Router/Adapter Setup

Been trying to set up an XP computer as the wireless end of a Router/Adapter connex. Using WRT54G/WMP54G. A Vista system system computer on the wired end. The adapter end pretends that it's connected but cannot access Internet.
Am able to separately connect each computer to the wired end and connect to Internet. Can you help me with the problem?

Wizzard,
Sorry, I'm just above a novice. Does this mean that reinstalling the adapter solve the problem? How do I install only the drivers for it? Sorry for being so slow.
jim201

Similar Messages

Get a blank page when I log in to my WRT54G router's setup page

When I try to log in to my router's setup page, I get a blank screen. My router's address is 192.168.1.1, and when I type that in to my browser's address bar, I do get the log-in prompt. I enter the correct password (leaving the user name field blank), and I get a blank screen. The ensuing page does not show me the various setup parameters.
I have 2 PCs and have encountered the problem in both. On one, I am running Windows 7 and the other is running Vista. I recently upgraded my WinXP machine to Win7 and I did not have the problem on XP.
Can you please help?
Thanks
J

To view the router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
Some Zone Alarm users have reported that adding 192.168.1.1 to their list of "trusted" addresses fixed the problem. This trick might also work with other firewalls.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If you still have trouble, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

FTPs adapter setup on Weblogic Server

Hi,
I am trying to setup ftps adapter for BPEL PM 10.1.2.0.2. running on Weblogic Server 8.1. BPEL does support Ftps for this version but it seems weblogic doesnot support ftps. Will this mean that I cannot set it up on WLS.
I have tired to make changes in weblogic-ra.xml file and included all the params required for ftps adapter setup but I always get an error - connot login, please check username and password.
Please help me on this and suggest if any other alternatives are possible.
Regards
Arvind

Hi,
Any help on this ??
Regards
Arvind Aggarwal

FTP Adapter Setup in WLS Admin Console problem

I have setup filezilla ftp server in my W7 laptop.
user id/password is soa/soa
Have also setup the default folders e:\ftp and has permission to read,write, delete.
I get the following error:
Error An error occurred during activation of changes, please see the log for details.
Error java.lang.NullPointerException
Success Selected Deployments were updated.
FTP adapter Setup:
jndi name: eis/ftp/soaFTP
I have set the properties
host = 127.0.0.1
servertype=win
userid = xyz
password = xzy
I tried to delete and reinstall the ftpadapter.rar file located in the E:\Middleware\SOASuite11gR1PS4\Oracle_SOA1\soa\connectors dir several times. Each time I get the above said error. I was trying to set the plan.xml generated in a folder E:\Middleware\SOASuite11gR1PS4\Oracle_SOA1\soa\connector\ftpadapter.
Any help would be appreciated.

Hi,
It seems your deployment plan got corrupted... Try deleting and reinstall the FtpAdapter from deployments on WLS console... Or edit config.xml, remove the deployment plan tag and restart the server...
Hope this helps...
https://forums.oracle.com/forums/ann.jspa?annID=893
Cheers,
Vlad

Can't access my router's setup page (wrt54g)

I can't access my router's setup page (wrt54g) after setting it up. The router is working fine, but everytime I try to log on at 192.168.1.1 it says the password is incorrect. The first time I set it up I changed the default user name and password and I thought I had just forgot it, so I reset the device. This time I didn't change any of the defaults and I still can't log on. I already had to reset it several times, and it's just annoying. Does anyone knows how to keep it from happening? I thought it could be a firmware problem, but I can't find any downloads for my route'rs version (V8). I'm using a macbook pro, osx 10.9.2.
Solved!
Go to Solution.

I had the same problem.. After trying the userid and password from my previous WRT54G2 without success and admin admin multiple times, I used the "router name" ==> Linksys as the user name and the security code that I used to set up the new router as the password and it let me in.. I was on the phone with LINKSYS technical suport during this 1 hour process and they were as much surprised as I was that this worked.. After gettin on and changing the config, (thanks to Honey), I was able to access the internet from the new E2500 THAT i HAD JUST INSTALLED.. success

Adapter setup

Hi Experts,
SOAP, JDBC and JMS Adapter setup(driver Installation) are comes under Post-Installation step of PI 7.0 or developer needs to install those things?
Regards
Sara

Hi Sara,
Setting up adapters for use comes under post installation.
When there is a need to connect to particular database or message server, then these drivers are installed at the time of requirement either by basis or developer.
Eg. You want to connect to MySql, then the JDBC drivers are installed and the parameters are specified in ID in JDBC Sender/Receiver adapters. But JDBC Adapter is already ready, no need to make additional settings for it.
Regards,
Piyush

Wireless Router Security Setup

Sorry in advance if this is a stupid question but I am fairly new to my mac. (love it by the way)
We have DSL at home and recently bought a Belkin Wireless G router. I put in the cd that came with it and selected the Mac option for install. Now, after this it took only a few seconds and was done. All connected and up and running in nothing flat. My wife was able to connect via her PC laptop no problem.
I want to secure this wireless connection and I can't quite figure out how. Oddly enough there is no Belkin icon for me to click on to get into any properties. When I type belkin into my spotlight search nothing comes up. I assume I should be setting up the security directly on my mac somehow but just not sure how.???
Have tried reading and searching but still can't find anything. Right now I am assuming my question is just too simple so no one else has this problem but I just can't get my pea sized intellect to figure it out.
Thanks All!

Well, you do have Security on your Mac, but what you want is to address the router's Setup page
Run Safari and type this into the url bar...
http://192.168.2.1
You should see a Menu there.
Come to think of it, this is probably the best source on how to...
http://www.portforward.com/english/routers/wireless/routerindex.htm
I think this might be your Router.
http://www.portforward.com/english/routers/wireless/Belkin/F5D7230-4/F5D7230-4in dex.htm
Message was edited by: BDAqua

831 router....'loading cisco router web setup. please wait'

We just received a used 831 from our other office. I put in http://10.10.10.1 then click continue for the language. It comes to a screen that reads: 'Loading Cisco Router Web Setup. Please Wait...' thats as far as it will go. I'm not sure where to start I'm new to cisco routers. I have read the manual that came w/ it but couldn't find out any information. Your help will be greatly appreciated.
Thanks

Hello Brandon,
CRWS is a little bit buggy, try SDM instead, which is supposed to be the replacement for CRWS. YOu can download it here:
http://www.cisco.com/pcgi-bin/Software/Tablebuild/doftp.pl?ftpfile=pub/web/sdm/SDM-V231.zip&swtype=FCS
When asked for a user ID, just use anonymous/anonymous, it will allow the download.
If you cannot download, post your email address and I will send you the file.
You could also try another browser, such as Firefox:
http://www.firefox.com
HTH,
GNT

Can't login to the router's setup page

I setup my brother’s Linksys WRT54G router using NetSet, should I still be able to get into the router's setup page by typing in 192.168.1.1? I haven’t been able to.
Ronnie

I just upgraded to Internet Explorer to IE 7 and the smart application started blocking the access to the http://192.168.1.1. address.
I had enabled the https option in my router and by I using the https://192.168.1.1 URL IE7 complained about how insecure was to access that site but it let me go in.
If you did not enabled the https option in your router, you may try to use some other browser not so protective of the user.
Regards,
Hector

300N Router/Adapter not working with Satellite internet

I had previously SRX200 router and it was working fine with Satellite but recently I bought again 300N router and adapter but it's not working. It give the strong signal for few seconds and drops it rightway. Please let me know if there is something I need to do with settings.
Thanks
Paul

Paul make sure that the firmware of this router is upgraded to the latest version 1.03.0, it resolves a lot of issue.

Router/Adapter Compatibile?

Good afternoon, I have a quick question....I recently upgraded my router from a WRT54G wireless-G broadband router to a WRT300N wireless-N broadband router. On one of my PC's, I have a WMP54G wireless adapter. Do I need to upgrade this adapter to a wireless-N adapter, or it sufficient? I am having trouble getting this PC to identify/connect to the network after upgrading and I am wondering if the router and adapter are not compatible with each other. Thanks in advance for any help you might be able to provide.

try the following wireless settings on the router ,
ssid - any non-linksys name
radio band - wide
n-channel - 9
standard channel - 11
beacon interval - 50
Fragmentation threshold - 2306
RTS threshold - 2307
let me know if these changes work for you or not....
also,the wmp54g should be able to connect to the wireless-n network...there is no compatibility issue

827H router web setup not working

We were having problems with our 827H router, so I decided to reset it to the factory defaults and re-run the quick setup. I've done that before with no problems.
This time, after it loads the configuration in the web setup, it keeps checking the model, IOS version, etc.--over and over again. It won't stop, nor can we exit out of it to get to the quick setup.
Originally the router was connected to a hub. When we couldn't configure it from the web setup, we put the router directly onto a pc with an ethernet cable. We could ping the router. Using the console cable, we are able to see the router's settings. (See attached)
The pc was set to dhcp. The dns was originally set to "Obtain automatically". We also tried to set the dns and the gateway to the router's ip, and added the domain controller's dns as another dns server. Nothing has worked.
Any help will be greatly appreciated.
Thanks!

Your description of the symptoms is quite puzzling as is the console log that you sent. You say that you connected a PC directly to the router. Was that using a cross over Ethernet cable?
You say that when you connected the PC to the router you could ping the router. What IP address was on the PC at that point.
The console output that you included has a kind of garbled output in the show run. It looks as if two things were outputting at the same time. I am not clear if there were actually two things happening together or if the router is really messed up. (Though most of the config that showed up looked reasonable)
I would suggest that you connect to the console port again and capture all of the console output. I would suggest that whle you are connected and capturing output that you power cycle the router (it may be very helpful to see what messages go to the console while the router is booting).
After the router boots again, you may be able to use the web interface. If the web interface does not work you should be able to use the console interface to get a congif that should work basically.
Try these steps and post the output. Maybe then we can find a solution.
HTH
Rick

FTPS file adapter setup fields not visible after SP13 install

After installation of SP13, I was looking for file adapter FTPS setup (fields described in SP13 release notes). I could not see any. It's just like the old adapter.
Java cryptolib is installed, and we checked it is there.
we recycled the whole thing.
Any idea what could be missing ?

Solved. We had applied SP12 file.
Note that this originates from the SP stack download tool.
We had followed the generic download process and it did not contain the SP13 tpz file.
I tried again this morning, when selecting source sp11 target sp13, The selection of packages selects
SAPBASIS12_0-10002900.zip... and not the SP13 one.
Watch out if you move two SP up !
Detailed solution :
Downloaded the SP13 zip file. the following way.
service.sap.com download/entry by app grp/sap content
process integration (XI content)/ XI_CONTENT_SAP_BASIS/ XI_CONTENT_SAP_BASIS_6.40/DB independant/ selected sp13 from the list
Unzipped, and put the tpz file in the import directory
of the repository. file name is XI3_0_SAP_BASIS_6.40_13_02.tpz
Imported it
And it works now
Thanks a lot for your help.

Connect to ISP thru router - new setup

Connecting a new E2100L Linksys router to ISP through DSL modem produces no connection, but I am able to connect to ISP when modem is connected to computer. This is my first router setup and I followed setup dvd. I'm not clear what issue is. I have shut everything down and restarted in order: DSL modem, router, computer as suggested in Documentation with same result.. Router display indicates Power; Internet Connection and connection to Computer 3.
Present internet connection through computer bypassing router. DSL is usually connected manually through the computer . Assistance appreciated.

Searching the forum found your answer easily.
go here. or here.

Won't recognize my router/adapter

I am at a loss as to what to do.
Problem - my desktop will not recognize my wireless Linksys router.
The main computer in the bedroom is hardwired to the cable. My desktop in the living room is on a wireless router, not hardwired. Last night we had to restart the cable modem. The router seems to be working, but my desktop will not access it. Says the adapter is disabled and I cannot find a way to enable it. I was going to uninstall the driver and re-install and it won't find the driver in "add/remove programs" for me to do that.
HELP!!!!!!!!!!!!

If your adapter is disable simply right click on My Network Places, check under LAN see if there is an red X. If yes, right click and select 'enable'.

Router/Adapter Setup

Similar Messages

Maybe you are looking for