Router-dsl issues SOLVED

I'm running Arch-i686 on P4,2G ram,NVGeForce6200 ,turtlebeach sound card and sis900etho/lan(using mii module not sis900) pci card. The previous install was aborted because pacman wouldn't work even with pppoe. I had used Arch two yrs ago (after using SW since version8-10.2) but broke the system too many times). So after a break I re-installed and tried setting up network via beginners's guide and an old 'Simply Linux' Jetblackz(?) guide. Remembering that Debian had same problem with network setup, I used pppoe-setup and that got me going,this time, to full install. And I got a notice about adsl handling networking.
I must say the xorg setup has changed a lot and took 'mucho' time. Other than that the install has been fast and stable even with all the pacman updates. It seems any "burps" in system are eventually fixed with updates. And thank goodness VLC allows audio cd playing! Kscd and other programs that used to, in older Arch/Kde, won't play audio cds.
But it bugged me that I still had to use pppoe. SW12.2,Suse11.1,Ubu9.04,Mandriva-2009 and various live-cds, including Desktop-BSD, just connected me during install. Win2000pro still uses 'winpoet' for Verizon DSL connection. I refused to upgrade to XP or Vista.
So I installed wicd. That automatically connected me to the wired router after asking me for the root password.
Prior to this 'ifconfig' showed eth0,lo and adsl connection. Putting !adsl and adding wicd to the /etc/rc.conf Daemons list, without network or netfs, gets me a tray icon in Kde4.2 showing wired-connection like in my other linux installs. Now 'ifconfig' shows eth0 and lo. Would that the install cd included wicd or had a more current quick 'wired-connection' setup.

If you solve a problem, you can write it to the community. It will maybe help somebody

Similar Messages

Apple AirPrint, talktalk router DSL 3780, HP PHOTOSMART printer 3780

I have gone through the whole raft of solutions to AirPrint from my ipad3, I am up to date with ios 8.1.3, my printer software is also up to date. My router DSL 3780 was supplied by talktalk about 12 months ago, But I still cannot locate air printer on the iPad... Can anyone help. Pretty please.

Hi @Daveeh,
Welcome to the HP Support Forums! I see you are running into some problems locating your HP Photosmart 5520 on your iPad.
I would like you to take a look here: Printing Over a Wireless Network with Apple's AirPrint FAQs, once on the page please complete the steps listed under the 'What if a 'No AirPrint Printers Found' message displays on my Apple device?' section.
I hope this helps, please let me know the outcome.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

OTA Update 4.08.605.2 "Rebooting Now..." Issue - SOLVED!

After so many tries and frustration I finally came across the information below and it worked like a charm
http://forums.androidcentral.com/verizon-droid-incredible/134246-second-gb-update-patch-wont-reboot-issue-solved.html
Can't say this will work for everyone, but it worked for me.
Boot into recovery
Press and hold Power, Choose "Restart" option
When screen turns off, press and hold Volume Down and Power
When the white HBOOT screen appears, use the volume button to move down to “RECOVERY.”
Press the Power button to select “RECOVERY.”
When the triangle and exclamation appears, hold the Volume Up and Power button at the same time.
Using the volume button, scroll down to “Wipe cache partition” and select it.
Select "Reboot system now"
You can now wait for the update to show up again, or try one of the methods in the post: For those who want the second GB update/patch to get the update again. It should reboot this time. Beware, it will stay at the Droid Eye screen after reboot for a while (~5 mins), but eventually, it did get installed. Be sure to make a lot of space for it though...

The restart option that AmDroid is talking about is not on the regular phone menu. Please read his post carefully. What he is talking about is in an advanced recovery based menu option.
Also, I was on 2.2 and the clear cache set date and time forward trick did not work for me to get the udpate. The clear cache and set date and time forward trick seems to mostly work if you are already on 4.06 software version and want to get the 4.08 software version.
For those on 2.2, patience is warranted! However, if you really cant wait and want to go the 4.06 update manually, you can search Android Forums dot com for manually install gingerbread. And don't worry about the article talking about being rooted. You dont need to be rooted. The instructions will work for a stock phone too. As soon as you do the manual 4.06, the 4.08 update will show up immediately.
Hope this helps!

Hi all ...I would like to add a language that is not available in Photoshop cc2014 .. My computer writes it but backwards .. How can I have this issue solves?

hi all ...I would like to add a language that is not available in Photoshop cc2014 .. My computer writes it but backwards .. How can I have this issue solves?

What language are you talking about? You might need to enable Edit/Preferences/Type/Middle Eastern and South Asian for proper display.

Verizon is not responding to DSL issues

Verizon appears unwilling to admit that the widespread DSL issue reported by customers in the last few days is a result of the company, not the user. To continue to charge monthly fees for services not rendered is fraud.
I would recommend that if you have a minute, and a working internet connection, that you file a complaint with the Federal Trade Commission. Their online complaint form is found at https://econsumer.ftccomplaintassistant.gov/.
File enough complaints, and we may actually get a response from this ridiculous company.

RalfN makes a great suggestion. I have rarely had extended outages but have never had a problem getting a credit on my bill for days when my internet service was very slow or not working at all.
If a forum member gives an answer you like, please give them the Kudos they deserve. If a member gives you the answer to your question, mark the answer as Accepted Solution so others can see the solution to the problem. Thanks !!!
http://forums.verizon.com/t5/Verizon-net-Email/Fix-for-Missing-Inbox-sent-folders-etc-with-Internet-Explorer-11/m-p/647399

Compact 2013 Interrupt Issue Solved

As flagged as a comment to the post here, "My iST isn't called", there is a solution in the pipeline (as an update) for ARM interrupt issue. The issue is that interrupts that are close to timer ticks get lost. There is a complete discussion
of this on my blog at:
http://embedded101.com/Blogs/David-Jones/entryid/586/Windows-Embedded-Compact-2013-Interrupt-Issue-Solved
Cheers David Jones
Embedded MVP

As flagged as a comment to the post here, "My iST isn't called", there is a solution in the pipeline (as an update) for ARM interrupt issue. The issue is that interrupts that are close to timer ticks get lost. There is a complete discussion
of this on my blog at:
http://embedded101.com/Blogs/David-Jones/entryid/586/Windows-Embedded-Compact-2013-Interrupt-Issue-Solved
Cheers David Jones
Embedded MVP

DSL issue with HP Computer

I purchased a new HP Pavilion desk top 4 days ago. I can connect to the MSN home page but if I click a link nothing. I cannot log into verizon.com or any other websites either. I am connected to a Westel 327w, which is probably 5 years old or more, could this be the problem? This new computer is connected by Ethernet cable, wireless access on other computers is working fine. Any help would be greatly appreciated, I am becoming very frustrated, tried to use DSL CD from Verizon but it is also old and outdated and will not work. HELP! Thanks Debra

Update the drivers for your Wired/Wireless adapter. A lot of new computers tend to have outdated drivers installed as a part of the image. Some people have reported that this has solved this particular issue, and this would be the way I would approach this problem, as I originally suggested when this problem first surfaced. People have also had luck with updating the firmware on their modem/router, and others have had luck with bridging their modems to another router or replacing the modem/router all together.
The best way to find updated Drivers is to Google the component that needs updating (eg; Realtec Gigabit NIC, Atheros BGN Adapter), and downloading the driver directly from the device manufacturer's website. Getting the driver from the PC Manufacturer often will result in the same old driver, or one that is slightly newer.
========
The first to bring me 1Gbps Fiber for $30/m wins!

BEFW11s4 version four router configuration issues

Our wireless router quits sending out the wireless signal once a day. I called linksys and they had me get the new firmware, which solved the problem for about two weeks, but now the router is up to all the old tricks of not working. We have At&T (formerlly SBC) DSL internet. All the lights are lit up on the DSL box, and when I connect the router, the power, the wireless-b, the ethernet, and the internet lights all light up the way they should. Yet on the computers that hook up through the wireless connection it is limited or no connectivity. I keep trying to run the set up CD that came with the router, but every time it gets to the stage of configuring the router it stalls at 99% and then says it can not configure the router (despite that all the lights are on and working). I have tried numerous times to unplug it and holding the reset button and none of this is working.
I have also tried setting a static IP in network connections instead of having it find it automatically and this did not work either. I am really at a loss.
I searched the easy answers tips and can not find anything to help me. If anyone can help I would really appreciate it.

install the patch KB884020 from the following link
CLICK HERE
with regards to "limited or no connectivity"
(Mod note: Edited post so not to keep thread from stretching. Thanks!)
Message Edited by JOHNDOE_06 on 08-04-2006 05:31 PM

Apple TV Home Sharing Issue (SOLVED for me)

I had been having problems with Home Sharing while other functions (Netflix etc) worked fine. My setup is wireless using Time Capsule. My network was "open" (password not needed). I had tried everything from recycling my DSL modem and Time Capsule and turning Home Sharing off and on (on my computer and the Apple TV) without success.
My Time Capsule has the ability to connect at 5GHz or 2.4GHz. Additionally, my networks may or may not be password protected. I finally changed to a network that required a password and my Home Shareing issue ended. Since that network change everything works fine.

I was going crazy trying to play music from my Itunes library and watch slideshows of my photos as, once started, the application would quit within a minute of starting. I called Apple Support and tried everything they sughgested - restart, restore etc. Finally, I turned my router off and let it reset. When I turned it back on. everything worked. I could have saved a lot of aggravation had I been instructed to do so originally.

Can you help? Two dialer interfaces with IP SLA for default route failover - issues

I have an issue with a Cisco 2821, it has an ADSL2+ HWIC whose ATM interfaces is linked to dialer 1 and a Gi0/1 interface with a pppoe client which is linked to dialer 2. Both dialer interfaces are up with their respective IP addresses. If the ADSL on dialer 1 fails i want the IP SLA to kick and and replace the default route for dialer 1 with one for dialer 2.
This config works if you manually shut down the dialer 1 interface, it injects the default route for dialer 2 and then when you unshut the interface, the default route for dialer 1 comes back. The problem i have is if you take out the cable for the ATM interface and take it down, it does not take the route out the routing table and the default route for dialer2, which works if you just shut down dialer 1 does not appear.
whats the difference between shutting down dialer1 and it fails over the default route and taking the cable out then it does not?
Here is my config, i'm sure its something simple i'm doing wrong, can anyone help???
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
enable secret 5 $1$qOOJ$HV5AH6US/YZMuCGPYp3pP.
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 192.168.0.1
ip dhcp pool pool1
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
dns-server 188.92.232.50 188.92.232.100
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
no dspfarm
archive
log config
hidekeys
track 1 ip sla 1 reachability
interface GigabitEthernet0/0
description Gi0/30 Local LAN
ip address 192.168.0.1 255.255.255.0
ip verify unicast reverse-path
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
no ip mroute-cache
duplex auto
speed auto
snmp trap ip verify drop-rate
no mop enabled
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
interface ATM0/2/0
description ATM0_DSL
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
logging event atm pvc state
logging event subif-link-status
no atm ilmi-keepalive
dsl operating-mode auto
dsl enable-training-log
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer1
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
keepalive 1 3
no cdp enable
ppp lcp predictive
ppp authentication pap chap callin
ppp chap hostname ********@ccsleeds.net
ppp chap password 0 ********
ppp pap sent-username *******@ccsleeds.net password 0 ********
interface Dialer2
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
encapsulation ppp
dialer pool 2
keepalive 1 3
no cdp enable
ppp lcp predictive
ppp authentication pap chap callin
ppp chap hostname **********@adsllogin.co.uk
ppp chap password 0 *********
ppp pap sent-username *********@adsllogin.co.uk password 0 ***********
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1 track 1
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 0.0.0.0 0.0.0.0 Dialer2 10
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
ip sla 1
icmp-echo 8.8.8.8 source-interface di1
timeout 1000
threshold 100
frequency 3
ip sla schedule 1 life forever start-time now
access-list 1 permit 192.168.0.0 0.0.0.255
control-plane
gatekeeper
shutdown
line con 0
line aux 0
line vty 0 4
password test
login
scheduler allocate 20000 1000
end

Sure that EEM can shut/unshut interface...you have "event track" in EEM for monitoring track events...for example:
event manager applet test
event track 1 state down
action 1.0 command "enable"
action 1.1 command "conf t"
action 1.2 command "interfac dialer 1"
action 1.3 command "shut"
action 1.4 syslog "Dialer 1 down!!!"
action 1.5 end
This would be an example from head :)
You would need another EEM similar to this one for unshutting interface with "event track 1 state up" for bringing interface up again.
Again as I said you would need to test this before putting in production and you would maybe need to tweak this a little bit acording to your needs...
BR,
Dragan

Purchased extreme to replace modem/router DSL used telephone cord need help with set up

Prior to purchasing Airport Extreme had a standard modem/ wireless router from ATT for DSL. I have two macbooks both dropped connections while online with older modem.
Airport Extreme purchased to correct connection issues I need help with set up. The older modem just used telephone cord. I tried to use telephone with extreme it did not work.
How do I get extreme to work as the modem and router ?

How do I get extreme to work as the modem and router ?
you can't. the extreme is only a router. you need a separate modem (or disable the wireless part of your old router and use it as a modem - if that's possible).

Yet Another Slow DSL Issue - Speed No Better Than Dialup?

I consider myself fairly computer savvy (as I work with them as a profession), but must admit that Internet Connectivity is not my forte...
I currently subscribe to the Hi Speed DSL Enhanced - lately, the speed has degraded to not much better than dialup. I have had this service for several years - nothing has changed on my end hardware-wise, so this event is not assumed to be from my end.
I am running:
Westell 6100 Modem (Transcever Rev 7.2.3.0/Software Version 4.04.03.00)
NetGear RangeMax Duo Wireless N-Router #WNDR3300
(2) computers are hooked up:
(1) XP - hardwired directly to the Westell modem
(1) Win7 - hooked up via wireless
Both computers are running latest version of OS, IE and all software is up to date.
Both computers use Kaspersky Internet Security (internet speed the same whether it is ON or OFF)
Absolutely NO Maleware/Spyware or Viruses on either computer
I reboot the modem several times/day - with no result in increased speed
(2) phones installed in home - both with appropriate filters installed
My 1st resort was to call support - I can tell you that will be the LAST time I utilize that 'service' I have come to the end of my rope with waiting extended periods of time, only to be connected with a foreign country, with a poor connection, with an operator that barely speaks english, only to have them read thru a script telling me to do ridicuously stupid things like 'reboot the modem' (no kidding) or swap my hardwire CAT cable from my computer to modem end-for-end?
Next resort was this forum - infinitely more helpful!
Ran a Transceiver Stats Check as a baseline - Speed (Down-Up) was a crappy 96 Kbits/sec by 448 Kbits/sec
Then I tried a couple suggestions from this forum - my new Transceiver Stats:
Transceiver Statistics
Transceiver Revision:
7.2.3.0
Vendor ID Code:
4
Line Mode:
G.DMT Mode
Data Path:
Interleaved
Transceiver Information
Downstream Path
Upstream Path
DSL Speed (Kbits/Sec)
608
448
Margin (dB)
8.0
13.0
Line Attenuation (dB)
63.5
31.5
Transmit Power (dBm)
14.7
11.9
HUGE improvement eh?
One thing I did notice when attempting to check for newer version of modem firmware - when trying to update from web it gave me a 'Cannot Connect to Server Error'?
Speed is noticeably increased - but is it still where it should be?
If not, what other fixes should I attempt?
And finally, why is it that every time the weather gets even slightly inclement (sky clouds over, rain, thunderstorm, etc) our DSL goes off entirely?
Thanx for all your help in advance!

Can you fill us in a bit on what you did to improve the synch speed on the modem? Did you find some advice around here to connect the modem to your NID or did you investigate for damage to the home wiring? Your line should be running at a higher speed, which for what you seem to have is 1184kbps down, 448kbps up.
Do you also have voice service with Verizon? If so, how is that, especially during storms? Getting any noise on it? It could be possible if the line is not having issues due to corrosion, somewhere along the line shielding could be missing, and in comes a storm CRC'ing the line out of service.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Ralink RT3290 802.11bgn Wifi Card - Possible Issues [SOLVED]

Dear Lucky owners of such a card, At least from my experience I realized it is not that bad card, even if most probably many production pieces were faulty or not working properly, and many issues can be resolved. Let me list in order of time the issues I faced and solved about this wifi card: 0) First issue is not about RT3290 card itself but it is related to 802.11w encryption compatibility in between Windows8 and Cisco not allowing 802.11n speed rates so failing to G speeds only. - SOLUTIONS: a. As first test I would recommend trying another router from different brand to see if connecting at 802.11n speed rates b. If you prove point a issue, then try to fix the issue based on following post (in which you can see the reply from myself Emanuele on the 29th of Nov 2014): https://supportforums.cisco.com/document/113836/windows-8-clients-cant-associate-cisco-unified-wireless 1) Signal strenght issue: original wifi card RT3290 installed on my HP laptop was having really bad antenna, with signal fluctuating and sometimes bad even really close to any Router I tried. - SOLUTION: Replace the RT3290 card even with same new card. (In my case as laptop was under warranty, I proved the issue via screenshots and they replaced with new card solving my signal strenght issue). 2) Original issue (1) was actually resolved after HP replaced the wifi card with same model, but with the latest driver installed 5.0.45 seems like wifi rates change too frequently based on high sensitivity of the driver itself, so that suggested me issue was still there, so making me re-testing anything from scratch. - SOLUTION: Install 5.0.37 Driver - frequent rate changes issue (with driver 5.0.45) disappears and sensitivity of signal to rate changes seems to be a really good compromise to have good throughput. 3) To check out 2nd issue above I started again using a third party software inSSIDer free version to check signal while I was doing speedtest on web.
- RESOLUTION:
inSSIDer normally works on Windows7 without any issue but on Windows8 (at least tested with RT3290) I have just discovered somehow this software was slowing down wifi card performance drastically showing a speed up to 0.1Mbps rather than 40Mbps. Simply closing the application issue was not recurring, so uninstalled it and after solving all the other issues above this card works perfectly (at least so far ) Hope this post will be informative and will help other about-to-get-mad guys as me

Hye. After I read up your solutions, I am quite impressive and really want to try out those solutions. However, I am not very computer wise and I really appreciate if you make a video on solving this problem. Up to you if you want to upload it on the youtube (so that others with similar problem can view it and solve the problem too) or you want to direct email to me ( [email protected] ). I really hope you can help me because I am stuck with this problem since last year. Thank you!!!

851 Router Config Issue

Hi all,
Hopefully this will be a nice easy one for you all.
I have recently configured and installed an 851 router successfully :) I now only have one issue, the damn thing switches itself off after a period of inactivity!
If I want to use it again I have to issue a reset command then a boot command.
This takes me to the:
router>
prompt. I then have to issue a copy start run command. And then a no shut on each of my interfaces.
Obviously I would just like the router to stay up and running. But I cant work out how to do it. Im sure that this is just a simple config issue and I would dearly love for you all to solve it!
If any of you know the answer can you please provide clear an accurate commands as I will copy it parrott fashion into the router.
Thank you all in advance.
Stuart

Hello,
as spremkumar already pointed out the config register usually is set to 0x2102. You can reconfigure the register by:
Router#configute terminal
Router(config)#config-register 0x2102
Router(config)#end
Then perform a reload and check whether the config is present after the router finished booting.
Hope this helps! Please rate all posts.
Regards, Martin

Router-dsl issues SOLVED

Similar Messages

Maybe you are looking for