Router ea2700 and switch se2800
Good evening,
I have a router connected ea2700 on the Internet port to a switch se2800.
e switch is connected and everything is gigabit nas.
if I try to transfer a file from PC, gigabit ethernet, the transfer rate does not exceed 8 MB/s.
if I transfer a file from the NAS to the PC speed is 15 MB/s.
the support advised me to change MTU manufacturer parameters,to disable protection,and clone the mac address.
the situation has not changed.
if I configure the router in bridge mode, the speed is 22MB/s and 45MB/s.
it happened to someone?
thanks.
Francesco
good morning,
thanks for the reply.
the configuration that I've reported,does not allow the use of nat router function.
now after the switch off and on again, the situation seems to have improved.
is it possible?
thanks
Francesco
Similar Messages
-
Hi everyone,
I plan on taking my CCNP (route) exam within the next month but I just notice that the exam will only be valid until Jan of 2015. Now my question is that if I take the exam older exam will it still be valid to combine the newer "Trouble shoot 2.0" and "Switch 2.0"? I would like to take the current route test instead of the newer version becaue I've been studying it but I like to know if it will be uselss or not when combining the other to make myself an official CCNP certification holder.I have found on search:
Q. Can I mix the current exams with newer exams to achieve CCNP Routing and Switching?
A. Yes, it is possible to mix version 1 and version 2 exams, but if you completed version 1 exams for ROUTE or SWITCH, then you will need to prepare version 2 ROUTE & SWITCH as well in order to pass the TSHOOT v2 exam because the TSHOOT v2 exam assumes knowledge of ROUTE v2 and SWITCH v2 topics.
The answer is unclear, yes you can mix, but you will have to prepare for version 2. I hope it's wrong information. -
My LMS 3.2 won't detect Switch 29xx , router 39xx and 7200
Hi ,
my LMS 3.2 won't detect my new Switchs 29xx , router 39XX and my 7200 router !!!!
ThanksFirst thing you would want to do is upgrade to the latest device package for Common Services (MDF). That can be done under CS > Software Center > Device Update, check CiscoWorks Common Services and Check For Updates.
You can also use CLI commands (my preference) for this:
PSUCli.bat -p cmf -d -dst c:\psu_download -all (will download common services packages to c:\psu_download\cmf)
PSUCli.bat -p cmf -install -src c:\psu_download\cmf -all (will install the packages)
Use the supported device table below to confirm if your devices are or aren't supported:
www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/3.2/device_support/table/lms32sdt.html -
Power consumption for router and switch
I have a linksys EZSX88W switch which I checked power consumption of 70ma idle. It's supplied by the adapter which has an output of 1000ma. Not sure what the consumption when switch is being used. I also have an WRT54GS but haven't checked consumption yet, but it's powered by the same 1000ma adapter. In an effort to save energy-that -GREEN FEELING- I was thinking of using on power adapter to power bothe the router and switch. Has anyone tried this yet?? Also if I posted this in the wrong area I hope the moderator will move the post.
thanksSo you are thinking of Powering on both the Devices using a single Power Adapter? Well never tried to make both the devices use a single power adapter. As far as i think its not possible. But if you still wish, you can give a try and check if that works for you or not.
-
Hi all,
Any one help me to configure router and switch log on windows server. I dont have any idea please send me link or guide to configure syslog server on windows. For PPTP vpn users also.Hi,
Are you asking, "How do I set up my Windows server as a Syslog Server"... in order to receive messages from your routers and switches?
If so, I'd suggest a google search on syslog server - locate and download the software there, and it should have a configuration guide with it.
Was this the information you were looking for?
Curtis -
Router 2811 and C2960 Switch Trunking Problem
Hi all
I got an problem with a trunking problem between Router 2811 and C2960 switch
In router 2811 - I created f0/0.1 10.65.20.1 (VLAN 1) and f0/0.48 10.65.23.1 (VLAN 48)
In C2960 - Vlan 1 10.65.20.30 , VLAN 48 10.65.23.30
Finally I can only ping VLAN 1 IP but fail to ping VLAN 48 IP, can help me how to troubleshoot it?
Hugo
Router 2811 Configuration:
interface FastEthernet0/0.1
encapsulation dot1Q 1 native
ip address 10.65.20.1 255.255.255.0
interface FastEthernet0/0.48
encapsulation dot1Q 48
ip address 10.65.23.1 255.255.255.0
C2960 Configuration:
interface FastEthernet0/24
switchport mode trunk2811#sh vlans
Virtual LAN ID: 1 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: FastEthernet0/0.1
This is configured as native Vlan for the following interface(s) :
FastEthernet0/0
Protocols Configured: Address: Received: Transmitted:
IP 10.65.20.1 388873 262275
Other 0 1723
390760 packets, 71854310 bytes input
263998 packets, 53723195 bytes output
Virtual LAN ID: 48 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interface: FastEthernet0/0.48
Protocols Configured: Address: Received: Transmitted:
IP 10.65.23.1 0 0
Other 0 20
0 packets, 0 bytes input
20 packets, 1883 bytes output
2960_24#sh int trunk
Port Mode Encapsulation Status Native vlan
Fa0/24 on 802.1q trunking 1
Gi0/1 on 802.1q trunking 1
Port Vlans allowed on trunk
Fa0/24 1-4094
Gi0/1 1-4094
Port Vlans allowed and active in management domain
Fa0/24 1,48
Gi0/1 1,48
Port Vlans in spanning tree forwarding state and not pruned
Fa0/24 1,48
Gi0/1 1,48 -
No 'ip routing' command on switch and yet intervlan routing.
Hi,
In my companies 4500 switch I see there is intervlan routing configured for the 4 Vlans it has but I do not see any 'ip routing' command on it
to enable routing on the switch. Can a switch route even though the command isnt there?Ran the 'show run all' command and it was there. Thought '
sh run | i ip' would display it but didn't.
Thanks for the command.
We just turned enterprise. I keep forgetting that. -
Behind Router and Switch, Can't Enter URLs Without Dot-Com
Hello all,
I switched my networking situation this morning and now I've lost my favorite feature...the ability to enter URLs without a .com and have Safari auto-complete them. Here's my setup:
Wall->modem->D-Link Wireless-G Router->Netgear Gigabit Switch->iMac
Before, I just had my iMac connected directly to the modem, but now I have some new devices that I needed to network in. The Internet and everything else is working correctly, it's just that one thing that really bothers me. I've thumbed around through manuals and D-Link's router settings and I can't seem to find the giant on/off switch switched to off. Any ideas? Help?
Thanks!Mateo wrote:
Before, I just had my iMac connected directly to the modem, but now I have some new devices that I needed to network in. The Internet and everything else is working correctly, it's just that one thing that really bothers me. I've thumbed around through manuals and D-Link's router settings and I can't seem to find the giant on/off switch switched to off. Any ideas? Help?
Based on your description of the change, my guess is that your iMac used to deal with Time Warner DNS directly and now it may be using the DNS routing settings in the D-Link. As the former owner of a D-Link I would guess you might go look in the WAN settings for the DNS field on the D-Link (in the browser-based configuration utility) and make sure the IP address there matches whatever you had entered in the DNS field in the Network settings on your Mac. -
Help with connecting MacBook Pro with Cisco Routing and Switches?
I'm running a CiscoASA 5510 router with several Cisco WS-C2960-48TT-L switches on a local network to connect with MacBook Pro. I need to be able to restrict access to specific users via their computer MAC address. ie: Joe Blow is limited to connecting through Switch 1 on port 10 and anywhere else he tries to plug in will simply not work.
You need to look at the documentation that came with your router and switches. Or ask your network admin to set it up. Your question has nothing to do with your Macbook Pro configuration. MAC filtering is done in the router not in the computers/devices connecting to the router.
-
Hi all
What is the difference in setting passwords to access the console, Telnet (line vty 0 4) and other passwords in routers and switches. Are all the commands and where you set the passwords at the cmd prompts the same etc
Regards
Glennconsole password is used to authenticate user when user will try to access device through console port.
Telnet password is used to authenticate user when user will telnet to the device from remotely.
Hope this URL will give you more information.
http://www.cisco.com/en/US/products/sw/iosswrel/ps1818/products_configuration_example09186a0080204528.shtml
http://www.cisco.com/en/US/products/sw/iosswrel/ps1835/products_configuration_guide_chapter09186a00800ca7d1.html
rate if it helps ... -
What is diff b/w pick and switch activity in bpel?
what is the difference between pick activity and switch activity in BPEL? example Please
1)The switch activity is an IfElse with two different flows, based on a conditional expression, derived out of existing message(s) in your process.
Eg. i) Whether the salary is greater than 10,000 or not.
ii) Whether the age is greater than 60 or not.
iii) whether the department is finance or not.
2)The pick activity is an IfElse with two different flows, based on two different messages/signals, that you can expect to receive(when you are waiting for a message) from outside of your process.
Eg. i) whether you received a reply message or a timeout signal.
ii) whether you received a AddNewEmployee message or UpdateEmployee message.
The (decision for which route to be taken for) pick activity is based on the MessageType, while the switch is based on the contents in a message. The pick activity implies that you are waiting for a message, this can occur, at the start of your process or in the mid of your process. However, switch activity doesnot wait for any message, hence can only occur in the mid of the process and can not be the start of a process.
Mark the posting appropriately as "helpful" or "correct answer", if your issue is solved. -
ios 6, my wifi doesnt work
even after switching wifi on and off
as well as removing saved wifi spots
and tried switching from manual to auto
it works intermittently after these changes are made, but still shuts off.
i have ios 6 on both the iPhone 4 & the Iphone 5.
my router at home is D-Link router
please help!You have the same problem in two mobiles? Uou....
I have had used D Link router before, and I faced problems to connect my computer.
Now I bought Netgear, and it shows strongly better than the f.... D Link...
Try:
Settings>>WiFi, and then turn off Ask for Conection;
Or:
Settings>>Privacity, be sure the Location Service is turn on;
Or:
In Settings>>General>>Reset, select "Reset all Adjusts". (Sorry, but it will change some personal adjustments, but will not delete anything at all) -
Is it possible to sort or filter the switch routes under the switching tab?
In Teststand 3.1, is it possible to filter the switch routes under the switching tab in Action Properties? Since I have a large amount of routes that have been created in Switch Executive, how can I filter out some of the routes from the "Routes to Connect" section?
The TestStand Switching does not provide any inherent filtering capabilities. You do have a couple of options, however.
(1) NI-Switch provides the ability to set up route connections in
different groups. The Switch Page in TestStand allows you to
select Routing groups as well as specific Routes. It may be
easier for you to organize your Connections as groups and choose
between different groups.
(2) The Property page also allows you to build route connection
string and use that string for your Switching actions. It
may be easier for you to build a Route string and easily change that
string rather than selecting your routes everytime from within the
TestStand window.
Good Luck!
Tyler T.
Applications Engineer
National Instruments -
Ask the Expert: Packet Capture Capabilities of Cisco Routers and Switches
With Rahul Rammanohar
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions about packet capture capabilities of Cisco routers and switches.
In May 2013, we created a video that included packet capture capabilities across multiple Cisco routers and switches. For each product, we began with a discussion about the theory of the capabilities, followed by an explanation of the commands, and we concluded with a demo on real devices. In this Ask the Expert event, you’re encouraged to ask questions about the packet capture capabilities of these Cisco devices:
• 7600/6500: mini protocol analyzer (MPA), ELAM, and Netdr
• ASR9k: network processor capture
• 7200/ISRs: embedded packet capture
• Cisco Nexus 7K, 5K, and 3K: Ethanalyzer
• Cisco Nexus 7K: ELAM
• CRS: show captured packets
• ASR1K: embedded packet capture
More Information
Blog URL: Packet Capture Capabilities of Cisco Routers and Switches
Watch the Video: https://supportforums.cisco.com/videos/6226
Hitesh Kumar is a customer support engineer in the High-Touch Technical Services team at Cisco specializing in routing protocols. He has been supporting major service providers and enterprise customers in routing, Multiprotocol Label Switching (MPLS), multicast, and Layer 2 VPN (L2VPN) issues on routing platforms for more than three years. He has more than six years of experience in the IT industry and holds a CCIE certification (number 38757) in service.
Rahul Rammanohar is a technical leader with the High-Touch Technical Support Team in India. He handles escalations in the area of routing protocols and large-scale architectures for devices running Cisco IOS, IOS-XR, and IOS-XE Software. He has been supporting major service providers and large enterprise customers for routing, MPLS, multicast, and L2VPN issues on all routing platforms. He has more than 13 years of experience and holds a CCIE certification (number 13015) in routing/switching and service provider.
Remember to use the rating system to let Hitesh and Rahul know if you have received an adequate response.
Because of the volume expected during this event, Hitesh and Rahul might not be able to answer each question. Remember that you can continue the conversation in the Service Provider, sub-community forum shortly after the event. This event lasts through November 1, 2013. Visit this forum often to view responses to your questions and the questions of other Cisco Support Community members.Hello Erick
Thanks for the topology. The trigger will be different for labelled packet as you would need to mention the values of labels too in the trigger.
Below are two examples of one or two labels being used, it depends on where you are capturing the packet in mplsvpn scenario which will decide teh number of labels being imposed on the packet.
Trigger for one label. (if the router on which you are capturing the packet PHP is being performed)
VPN label - 5678
Source Address - 111.111.111.111
Destination Address - 123.123.123.123
show platform capture elam trigger dbus others if data = 0 0 0 0x88470162 0xE0000000 0 0 0x00006F6F 0x6F6F 7B7B 0x7B7B0000 [ 0 0 0 0xffffffff 0xf0000000 0 0 0x0000ffff 0xffffffff 0xffff0000 ]
Trigger for two labels. (for other core routers)
IGP label - 1234
VPN label - 5678
Source Address - 111.111.111.111
Destination Address - 123.123.123.123
show platform capture elam trigger dbus others if data = 0 0 0 0x8847004D 0x20000162 0xE0000000 0 0 0x00006F6F 0x6F6F7B7B 0x7B7B0000 [ 0 0 0 0xffffffff 0xf000ffff 0xf0000000 0 0 0x0000ffff 0xffffffff 0xffff0000 ]
You can check the labels being used (by using show ip cef <> details) and covert their values to hex and change the trigger accordingly.
I have changed the colors for better understanding. If you notice carefully in the trigger the values for ip address, labels have just been converted to their respective hex values which could be replaced.
Please let me know if this helps.
Thanks & Regards
Hitesh & Rahul -
Wireless AP native vlan and switch trunk
Hi,
I am unable to ping my ap, i think it is due to the multiple vlan issues, can provide some advise, my config for the ap and switch is as below
AP Config
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname hostname
logging rate-limit console 9
enable secret 5 $1$ZxN/$eYOf/ngj7vVixlj.wjG2G0
no aaa new-model
ip cef
dot11 syslog
dot11 ssid Personal
vlan 2
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 070E26451F5A17113741595D
crypto pki token default removal timeout 0
username Cisco password 7 1531021F0725
bridge irb
interface Dot11Radio0
no ip address
encryption vlan 2 mode ciphers aes-ccm tkip
ssid Personal
antenna gain 0
stbc
beamform ofdm
station-role root
no dot11 extension aironet
interface Dot11Radio0.2
encapsulation dot1Q 2
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio0.100
encapsulation dot1Q 100 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1
no ip address
encryption vlan 2 mode ciphers aes-ccm tkip
ssid Personal
antenna gain 0
no dfs band block
stbc
beamform ofdm
channel dfs
station-role root
interface Dot11Radio1.2
encapsulation dot1Q 2
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
interface Dot11Radio1.100
encapsulation dot1Q 100 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
duplex auto
speed auto
interface GigabitEthernet0.2
encapsulation dot1Q 2
bridge-group 2
bridge-group 2 spanning-disabled
no bridge-group 2 source-learning
interface GigabitEthernet0.100
encapsulation dot1Q 100 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface BVI1
ip address 192.168.1.100 255.255.255.0
ip default-gateway 192.168.1.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
password 7 01181101521F
login
transport input all
end
Switch Port config
interface FastEthernet1/0/10
switchport trunk native vlan 100
switchport mode trunkI will re-check the routing again but could it be some bridging issues ?
interface GigabitEthernet0
no ip address
duplex auto
speed auto
**** unable to put up this command on the giga port
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
I try to put this command on the gigaethernet port but it does not allow me, could this be the bridging issue ?
Maybe you are looking for
-
I have a desktop at work, and a desktop and laptop at home and just recently the "restore previous session" button that comes up when I use the desktop icon to start a Firefox Web browser session does not work. It is there and I click it but nothing
-
Creating a file in a removable disk in runtime
Hi, I want ti create a binary file in a removable flash card in run time. I am using win xp. this removable drive in in IDE channel as a master. there is no user interaction with the application.therefore how do i make sure the i am creating the file
-
I've been a long time with my I pod close...now I can't use or charge it!
Many months ago, I've lost my apple shuffle charger. Recently, my brother command me a new one from China. I didn't use I tunes for a long time and I uninstalled it. Now that I can recharge my I pod shuffle, I plugged it to my computer but the status
-
Hi, I'm don't work with video much but have to convert things from time to time into DVD. I was given a 19:9 ratio to work w/ this time but I only see 4:3 and 16:9 as options on DVDSP. What pixel dimensions(width, height) should the video be created
-
Having Problems / Waits while Rollback
Hi guys/Gurus, Hope you all doing well. I am having problem. The database is 9ir2.0.0.8. While doing an heavy transaction(Inserting in around 15 tables, 2000 records each.) The transaction encountered an error at the end before the commit statement.