Router connection settings.

Hi everyone.
I'm hoping someone can help me with this but my Belkin router suddenly decided to go back to factory defaults and I lost my BT connection.  I got back into the router but went completely blank on the connection settings.. (ppoA/ppoE etc).  Can somone be a complete lifesaver and post ALL the connection settings i'd need to connect my router to BT.
Thank you...
Mark
Solved!
Go to Solution.

Hi Mark.
Is this any good for you:
http://bt.custhelp.com/app/answers/detail/a_id/644/~/how-do-i-configure-my-non-bt-router-to-work-wit...
toekneem
http://www.no2nuisancecalls.net
(EASBF)

Similar Messages

  • TS1398 iPod touch shows router connection but tick box to connect does not appear

    Although it shows the wifi as connected the tick box doesn't appear just the 'spinning circle' showing it is trying to connect.  I've re-set router, network settings, restored ipod and I have other apple devices happily connected.  Model is brand new 4 32GB with latest software.  Now thinking it's a fault.

    Although it shows the wifi as connected the tick box doesn't appear just the 'spinning circle' showing it is trying to connect.  I've re-set router, network settings, restored ipod and I have other apple devices happily connected.  Model is brand new 4 32GB with latest software.  Now thinking it's a fault.

  • Belkin wireless router connected but browser could not find the host server

    my new roommate has a belkin n wireless router connected to a cable modem which functions perfectly on her pc laptop. i am trying to connect my MacBook Pro to the router using her WEP password. this all works fine and my System Preferences/Network/Status shows that AirPort is connected with full strength, but i cannot load any web pages (i have not yet been able to load any pages at all using this router). the page load error reads "Firefox can't find the server at www.cnn.com" and "The browser could not find the host server for the provided address".
    I spoke with Belkin support and they say the router is functioning properly, that is a problem with my mac.
    When I go to Network Diagnostics, the status shows all green and says "This computer's Internet connection appears to be operating normally. Are you sure you want to use Network Diagnostics?
    Could this be a firewall issue? A couple people have suggested that, but I'm not sure how to fix that.
    I have tried rebooting the router and cable modem, rebooting the mac, etc.
    any ideas on what settings i may need to investigate??
    thank you!
    Message was edited by: photoeyeseattle

    photoeyeseattle wrote:
    how do I know if the router has useful DNS servers? i am looking at the settings of the router on the pc that is online.
    Somewhere in the settings of the router should be the DNS servers that it is using. Since the router is offering via DHCP to do DNS translation for your Mac, it must have useful DNS servers listed.
    There are "public" DNS servers. I have no experience with it, but this Web page describes one from Google:
    http://code.google.com/speed/public-dns/
    Supposedly Google has a DNS server at IP addresses 8.8.8.8 and 8.8.4.4 that you might try. Since the DNS server setting on your Mac is grayed out, as a test you might try noting the setting in the "TCP/IP" tab of your AirPort connection item of the Network panel of System Preferences. Then switch from "Using DHCP" to "Manually", fill in the values you just noted, switch to the DNS tab and fill in Google's DNS addresses, and see if things work better.
    do you have any other suggestions of where to seek help???
    Perhaps a Belkin discussion group?

  • HT4197 router connection on ipod touch

    HOW TO GET ROUTER CONNECTION ON MY IPOD TOUCH

    Does the iPod connect to other networks?
    Does the iPod see the network?
    Any error messages?
    Do other devices now connect?
    Did the iPod connect before?
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • YouView and router connection needs manual restart...

    Hello
    We got YouView in order to watch MotoGP.  We record the races in order to watch the the recodring in the evening.
    If the connection between the router and the YouView box drops out, it will not automatically reconnect.  We have to do it manually.  If this occurs when we are out of the house, then the race is not recorded.
    We spoke to tech support.  They advised a hard reset (which wiped everything we had already recorded) and were assured this would fix the problem. However, it happened again at the weekend.
    Any advice?  Thank you

    Hi,
    Could you try setting the box to connect manually instead of auto and see how you get on?
    It's quite easy to do,
    head into the box setting and look for the connection settings (make sure the box is back online before you do this as it will make it really easy)
    change the setting from auto to manual, you will see th IP, subnet etc already filled out, just use whats there and click through.
    this should make the box save and connect and hopefully not need to be restarted to re-gain connection and hopefully motogp heaven will be restored - fingers crossed
    you'll find the settings in the youview buttion, settings, network and internet
    cheers
    s

  • E1200 Router Connecting Dlink DIP-714P+

    Dear All,
    I am replacing old D-Link DI-714P+ router with E1200.
    The old configuration was a printer connecting to D-Link router, and allow for wireless printing.
    Therefore, may I know how do I configure E1200 so that I still can print wirelessly, while connected to E1200 network.
    Assuming the printer still connected to Dlink router, can we print to E1200 then bridge to Dlink ?
    Thank you.
    regards,
    Chong KK

    If you will replace the old router with the E1200 you simply need to configure the router to work with the modem and setup the wireless settings using the CD. If the printer is connected wired to the Dlink router you simply need to disconnect it from the Dlink and connect it to the E1200 router. After doing that the printer should work and you should be able to do wireless printing. However if the printer is wireless capable and you want to connect that wirelessly to the E1200, then you will need to setup the wireless printer to connect to the wireless settings setup for the E1200 router (you can refer to your printer documentation for that).
    Now if you will leave the Dlink router connected and if you just want to cascade the E1200 router to it then there is a different configuration for that. Base on my understanding you want to leave the printer connected to the dlink and you would like to connect wirelessly to the E1200 router right? Then you need to connect the E1200's ethernet port (one of the yellow ports) to the Dlinks ethernet port as well. This is called LAN to Lan Connection. To know how to do that then click on the link below:
    Cascading (Connecting) a Linksys router to another router
    After doing it you can then Configure the wireless settings of the E1200 manually since you cannot setup the router using the CD with LAN to LAN configuration.
    Configuring the wireless security of your Linksys Wireless-N router through the web-based setup page

  • My iPad disconnects everyone else on the router when in use. It actually kicks off everyone else that is using the same router connection periodically.

    Yes. Not that my iPad gets disconnected, it actually might be causing everyone else to disconnect from the router, including itself.
    Whenever I connect my router to this wifi at work or home at periodic intervals it actually causes everyone, including wifi and 'hard-line' users to receive no connection to the local network and internet.
    When the iPad stops connecting to the wifi, the problem stops for the duration it stays off, Tested it at durations of no iPad connection of 4 hours with no problems. And when connected it causes everyone on the network to drop (for all users) every 5-15 minutes.
    Why does ithis happen and how do I make it stop?

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • WRT54GS router connected, but not detected.

    I have my WRT54GS wireless router connected just like the Easylink setup guide told me to. It goes through the steps up to the point that it tells me to verify that certain lights are on. They are, so I click next. Here's my problem. On the next step, the computer attempts to detect the router, but fails. I can still connect to the internet through the router on my wired connection. On my wireless conection to my PS3, it obtains an IP address, but can't connect. On my wireless connection to my other computer, it finds the network, but can't connect.
    I called Linksys tech support and was told it had something to do with my modem and I had to call my ISP. I called my ISP and they said it was a problem with the router.
    I know none of the hardware is faulty, because it worked when the computers were in opposite positions. That leads me to believe it is some setting on this computer, but I have no idea what it could be.
    Can someone help?

    Access the setup page of the router by launching an
    Browser and type on the address bar, 192.168.1.1 and press enter. When
    it prompts for the username and password, leave the username field
    empty and provide password as "admin" (Without quotes)
    click on ok.
    On the main setup page the ""Internet Connection Type"" should be
    on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
    button.
    Now click on the sub tab ""MAC address clone"".
    - Click on enable
    Click Clone & click save settings
    Check WAN Ip on Status page of router ....
    If getting Valid Ip .... try going online
    If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

  • How to use JNDI datasource instead of database connection settings JDev 10g

    Hi,
    In order to use the different database from other environments, we are not able to use the JNDI datasource configuration settings, all the time need to configure the database connection settings from JDeveloper by changing the database connectivity settings in the JDeveloper for each environment separately, need a solution on how to make the database connectivity unique using the JNDI datasource name for all the environments for database connectivity settings through the application server console rather than changing the database adapter configuration in JDeveloper.
    Please provide the update at the earliest. Your help is greatly appreciated. Thanks in advance..

    What are you not clear on?
    What you need to do is get your developers to conform to a database naming standard, as stated above, so if you have an oracle database that is for eBusiness Suite you get all developers to create a DB connection in JDev called, ora_esb as an example.
    When the developer creates a DB adapter this will create a JNDI name of eis/DB/ora_ebs. When the BPEL project is deployed it looks for the JNDI name in the oc4j-ra.xml file to see its connection details. If they don't exist then they use the developers connection details. The issue with this is that they generally always point to the development DB. It is best practice for the developers to remove the mcf settings in the DB adapter WSDL. This way if the JNDI name has not been configured it will fail.
    So when you migrate from dev-test-prod what you have is the JNDI name eis/DB/ora_ebs. The dev points to the dev instance of ebs, test points to the test instance and so on. This means that you don't need to adjust any code in the BPEL projects.
    cheers
    James

  • Are there any connection settings for using rtsp:...

    In my effort to get access in 'YouTube" steaming videos, I tried to find the scope available  in Nokia 3110C handset. After going through the Menu icons, I identified one Menu Item in the path : MAIN MANU>MEDIA>MEDIA PLAYER>GO TO ADDRESS. It is...rtsp://. The help message states ...'Lets you manually enter Web Address...'. I entered : ' rtsp//m.youtube.com. The response was a Note which reads - Check Connection  Settings... Again I followed the above path :  MAIN MANU>MEDIA>MEDIA PLAYER>STREAM SETT. I click the Stream Settings. The nesponsing note : 'No Settings found. Contact your Service  Provider'. So, from the above discussion the net  learning I got is I must have the Stream Settings to get YouTube going in my Set. My querry is : Whare those settings and what is the source in getting those settings ? I understood the rtsp (Real Time Stream Protocol) is more versatile than HTTP and MMS in getting Streaming data (numerical, photograph/radio). Please suggest.

    I experienced same problem with my 3110c handset. At first the STREAMING SETT was shadowed dark with a restriction to get access there. Later I got contact with BSNL (my SP). After downloading the settings I discovered that the shadowy patch over Streaming Sett. has gone. It  now shows an entry ..."bsnlstream."
    So far an attempt  was made to activate the Youtube, a message reminds me that the software of 3110C is not supporting such application.

  • XI and R/3 System connection settings for IDOC to File scenerio.

    Hi SAP champs,
                               I am working on a IDOC to File XI scenerio. But I am confused while configuring connection settings at XI system and R/3 system. I am finding problem in transaction IDX2 to maintain the IDOC metadata. Please let me know the complete step by step system cofigurations in XI and R/3 systems for the scenerio. Thanks in advance..
    Regards
    Sanjeev.

    Hi Sanjeev,
    We upload Medata in IDX2 to just reduce runtime effort and hence to improve the performance. However it is not a mandetory step to be performed for R/3 TO XI scenario.
    You are confused just because here you dont find any F4 help to select the metadata and the PORT.
    Thanks
    Sunil Singh

  • You may need to configure the connection settings in the deployment descrip

    Hi All
    I am new to BPEL and going through Order Booking Tutorial (using 10.1.3.4 version of opmn ) .
    I have a problem in 'Designing the Database Adapter to Insert Data' Chapter.
    I have installed Oracle 10g Express Edition and BPEL Process Manager on my local system.
    In the Example it has been asked to create a daabase connection with Third Party JDBC Driver. Instead I have created a database connection with Oracle(JDBC) Driver.So i didnt have to register any third party driver.
    I cud access the Order/OrderItems table as well .
    I Deployed the same on the server.But while running the process I get following error--
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    nested exception is:
         ORABPEL-11622
    Could not create/access the TopLink Session.
    This session is used to connect to the datastore. [Caused by: Listener refused the connection with the following error:
    ORA-12519, TNS:no appropriate service handler found
    The Connection descriptor used by the client was:
    localhost:1521:XE
    See root exception for the specific exception. You may need to configure the connection settings in the deployment descriptor (i.e. $J2EE_HOME/application-deployments/default/DbAdapter/oc4j-ra.xml) and restart the server. Caused by Exception [TOPLINK-4002] (Oracle TopLink - 10g Release 3 (10.1.3.4.0) (Build 080602)): oracle.toplink.exceptions.DatabaseException
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    I have checked several post on this error but every post talks about third party database.I have used Oracle Database only so why/What shud I change anything in oc4j-ra.xml?? This is my doubt .
    Pls help me on this .Also Let me knowe in my case is there any need to create the datasource.?I am low at concept of database.
    Pls help
    Regards
    Naveen

    Hi
    I am trying to insert orader and order Items as given in the Order booking tutorial..
    Here are the files description
    .wsdl file looks like
    <service name="DBInsert">
    <port name="DBInsert_pt" binding="tns:DBInsert_binding">
    <jca:address location="eis/DB/MyConnection"
    UIConnectionName="MyConnection"
    ManagedConnectionFactory="oracle.tip.adapter.db.DBManagedConnectionFactory"
    mcf.DriverClassName="oracle.jdbc.OracleDriver"
    mcf.PlatformClassName="oracle.toplink.platform.database.oracle.OraclePlatform"
    mcf.ConnectionString="jdbc:oracle:thin:@localhost:1521:XE"
    mcf.UserName="system"
    mcf.Password="6672B62098892995C8B651EFDF798A59"
    />
    </port>
    </service>
    data source file looks like
    <connection-pool name="MyConnection">
    <!-- (DESCRIPTION=(ADDRESS_LIST=(LOAD_BALANCE=on)(ADDRESS=(PROTOCOL=tcp)(HOST=nakhanna)(PORT=1521)))(CONNECT_DATA=(SERVICE_NAME=XE))) below is in the form: [hostname]:[port]:[oracle sid]" -->
    <connection-factory factory-class="oracle.jdbc.OracleDriver" user="orabpel" password="->pwForOrabpel" url="jdbc:oracle:thin:@(DESCRIPTION=(ADDRESS_LIST=(LOAD_BALANCE=on)(ADDRESS=(PROTOCOL=tcp)(HOST=nakhanna)(PORT=1521)))(CONNECT_DATA=(SERVICE_NAME=XE)))"/>
    </connection-pool>
    <managed-data-source name="MyConnection" connection-pool-name="MyConnection" jndi-name="jdbc/MyConnectionDS"/>
    </data-sources>
    oc4j-ra.xml looks like
    <connector-factory location="eis/DB/MyConnection" connector-name="Database Adapter">
              <config-property name="xADataSourceName" value="jdbc/MyConnectionDS"/>
              <config-property name="dataSourceName" value=""/>
              <config-property name="platformClassName" value="oracle.toplink.platform.database.Oracle9Platform"/>
              <config-property name="usesNativeSequencing" value="true"/>
              <config-property name="sequencePreallocationSize" value="50"/>
              <config-property name="defaultNChar" value="false"/>
              <config-property name="usesBatchWriting" value="true"/>
              <connection-pooling use="none">
              </connection-pooling>
              <security-config use="none">
              </security-config>
         </connector-factory>
    ##################################################################3
    Still I get the same error .
    <bindingFault xmlns="http://schemas.oracle.com/bpel/extension"><part name="code"><code>null</code>
    </part><part name="summary"><summary>file:/C:/product/10.1.3.1/OracleAS_1/bpel/domains/default/tmp/.bpel_FulfillOrder_4.0_e77c64251e45eb4711a3a093f92e6a86.tmp/DBInsert.wsdl [ DBInsert_ptt::merge(OrdersCollection) ] - WSIF JCA Execute of operation 'merge' failed due to: java.util.MissingResourceException
    java.util.MissingResourceException
    ; nested exception is:
         ORABPEL-00001
    java.util.MissingResourceException
    java.util.MissingResourceException
    java.util.MissingResourceException
    </summary>
    </part><part name="detail"><detail>null</detail>
    </part></bindingFault>
    Pls let me know if something looks wrong in the above files
    Thanks
    naveen

  • Unable to apply connection settings. The detailed error message is: 'NoCount' is not a recognized option

    My corporate database wizards have created a login for my small subsidiary to use to read selected data from the HR database.  It's meant to be used by an SSIS package to bring over data on who's a current employee and who's not.  
    The package has started returning connection errors, and when I try to log into the HR database via SSMS using this login I get the following message:  
    "Unable to apply connection settings.  The detailed error message is" 'NoCount' is not a recognized option."  
    If I click on OK I can still log in, but it looks like this error is causing SSIS to produce an error.  I've seen articles on vaguely similar errors logging onto an Azure database, but this one's on SQL Server 2012.  
    Anybody got any ideas?  Is there something I can change at my end, or is it a change that has to be made in the remote DB?  

    I'm getting confused seeing this
    The package has started returning connection errors, and when I try to log into the HR database via SSMS using this login
    I get the following message: 
    Whats the purpose of SSIS package if you're trying to connect to DB using SSMS?
    Please Mark This As Answer if it helps to solve the issue Visakh ---------------------------- http://visakhm.blogspot.com/ https://www.facebook.com/VmBlogs

  • Help required with (soundcard) connection / settings, thanks in advan

    Help required with connection / settings between a Creative Sound Blaster Audigy Platinum EX (soundcard) and a Creative DTT3500 Digital (5. speakers).
    The problem
    No sound from any of the speakers. (Exception can plug in headphones at front)
    Background
    My computer has been recently upgraded at my local computer shop and all programs re-installed (including driver update from Creative's website). However after reconnecting speakers and restoring the original settings I?m getting no sound from any of the speakers. I?ve followed all the available advice/instructions I can find on this website and manuals to no avail.
    Set-up
    Physical
    (Digital DIN) Speakers/decoder amplifier (DTT3500) connected to the (digital out) soundcard (Audigy Platinum EX) using minijack to DIN cable. (As per instruction manual)
    Software
    Creative Audio Consul ? setting as per instructions, however have tried variations in vain. (Note: above tabs there is a select device box with SB Audigy [A0000] in it ? only option. Just wondering what [A0000] means?)
    Your advice please. A simple step by step guide would be appreciated, many thanks in advance, Jon

    "My computer has been recently upgraded at my local computer shop and all programs re-installed (including driver update from Creative's website). "
    Do you have the original installation disk?
    If so, try installing THOSE drivers, ESPECIALLY if it worked before. Be sure to uninstall what is there now, first.
    Its natural for most people to want the 'latest' drivers for their hardware. However:
    After experiencing some difficulties with some CL 'updates' for certain products, I now avoid them UNLESS I am having a PROBLEM with the existing drivers.

  • Can you retrieve a task list for a user without specifying that user's connection settings?

    Hi
    I would like to know if it is possible to obtain a list of workspace tasks for a user of my choice. In the following code, taken from the relevant quickstart, I am able to retrieve a list of tasks for "administrator" because it is the "administrator" settings specified in the connection properties when obtaining an instance of ServiceClientFactory. If I wanted to obtain a list of tasks for user "greg", for example, is there a way I can do this without having to specify the settings for "greg" in the connection properties? I tried to invoke the setUserId() method of the TaskFilter interface but no tasks are returned for user "greg" in that scenario. The aforesaid user has 3 tasks assigned to him. If I specify the user name and password for "greg" in connection settings, I am able to retrieve his list of tasks successfully. However, this is undesirable because I want to be able to retrieve a list of tasks for any user of my choice, by passing a parameter. Is that possible? Code follows:
    //Start of code
    import com.adobe.idp.dsc.clientsdk.ServiceClientFactory;
    import com.adobe.idp.dsc.clientsdk.ServiceClientFactoryProperties;
    import com.adobe.idp.taskmanager.dsc.client.TaskManagerClientFactory;
    import com.adobe.idp.taskmanager.dsc.client.TaskManagerQueryService;
    import com.adobe.idp.taskmanager.dsc.client.query.StatusFilter;
    import com.adobe.idp.taskmanager.dsc.client.query.TaskFilter;
    import com.adobe.idp.taskmanager.dsc.client.query.TaskRow;
    import java.util.Iterator;
    import java.util.List;
    import java.util.Properties;
    public class RetrieveTaskInfo {
        public static void main(String[] args) {
            try {
                //Set connection properties required to invoke LiveCycle                                                                                                                        
                Properties connectionProps = new Properties();
                connectionProps.setProperty(ServiceClientFactoryProperties.DSC_DEFAULT_EJB_ENDPOINT, "jnp://localhost:1099");
                connectionProps.setProperty(ServiceClientFactoryProperties.DSC_TRANSPORT_PROTOCOL,Service ClientFactoryProperties.DSC_EJB_PROTOCOL);          
                connectionProps.setProperty(ServiceClientFactoryProperties.DSC_SERVER_TYPE, "JBoss");
                connectionProps.setProperty(ServiceClientFactoryProperties.DSC_CREDENTIAL_USERNAME, "administrator");
                connectionProps.setProperty(ServiceClientFactoryProperties.DSC_CREDENTIAL_PASSWORD, "password");
                //Create a ServiceClientFactory object
                ServiceClientFactory myFactory = ServiceClientFactory.createInstance(connectionProps);
                //Create a TaskManagerQueryService object    
                TaskManagerQueryService queryManager = TaskManagerClientFactory.getQueryManager(myFactory);
                //Define search criteria by performing a search on 
                //Assigned tasks (tasks assigned to the user specified
                //in connection properties) 
                TaskFilter filter = queryManager.newTaskFilter();
                StatusFilter sf = filter.newStatusFilter(); 
                sf.addStatus(StatusFilter.assigned); 
                filter.setStatusFiltering(sf);
                //Perform the search
                List result = queryManager.taskList(filter); 
                //Create an Iterator object and iterate through
                //the List object
                Iterator iter = result.iterator();
                while (iter.hasNext()) {
                    TaskRow myTask = (TaskRow)iter.next();
                    //Get the task identifier value
                    long taskId = myTask.getTaskId();
                    //Get the status of the task
                    long taskStatus = myTask.getTaskStatus();
                    //Get the name of process on which this task is based
                    String processName = myTask.getProcessName();
                    //Get the task description
                    String taskDes = myTask.getDescription();
                    System.out.println("The task identifier is " + taskId + "\n" +
                            "The status of the task is " + taskStatus + "\n" +
                            "The name of the process on which the task is based is " + processName + "\n" +
                            "The task description is " + taskDes);
            } catch(Exception e) {
                e.printStackTrace();
    //End of code
    Thanks
    Darren

    Paul,
    Thanks very much, I never tried just asking for the parameter I was looking at the entire list coming back from a query with no filters. Using the DBMS_LDAP package you can in fact get their GUID.
    I understand your concern for the use of the field and for other reasons have moved to a different identifier to tie OID accounts to our internal application user accounts.
    Thanks very much, I'm still glad to know how to do get at the info.

Maybe you are looking for