Router does not answer

My router does not work with my computer but it works with my external driver. Also I have a PC conected to the router and it works...

My router does not work with my computer but it works with my external driver.
I don't understand the second part of that sentence.
As far as your computer is concerned,
1. Change the ethernet cable.
2. Open a browser on your Mac, and enter the router's ip - the manual will tell you what it is. Usually something like 192.168.1.1. You may have to wait for a response. If you do get a response. it will be a log-in window asking for a name and password. This info too should be in the manual.
3. Follow the instructions to set up your Mac to communicate with the router.
If this does not work, post back with a description of what happened.

Similar Messages

2811(NM-8AM) does not answers incoming call from PC

Dear friends,
We are planning to setup an out of band management connectivity, in our test setup we have a Cisco 2811 ISR (with IOS 12.4(9)T5 ) with NM-8AM (Analog modem module) installed.
Test Setup:
1. One Analog line (PSTN) connected to PC via built-in modem
2. Second Analog line (PSTN) connected to Cisco 2811 (NM-8AM) terminated on the analog modem module
3. Both the analog lines are working fine.
Test Scenario:
1. The router should accept the incoming call from PC. And from the PC we should be able to telnet into the router via dial up connectivity (Out of band)
Test procedure:
1. The Cisco 2811 router is configured as follows:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Dial-Up-CPE
boot-start-marker
boot-end-marker
logging buffered 16384 debugging
enable password cisco
ip cef
voice-card 0
no dspfarm
username cisco password 0 cisco
interface Loopback0
ip address 10.10.10.1 255.255.255.255
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Group-Async1
ip unnumbered Loopback0
encapsulation ppp
dialer in-band
dialer idle-timeout 600
dialer-group 1
async mode interactive
peer default ip address pool DIALIN
ppp authentication pap chap
group-range 1/0 1/7
ip local pool DIALIN 172.16.16.1 172.16.16.5
ip http server
no ip http secure-server
dialer-list 1 protocol ip permit
control-plane
line con 0
exec-timeout 0 0
line aux 0
exec-timeout 0 0
password cisco
modem InOut
transport input all
stopbits 1
speed 38400
flowcontrol hardware
line 1/0 1/7
modem InOut
transport input all
stopbits 1
flowcontrol hardware
line vty 0 4
password cisco
scheduler allocate 20000 1000
2. With the above configuration, the router is not able to answer the incoming call from the PC.
3. And from the PC we are able to dial to a PSTN number at the router side, PC gives a proper dial tone and once the number is dialed, the call is landed on the other side (router end) and it rings continuously. But, the router does not answer this incoming. The analog line at the router end is terminated on async interface 1/0.
As I am new to dialup connectivity with NM-8AM, Could some please suggest the proper configuration in our router configuration OR Are missing any commands?
Any links/references would be of great help.
Thank you
Pradeep

Hi,
I guess I'm having exactly the same setup. The integrated modem on the other end does pick up the call but soon disconnect after displaying "Waiting for carrier".
Any clue?
Thanks,
Eyad

2509 router does not accept wan ip with subnet

hi i hv 2509, 2501. while configuring wan ip on serial interface its ot allowing me to configure ip with other subnet mask , its allowing only ip with default subnet mask, for eg- if i giv 202.54.10.1 255.255.255.252 on s0 of 1st router then router does not allow me to configure , but if i give 202.54.10.1 255.255.255.0 then it configure smoothly , can any body tel me why?

I am not confident that ip classless will help this issue. ip classless has to do with how we interpret the content of the routing table and not to do with how interfaces are configured. It is more likely that the ip subnet-zero command might be the solution for the symptom described.
I would ask for some clarification from Gulshan. When you attempt to configure the router with 202.54.10.1 does it give error message saying invalid mask? If so it is a symptom of attempting to configure an address that falls into subnet zero (which your example does). If you configure the router with ip subnet-zero and then attempt to configure the interface it should work ok.
Restriction on the use of subnet zero was common many releases of IOS ago. But those restrictions are not common in more recent versions of code. It sounds like your router is running code which enforces this restriction by default.
HTH
Rick

My netgear router does not recognize my password and i cannot access it with my iphone

My Netgear DG834PN router does not recognize my user name or password when i try to access WI FI with my iphone.I cannot get wifi on my iphone from this or any router. The router is a wireless and hardwired unit.

Is your password by any chance in Hex? (all numbers or letters a through f) If so you may be able to translate the hex into ASCII or you could change to an ASCII password. I had to make that kind of change. Good luck.

Routing does not match selection ID 01

Hi all,
I have query while run the costing (CK11N) for Assembly Material. Error displays as "Material X: Routing does not match selection ID 01".
This Assembly Material has Routing with 2 Direct and 5 In-direct opeartions as well as defined the Labor for Direct Operations with respect to the CC assigned in WC.
Can anyone help me out why this error occurs?
Regards,
Sundhu

Dear Sundareswari,
Goto OKKN->select the Costing variant that you have used in CK11N and under control tab goto quantity structure control
>check the value or ID assigned for routing selection.
As per this your routing gets selected in CK11N or CK40N.
Check and revert
Regards
S Mangalraj

"Switchboard (reagiert nicht). "Switchboard does not answer" HEEEEEElllllllPPPPP !

Hallo,
Bin auf Power Mac.
Adobe Photoshop Version: 2014.2.2 20141204.r.310 2014/12/04:23:59:59 CL 994532 x64
Betriebssystem: Mac OS 10.9.5
Aktivitätsanzeiger zeigt immer wieder die Meldung "Switchboard (reagiert nicht) (Rot)
Habe das Dossier SwitchBoard bereits einige Malen aus die Preferences gelöst
und auch ein neuer User angemeldet.
Problem bleibt bestehen.
Konnten anfänglich Mini-Bridge in CS6 anklicken ... bliebe aber hängen.
Kann heute Mini-Bridge in CS6 überhaupt nicht aufrufen.
Und sonst ist Bridge CC sehr langsam im Vergleich zum früheren Bridge CS6
Hat irgend jemand eine Ahnung was los sein könnte ?
Viel Dank im Voraus.
JM
Hello,
Working on a Power mac.
Adobe Photoshop Version: 2014.2.2 20141204.r.310 2014/12/04:23:59:59 CL 994532 x64
Betriebssystem: Mac OS 10.9.5
The activity mesure of my engine always figures: Switchboard (does not answer) (in red).
I deleted "Switchboard" from the preferences (like the Support proposed me to do) and
tried a new user ... Does not matter: I always get the same failure mention.
At the beginning of the trouble, I could click on Mini-Bridge in CS& but it let me hang on.
Now I can not use mini-Bridge in CS6 at all. No answer at all !
And Bridge CC ist very slow compared to Bridge CS6
Anybody an idea how to fix this ?
Thank you in advance.
JM

Hello John T Smith,
I had contact with two people oft this so called "support".
The both told me the same ... and I did follow their instruction strictly,
helped by a very good Mac technician.
Nothing helped !
So I wrote them again ... and, you know what ?
They send me AGAIN, exactly the SAME useless ANSWER.
That's why I am here, asking for help.
And now, I suppose, they will erase my post ... ?
Sorry ... I am loosing patience ...
Best regards,
JM

When I try to import a movie from finder, iMovie does not answer.

when I try to import a movie from finder, iMovie does not answer. The system will freeze and stay this way up to when I force imovie to stop. I cannot solve the problem myself. Any help? Thanks

the movies I tried tio import are .mpg and .avi
Imovie started to show this after I tried to import the movie from the finder, but from the camera it is OK.
I was makin a project movie with imovie when this happened.
from the console:
10/09/13 10:45:00,880 com.apple.launchd.peruser.501: ([0x0-0x90090].com.apple.iMovieApp[1163]) Exited: Terminated: 15
10/09/13 10:45:07,147 spindump: Saved hang report for iMovie version 9.0.9 (1795) to /Library/Logs/DiagnosticReports/iMovie_2013-09-10-104507_iMac-de-Michel.hang
10/09/13 10:45:30,880 com.apple.usbmuxd: stopping.
10/09/13 10:45:30,923 com.apple.usbmuxd: usbmuxd-296.4 on Dec 21 2012 at 16:11:14, running 64 bit

After registration of 6 divices/apps I bought two readers. Now I cant not use them because of no free license. What can I do? Adobe does not answer my questions.

After registration of 6 divices/apps I bought two readers. Now I cant not use them because of no free license. What can I do? Adobe does not answer my questions.

Thanks too all the people who responded. . . . (noone)
Got it sorted though. Seems that Apple has issues with multiple apple id's.
Seems i had to somehow remember and use the original id i had when i first bought my 1st iPhone. . . .
Even after that it was extremely hard to get my apps back on my PC.
If anyone else has the same problem. . . .email Apple. Cya.

WRT610N V2 wired as 2ndary router to wired router, does not give IP address wirelessly

My WRT610N V2 is wired as 2ndary router to a wired router but it does not give IP address wirelessly to connected PCs.
It is getting DHCP IP address in the 192.168.1.xxx range from the 1st router, on its internet port, and issuing properly an IP addresses in the 10.10.1.xxx range thru its LAN port when wired to a laptop.
But if I connect to its 10.10.2.xxx wireless network with another laptop, the wifi adapter utility software shows the laptop is connected, but the laptop is not receiving an IP address. Please help in correcting this, as I need to use this router to give internet access wirelessly to guest laptops.
I know DDWRT does this kind of bridging with secondary DHCP when both routers are connected wirelessly, but it seems to me that if the 1st and 2nd router are wired together, DDWRT shuld not be needed for 2ndary HCP to take place.
And 2ndary DHCP is indeed working for those laptops wired to the 2ndary Cisco router: seems to me it should be able to do it also wirelessly.

In the upper right search bar type in 'two routers' to find your answer.

Wireless Router does not work

I am at a university that does not want you to use wireless routers, yet everyone around me still has theirs and when i open my Airport dropdown, i see numerous wireless networks that are run by students.
My router is the ZyXEL HS-100W (a cheap router, but it has always worked for me in the past).
When i turn the wireless on through the router's firmware, it is registered on my airport's list, and when i type in my password (WPA), I get the green light in network prefrences and it says something along the lines of "user assigned IP" I have full bars, and it says I am connected, yet whenever i try to open a webpage, it says that I am not connected to the internet.
I tried to turn the firewall off inside the router, and it did nothing, I tried to use no security to see if that would work, and it did not.
I do know that we have to register MAC addresses with the computer department here, so I am not sure if there is a way to do this within OSX or within the firmware.
I know that this is probably very vague, but I am looking for whatever support I can get.
Thanks
ben

it was a good suggestion, but i cannot find a place to manually set a MAC.
The closest i could find is under the WAN page, there is a tab called WAN MAC.
in that tab is "spoof this computer's MAC Address - IP Address" and then has a spot to input an ip address (the default is in the 192.168.. just generic ip).
i tried to input my computer's ethernet mac address, and it didnt work.
maybe there are futher suggestions based on this?
also, i am not sure if this matters, but when the router is plugged in, and I am wired to the router, i can get internet, but once i switch to wifi, i dont get internet. maybe that will help.
thanks
ben

HT1595 cannot connect ATV to actiontec router with wired ethernet. router does not see ATV. is there a way to test the ATV ethernet port on the back?

have an 3g ATV (5.0 4099) wired via coax cable to actiontec MI 424-wr router. Router cannot see ATV. Is there a way to test ethernet connector on back of ATV? ATV does work when setup for wireless but its much too slow for actual use when configured that way.

Steve,
I think the isssue is clearly that your router is not acting as a DNS Server. You will need to contact Verizon to see how to configure it so that it does supply the DNS addresses. If you can configure it in your Router try using 8.8.8.8 and 8.8.4.4 as the DNS Server addresses. These point it to Google's Public Domain DNS Servers. There are others (opendns.org). But for now these will hopefully get you up and running.

TS1398 Wifi in off and on mode: I have a problem connecting to my home wifi. Everytime i need to touch the wifi setting. I need to switch off and on again and again. Restarting my router does not help

Sick of this wifi issue in my iPad mini.

If you are having WiFi problems it is necessary to isolate whether the problem is with your network or your iPad. Note: Do NOT consider your network to be blameless if some other devices can connect to it.
First, test your iPad on some other networks: a friends, Starbucks, Barnes & Noble, etc.
If it works well there then the problem is probably with your network. Check for a firmware update for your router. If none exists which corrects the problem consider replacing the router.
If your iPad does not function well on other networks it possibly has a hardware problem. You could try Settings > General > Reset > Reset Network Settings to see if that corrects the problem. If not, contact Apple Support or visit an Apple store for evaluation. They can provide a replacement if your iPad is bad.
If you need more help please give the make, model, and version of your WiFi router and how you have it configured.
See also here: http://www.apple.com/support/ipad/wifi/

Port Forwarding in WRT54GL Router does not work

When i forward ports in the firware it does not work correctly. I tested it using http://www.yougetsignal.com/tools/open-ports/ and it still said that the port was closed.

Who is your ISP. When you do port forwarding make sure you have entered the IP address of the computer for which you need to enable port forwarding. Under "Security" Tab uncheck "Block Anonymous Internet Request" and click on Save Settings.After this try testing if that port is opened or not.What ports numbers you are trying to open on your router.

MY WIRELESS ROUTER DOES NOT LIKE WINDOWS 7

OK FIRST I'M NOT YELLING. CAPS ARE MUCH EASIER FOR ME TO SEE AS I HAVE MS. ANYWAY I AM A NOVICE USUER WHEN IT COMES TO ROUTERS BUT MY ROUTER Wireless-N Broadband Router (WRT300N) DOES NOT LIKE MY NETBOOK WHICH HAS WINDOWS 7 HOME PREMIUM. DOES ANYONE KNOW HOW I CAN EASILY FIX THIS.
THANKS IN ADVANCE,

Are you able to see the wireless network name on your computer ?
If yes, then what's the error message are you getting while connecting to the network ?

My WRT54G router does not function

Dear All,
I have a Wireless-G broadband router WRT54G, which is connected to a speedtouch ADSL modem.
When I connect the Modem directly to my pc, the internet connection is ok.
When I connect the Modem to the router, and then open the web tool, (192.168.1.1), I can see that the status of the router is connected, DHCP is enabled, and the username and password are correct for sure.
I connected the pc to the router and got an IP address 192.168.1.100 given by DHCP, the DNS is also configured automatically and is correct, but there is no internet connection, everything I request does not give any response, I had a look on the connection status to the router, I can notice that the router is not giving me any packets.
I tried to upgrade the firmware (but I already have the latest version since a month and everything was ok during this month), and tried to reset to factory settings and reconfigure the router, but was useless.
I even tried changing the ethernet wires. But nothing works.
Is it a hardware problem or did I miss something?
Thanks in advance.
Regards,
Yaman

Hi… reset the router back to factory default settings.
1) Logon to router’s setup page and go to status tab, check the WAN/Internet IP, if it gives you 192.168.1.x, go to setup tab and change LAN IP to 10.10.10.1, save the settings and power cycle the n/w, check whether it works or not.
2) Well in the status if IP address is 0.0.0.0, go to setup tab and change LAN IP to 10.10.10.1, also change Internet Connection Type to PPPoE and setup user name and password, save the settings also reduce MTU to 1458 and power cycle the n/w. let me know the results.

Router does not answer

Similar Messages

Maybe you are looking for