>
<tr valign=bottom class=darkHeader>
<td align=center >Unassigned</td>
<td align=center >To Me</b></td>
<td align=center >To Others</td>
<td align=center>Unassigned</td>
<td align=center >To Me</td>
<td align=center>To Others</td>
<td align=center>By Me</td>
<td align=center >By Others</td>
</tr>
<tr>
<td
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=19&rnd=560d1478-2c5a-493a-a18e-034ad6599405'>
<b>Enrollment</b></a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=19&rnd=790040a0-570c-4429-91c0-7a9d030a174e'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=19&category=1&rnd=d03bedaa-cb47-40ed-9fce-f04939b2d60e'>
19</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=19&category=3&rnd=638bea64-72a1-483e-9081-1ad803cc1e7a'>
155</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=19&category=7&rnd=cf5f4985-7a6e-4319-a104-f6beb9ecca59'>
1</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=19&category=8&rnd=1ed0ee0a-6d8f-497e-b1eb-4a15b008df6c'>
113</a>
</td>
</tr>
<tr>
<td
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=22&rnd=38f71731-0658-4f90-b899-031f5cc3e225'>
<b>Introduction Call</b></a>
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=22&rnd=bbbb06e5-8bd1-401a-8c32-881b71eac952'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=22&category=1&rnd=0e871bc7-64bf-4ddf-877a-96a48328e604'>
14</a>
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=22&category=3&rnd=d2a512eb-aa5c-4b72-9f9f-87b52bc6aebe'>
57</a>
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
</tr>
<tr>
<td
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=27&rnd=30b5f89c-be4b-4525-b3ee-0afbe4df85c7'>
<b>Tax Set-Up</b></a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=27&rnd=72873a74-75ad-4a6a-bca4-a8de0b5165e5'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=27&category=1&rnd=91be337e-3232-4a89-87a9-5b3ba1ed5ccf'>
3</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
</tr>
<tr>
<td
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=17&rnd=8153a964-1403-4345-ae67-f0ebf263b981'>
<b>Implementation</b></a>
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=17&rnd=3d532f7b-3ed7-4e2a-8056-af32acd0ce44'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=17&category=3&rnd=697c0e1a-2d28-42e8-a204-5b1f3a70262f'>
112</a>
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=17&category=7&rnd=15c11294-cd7f-4cac-add6-2dd27c99b1fb'>
3</a>
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
</tr>
<tr>
<td
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=28&rnd=6d57a566-07d0-45ec-9f35-e4ad1bd15e60'>
<b>Tax QA</b></a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=28&rnd=818cad70-e7e0-47fb-a4d0-c30170dfeb24'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=28&category=1&rnd=2945c092-c06e-4e33-85e6-f5967efa5256'>
5</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=28&category=3&rnd=b9538200-588f-4385-86fe-7d33f2841072'>
11</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=28&category=7&rnd=72c3073f-cc11-42b2-9164-d98ab4e1858a'>
1</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=28&category=8&rnd=453825e3-db85-44d4-87b5-c5c970c8c9d4'>
3</a>
</td>
</tr>
<tr>
<td
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=13&rnd=fd8957c6-1ae2-4aa7-8fc0-a88be1e99620'>
<b>Implementation QA</b></a>
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=13&rnd=95a425a7-2271-4fec-aa86-0910f9b5928b'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=13&category=3&rnd=847fbc95-0660-45b3-9ee2-0eb85b362efb'>
601</a>
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
</tr>
<tr>
<td
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=14&rnd=2499ce88-8f1f-4cd5-875e-4d482ad127ea'>
<b>1st Processed</b></a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=14&rnd=352273f4-976e-43cb-9c3e-a35a81ae8d4e'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=14&category=3&rnd=6be1692f-cbb0-48c3-baf4-f17b80e04d81'>
420</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=14&category=8&rnd=2b98e623-c93c-4532-ab26-5c4abc34fde2'>
3</a>
</td>
</tr>
<tr>
<td
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=12&rnd=e8a8dfec-fdee-40da-b7d9-9c2a803dd039'>
<b>1st Processed QA</b></a>
</td>
<td align=center
bgcolor=#EDEDED
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=12&rnd=c2b39342-cc40-4253-ac8a-1cf16397d24c'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
bgcolor=#EDEDED
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
<td align=center
class='otherGrey'
>
0
</td>
</tr>
<tr>
<td
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=34&rnd=2e37d520-5ec1-435f-93f5-7c1a64fe2ee8'>
<b>Account Manager</b></a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camQueueUserAdmin?camQId=34&rnd=cea88295-1b5a-4948-b79e-b82c1919de94'>
<img src=https://Some.Corp.Url/images/cam/queueadmin.gif align=absmiddle border=0 alt='Maintain Users in this Queue'></a>
</a>
</td>
<td align=center
>
<a href='https://Some.Corp.Url/cam/camAppPendQList?camQId=34&category=1&rnd=f618b964-5a6f-4b0c-9ff2-a2b614c847aa'>
22</a>
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
<td align=center
>
0
</td>
</tr>
</table>
</td>
</tr>
Its always the <td> tags with the numeric data in them that disappear.
Please let me know if I should declare the style for every <td> tag? I was under the impression that this style was only relevant for displaying tabular data within <div> tags.
Besides this, is there anything else I can do to mitigate this issue? It is quickly escalating with our customers.
Thanks for all your help.
Ahmad

LST No/CST No is not showing in Excise Header table

Dear All,
I am facing one problem that i maintained the LST No.(J_1ILSTNO) and CST No(J_1ICSTNO) in transaction J1ID -customer master excise additional data against the customer code but when i am creating the Excise invoice for that customer then in excise header table (J_1iexchdr )the LST No(LSTNO)/CST No (CSTNO) is not showing or not getting updated ?
any reason why it is not getting updated in excise header table?
warm regards
ravi k

HI
it was a typo error the table is J_1IEXCHDR
check the customer master and also check whether they are coming in excise invoice
also check this Note 1048759 - CST, LST, PAN no. of customer not filled in J1IIN
regards

E3000 as an access point with an E3200 as the primary router not showing all connected devices

I recently rewired my home with cat 6. All network and telephone comes in to the basement. While most devices in the home were converted to LAN connections a few remain WiFi connected. The connections are as follows:
Cable modem -> E3200 ->High Speed Switch <--> E3000.
I purchased the E3200 to be the primary router. I'm using both 5.0 and 2.4 ghz connections. I set up my (existing) E3000 as an access point (AP) according to these instructions. I used the LAN-LAN setup so that all devices would be on the same network. Both E3200 and E3000 are at the latest firmware level. Both use the same SSIDs, one each for 5ghz connection and a second for 2.4 ghz connection. Almost everything is working but there are a few nagging issues.
1) A smart phone connected wirelessly to the AP shows as a LAN connection when viewing the E3200 DHCP client list
2) I set up a DHCP reservation for my network attached printer on the E3200. When it connects via the AP it is not assigned the predefined IP address
3) I can see the network attached printer on the E3000 MAC filter list but I can't see it when viewing DHCP clients or MAC wireless clients from the E3200 even though the printer is attached and working correctly.
I can understand the reasons for issue 1 but it seems that a client attached to a wireless AP should also show as wireless to the main router.

Well, let me know what IP addressess you have assigned to the network devices? Second if you remove the switch from the network (between E3200 and E3000) does the issue still persist... Once powercycle the whole network and then check whether it happens or not.

WRT54G Problem- SSID not showing in list & router not sending correct IP address

Everthing was humming along. Comcast Internet = fine. WRT54G router, several XP Pro/SP 3 computers, 1 Powerbook + wireless printers. etc = fine. PCs find network SSID and auto-connect without fail.
Then, Comcast Internet down. Reboot everything. Network back up. Computers then get wrong IP Address or do not see SSID. (No config changes on computers.)
So I:
1. Reinstall WRT54G firmware (v8) - no change.
2. Install new fresh WRT54G - using CD to install - no change
3. Update firmware in router used in #2 - no change
4. Complete reset cycle and reinstall -no change.
5. Repeat same reset with original router -no change
6. Using static IP address/default gate way/DNS address - PC finds and connects to SSID but does not access Internet.
Result - no computers find SSID. (SSID is hidden.) Don't find it when it's not hidden either.
Ethernet cabled PC works just fine. Gets correct IP Address & Internet access is fine.
Cable modem = Motorola Surf Board. No physical locations of any omponent has changed.
Is it possible that both WRT54G's are not working?
Is it somehow a Comcast problem?
Should I try some other router settings?
Many thanks!

Thanks. These are great instructions and quite useful for setup. Unfortunately, my problems seemed much more complex.
In the end, I redidi all the networking from scratch from the router through all the connected devices. Finally got things back up. I don't know how, but the Comcast failure seemed to corrupt lots of the settings even if they all looked OK.

Host not showing up in ARP table

Hi,
I am having an interesting/weird problem with one of my Catalyst 6509 switches.
The setup is as follows:
HostA - Switch1 - Switch2 - HostB
There is routing in place for HostA to reach HostB and vica versa.
I am testing this using ICMP. There is nothing blocking ICMP traffic on any of the devices.
Problem in question: I can only ping HostB from HostA (or Switch1) if HostB is found in the ARP table of Switch2. Pretty normal you might say since we need Switch2 to route/switch the packet to HostB and that will of course only happen if the ARP table is populated.
But what happens is the following:
I ping from HostA to HostB. It fails. I check Switch2 and I see that HostB is nowhere to be found in its ARP table.
Next I ping HostB from Switch2 (5 packets). First packet fails, last 4 I get a reply. I check and see that now HostB is to be found in the ARP table of Switch2.
Now I ping HostB from HostA and it works fine.
This behaviour is happening for all hosts in the subnet (VLAN) of HostB. I cannot reach them until I ping them from Switch2, after which they're in the ARP table and everything works.
Maybe it something different than the ARP table not being populated all together, but that is for now all I noticed. Does this problem ring a bell with anyone. And is there a fix?
It looks to me like Switch2 is malfunctioning, although I have no idea what is. Furthermore this apears to be working ok for a lot (read: all) of the other VLANS on Switch2.
Anyway. I'd love some help in troubleshooting this one.
kind regards,
Kevin

This goes back to the way switches (or bridges) work. They have to see a frame from an end device to know its MAC address and once they see it they add an entry in their CAM (or MAC) table. The entry basically tells the switch that a specific MAC is reachable via a particular port and this is meant to prevent subsequent flooding of unicast frames. In short an end device needs to send at least one frame for the switch to 'see' it. Another point to remember is that each entry in the CAM table has an age associated with it and if a switch does not see subsequent frames from that host it will age out the entry and start flooding all frames destined to this MAC address until it is learnt again (and learning is done only when the owner of the MAC starts to communicate again).
Kevin,
Can you please explain your topology in a bit more detail? I am looking for information like what is the default gateway of each VLAN, how are the VLANs spread across the two switches, any HSRP configurations and if yes who is the active for what VLAN, routing between switches, etc. This will help us troubleshoot the problem in a more effective manner.

Specific Model not showing rows in a table in a column of a table

Hello,
Fairly simple issue here (I think):
I have a table bound to a global model and its rows bound to "/items"
I then have a column within that table which has a valuehelpfield that pops open a dialog with a table.
This tables rows inside the dialog are bound to a temp model. Now I know this temp model has the correct data and format and I do not get a "no data" messages when I bind it's rows to the node on the temp model, and to double check that I tried binding it to an incorrect node and it did say "no data" and I tripple checked by getting the jsonstring of the model and it's exactly how it should be.
Here is the code:
oTable.addColumn(new sap.ui.table.Column({
            label: new sap.ui.commons.Label({
                text: "Shop",
                required: true
            width: "200px",
            template: new sap.ui.commons.ValueHelpField({
            value:"{shopdesc}",
             valueHelpRequest: function(oEvent){
             var locModel = oTable.getModel();
             var rowContextPath = oEvent.getSource().getBindingContext().getPath();
             var oRowObj = oEvent.getSource().getBindingContext().getObject();
          var oDataOld = sap.ui.getCore().getModel().getData();
         var tempModel = new myJSONModel;
      tempModel.setData({
      shops: []
sap.ui.getCore().setModel(tempModel, "tempModel");
         tempModel = sap.ui.getCore().getModel('tempModel');
            d = tempModel.getData();
            arr = d.shops;
          var shops = oDataOld.shops;
             for (var i = 0; i < shops.length; i++) {
                 if (shops[i].area == oRowObj.area) {
                         arr.push(shops[i]);
             var oValueHelpDialog = new sap.ui.commons.Dialog(
                        { modal: true,
                            title: "Select a Shop",
                            closed: function (oEvent) {
                            var oContext = oTableJobs.getContextByIndex(oTableJobs.getSelectedIndex());
                            if (oContext) {
                           var oSel = oContext.getModel().getProperty(oContext.getPath());
                         locModel.setProperty(rowContextPath + "/shop", oSel["shop"]);
                         locModel.setProperty(rowContextPath + "/shopdesc", oSel["shopdesc"]);
             var oTableJobs = new sap.ui.table.Table({
                 visibleRowCount: 15,
                 firstVisibleRow: 1,
                 selectionMode: sap.ui.table.SelectionMode.Single,
                 width : "300px"
             var oOkButton = new sap.ui.commons.Button({
                 text: "OK",
                 press: function (oEvent) {
                   oEvent.getSource().getParent().close();
             oTableJobs.addColumn(new sap.ui.table.Column({
                 label: new sap.ui.commons.Label({text: "shop"}),
                 template: new sap.ui.commons.TextField().bindProperty("value", "shop"),
                 editable:false,
                 width: "100px"
             oTableJobs.addColumn(new sap.ui.table.Column({
                 label: new sap.ui.commons.Label({text: "Shop Description"}),
                 template: new sap.ui.commons.TextField().bindProperty("value", "shopdesc"),
                 editable:false,
                 width: "300px"
             var jsonString = tempModel.getJSON();
             alert(jsonString);
                 oTableJobs.bindRows("tempModel>/shops");
                 oValueHelpDialog.addButton(oOkButton);
                 oValueHelpDialog.addContent(oTableJobs);
                 oValueHelpDialog.open();
        var oModel = sap.ui.getCore().getModel();
        oTable.setModel(oModel);
        oTable.bindRows("/items");
Any help would be appreciated, I can't see what's wrong here, all seems fine to me! Thanks!

HI Bob
I briefly scan thru your code and spotted one common issue. When we are binding property, we need to include the model name. e.g.
template: new sap.ui.commons.TextField().bindProperty("value", "shop"),
should be
template: new sap.ui.commons.TextField().bindProperty("value", "tempModel>shop"),
-D

Mapping not showing up for Oracle Tables

I'm just getting started with OWB after attending a class and am using the textbooks received with the course. I've created a project with modules for different schemas each containing several Oracle tables. I don't get the Mapping for either of these modules nor can I use the configure option to create Mappings. Does anyone know what I can do?

For our OWB projects, we create all modules as target
modules. It is probably a good idea not to use
source modules since OMBPlus does not recognize them.Hi,
I think you may be missing the essential difference between source and warehouse modules. A source module is just that, a place where definitions of he source data is held, which is that data outside the scope of the warehouse project. As such, it makes no sense for OMBplus to reference this information.
As a practical example, it would make absolutely no sense to run OMBplus against your operational OLTP sytem from which you extract your source data.
The value of source modules is that you can reference this 'remote' data as though it is local data, and because you have its metadata, you can manipulate it and map from it as though it is 'yours', even though it isn't. Further, the Import Metadata Wizard can provide details on source system changes, and you can then analyse the impact.
But I'm still puzzled about automatic reconciliation. Please see "Metadata Import and Reconcile" for further details. (52 views and no replies? Surely someone knows how to do this!).
Cheers,
Donna

Subject Area not showing for Single Logical Table Repository Schema

Hi
I'm trying to create a very simple OBIEE repository schema for a sales proof of concept. The schema consits of a single physical table, single BMM (logical) table and a single presentation table.
I have created all the layers OK. However, when I check for global consistancy i get an error message 'Logical table SALES_POC does not join to any other logical table'. Now i understand this error, but in this case this is how the design is intended. However, if ignore this error i'm not seeing the new subject area after bouncing BI server & BI presentation services.
Anyone know a way round this, or do i need to have at least 2 logical tables?
Thanks
James

Yes I think RPD is in the correct folder & NQSConfig.INI is set correctly.
RPD is called ethreeCustomv1.RPD & saved in /ora/biee/10.1.3.4/OracleBI/server/Repository
NQSConfig.INI has the following definition:
[ REPOSITORY ]
BIEE = ethreeCustomv1.rpd, DEFAULT;
[ CACHE ]
ENABLE = NO;

Apex_plsql_job.submit_process job not showing up in apex_plsql_jobs table

Hello ghurus,
I am running APEX 3.1 on Oracle 10g 10.2.0.1 and am trying to run a potentially long running procedure in the background so the user doesn't have to sit and watch the hourglass.
The button process has the following code:
DECLARE
return_code NUMBER;
exec_stg VARCHAR2(4000);
squote VARCHAR2(1) := chr(39);
edit_cnt NUMBER;
BEGIN
SELECT COUNT(*)
INTO edit_cnt
FROM edit_history eh
WHERE eh.rept_inst = :f104_curinst
AND eh.rept_time_frame = :f104_curterm
AND eh.submission = :f104_cursubm
AND eh.edit_complete_dtm IS NULL;
univdb.exception_logging.insert_log(0, 'NO SQL ERROR', 'apex_editsubm','count=' || to_char(edit_cnt));
IF edit_cnt = 0
THEN
INSERT INTO univdb.edit_history
(rept_inst,
rept_time_frame,
submission,
audit_id)
VALUES
(:f104_curinst,
:f104_curterm,
:f104_cursubm,
:app_user);
COMMIT;
univdb.exception_logging.insert_log(0, 'NO SQL ERROR', 'apex_editsubm',
'insert row successful');
exec_stg := 'univdb.edit_any_submission(' || squote || :f104_curinst ||
squote || ', ' || squote || :f104_curterm || squote || ', ' ||
squote || :f104_cursubm || squote || ', ' || squote ||
:app_user || squote || ');';
univdb.exception_logging.insert_log(0, 'NO SQL ERROR', 'apex_editsubm',exec_stg);
return_code := apex_plsql_job.submit_process(exec_stg);
univdb.exception_logging.insert_log(0, 'NO SQL ERROR', 'apex_editsubm','return_code=' || to_char(return_code));
commit;
END IF;
END;
The calls to exception_logging write a row to a table so I can see what's happening in the process and I get the following rows writte:
count=0
insert row successful
univdb.edit_any_submission('UNIV', '200701', 'TEF', 'ELSA_LESLIE');
return_code=103
The last message implies to me that the job was successfully submitted but when I query the apex_plsql_jobs table, job 103 does not exist and the procedure never gets executed. The procedure does work when tested outside of APEX.
I checked all of my grants according to the post in this thread and they are all there:
Re: Missing apex_plsql_job in 3.1
Does anyone have a suggestion?
...elsa

Hi Elsa
I am also having similar problems calling the APEX_PLSQL_JOB.SUBMIT_PROCESS as well where it doesn't insert into the APEX_PLSQL_JOBS table.
I also noticed that you used SCHEDULER. One of the challenges we are having is when the user presses the submit button, the browser hangs and doesn't return the result set until the process is complete. This process can take 20 mins before the screen loads saying the process was finished. I have tried used DBMS_JOB as we aren't on 10g and can not use SCHEDULER, but still having that issue where the user has to wait 20 mins before the process finishes.
Did you ever solve that problem where the user clicks the button and then a page is returned immediately while the job is firing away with scheduler
Any help would be great and much appreciated.
Thanks

Plz. help,table does not show value for one field

hi all,
i have a really strange problem , i have a string field in access database that contains the date and time value,this field for some strange reason does not show in my table created through html,
i tried all combination(arranging the fields) ,renaming it w/o help, it shows the value using out.println(but then why is it not showing me in the table???)
plz. help ASAP.
the code is as under
<HTML>
<HEAD><TITLE> LOGGED IN ok</TITLE> </HEAD>
<BODY bgcolor = "yellow">
<%@ page import = "java.sql.*" %>
     <%! // declaring variables
String s = "";
java.sql.ResultSet rs=null,rs1=null,rs2=null;
java.sql.Connection con;
java.sql.Statement stmt,stmt1;
String empId = "",compid ="",calltype ="",probheader="",probdescription ="",probcomment ="",priority ="",a="";
%>
Following are the pending complaints ..
     <TABLE BORDER=1 CELLSPACING=0 CELLPADDING=0 width="100%">
     <TR>
     <TD> ComplainD </TD>
<TD> ComplainId </TD>
<TD> ProbHeader </TD>

</TR>
     <%
     try
     Class.forName("sun.jdbc.odbc.JdbcOdbcDriver");
     java.sql.Connection con = java.sql.DriverManager.getConnection("jdbc:odbc:Driver={Microsoft Access Driver (*.mdb)};" +"DBQ=c:/vishal/HelpDesk.mdb;DriverID=22;READONLY=false","","");
     //java.sql.Connection con = java.sql.DriverManager.getConnection("jdbc:odbc:Portal");
          java.sql.Statement stmt = con.createStatement(java.sql.ResultSet.TYPE_SCROLL_INSENSITIVE,java.sql.ResultSet.CONCUR_READ_ONLY);
          s = "select * from Complains";
     java.sql.ResultSet rs = stmt.executeQuery(s);
                    while(rs.next())
                    //getting data from database
                                                       empId = rs.getString("EmpId");                    // out.print(" " + empId);
          compid = rs.getString("ComplainId");
          // out.print(" " + compid);
          calltype = rs.getString("CallType");
          // out.print(" " + calltype);
                    a = rs.getString("Complaindate"); //problem with this field
out.print(a); // prints value
          %>
                    <TR>
                    <TD> <%=compid %> </TD>
                    <TD> <%=calltype %> </TD>
                    <TD <%=a %> </TD>
                                   </TR>
<%
                    }//while loop
     %>
     </TABLE>
     <%
     }//try
          catch(Exception ep)
          out.println(ep);
          System.exit(1);
%>
</BODY>
</HTML>
value in database is as follows :-
Complaindate
5/18/2003 1:30:27 PM
5/18/2003 7:32:43 PM
5/18/2003 7:34:02 PM
5/18/2003 7:49:19 PM
5/18/2003 7:50:27 PM
5/18/2003 10:49:42 PM
5/18/2003 10:58:24 PM
thanking u ,plz ask if any further clarifications

Hi
I am seeing nothing wrong with ur code..
what about "view source" result.....plz check with that...
whether u r getting all the trs and tds...
revert back on this Issue..
Mars Amutha

:: NWA does not show table view for monitoring reports ::

Hi,
We are facing an issue in one of our portal system.
I click on Portal index page, then I go to Net weaver Administrator --> Monitoring --> Java system reports.
Here I get the resource utilization graphs.
The graphs show proper values however when I click on table view it does not show any value or table at all.
Then I click on Settings button, and click on Persistent radio button.
It asks to enter the number of days for which the the data should be stored.
I gave it as 2 days and click on Apply button.
It shows a message saying "changes would be effective after restarting monitoring service".
However when I go there i.e. NWA --> Administration --> Applications
I get below services
cafruntimemonitoring~ear
com.sap.ip.bi.sdk.monitoring
tclmwebadminmonitoravail~wd
tclmwebadminmonitorcomplib~wd
tclmwebadminmonitorprovider_ear
tclmwebadminmonitorstate~wd
tclmwebadminoverviewmonitoring~wd
tcmonitoringsysteminfo
Would you kindly suggest which service from above list should be restarted ?
Thank you, Regards,
Girish Garje.

I think what is being asked is "How do I expose a database view as a schema table in Configuration Manager?"
This is accomplished by creating a database view within the WCC database schema (and with the WCC schema user as the view owner). The view then will appear as a table in the "table" tab in Configuration Manager.
One caveat in 11g is that the user created by RCU does not have any privileges to read/create views in its own schema. You may need to grant privileges to views for the WCC schema user before this will work.

Route not showing up in routing table.

Similar Messages

Maybe you are looking for