Router Error Codes

Hello, I am trying to find one of my router error codes, however I can't seem to locate the manual below.
Can someone tell me how to find it?
Error code from the ICM CallRouter process. For information about a specific Router ErrorCode, refer to the Error Messages section of the *** ICM Master Help ***.
Thanks!

Barry,
This link should provide directions for looking up other codes...
http://www.cisco.com/en/US/products/sw/custcosw/ps1001/products_qanda_item09186a008024d1ef.shtml
Remember to rate helpful posts...

Similar Messages

Router Error Code 448

Hi Gents,
In RCD table we are getting lots of calls with RouterErrorCode 448. Any idea what could be the reason and how could we solve it. Its Request Type is Post Route and Originator type is VRU.
Software Versions:
CVP 8.5 with ES 6
ICM 8.5.4 with no ES or any other patch
CUCM 8.5

Hi,
I'd assume it's a sign of abandoned calls in IVR or queue - abandoned by the caller.
http://docwiki.cisco.com/wiki/RouterErrorCode%3D448_-_Dialog_%28%251%29_aborted_and_was_deleted.
G.

Unable to setup Router EA3500 due to Error Code 0x82BF010F

Hello Everyone!! I’m facing some issues during setup of my Linksys EA3500 Router. Firstly, I tried to configure the router using the Linksys Smart WiFi Router Setup CD.However exactly like the issue in the post http://community.linksys.com/t5/Wireless-Routers/EA3500-not-detected-during-setup/m-p/932205/highlight/true#M298971 I get stuck at 24-25% through the setup with the following error:Error code: 0x82BF010FError description: No Linksys Router wireless networks were found.Model name: EA3500Model description: unknownSerial number: unknownFirmware version: unknownOperating system: Windows 8 (64-bit)Software version: 2.0.12304.0Connection type (WAN): unknownIP address (LAN): 10.117.114.221IP address (WAN): unknown So, I figured that there is some issue here, where my Laptop fails to find the Router.Hence, I tried to setup the router manually through the following steps [using my hardwire Ethernet connections]:Resetting your Linksys router to factory default settings http://www.linksys.com/us/support-article?articleNum=136927 I was able to successfully factory reset the router.How to access the router’s web-based setup page http://www.linksys.com/us/support-article?articleNum=135561 Here in the link above, I required to use http://myrouter.local in Steps#2 & #3; since EA3500 is a SmartWiFi Router. However, I was not able to open the router’s web-based setup page as indicated in the link. Instead I was redirected to the Step#4 in the link below in #3.Setting up your Linksys router for DSL connection using Linksys Smart Wi-Fi http://www.linksys.com/us/support-article?articleNum=138278 As mentioned above in #2, I was directed towards Step#4 in the link here. I followed Steps# 4 through 11 as described. But, I fail to receive the Internet Restored prompt as in Step# 12. I’ve tried to powercycle the router and reboot my laptop; but in vain.Having spent considerable time redoing & re-performing the above, I’m at the end of the limited networking knowledge I have.I have referred to the community links on similar issue & tried to find out a solution:http://community.linksys.com/t5/Wireless-Routers/EA3500-Set-Up-Help/m-p/648700/highlight/true#M257491 Taking a clue from this post, I ensured that there is no conflict with other WiFi sources.http://community.linksys.com/t5/Wireless-Routers/EA3500-not-detected-during-setup/m-p/932205/highlight/true#M298971I hope to find a solution to this soon.I'm using a TD-W8969 Wireless N USB ADSL2+ Modem Router with a BSNL ADSL Connection [Type PPPoE LLC/SNAP] in IndiaThank You!!

If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Also check the routers DHCP IP address maybe conflicting with the ISP modems IP address of 192.168.1.1. Check to see if this is the same on the ISP modem, and if modem can't be bridged, change the Linksys router to 192.168.0.1 or .0.254.

Help !! Error code 82bd0305 router E1000

Hey !
I am treating to install a router e 1000
when I run the CD setup a get an error code 82bd0305
can anyone help me with this ??
Thanks

Welcome to the Cisco Home Community.
You can refer to this document on how to wire your router to your computer and access the setup page.
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

Error code 0XB80ACAA8 on my printer, when trying to connect to my router

Dear Support, I bought the printer 2 weeks ago. It worked perfectly, but since today I get the error code 0XB80ACAA8 when I try to connect to the Router. Can you tell me where the code stands for and what to do in order to resolve this?

Hello, Please try the below steps. remove the cartridges.Unplug the power cord from back of the pritner.power Off the wireless router.Wait for 60 seconds.plug in the power cord to the printer only.install cartridges when prompted.If issue still exits, its time to replace the printer.Now power on the wireless router.If issue still exists, then check if there is a firmware update for the router. Also change the router settings Channel = 11, mode= B/g. Frequency = 2.4 GHzIf issue still persists, then its time to replace the printer. Please call HP Tech Support for further assistance.
If you are in US , the toll free # is 1-800-474-6836 .
If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.

DPS APP Builder Error Code 1

Hello,
I'm getting an Error Code 1 message when trying to download the test APP from the DPS APP Builder. I've tried re-building the document (a process that takes almost 8 hours in my case as our APP features 110 articles including almost 1000 images), updating it, generating new certificates and any other workaround mentioned in a previous discussion about this same subject. Nothing worked for me.
The only workaround I haven't tried is deleting the folio from ~/Library/Preferences/StageManager.BD092818F67280F4B42B04877600987F01 11B594.1/Local Store/dmp.
Apparently, there's nothing called "StageManager" in my MacBook Pro. Not in this route neither in any other route.
Any idea about how to solve this? (if possible without re-building once again the whole document) We can't wait until the error code 1 bug is fixed in future Adobe updates as we need to submit the APP to Apple next week.
Thanks for your time.

Anyone can help??
Update my latest experimental results.
I found that issue was folio package related.
Because when I use another folio package to the same app item in App Builder, this error message does not appear.
But the original package in exchange, this error information occurs.
Are there helpful to solve this problem?

The operation can't be completed because an unexpected error occurred (error code -50)

I have a Seagate Central 3tb NAS (latest firmware) attached to my wireless router (Netgear wndr3400v3). I have a late 2011 macbook pro with Yosemite on it. When I go through finder to use my NAS I keep getting "The operation can’t be completed because an unexpected error occurred (error code -50)" . I only get it when I am trying to copy a big folder with other folders and files with in. I can copy a single file or create folders. If i try to copy a folder with 100 pics in it then I get the error. I can create the folder on the NAS and select all 100 files. When I drag them to the NAS, then they copy with no problems. Every so often my time machine has an error and says that it has to create a new backup. I read some where to make sure that "put hard disk to sleep when possible" should be selected in the energy saver in preferences. Still no luck. A can also drag any file from the NAS back to my laptop or view them from the NAS with no problems.
Thanks for any help in advance.
Billy

Hi there,
Well I have exactly the same problem! Recently I reset my WD My book White light (2 x 1TB RAID disk), due to the fact that the disk ran full because of TimeMachine.
I reset the disk, and now I can only write some files to it, but most give this error code.
I wrote to WD, but they could not give an answer.
Q: did you update the firmware? Maybe that is causing the problem, in that it is maybe not consistant in the filesystem?

DirectAccess Client not connecting without error code on Windows Server 2012 R2 and Windows 8.1

Hello,
we are currently migrating from Windows Server 2012 to 2012 R2 and are not able to get the new Direct Access Service up and running. Our goal is to establish DirectAccess connection for a handful of clients using the IPHTTPS-adapter on the default port 443.
Errors:
There is actually no error showing up. It seems the infrastructure tunnel cannot be created but none of the IPv6-transition adapters is connecting (teredo and 6-to-4 are down) and the IPHTTPs adapter gives no informations about a problem:
>Get-DAConnectionStatus
Status : Error
Substatus : CouldNotContactDirectAccessServer
>Get-NetIPHttpsState
LastErrorCode : 0x0
InterfaceStatus : Failed to connect to the IPHTTPS server; waiting to reconnect
Setup:
Our setup is a virtualized Windows Server 2012 R2 Standard running on Hyper-V. It is located behind a NAT having the Port 443 mapped to the server. The only role installed after the basic install is RRAS including DirectAccess and VPN. The assistants completed
successfully (running the configuration for DirectAccess and VPN). Operation Status says everything is green und working (for multiple days in the meanwhile). A previous direct access installation (on a different machine running Windows Server 2012) has
been removed before installing the new server. The new installation is using a different router, so this might also be the cause of a problem.
The client is a Windows 8.1 notebook located outside the company network accessing the internet through another NAT-device. The client has been able to connect to the previous DirectAccess setup but has never been able to establish a connection after the
setup of the new Direct Access server. The device has no outbound constraints concerning the NAT-device and is only running the integrated Windows Firewall.
Diagnosis:
So far I've done some basic DNS and connectivity checks. The DNS-name can be resolved correctly and the router even responds to pings. The port forward is working and HTTPs connections are generally possible (temporarily routed the port to
access the NLS-Website located on the server, which worked fine).
Network monitor shows that both computers are communicating, traffic on the expected Port 443 is incoming on the server and responses from the server reach the client.
Opening the IPHTTPs-url and in an endless page load. Sometime the browser page closes but I've never seen any result. Using telnet on the port shows that the server is accepting connections. I've even build a small test application that does a GET-Request
on the URL returning HTTP-200 and no content.
I'm currently running out of ideas what to do and since no error occurs this is kind of a bit frustrating. Any help appreciated.
Regards
Matthias

Hi,
In addition, have you disabled the DA client components on the DA client? If no, please also check
the settings on the Name Resolution Policy Table.
More information:
DirectAccess
Client Location Awareness – NRPT Name Resolution
In addition, error 0x4C9 means the remote computer refused the network connection. It may be due to the invalid
registry or corrupt drivers. For more detailed information, please refer to the link below:
Error 1225 - Error Code 0x4C9
Note:
Microsoft is providing this information as a convenience to you. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Best regards,
Susie

Error code: 0x80070035 The network path was not found

"Error code: 0x80070035 The network path was not found" while trying to access another PC running Windows 7 Ultimate I searched and read dozens of similiar posts to try to resolve this issue with no success.
The situation is, I have a router in home with 4 PC's connected. My central PC is running Windows 7 Ultimate. The others are Windows 7 Ultimate again, and 2 running XP Pro. No special Firewalls, just have Windows Firewall enabled on all PC's, and am running KasperskyInternetSecurity2010 on all. (Have disabled these on all PC's and tried to view/connect and it didnt make a difference, same error)
Fact one: not attempting a Homegroup connection at all, just simply wishing to connect in a basic network environment where I can drag and drop files between all PC's in my Home Network or in my house , however its considered. But on the Windows 7 I am unable to view either of the XP's only the other Win7, and when I try to access that one is when I get the "Error code: 0x80070035 The network path was not found".
Furthermore, while troubleshooting the problem I opened a Command Prompt in all computers, then an "ipconfig" to view each ip address. Then began to ping each machine to determin connectivity. Which resulted in partial success. My main Win7 machine (which i am on now) was able to ping successfully to all machines. But all other machines were unable to ping to me (main Win7). with a 100% loss.
So at least I determined this is most likely a helpful fact in resolving this. Going into "services.msc" I made sure that all the obvious services are started and running:
DCHP Client, Homegroup Listener, Homegroup Provider, Link-Layer Topology Discovery Mapper, NetTcp Port SHaring Service, Network Connections, Network List Service, Network Location Awareness, TCP/IP NetBIOS Helper
All strarted and running in Automactic mode.
Not sure what other information I can give at this point, to help assist in fixing this problem. Please dont hesitate to ask for me for more info if needed. Ready and willing to try anything to get this working, except for reinstalling the OS. All my programs work great and do not wish to go through the drama ao reinstalling all my programs and activating them and redoing all my Adobe settings and CAD settings.
Someone please help !

Hi,
In addition, I would like to suggest the following:
Enable NetBIOS over TCP/IP:
1.    Go to “Control Panel\Network and Internet\Network Connections”.
2.    Right-Click on the connection and choose Properties.
3.    Click “Internet Protocol (TCP/IP) Version 4” in the list.
4.    Click Properties, and then click Advanced.
5.    On the Advanced TCP/IP settings windows, go to “WINS” tab.
6.    Under NetBIOS setting, click “Enable NetBIOS over TCP/IP”, and then click OK.
Thanks.
Nicholas Li - MSFT

IPhone will not update (error code 1) will not restore even in DFU mode (error code 1)

I bought the iPhone 4S from a friend, and I came to wiping it manually from the handset, no problems found however during the initial steps the iPhone was unable to validate on the apple servers (with the carrier stuck on searching). So, I plugged the phone into my trusty laptop installed Itunes fresh and proceeded to restore. The process gets to the later part of the validation and throws up an Error Code 1.
I'm aware (from searches across the internet) that error code 1 is typically found in phones with tampered hardware/software e.g. Jailbreak, unlock etc. My friend is not tech savvy and doesnt have a clue about these things so I'm sure the phone is 'as is'.
So i proceeded to troubleshoot the issue:
I edited my hosts file to point to the apple validation server (and checked it allowed connections to gs.apple.com within my browser - successful).
Now as the handset is stuck in recovery mode (with the usb and apple logo) I tried to restore via regular Recovery mode - no sucess (error 1)
Entered the phone into DFU mode (which, in essence ALL of google preaches is the way to restore regardless of issue) same error occurred.
So i looked into 3rd party applications that could force it to restore or perhaps allow a functional end product.
Redsnow (latest edition only provides restore for up to iOS 6.1.somethingorother) that produced a dead end.
Pangu restore facility (latest edition for iOS 7/some 8 models) hanged at the same place as the apple loader.
I've tried flushing my DNS cache, and verified the Date/time on my computer and router is correct.
I refuse to accept the phone is nonfunctional but am rapidly running out of ideas as how to
a) restore it to the iOS it initially had
b) update it forcefully and have iOS 8
c) install a custom rom in the hope some fuctionality exists enough to restore it again.
Please inform me of any suggestions you might have,
regards Jack.
PS. Further information; This has been attempted on 2 seperate windows workstations both running windows 8.1 up to date.
The USB cable is an unofficial one but has caused no issues in the past on another iphone that ive restored.

Do you have the latest version of iTunes? Did you check for anti-virus software? One of the sections talks about interference from anti-virus software and firewalls. Also, you should not have to make any changes to your Host file unless your computer has been used to jailbreak a phone. I worry because you were using a number of software applications that are designed for jailbreaking devices. Excerpt from this support document. Get help with iOS update and restore errors - Apple Support
Check for hardware issues
Related errors: 1, 3, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
These errors mean that your device or computer might have a hardware issue that stops the update or restore from completing.
Check that your security software and settings aren't blocking your device from communicating with the Apple update server.
Then try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Make sure that your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support.

Error sending emails to Internet: Failed to connect. Winsock error code: 10051

Our exchange 2013 CU2 (CAS+MBX, Win2012) was sending emails to Internet using another server (a kerio email server) and outbound internet email was working as expected.
We have now removed the Kerio server, I also removed the kerio_Send_Connector I was using to send emails to internet and I also changed the email domain in Exchange to be authoritative. I created a new Internet send connector with default values, but the same
bad behavior is present.
Our Exchange 2013 receives emails internally and externally with no problems. The problems are sending emails to Internet. I am suspecting something in the firewall but i need to do some more research.
If from the same Exchange server I telnet to an Internet email host:25 I do get the smtp banner but as soon as I start typing HELO/EHLO I get disconnected and errors are logged.
Errors when sending emails to any emails address (this is from an email sent to google, all others are the same):
Remote Server at aspmx3.googlemail.com (74.125.136.26) returned '400 4.4.7 Message delayed'
7/1/14 9:52:44 a. m. - Remote Server at aspmx3.googlemail.com (74.125.136.26) returned '441 4.4.1 Error encountered while communicating with primary target IP address: "Failed to connect. Winsock error code: 10051, Win32 error code: 10051." Attempted
failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts. The last endpoint attempted was 74.125.136.26:25'
I cannot find any references from such Winsock error that are related to Exchange 2013.
So far all email is being queued at the Exchange Server 2013. I am afraid to install CU3 and make things worse.
Thanks for your comments.

Just check if the receive connector settings are set to fine
check the send connector properties and see whether it is set to use DNS to route emails through external DNS/Internal DNS or smart host .
Do a telnet to external domain like hotmail,yahoo and see at what transaction you are getting an error
Enable verbose logging, restart the transport service and check if you get the same error in the verbose logs as well
Get in touch with the ISP and see if the port 25 for Outbound SMTP is opened.
YOu can check if SMTP Proxy is enabled in the firewall. If so disable the SMTP proxy in the firewall and check.
Good Luck!!
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question.
That will encourage me - and others - to take time out to help you.
Regards,
Sathish

Error while downloading iphone firmware update (error code -3254)

Hey guys,
I am using the German versions of iTunes and the iPhone. When I connect the iPhone to my machine, iTunes starts up and proceeds to inform me that a new firmware update is available. After the license agreement is confirmed, nothing seems to happen for a few sceonds. Then, an error message pops up which tells me that "an unknown error has occured". The error code is -3254.
I searched Google and these forums for variations of this problem, but couldn't find anything suitable. The error code is not mentioned anywhere.
My iTunes version is 7.6.1.9 (running on Windows XP)
My iPhone has firmware version 1.1.3 (failed while upgrading to version 1.1.4)
I found out that similar errors can be caused by firewall misconfigurations, but the built-in iTunes diagnosis tool didn't report any connection problems (I also temporarily opened all of my router UDP ports, didn't help at all).
Any help would be appreciated.

I'm having the same problem. The download finishes and then it says an unknown error occurred. It says it has something to do with my network connection, but I don't think that's the problem.
Did you find a solution yet?
I tried to reinstall iTunes but it didn't work.

Transport Controll Program tp ended with error code 0012

we have 3 instances 1 DEV 2 TEST 3 PROD.
in TCODE:STMS by clicking 'system overview' icon
all systems are showing and domain controller is PROD,
and <u>Test System also defined as Transport Domain Cotroller.</u>
earlier STMS scenario: Transport Route is from DEV to PROD system not to the TEST system.
what I have done:
deleted the Transpor Domain Controller of the TEST system and kept as test system.
create routes from DEV to TEST to PROD.
present STMS problem:
when I am sending Request from the DEV to TEST Request going smootly. but at TEST sytem while importing the Request it is giving the ERROR as "<b>Transport control program tp ended with error code 0012</b>"
please help out me....as soon as possible.

This is definitely the wrong forum for your post. Please repost properly.
Regards, Klaus

I get an Error code Ox80090318 when I try to connect to iTunes Store, how can i fix this problem?

I'm using a Dell inpirion mini laptop, and I connected using a AT&T sim card, I download the AT&T Communication Manager Software and when i try to go to the iTunes Store it gives me the Error Code Ox80090318, it reads that to check my network connection, How ever I do have access to the internet. any ideas? Thank you. DanDiMan007

Thank You Eric, I contacted Cisco, they have nothing for Maverick OS.. too new for them.. It still works fine but I can't access my router settings If needed if I needed to view my settings, to change a password or add more guest access. Right now if I had to do something, They said they would have to make the changes locally through their website and there would be a fee because I'm out of warranty.. Since I'm able to still connect since upgrading to Maverick, I assumed Apple included a patch or something in the Maverick upgrade..

Re: Windows Vista and 7 / Error Code in Windows 7 Home Premium

Just purchased my first laptop and am attempting to connect to the internet via a DSL GNET Modem using PPPoE. When I attempt to connect to the internet I get Error Code 651: The modem (or other connecting device) has reported an error. Any ideas on a fix for this. Odd to get a new system and an error code so soon.
System Overview:
Toshiba Satellite Notebook
AMD Phenom (tm) II N870 Triple Core Processor
2.30 GHZ
64 Bit OS
Sent via IPAD

Im 100% sure this error is not caused by your new notebook. Im also 100% sure that all ports on your notebook work properly. You can check this in device manager. Is some problem there?
This modem is not known to me but, generally speaking, using LAN cable there should not be any problem if your modem is configured properly. With WLAN is the same.
Have you tested functionality on some other LAN or WLAN network (different DSL router)?
By the way: which notebook model do you have exactly?

Router Error Codes

Similar Messages

Maybe you are looking for