Router fail to boot properly

SNMP-5-COLDSTART: SNMP agent on host abuja_router is undergoing a cold start
SSH-5-ENABLED: SSH 2.0 has been enabled

Hi jimoh,
there is nothing wrong with this log, just means that router, probably has lost its power and regained again. You can verify the last reload reason issuing the "sh ver" command.
Regards,
Alessandro

Similar Messages

  • Mac Book fails to boot properly after EFI Firmware 27 update

    hi
    I have a strange boot issue having (tried) to install EFI 2.7 update.
    When I restart the laptop, it 'chimes', displays a grey screen ... then chimes, displays a grey screen , ... for ever
    I hit the bower (off) button for 5 secs or thereabouts, and restart ... same thing
    I do this 4 times and finally it reboots.
    But the EFI update still appears as needing to be installed (software update tells me it is not installed).  Update history shows however that it IS installed.
    I can go through this process any number of times ...  I now have Software Update history showing quite a few installs opf the EFI 2.7 update.
    If I just do a restart WITHOUT installing, I also go through the same fail to restart / fail to start / ... / eventually restart sequence.
    So it seems now that the laptop will only start after 4 failed restarts and finally it starts ...
    After starting it all appears to be perfectly fine.
    Nothing strange in the console logs that I can see.  The failed reboots don't seem to register in the console logs - I suspect that the failure to restart is pretty early on in the boot sequence, well before it tries to load any semblance of the OSX kernel.  It is almost as if it is trying to boot from someplace other than the disk ... until eventually it gives up and tries the disk.  (I have tried booting with and without network cable - no difference)  I don't know enough about mac bootup sequences to know if there is some config/setting that is screwed up causing this odd behaviour.  I sirt of feel it must be setup/software related, but could be wrong.
    Odd.
    Any ideas?
    - chris

    I have a MC721LL/A early 2011 15.4" MacBook Pro i7. After I installed this firmware update my Mail would not load saying the version I was trying to start was not compatible with the OSX version (not sure whether this was an OSX update issue which I think I did at the same time). But the biggest problem I have is that I cannot boot my machine. It boots to the Apple logo and then emits 3 beeps repeatedly. I am on vacation in Osaka, Japan and the Apple Store here told me after running some analytics that the logic board is not seeing the RAM. After reseating the RAM multiple times (both original and replacement DIMMS), it still won't boot. The Genius Bar guy said very nicely that it is out of warranty and needs a new logic board, costing over $500 and taking a week at the factory. He recommended spending the money on a new MacBook instead. Since my machine is 15 months old, I am not very happy about this. The machine was absolutely fine before the firmware upgrade. I will wait till I get back to the US and get a second opinion from my local Apple Store. I can't accept that a 15 month old MacBook Pro very lightly used can develop such a catastrophic failure.

  • Mac won't boot properly unless in safe mode

    Recently I updated my MacBook Pro to OS  X Yosemite. I then started the process of the data encryption.
    I don't know what happened, but maybe the encryption failed, because now every time I turn my mac on, it won't boot properly unless it's in safe mode.
    Either it will have a black screen with a visible cursor, or just the desktop with no dock or the bar along the top and no icons, or it does boot up properly, but works extremely slowly. Like if I was to press the apple symbol on the top-right of the screen, it would take 5 minutes to actually open it. Nothing works properly.
    And so I opened up my system preferences, and discovered that the Encryption is stuck on half-finished. But I can't stop it. If I try to turn encryption off it says I have to wait till it's finished. But it never does, the progress bar never moves.
    If I open System Preferences while in Safe Mode, the progress bar for Encryption is grey, and underneath it says "connect to power to continue encryption". But it IS connected to power.
    Have I stuffed my Mac? Is there a way to get it working again?

    1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
    Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
    2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
    There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
    3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
    You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
    In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
    You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
    Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
    4. Here's a summary of what you need to do, if you choose to proceed:
    ☞ Copy a line of text in this window to the Clipboard.
    ☞ Paste into the window of another application.
    ☞ Wait for the test to run. It usually takes a few minutes.
    ☞ Paste the results, which will have been copied automatically, back into a reply on this page.
    The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
    5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
    6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
    7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
    Triple-click anywhere in the line of text below on this page to select it:
    PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx ' ' 879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 2883943871 3873345487 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n   "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n   [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n   ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */   /;' ' s/^.+ |\(.+\)$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne 'Goog|ksadm|probe|Roame|SMC:|smcD|sserti|suhel| VALI|ver-r|xpma' -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|NVDA\(|pagin|proc: t|Roamed|rror|SL|TCON|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 54 12 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
    Copy the selected text to the Clipboard by pressing the key combination command-C.
    8. Launch the built-in Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
    9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
    exec bash
    and press return. Then paste the script again.
    10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return  three times at the password prompt. Again, the script will still run.
    If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
    11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
    [Process completed]
    to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
    12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
    At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
    If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
    13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
    14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
    Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

  • Random I/O errors (hdd) and failing to boot, Windows not affected

    I'm experiencing lots of I/O errors when booting and running my Linux partition. I am dual booting Windows 7 (x86_64) and Arch Linux (i686) on a single HDD.
    Im using a Lenovo Ideapad G505s with a Seagate ST1000LM HDD and an SDD currently not in use.
    Partition layout:
    NAME FSTYPE LABEL UUID MOUNTPOINT
    sda
    ├─sda1 ntfs System Reserved D8B40750B4073094
    ├─sda2 ntfs 00EA107FEA107360
    └─sda3 ext3 b753e7d2-6a23-4c20-8fa7-bf281a4a09e4 /
    sr0
    All three are primary partitions. Using ext4 yields the exact same result.
    The problem is easy to reproduce:
    Install Windows 7 to first half of HDD and Arch on the second half
    At first Arch works fine but over the next couple of days increasingly more I/O errors show up and at some point the system fails to boot
    Windows seems to work just fine
    Dmesg output:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.16.2-1-ARCH (nobody@var-lib-archbuild-testing-i686-tobias) (gcc version 4.9.1 (GCC) ) #1 SMP PREEMPT Sat Sep 6 13:13:35 CEST 2014
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000009555dfff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009555e000-0x0000000095d5efff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000095d5f000-0x0000000095dbbfff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000095dbc000-0x00000000966bbfff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000966bc000-0x000000009f8befff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009f8bf000-0x000000009fabefff] reserved
    [ 0.000000] BIOS-e820: [mem 0x000000009fabf000-0x000000009fbbefff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x000000009fbbf000-0x000000009fbfefff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x000000009fbff000-0x000000009fbfffff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000009fc00000-0x00000000cfffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed80000-0x00000000fed80fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000022effffff] usable
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] SMBIOS 2.7 present.
    [ 0.000000] DMI: LENOVO 20255/Lenovo G505s, BIOS 83CN35WW(V2.05) 12/06/2013
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] e820: last_pfn = 0x9fc00 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-FFFFF write-through
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000000 mask FFFF80000000 write-back
    [ 0.000000] 1 base 000080000000 mask FFFFE0000000 write-back
    [ 0.000000] 2 base 00009FBBD000 mask FFFFFFFFF000 uncachable
    [ 0.000000] 3 base 0000FFC00000 mask FFFFFFC00000 write-protect
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] TOM2: 000000022f000000 aka 8944M
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] found SMP MP-table at [mem 0x000fe1b0-0x000fe1bf] mapped at [c00fe1b0]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] initial memory mapped: [mem 0x00000000-0x01bfffff]
    [ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0x37000000-0x373fffff]
    [ 0.000000] [mem 0x37000000-0x373fffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x30000000-0x36ffffff]
    [ 0.000000] [mem 0x30000000-0x36ffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x2fffffff]
    [ 0.000000] [mem 0x00100000-0x003fffff] page 4k
    [ 0.000000] [mem 0x00400000-0x2fffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x37400000-0x377fdfff]
    [ 0.000000] [mem 0x37400000-0x377fdfff] page 4k
    [ 0.000000] BRK [0x01798000, 0x01798fff] PGTABLE
    [ 0.000000] RAMDISK: [mem 0x7fcaf000-0x7fffffff]
    [ 0.000000] Allocated new RAMDISK: [mem 0x374ad000-0x377fd0d0]
    [ 0.000000] Move RAMDISK from [mem 0x7fcaf000-0x7ffff0d0] to [mem 0x374ad000-0x377fd0d0]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x000FE020 000024 (v02 LENOVO)
    [ 0.000000] ACPI: XSDT 0x9FBFE120 000094 (v01 LENOVO CB-01 00000001 01000013)
    [ 0.000000] ACPI: FACP 0x9FBFB000 00010C (v05 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: DSDT 0x9FBEA000 00CA66 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: FACS 0x9FB7C000 000040
    [ 0.000000] ACPI: SLIC 0x9FBFD000 000176 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: UEFI 0x9FBFC000 000236 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: HPET 0x9FBFA000 000038 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: APIC 0x9FBF9000 000084 (v03 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: MCFG 0x9FBF8000 00003C (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: ASF! 0x9FBF7000 0000A5 (v32 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: BOOT 0x9FBE9000 000028 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: WDRT 0x9FBE8000 000047 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: WDAT 0x9FBE7000 0001AC (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: FPDT 0x9FBE5000 000044 (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: MSDM 0x9FBE4000 000055 (v03 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x9FBE3000 000B9C (v01 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: SSDT 0x9FBE1000 001F6E (v02 LENOVO CB-01 00000001 ACPI 00040000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 1668MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] BRK [0x01799000, 0x01799fff] PGTABLE
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] Normal [mem 0x01000000-0x377fdfff]
    [ 0.000000] HighMem [mem 0x377fe000-0x9fbfffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0x9555dfff]
    [ 0.000000] node 0: [mem 0x95d5f000-0x95dbbfff]
    [ 0.000000] node 0: [mem 0x966bc000-0x9f8befff]
    [ 0.000000] node 0: [mem 0x9fbff000-0x9fbfffff]
    [ 0.000000] On node 0 totalpages: 649053
    [ 0.000000] free_area_init_node: node 0, pgdat c161c180, node_mem_map f60b5020
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 223230 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 3337 pages used for memmap
    [ 0.000000] HighMem zone: 421825 pages, LIFO batch:31
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x10] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x11] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x12] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x13] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x10228210 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
    [ 0.000000] e820: [mem 0xd0000000-0xf7ffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 14 pages/cpu @f6071000 s33344 r0 d24000 u57344
    [ 0.000000] pcpu-alloc: s33344 r0 d24000 u57344 alloc=14*4096
    [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 647277
    [ 0.000000] Kernel command line: BOOT_IMAGE=../vmlinuz-linux root=/dev/sda3 rw radeon.dpm=1 initrd=../initramfs-linux.img
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
    [ 0.000000] allocated 5234680 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (000377fe:0009fc00)
    [ 0.000000] Initializing Movable for node 0 (00000000:00000000)
    [ 0.000000] Memory: 2558328K/2596212K available (4512K kernel code, 483K rwdata, 1328K rodata, 568K init, 824K bss, 37884K reserved, 1687300K highmem)
    [ 0.000000] virtual kernel memory layout:
    fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    .init : 0xc1630000 - 0xc16be000 ( 568 kB)
    .data : 0xc146853a - 0xc162ec80 (1817 kB)
    .text : 0xc1000000 - 0xc146853a (4513 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
    [ 0.000000] NR_IRQS:2304 nr_irqs:712 16
    [ 0.000000] CPU 0 irqstacks, hard=f5408000 soft=f540a000
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration using PIT
    [ 0.000000] tsc: Detected 1896.408 MHz processor
    [ 0.000028] Calibrating delay loop (skipped), value calculated using timer frequency.. 3794.85 BogoMIPS (lpj=6321360)
    [ 0.000032] pid_max: default: 32768 minimum: 301
    [ 0.000037] ACPI: Core revision 20140424
    [ 0.009582] ACPI: All ACPI Tables successfully acquired
    [ 0.015209] Security Framework initialized
    [ 0.015217] Yama: becoming mindful.
    [ 0.015230] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.015233] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
    [ 0.015472] Initializing cgroup subsys memory
    [ 0.015491] Initializing cgroup subsys devices
    [ 0.015498] Initializing cgroup subsys freezer
    [ 0.015502] Initializing cgroup subsys net_cls
    [ 0.015507] Initializing cgroup subsys blkio
    [ 0.015528] [Firmware Info]: CPU: Re-enabling disabled Topology Extensions Support.
    [ 0.015531] CPU: Physical Processor ID: 0
    [ 0.015532] CPU: Processor Core ID: 0
    [ 0.015536] mce: CPU supports 7 MCE banks
    [ 0.015551] Last level iTLB entries: 4KB 512, 2MB 1024, 4MB 512
    Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 512, 1GB 0
    tlb_flushall_shift: 6
    [ 0.015678] Freeing SMP alternatives memory: 16K (c16be000 - c16c2000)
    [ 0.016347] ftrace: allocating 19356 entries in 38 pages
    [ 0.023471] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.023812] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.056821] smpboot: CPU0: AMD A8-4500M APU with Radeon(tm) HD Graphics (fam: 15, model: 10, stepping: 01)
    [ 0.162662] Performance Events: Fam15h core perfctr, AMD PMU driver.
    [ 0.162668] ... version: 0
    [ 0.162670] ... bit width: 48
    [ 0.162671] ... generic registers: 6
    [ 0.162672] ... value mask: 0000ffffffffffff
    [ 0.162674] ... max period: 00007fffffffffff
    [ 0.162675] ... fixed-purpose events: 0
    [ 0.162676] ... event mask: 000000000000003f
    [ 0.179472] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.186176] CPU 1 irqstacks, hard=f554a000 soft=f554c000
    [ 0.186179] x86: Booting SMP configuration:
    [ 0.186182] .... node #0, CPUs: #1
    [ 0.218942] Initializing CPU#1
    [ 0.218972] [Firmware Info]: CPU: Re-enabling disabled Topology Extensions Support.
    [ 0.226174] CPU 2 irqstacks, hard=f5570000 soft=f5572000
    [ 0.226179] #2
    [ 0.258736] Initializing CPU#2
    [ 0.258760] [Firmware Info]: CPU: Re-enabling disabled Topology Extensions Support.
    [ 0.266174] CPU 3 irqstacks, hard=f559a000 soft=f559c000
    [ 0.266180] #3
    [ 0.276300] Initializing CPU#3
    [ 0.277268] [Firmware Info]: CPU: Re-enabling disabled Topology Extensions Support.
    [ 0.279379] x86: Booted up 1 node, 4 CPUs
    [ 0.279384] smpboot: Total of 4 processors activated (15177.40 BogoMIPS)
    [ 0.280484] devtmpfs: initialized
    [ 0.280769] PM: Registering ACPI NVS region [mem 0x9fabf000-0x9fbbefff] (1048576 bytes)
    [ 0.281973] pinctrl core: initialized pinctrl subsystem
    [ 0.282053] RTC time: 22:28:26, date: 09/21/14
    [ 0.282107] NET: Registered protocol family 16
    [ 0.282225] cpuidle: using governor ladder
    [ 0.282228] cpuidle: using governor menu
    [ 0.282436] ACPI: bus type PCI registered
    [ 0.282439] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.282552] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
    [ 0.282556] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
    [ 0.282558] PCI: Using MMCONFIG for extended config space
    [ 0.282559] PCI: Using configuration type 1 for base access
    [ 0.293370] ACPI: Added _OSI(Module Device)
    [ 0.293374] ACPI: Added _OSI(Processor Device)
    [ 0.293376] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.293378] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.297280] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.301911] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.323484] ACPI: Interpreter enabled
    [ 0.323495] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
    [ 0.323501] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
    [ 0.323519] ACPI: (supports S0 S3 S4 S5)
    [ 0.323522] ACPI: Using IOAPIC for interrupt routing
    [ 0.323762] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.324136] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
    [ 0.324308] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
    [ 0.324511] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness
    [ 0.335527] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.335534] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.335540] acpi PNP0A08:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
    [ 0.335709] acpi PNP0A08:00: ignoring host bridge window [mem 0x000cc000-0x000cffff] (conflicts with Video ROM [mem 0x000c0000-0x000cf1ff])
    [ 0.335713] acpi PNP0A08:00: ignoring host bridge window [mem 0x000d0000-0x000d3fff] (conflicts with Adapter ROM [mem 0x000cf800-0x000d07ff])
    [ 0.335718] acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
    [ 0.335971] PCI host bridge to bus 0000:00
    [ 0.335974] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.335977] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.335985] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.335988] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.335990] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000c3fff]
    [ 0.335992] pci_bus 0000:00: root bus resource [mem 0x000c4000-0x000c7fff]
    [ 0.335994] pci_bus 0000:00: root bus resource [mem 0x000c8000-0x000cbfff]
    [ 0.335996] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff]
    [ 0.335998] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff]
    [ 0.336000] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff]
    [ 0.336001] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff]
    [ 0.336003] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff]
    [ 0.336005] pci_bus 0000:00: root bus resource [mem 0x000e8000-0x000ebfff]
    [ 0.336007] pci_bus 0000:00: root bus resource [mem 0x000ec000-0x000effff]
    [ 0.336009] pci_bus 0000:00: root bus resource [mem 0xd0000000-0xf7ffffff]
    [ 0.336011] pci_bus 0000:00: root bus resource [mem 0xfc000000-0xfed3ffff]
    [ 0.336013] pci_bus 0000:00: root bus resource [mem 0xfed45000-0xffffffff]
    [ 0.336022] pci 0000:00:00.0: [1022:1410] type 00 class 0x060000
    [ 0.336199] pci 0000:00:01.0: [1002:9903] type 00 class 0x030000
    [ 0.336211] pci 0000:00:01.0: reg 0x10: [mem 0xd0000000-0xdfffffff pref]
    [ 0.336217] pci 0000:00:01.0: reg 0x14: [io 0x4000-0x40ff]
    [ 0.336224] pci 0000:00:01.0: reg 0x18: [mem 0xf0300000-0xf033ffff]
    [ 0.336266] pci 0000:00:01.0: supports D1 D2
    [ 0.336358] pci 0000:00:01.1: [1002:9902] type 00 class 0x040300
    [ 0.336369] pci 0000:00:01.1: reg 0x10: [mem 0xf0344000-0xf0347fff]
    [ 0.336417] pci 0000:00:01.1: supports D1 D2
    [ 0.336509] pci 0000:00:02.0: [1022:1412] type 01 class 0x060400
    [ 0.336560] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
    [ 0.336710] pci 0000:00:04.0: [1022:1414] type 01 class 0x060400
    [ 0.336759] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
    [ 0.336812] pci 0000:00:04.0: System wakeup disabled by ACPI
    [ 0.336867] pci 0000:00:05.0: [1022:1415] type 01 class 0x060400
    [ 0.336916] pci 0000:00:05.0: PME# supported from D0 D3hot D3cold
    [ 0.336970] pci 0000:00:05.0: System wakeup disabled by ACPI
    [ 0.337102] pci 0000:00:10.0: [1022:7814] type 00 class 0x0c0330
    [ 0.337124] pci 0000:00:10.0: reg 0x10: [mem 0xf0348000-0xf0349fff 64bit]
    [ 0.337221] pci 0000:00:10.0: PME# supported from D0 D3hot D3cold
    [ 0.337272] pci 0000:00:10.0: System wakeup disabled by ACPI
    [ 0.337330] pci 0000:00:11.0: [1022:7801] type 00 class 0x010601
    [ 0.337347] pci 0000:00:11.0: reg 0x10: [io 0x4118-0x411f]
    [ 0.337356] pci 0000:00:11.0: reg 0x14: [io 0x4124-0x4127]
    [ 0.337364] pci 0000:00:11.0: reg 0x18: [io 0x4110-0x4117]
    [ 0.337373] pci 0000:00:11.0: reg 0x1c: [io 0x4120-0x4123]
    [ 0.337382] pci 0000:00:11.0: reg 0x20: [io 0x4100-0x410f]
    [ 0.337390] pci 0000:00:11.0: reg 0x24: [mem 0xf034e000-0xf034e7ff]
    [ 0.337516] pci 0000:00:12.0: [1022:7807] type 00 class 0x0c0310
    [ 0.337528] pci 0000:00:12.0: reg 0x10: [mem 0xf034d000-0xf034dfff]
    [ 0.337617] pci 0000:00:12.0: System wakeup disabled by ACPI
    [ 0.337703] pci 0000:00:12.2: [1022:7808] type 00 class 0x0c0320
    [ 0.338061] pci 0000:00:12.2: reg 0x10: [mem 0xf034c000-0xf034c0ff]
    [ 0.340177] pci 0000:00:12.2: supports D1 D2
    [ 0.340179] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.340285] pci 0000:00:13.0: [1022:7807] type 00 class 0x0c0310
    [ 0.340299] pci 0000:00:13.0: reg 0x10: [mem 0xf034b000-0xf034bfff]
    [ 0.340392] pci 0000:00:13.0: System wakeup disabled by ACPI
    [ 0.340458] pci 0000:00:13.2: [1022:7808] type 00 class 0x0c0320
    [ 0.340887] pci 0000:00:13.2: reg 0x10: [mem 0xf034a000-0xf034a0ff]
    [ 0.343004] pci 0000:00:13.2: supports D1 D2
    [ 0.343006] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.343116] pci 0000:00:14.0: [1022:780b] type 00 class 0x0c0500
    [ 0.343284] pci 0000:00:14.2: [1022:780d] type 00 class 0x040300
    [ 0.343303] pci 0000:00:14.2: reg 0x10: [mem 0xf0340000-0xf0343fff 64bit]
    [ 0.343360] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
    [ 0.343454] pci 0000:00:14.3: [1022:780e] type 00 class 0x060100
    [ 0.343595] pci 0000:00:14.4: [1022:780f] type 01 class 0x060401
    [ 0.343659] pci 0000:00:14.4: System wakeup disabled by ACPI
    [ 0.343722] pci 0000:00:18.0: [1022:1400] type 00 class 0x060000
    [ 0.343802] pci 0000:00:18.1: [1022:1401] type 00 class 0x060000
    [ 0.343878] pci 0000:00:18.2: [1022:1402] type 00 class 0x060000
    [ 0.343955] pci 0000:00:18.3: [1022:1403] type 00 class 0x060000
    [ 0.344036] pci 0000:00:18.4: [1022:1404] type 00 class 0x060000
    [ 0.344112] pci 0000:00:18.5: [1022:1405] type 00 class 0x060000
    [ 0.344337] pci 0000:01:00.0: [1002:6663] type 00 class 0x038000
    [ 0.344355] pci 0000:01:00.0: reg 0x10: [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.344367] pci 0000:01:00.0: reg 0x18: [mem 0xf0200000-0xf023ffff 64bit]
    [ 0.344375] pci 0000:01:00.0: reg 0x20: [io 0x3000-0x30ff]
    [ 0.344388] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    [ 0.344446] pci 0000:01:00.0: supports D1 D2
    [ 0.344449] pci 0000:01:00.0: PME# supported from D1 D2 D3hot
    [ 0.349478] pci 0000:00:02.0: PCI bridge to [bus 01]
    [ 0.349488] pci 0000:00:02.0: bridge window [io 0x3000-0x3fff]
    [ 0.349493] pci 0000:00:02.0: bridge window [mem 0xf0200000-0xf02fffff]
    [ 0.349498] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.349615] pci 0000:02:00.0: [1969:10a0] type 00 class 0x020000
    [ 0.349642] pci 0000:02:00.0: reg 0x10: [mem 0xf0100000-0xf013ffff 64bit]
    [ 0.349653] pci 0000:02:00.0: reg 0x18: [io 0x2000-0x207f]
    [ 0.349752] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.356148] pci 0000:00:04.0: PCI bridge to [bus 02]
    [ 0.356157] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
    [ 0.356162] pci 0000:00:04.0: bridge window [mem 0xf0100000-0xf01fffff]
    [ 0.356295] pci 0000:03:00.0: [168c:0036] type 00 class 0x028000
    [ 0.356334] pci 0000:03:00.0: reg 0x10: [mem 0xf0000000-0xf007ffff 64bit]
    [ 0.356393] pci 0000:03:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
    [ 0.356487] pci 0000:03:00.0: supports D1 D2
    [ 0.356490] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.362836] pci 0000:00:05.0: PCI bridge to [bus 03]
    [ 0.362848] pci 0000:00:05.0: bridge window [mem 0xf0000000-0xf00fffff]
    [ 0.363018] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode)
    [ 0.363032] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.363036] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.363039] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.363041] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000c3fff] (subtractive decode)
    [ 0.363044] pci 0000:00:14.4: bridge window [mem 0x000c4000-0x000c7fff] (subtractive decode)
    [ 0.363047] pci 0000:00:14.4: bridge window [mem 0x000c8000-0x000cbfff] (subtractive decode)
    [ 0.363049] pci 0000:00:14.4: bridge window [mem 0x000d4000-0x000d7fff] (subtractive decode)
    [ 0.363052] pci 0000:00:14.4: bridge window [mem 0x000d8000-0x000dbfff] (subtractive decode)
    [ 0.363054] pci 0000:00:14.4: bridge window [mem 0x000dc000-0x000dffff] (subtractive decode)
    [ 0.363057] pci 0000:00:14.4: bridge window [mem 0x000e0000-0x000e3fff] (subtractive decode)
    [ 0.363059] pci 0000:00:14.4: bridge window [mem 0x000e4000-0x000e7fff] (subtractive decode)
    [ 0.363062] pci 0000:00:14.4: bridge window [mem 0x000e8000-0x000ebfff] (subtractive decode)
    [ 0.363064] pci 0000:00:14.4: bridge window [mem 0x000ec000-0x000effff] (subtractive decode)
    [ 0.363067] pci 0000:00:14.4: bridge window [mem 0xd0000000-0xf7ffffff] (subtractive decode)
    [ 0.363069] pci 0000:00:14.4: bridge window [mem 0xfc000000-0xfed3ffff] (subtractive decode)
    [ 0.363072] pci 0000:00:14.4: bridge window [mem 0xfed45000-0xffffffff] (subtractive decode)
    [ 0.363129] pci_bus 0000:00: on NUMA node 0
    [ 0.366581] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.366668] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.366752] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.366834] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.366902] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.366953] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.367003] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.367062] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0
    [ 0.367177] ACPI: Enabled 5 GPEs in block 00 to 1F
    [ 0.367230] ACPI : EC: GPE = 0x3, I/O: command/status = 0x66, data = 0x62
    [ 0.367446] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.367456] vgaarb: loaded
    [ 0.367458] vgaarb: bridge control possible 0000:00:01.0
    [ 0.367505] PCI: Using ACPI for IRQ routing
    [ 0.369255] PCI: pci_cache_line_size set to 64 bytes
    [ 0.369352] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
    [ 0.369355] e820: reserve RAM buffer [mem 0x9555e000-0x97ffffff]
    [ 0.369357] e820: reserve RAM buffer [mem 0x95dbc000-0x97ffffff]
    [ 0.369358] e820: reserve RAM buffer [mem 0x9f8bf000-0x9fffffff]
    [ 0.369360] e820: reserve RAM buffer [mem 0x9fc00000-0x9fffffff]
    [ 0.369516] NetLabel: Initializing
    [ 0.369518] NetLabel: domain hash size = 128
    [ 0.369519] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.369532] NetLabel: unlabeled traffic allowed by default
    [ 0.369583] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.369588] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
    [ 0.371730] Switched to clocksource hpet
    [ 0.378213] pnp: PnP ACPI init
    [ 0.378231] ACPI: bus type PNP registered
    [ 0.378374] system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.378377] system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.378381] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.378616] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.378678] pnp 00:02: Plug and Play ACPI device, IDs MSF0001 PNP0303 (active)
    [ 0.378740] pnp 00:03: Plug and Play ACPI device, IDs ETD061b ETD0001 PNP0f13 (active)
    [ 0.378836] system 00:04: [io 0x0400-0x04cf] could not be reserved
    [ 0.378839] system 00:04: [io 0x04d0-0x04d1] has been reserved
    [ 0.378841] system 00:04: [io 0x04d6] has been reserved
    [ 0.378844] system 00:04: [io 0x0680-0x06ff] has been reserved
    [ 0.378846] system 00:04: [io 0x077a] has been reserved
    [ 0.378848] system 00:04: [io 0x0c00-0x0c01] has been reserved
    [ 0.378850] system 00:04: [io 0x0c14] has been reserved
    [ 0.378853] system 00:04: [io 0x0c50-0x0c52] has been reserved
    [ 0.378855] system 00:04: [io 0x0c6c] has been reserved
    [ 0.378857] system 00:04: [io 0x0c6f] has been reserved
    [ 0.378859] system 00:04: [io 0x0cd0-0x0cdb] has been reserved
    [ 0.378862] system 00:04: [io 0x0840-0x0847] has been reserved
    [ 0.378864] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.378944] system 00:05: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.378947] system 00:05: [mem 0xffc00000-0xffffffff] has been reserved
    [ 0.378950] system 00:05: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.382206] pnp: PnP ACPI: found 6 devices
    [ 0.382211] ACPI: bus type PNP unregistered
    [ 0.420296] pci 0000:03:00.0: can't claim BAR 6 [mem 0xffff0000-0xffffffff pref]: no compatible bridge window
    [ 0.420325] pci 0000:01:00.0: BAR 6: assigned [mem 0xf0240000-0xf025ffff pref]
    [ 0.420328] pci 0000:00:02.0: PCI bridge to [bus 01]
    [ 0.420331] pci 0000:00:02.0: bridge window [io 0x3000-0x3fff]
    [ 0.420335] pci 0000:00:02.0: bridge window [mem 0xf0200000-0xf02fffff]
    [ 0.420339] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.420343] pci 0000:00:04.0: PCI bridge to [bus 02]
    [ 0.420346] pci 0000:00:04.0: bridge window [io 0x2000-0x2fff]
    [ 0.420349] pci 0000:00:04.0: bridge window [mem 0xf0100000-0xf01fffff]
    [ 0.420355] pci 0000:03:00.0: BAR 6: assigned [mem 0xf0080000-0xf008ffff pref]
    [ 0.420357] pci 0000:00:05.0: PCI bridge to [bus 03]
    [ 0.420361] pci 0000:00:05.0: bridge window [mem 0xf0000000-0xf00fffff]
    [ 0.420366] pci 0000:00:14.4: PCI bridge to [bus 04]
    [ 0.420377] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.420380] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.420382] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.420384] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000c3fff]
    [ 0.420386] pci_bus 0000:00: resource 8 [mem 0x000c4000-0x000c7fff]
    [ 0.420388] pci_bus 0000:00: resource 9 [mem 0x000c8000-0x000cbfff]
    [ 0.420391] pci_bus 0000:00: resource 10 [mem 0x000d4000-0x000d7fff]
    [ 0.420393] pci_bus 0000:00: resource 11 [mem 0x000d8000-0x000dbfff]
    [ 0.420395] pci_bus 0000:00: resource 12 [mem 0x000dc000-0x000dffff]
    [ 0.420397] pci_bus 0000:00: resource 13 [mem 0x000e0000-0x000e3fff]
    [ 0.420399] pci_bus 0000:00: resource 14 [mem 0x000e4000-0x000e7fff]
    [ 0.420401] pci_bus 0000:00: resource 15 [mem 0x000e8000-0x000ebfff]
    [ 0.420403] pci_bus 0000:00: resource 16 [mem 0x000ec000-0x000effff]
    [ 0.420405] pci_bus 0000:00: resource 17 [mem 0xd0000000-0xf7ffffff]
    [ 0.420407] pci_bus 0000:00: resource 18 [mem 0xfc000000-0xfed3ffff]
    [ 0.420409] pci_bus 0000:00: resource 19 [mem 0xfed45000-0xffffffff]
    [ 0.420411] pci_bus 0000:01: resource 0 [io 0x3000-0x3fff]
    [ 0.420413] pci_bus 0000:01: resource 1 [mem 0xf0200000-0xf02fffff]
    [ 0.420416] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref]
    [ 0.420418] pci_bus 0000:02: resource 0 [io 0x2000-0x2fff]
    [ 0.420420] pci_bus 0000:02: resource 1 [mem 0xf0100000-0xf01fffff]
    [ 0.420422] pci_bus 0000:03: resource 1 [mem 0xf0000000-0xf00fffff]
    [ 0.420425] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
    [ 0.420427] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
    [ 0.420429] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.420431] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000c3fff]
    [ 0.420433] pci_bus 0000:04: resource 8 [mem 0x000c4000-0x000c7fff]
    [ 0.420435] pci_bus 0000:04: resource 9 [mem 0x000c8000-0x000cbfff]
    [ 0.420437] pci_bus 0000:04: resource 10 [mem 0x000d4000-0x000d7fff]
    [ 0.420439] pci_bus 0000:04: resource 11 [mem 0x000d8000-0x000dbfff]
    [ 0.420441] pci_bus 0000:04: resource 12 [mem 0x000dc000-0x000dffff]
    [ 0.420443] pci_bus 0000:04: resource 13 [mem 0x000e0000-0x000e3fff]
    [ 0.420445] pci_bus 0000:04: resource 14 [mem 0x000e4000-0x000e7fff]
    [ 0.420447] pci_bus 0000:04: resource 15 [mem 0x000e8000-0x000ebfff]
    [ 0.420449] pci_bus 0000:04: resource 16 [mem 0x000ec000-0x000effff]
    [ 0.420451] pci_bus 0000:04: resource 17 [mem 0xd0000000-0xf7ffffff]
    [ 0.420453] pci_bus 0000:04: resource 18 [mem 0xfc000000-0xfed3ffff]
    [ 0.420455] pci_bus 0000:04: resource 19 [mem 0xfed45000-0xffffffff]
    [ 0.420484] NET: Registered protocol family 2
    [ 0.420674] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
    [ 0.420689] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.420717] TCP: Hash tables configured (established 8192 bind 8192)
    [ 0.420733] TCP: reno registered
    [ 0.420736] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.420742] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.420798] NET: Registered protocol family 1
    [ 0.420831] pci 0000:00:01.0: Boot video device
    [ 1.038734] pci 0000:02:00.0: set MSI_INTX_DISABLE_BUG flag
    [ 1.038759] PCI: CLS 64 bytes, default 64
    [ 1.038818] Unpacking initramfs...
    [ 1.112669] Freeing initrd memory: 3396K (f74ad000 - f77fe000)
    [ 1.112753] Simple Boot Flag at 0x44 set to 0x1
    [ 1.113077] perf: AMD NB counters detected
    [ 1.113122] LVT offset 0 assigned for vector 0x400
    [ 1.113138] perf: AMD IBS detected (0x000000ff)
    [ 1.113149] apm: BIOS not found.
    [ 1.113200] Scanning for low memory corruption every 60 seconds
    [ 1.113689] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [ 1.114240] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 1.116388] zbud: loaded
    [ 1.116669] VFS: Disk quotas dquot_6.5.2
    [ 1.116720] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 1.116962] msgmni has been set to 1707
    [ 1.117034] Key type big_key registered
    [ 1.117325] bounce: pool size: 64 pages
    [ 1.117370] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 1.117448] io scheduler noop registered
    [ 1.117452] io scheduler deadline registered
    [ 1.117524] io scheduler cfq registered (default)
    [ 1.118017] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 1.118037] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 1.118114] GHES: HEST is not enabled!
    [ 1.118129] isapnp: Scanning for PnP cards...
    [ 1.513691] isapnp: No Plug & Play device found
    [ 1.513876] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 1.514746] rtc_cmos 00:01: RTC can wake from S4
    [ 1.515007] rtc_cmos 00:01: rtc core: registered rtc_cmos as rtc0
    [ 1.515032] rtc_cmos 00:01: alarms up to one month, 114 bytes nvram, hpet irqs
    [ 1.515076] ledtrig-cpu: registered to indicate activity on CPUs
    [ 1.515246] TCP: cubic registered
    [ 1.515386] NET: Registered protocol family 10
    [ 1.515657] NET: Registered protocol family 17
    [ 1.516096] Using IPI No-Shortcut mode
    [ 1.516269] registered taskstats version 1
    [ 1.516866] Magic number: 14:856:502
    [ 1.516927] rtc_cmos 00:01: setting system clock to 2014-09-21 22:28:27 UTC (1411338507)
    [ 1.517032] PM: Hibernation image not present or could not be loaded.
    [ 1.517281] Freeing unused kernel memory: 568K (c1630000 - c16be000)
    [ 1.517350] Write protecting the kernel text: 4516k
    [ 1.517388] Write protecting the kernel read-only data: 1332k
    [ 1.527560] random: systemd-tmpfile urandom read with 0 bits of entropy available
    [ 1.529660] systemd-udevd[57]: starting version 216
    [ 1.549349] i8042: PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSSG] at 0x60,0x64 irq 1,12
    [ 1.568048] ACPI: bus type USB registered
    [ 1.568103] usbcore: registered new interface driver usbfs
    [ 1.568141] usbcore: registered new interface driver hub
    [ 1.568537] SCSI subsystem initialized
    [ 1.574578] usbcore: registered new device driver usb
    [ 1.593572] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 1.593667] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 1.593746] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 1.594746] ehci-pci: EHCI PCI platform driver
    [ 1.594935] QUIRK: Enable AMD PLL fix
    [ 1.594970] ehci-pci 0000:00:12.2: EHCI Host Controller
    [ 1.594980] ehci-pci 0000:00:12.2: new USB bus registered, assigned bus number 1
    [ 1.594989] ehci-pci 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
    [ 1.595002] ehci-pci 0000:00:12.2: debug port 1
    [ 1.595055] ehci-pci 0000:00:12.2: irq 17, io mem 0xf034c000
    [ 1.595121] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 1.595830] ohci-pci: OHCI PCI platform driver
    [ 1.601895] ehci-pci 0000:00:12.2: USB 2.0 started, EHCI 1.00
    [ 1.602284] libata version 3.00 loaded.
    [ 1.602306] hub 1-0:1.0: USB hub found
    [ 1.602325] hub 1-0:1.0: 5 ports detected
    [ 1.602883] ehci-pci 0000:00:13.2: EHCI Host Controller
    [ 1.602893] ehci-pci 0000:00:13.2: new USB bus registered, assigned bus number 2
    [ 1.602899] ehci-pci 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
    [ 1.602912] ehci-pci 0000:00:13.2: debug port 1
    [ 1.602945] ehci-pci 0000:00:13.2: irq 17, io mem 0xf034a000
    [ 1.612011] ehci-pci 0000:00:13.2: USB 2.0 started, EHCI 1.00
    [ 1.612308] hub 2-0:1.0: USB hub found
    [ 1.612317] hub 2-0:1.0: 5 ports detected
    [ 1.612814] xhci_hcd 0000:00:10.0: xHCI Host Controller
    [ 1.612828] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 3
    [ 1.613042] xhci_hcd 0000:00:10.0: irq 40 for MSI/MSI-X
    [ 1.613048] xhci_hcd 0000:00:10.0: irq 41 for MSI/MSI-X
    [ 1.613052] xhci_hcd 0000:00:10.0: irq 42 for MSI/MSI-X
    [ 1.613056] xhci_hcd 0000:00:10.0: irq 43 for MSI/MSI-X
    [ 1.613060] xhci_hcd 0000:00:10.0: irq 44 for MSI/MSI-X
    [ 1.613374] hub 3-0:1.0: USB hub found
    [ 1.613388] hub 3-0:1.0: 2 ports detected
    [ 1.613609] xhci_hcd 0000:00:10.0: xHCI Host Controller
    [ 1.613614] xhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 4
    [ 1.616754] hub 4-0:1.0: USB hub found
    [ 1.616768] hub 4-0:1.0: 2 ports detected
    [ 1.617093] ohci-pci 0000:00:12.0: OHCI PCI host controller
    [ 1.617107] ohci-pci 0000:00:12.0: new USB bus registered, assigned bus number 5
    [ 1.617152] ohci-pci 0000:00:12.0: irq 18, io mem 0xf034d000
    [ 1.645460] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
    [ 1.673072] hub 5-0:1.0: USB hub found
    [ 1.673098] hub 5-0:1.0: 5 ports detected
    [ 1.673547] ohci-pci 0000:00:13.0: OHCI PCI host controller
    [ 1.673554] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 6
    [ 1.673585] ohci-pci 0000:00:13.0: irq 18, io mem 0xf034b000
    [ 1.729803] hub 6-0:1.0: USB hub found
    [ 1.729831] hub 6-0:1.0: 5 ports detected
    [ 1.730166] ahci 0000:00:11.0: version 3.0
    [ 1.730351] ahci 0000:00:11.0: irq 45 for MSI/MSI-X
    [ 1.730404] ahci 0000:00:11.0: AHCI 0001.0300 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
    [ 1.730409] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
    [ 1.731131] scsi0 : ahci
    [ 1.731321] scsi1 : ahci
    [ 1.731403] ata1: SATA max UDMA/133 abar m2048@0xf034e000 port 0xf034e100 irq 45
    [ 1.731407] ata2: SATA max UDMA/133 abar m2048@0xf034e000 port 0xf034e180 irq 45
    [ 1.962152] usb 1-4: new high-speed USB device number 3 using ehci-pci
    [ 2.115336] tsc: Refined TSC clocksource calibration: 1896.456 MHz
    [ 2.215395] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.215424] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 2.216948] ata2.00: ATAPI: MATSHITADVD-RAM UJ8C2, 1.00, max UDMA/133
    [ 2.218438] ata2.00: configured for UDMA/133
    [ 2.274381] ata1.00: ATA-9: ST1000LM014-1EJ164, LVD3, max UDMA/133
    [ 2.274386] ata1.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 2.318651] ata1.00: configured for UDMA/133
    [ 2.318844] scsi 0:0:0:0: Direct-Access ATA ST1000LM014-1EJ1 LVD3 PQ: 0 ANSI: 5
    [ 2.320735] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ8C2 1.00 PQ: 0 ANSI: 5
    [ 2.337991] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    [ 2.337996] sd 0:0:0:0: [sda] 4096-byte physical blocks
    [ 2.338079] sd 0:0:0:0: [sda] Write Protect is off
    [ 2.338085] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.338151] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.338885] sda: sda1 sda2 sda3
    [ 2.339411] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 2.348995] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
    [ 2.348999] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.349240] sr 1:0:0:0: Attached scsi CD-ROM sr0
    [ 2.395434] usb 3-1: new low-speed USB device number 2 using xhci_hcd
    [ 2.438944] ata1.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x6
    [ 2.438989] ata1.00: irq_stat 0x40000008
    [ 2.439030] ata1.00: failed command: READ FPDMA QUEUED
    [ 2.439074] ata1.00: cmd 60/08:38:18:08:00/00:00:00:00:00/40 tag 7 ncq 4096 in
    res 41/84:08:18:08:00/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 2.439127] ata1.00: status: { DRDY ERR }
    [ 2.439166] ata1.00: error: { ICRC ABRT }
    [ 2.439207] ata1: hard resetting link
    [ 2.555934] usb 3-1: ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 2.555943] usb 3-1: ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes
    [ 2.559635] hidraw: raw HID events driver (C) Jiri Kosina
    [ 2.586950] usbcore: registered new interface driver usbhid
    [ 2.586953] usbhid: USB HID core driver
    [ 2.588065] input: Microsoft Comfort Curve Keyboard 3000 as /devices/pci0000:00/0000:00:10.0/usb3/3-1/3-1:1.0/0003:045E:0780.0001/input/input2
    [ 2.588153] hid-generic 0003:045E:0780.0001: input,hidraw0: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 3000] on usb-0000:00:10.0-1/input0
    [ 2.594030] input: Microsoft Comfort Curve Keyboard 3000 as /devices/pci0000:00/0000:00:10.0/usb3/3-1/3-1:1.1/0003:045E:0780.0002/input/input3
    [ 2.594150] hid-generic 0003:045E:0780.0002: input,hidraw1: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 3000] on usb-0000:00:10.0-1/input1
    [ 2.662213] usb 2-2: new high-speed USB device number 2 using ehci-pci
    [ 2.915446] usb 5-1: new low-speed USB device number 2 using ohci-pci
    [ 2.925441] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 3.039928] ata1.00: configured for UDMA/133
    [ 3.039955] ata1: EH complete
    [ 3.081259] input: USB Mouse as /devices/pci0000:00/0000:00:12.0/usb5/5-1/5-1:1.0/0003:05E3:1205.0003/input/input4
    [ 3.081368] hid-generic 0003:05E3:1205.0003: input,hidraw2: USB HID v1.10 Mouse [USB Mouse ] on usb-0000:00:12.0-1/input0
    [ 3.089081] ata1.00: exception Emask 0x0 SAct 0x40000 SErr 0x0 action 0x6
    [ 3.089128] ata1.00: irq_stat 0x40000008
    [ 3.089168] ata1.00: failed command: READ FPDMA QUEUED
    [ 3.089212] ata1.00: cmd 60/08:90:78:28:03/00:00:00:00:00/40 tag 18 ncq 4096 in
    res 41/84:08:7c:28:03/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 3.089265] ata1.00: status: { DRDY ERR }
    [ 3.089304] ata1.00: error: { ICRC ABRT }
    [ 3.089346] ata1: hard resetting link
    [ 3.115583] Switched to clocksource tsc
    [ 3.575598] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 3.694602] ata1.00: configured for UDMA/133
    [ 3.694621] ata1: EH complete
    [ 3.809120] ata1.00: exception Emask 0x0 SAct 0x1e00 SErr 0x0 action 0x6
    [ 3.809168] ata1.00: irq_stat 0x40000008
    [ 3.809208] ata1.00: failed command: READ FPDMA QUEUED
    [ 3.809251] ata1.00: cmd 60/08:48:10:08:00/00:00:00:00:00/40 tag 9 ncq 4096 in
    res 41/84:08:10:08:00/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 3.809305] ata1.00: status: { DRDY ERR }
    [ 3.809343] ata1.00: error: { ICRC ABRT }
    [ 3.809385] ata1: hard resetting link
    [ 4.295566] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
    [ 4.404835] ata1.00: configured for UDMA/133
    [ 4.404858] ata1: EH complete
    [ 4.453715] ata1.00: exception Emask 0x0 SAct 0x1fe000 SErr 0x0 action 0x0
    [ 4.453760] ata1.00: irq_stat 0x40000008
    [ 4.453799] ata1.00: failed command: READ FPDMA QUEUED
    [ 4.453842] ata1.00: cmd 60/80:68:80:08:00/01:00:00:00:00/40 tag 13 ncq 196608 in
    res 41/40:80:b8:09:00/00:01:00:00:00/00 Emask 0x409 (media error) <F>
    [ 4.453894] ata1.00: status: { DRDY ERR }
    [ 4.453932] ata1.00: error: { UNC }
    [ 4.637639] ata1.00: configured for UDMA/133
    [ 4.637688] sd 0:0:0:0: [sda] Unhandled sense code
    [ 4.637691] sd 0:0:0:0: [sda]
    [ 4.637693] Result: hostbyte=0x00 driverbyte=0x08
    [ 4.637695] sd 0:0:0:0: [sda]
    [ 4.637697] Sense Key : 0x3 [current] [descriptor]
    [ 4.637700] Descriptor sense data with sense descriptors (in hex):
    [ 4.637702] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 4.637710] 00 00 09 b8
    [ 4.637714] sd 0:0:0:0: [sda]
    [ 4.637716] ASC=0x11 ASCQ=0x4
    [ 4.637718] sd 0:0:0:0: [sda] CDB:
    [ 4.637719] cdb[0]=0x28: 28 00 00 00 08 80 00 01 80 00
    [ 4.637727] end_request: I/O error, dev sda, sector 2488
    [ 4.637786] Buffer I/O error on device sda1, logical block 55
    [ 4.637826] Buffer I/O error on device sda1, logical block 56
    [ 4.637866] Buffer I/O error on device sda1, logical block 57
    [ 4.637905] Buffer I/O error on device sda1, logical block 58
    [ 4.637945] Buffer I/O error on device sda1, logical block 59
    [ 4.637984] Buffer I/O error on device sda1, logical block 60
    [ 4.638024] Buffer I/O error on device sda1, logical block 61
    [ 4.638063] Buffer I/O error on device sda1, logical block 62
    [ 4.638105] Buffer I/O error on device sda1, logical block 63
    [ 4.638188] ata1: EH complete
    [ 4.879313] ata1: limiting SATA link speed to 3.0 Gbps
    [ 4.879320] ata1.00: exception Emask 0x0 SAct 0x4000 SErr 0x0 action 0x6
    [ 4.879364] ata1.00: irq_stat 0x40000008
    [ 4.879404] ata1.00: failed command: READ FPDMA QUEUED
    [ 4.879448] ata1.00: cmd 60/08:70:50:2b:03/00:00:00:00:00/40 tag 14 ncq 4096 in
    res 41/84:08:50:2b:03/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 4.879502] ata1.00: status: { DRDY ERR }
    [ 4.879540] ata1.00: error: { ICRC ABRT }
    [ 4.879583] ata1: hard resetting link
    [ 5.365653] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
    [ 5.469816] ata1.00: configured for UDMA/133
    [ 5.469845] ata1: EH complete
    [ 5.582799] ata1.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x6
    [ 5.582859] ata1.00: irq_stat 0x40000008
    [ 5.582900] ata1.00: failed command: READ FPDMA QUEUED
    [ 5.582943] ata1.00: cmd 60/08:38:18:0b:00/00:00:00:00:00/40 tag 7 ncq 4096 in
    res 41/84:08:19:0b:00/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 5.582997] ata1.00: status: { DRDY ERR }
    [ 5.583036] ata1.00: error: { ICRC ABRT }
    [ 5.583078] ata1: hard resetting link
    [ 6.069015] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
    [ 6.191135] ata1.00: configured for UDMA/133
    [ 6.191166] ata1: EH complete
    [ 6.256026] ata1.00: exception Emask 0x0 SAct 0x8000 SErr 0x0 action 0x6
    [ 6.256073] ata1.00: irq_stat 0x40000008
    [ 6.256114] ata1.00: failed command: READ FPDMA QUEUED
    [ 6.256158] ata1.00: cmd 60/08:78:00:38:03/00:00:00:00:00/40 tag 15 ncq 4096 in
    res 41/84:08:02:38:03/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 6.256212] ata1.00: status: { DRDY ERR }
    [ 6.256250] ata1.00: error: { ICRC ABRT }
    [ 6.256292] ata1: hard resetting link
    [ 6.742436] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
    [ 6.845773] ata1.00: configured for UDMA/133
    [ 6.845806] ata1: EH complete
    [ 6.986177] ata1.00: exception Emask 0x0 SAct 0x80000 SErr 0x0 action 0x6
    [ 6.986223] ata1.00: irq_stat 0x40000008
    [ 6.986264] ata1.00: failed command: READ FPDMA QUEUED
    [ 6.986308] ata1.00: cmd 60/08:98:b0:f8:b5/00:00:58:00:00/40 tag 19 ncq 4096 in
    res 41/84:08:b0:f8:b5/00:00:58:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 6.986360] ata1.00: status: { DRDY ERR }
    [ 6.986399] ata1.00: error: { ICRC ABRT }
    [ 6.986440] ata1: hard resetting link
    [ 7.472592] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
    [ 7.578097] ata1.00: configured for UDMA/133
    [ 7.578124] ata1: EH complete
    [ 7.587216] random: nonblocking pool is initialized
    [ 7.602800] ata1: limiting SATA link speed to 1.5 Gbps
    [ 7.602806] ata1.00: exception Emask 0x0 SAct 0x800000 SErr 0x0 action 0x6
    [ 7.602850] ata1.00: irq_stat 0x40000008
    [ 7.602889] ata1.00: failed command: READ FPDMA QUEUED
    [ 7.602931] ata1.00: cmd 60/08:b8:c8:58:b6/00:00:58:00:00/40 tag 23 ncq 4096 in
    res 41/84:08:cc:58:b6/00:00:58:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 7.602982] ata1.00: status: { DRDY ERR }
    [ 7.603020] ata1.00: error: { ICRC ABRT }
    [ 7.603061] ata1: hard resetting link
    [ 8.089174] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 8.188490] ata1.00: configured for UDMA/133
    [ 8.188517] ata1: EH complete
    [ 8.216300] ata1.00: exception Emask 0x0 SAct 0x2000000 SErr 0x0 action 0x6
    [ 8.216361] ata1.00: irq_stat 0x40000008
    [ 8.216402] ata1.00: failed command: READ FPDMA QUEUED
    [ 8.216446] ata1.00: cmd 60/08:c8:d0:78:b6/00:00:58:00:00/40 tag 25 ncq 4096 in
    res 41/84:08:d0:78:b6/00:00:58:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 8.216500] ata1.00: status: { DRDY ERR }
    [ 8.216539] ata1.00: error: { ICRC ABRT }
    [ 8.216581] ata1: hard resetting link
    [ 8.702603] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 8.809726] ata1.00: configured for UDMA/133
    [ 8.809758] ata1: EH complete
    [ 8.836250] ata1.00: exception Emask 0x0 SAct 0x8000000 SErr 0x0 action 0x6
    [ 8.836295] ata1.00: irq_stat 0x40000008
    [ 8.836335] ata1.00: failed command: READ FPDMA QUEUED
    [ 8.836377] ata1.00: cmd 60/08:d8:d8:98:b6/00:00:58:00:00/40 tag 27 ncq 4096 in
    res 41/84:08:d8:98:b6/00:00:58:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 8.836429] ata1.00: status: { DRDY ERR }
    [ 8.836467] ata1.00: error: { ICRC ABRT }
    [ 8.836507] ata1: hard resetting link
    [ 9.322654] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 9.430994] ata1.00: configured for UDMA/133
    [ 9.431018] ata1: EH complete
    [ 9.664088] EXT4-fs (sda3): mounting ext3 file system using the ext4 subsystem
    [ 9.686362] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
    [ 9.837482] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6
    [ 9.837542] ata1.00: irq_stat 0x40000008
    [ 9.837583] ata1.00: failed command: READ FPDMA QUEUED
    [ 9.837626] ata1.00: cmd 60/08:28:20:08:89/00:00:5e:00:00/40 tag 5 ncq 4096 in
    res 41/84:08:20:08:89/00:00:5e:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 9.837680] ata1.00: status: { DRDY ERR }
    [ 9.837719] ata1.00: error: { ICRC ABRT }
    [ 9.837761] ata1: hard resetting link
    [ 10.322740] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 10.515900] ata1.00: configured for UDMA/133
    [ 10.515972] sd 0:0:0:0: [sda]
    [ 10.515975] Result: hostbyte=0x00 driverbyte=0x08
    [ 10.515978] sd 0:0:0:0: [sda]
    [ 10.515979] Sense Key : 0xb [current] [descriptor]
    [ 10.515983] Descriptor sense data with sense descriptors (in hex):
    [ 10.515984] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 10.515992] 5e 89 08 20
    [ 10.515997] sd 0:0:0:0: [sda]
    [ 10.515998] ASC=0x47 ASCQ=0x0
    [ 10.516001] sd 0:0:0:0: [sda] CDB:
    [ 10.516002] cdb[0]=0x28: 28 00 5e 89 08 20 00 00 08 00
    [ 10.516010] end_request: I/O error, dev sda, sector 1586038816
    [ 10.516148] ata1: EH complete
    [ 10.529733] ata1.00: limiting speed to UDMA/100:PIO4
    [ 10.529740] ata1.00: exception Emask 0x0 SAct 0x7fffff1f SErr 0x0 action 0x6
    [ 10.529786] ata1.00: irq_stat 0x40000008
    [ 10.529826] ata1.00: failed command: READ FPDMA QUEUED
    [ 10.529870] ata1.00: cmd 60/08:40:d0:08:89/00:00:5e:00:00/40 tag 8 ncq 4096 in
    res 41/84:08:d4:08:89/00:00:5e:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 10.529924] ata1.00: status: { DRDY ERR }
    [ 10.529962] ata1.00: error: { ICRC ABRT }
    [ 10.530004] ata1: hard resetting link
    [ 11.016129] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 11.139673] ata1.00: configured for UDMA/100
    [ 11.139723] sd 0:0:0:0: [sda]
    [ 11.139725] Result: hostbyte=0x00 driverbyte=0x08
    [ 11.139728] sd 0:0:0:0: [sda]
    [ 11.139730] Sense Key : 0xb [current] [descriptor]
    [ 11.139733] Descriptor sense data with sense descriptors (in hex):
    [ 11.139735] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 11.139743] 5e 89 08 d4
    [ 11.139747] sd 0:0:0:0: [sda]
    [ 11.139749] ASC=0x47 ASCQ=0x0
    [ 11.139751] sd 0:0:0:0: [sda] CDB:
    [ 11.139753] cdb[0]=0x28: 28 00 5e 89 08 d0 00 00 08 00
    [ 11.139761] end_request: I/O error, dev sda, sector 1586038992
    [ 11.139889] ata1: EH complete
    [ 11.153122] ata1.00: exception Emask 0x0 SAct 0x7fffffc1 SErr 0x0 action 0x6
    [ 11.153169] ata1.00: irq_stat 0x40000008
    [ 11.153210] ata1.00: failed command: READ FPDMA QUEUED
    [ 11.153253] ata1.00: cmd 60/08:30:28:08:89/00:00:5e:00:00/40 tag 6 ncq 4096 in
    res 41/84:08:28:08:89/00:00:5e:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 11.153306] ata1.00: status: { DRDY ERR }
    [ 11.153345] ata1.00: error: { ICRC ABRT }
    [ 11.153386] ata1: hard resetting link
    [ 11.639485] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 11.749884] ata1.00: configured for UDMA/100
    [ 11.749918] sd 0:0:0:0: [sda]
    [ 11.749920] Result: hostbyte=0x00 driverbyte=0x08
    [ 11.749923] sd 0:0:0:0: [sda]
    [ 11.749925] Sense Key : 0xb [current] [descriptor]
    [ 11.749928] Descriptor sense data with sense descriptors (in hex):
    [ 11.749930] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 11.749938] 5e 89 08 28
    [ 11.749942] sd 0:0:0:0: [sda]
    [ 11.749944] ASC=0x47 ASCQ=0x0
    [ 11.749946] sd 0:0:0:0: [sda] CDB:
    [ 11.749948] cdb[0]=0x28: 28 00 5e 89 08 28 00 00 08 00
    [ 11.749956] end_request: I/O error, dev sda, sector 1586038824
    [ 11.750093] ata1: EH complete
    [ 11.763159] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6
    [ 11.763206] ata1.00: irq_stat 0x40000008
    [ 11.763247] ata1.00: failed command: READ FPDMA QUEUED
    [ 11.763290] ata1.00: cmd 60/08:28:c8:08:89/00:00:5e:00:00/40 tag 5 ncq 4096 in
    res 41/84:08:c8:08:89/00:00:5e:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 11.763343] ata1.00: status: { DRDY ERR }
    [ 11.763382] ata1.00: error: { ICRC ABRT }
    [ 11.763424] ata1: hard resetting link
    [ 12.249523] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 12.360321] ata1.00: configured for UDMA/100
    [ 12.360370] sd 0:0:0:0: [sda]
    [ 12.360372] Result: hostbyte=0x00 driverbyte=0x08
    [ 12.360375] sd 0:0:0:0: [sda]
    [ 12.360377] Sense Key : 0xb [current] [descriptor]
    [ 12.360380] Descriptor sense data with sense descriptors (in hex):
    [ 12.360381] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 12.360390] 5e 89 08 c8
    [ 12.360394] sd 0:0:0:0: [sda]
    [ 12.360395] ASC=0x47 ASCQ=0x0
    [ 12.360398] sd 0:0:0:0: [sda] CDB:
    [ 12.360399] cdb[0]=0x28: 28 00 5e 89 08 c8 00 00 08 00
    [ 12.360407] end_request: I/O error, dev sda, sector 1586038984
    [ 12.360543] ata1: EH complete
    [ 12.369958] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6
    [ 12.370005] ata1.00: irq_stat 0x40000008
    [ 12.370045] ata1.00: failed command: READ FPDMA QUEUED
    [ 12.370090] ata1.00: cmd 60/08:28:38:08:89/00:00:63:00:00/40 tag 5 ncq 4096 in
    res 41/84:08:3a:08:89/00:00:63:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 12.370143] ata1.00: status: { DRDY ERR }
    [ 12.370182] ata1.00: error: { ICRC ABRT }
    [ 12.370224] ata1: hard resetting link
    [ 12.856285] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 12.959379] ata1.00: configured for UDMA/100
    [ 12.959426] sd 0:0:0:0: [sda]
    [ 12.959429] Result: hostbyte=0x00 driverbyte=0x08
    [ 12.959432] sd 0:0:0:0: [sda]
    [ 12.959433] Sense Key : 0xb [current] [descriptor]
    [ 12.959437] Descriptor sense data with sense descriptors (in hex):
    [ 12.959438] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 12.959447] 63 89 08 3a
    [ 12.959462] sd 0:0:0:0: [sda]
    [ 12.959464] ASC=0x47 ASCQ=0x0
    [ 12.959466] sd 0:0:0:0: [sda] CDB:
    [ 12.959468] cdb[0]=0x28: 28 00 63 89 08 38 00 00 08 00
    [ 12.959476] end_request: I/O error, dev sda, sector 1669924920
    [ 12.959616] ata1: EH complete
    [ 12.973195] ata1.00: limiting speed to UDMA/33:PIO4
    [ 12.973202] ata1.00: exception Emask 0x0 SAct 0x7fffffff SErr 0x0 action 0x6
    [ 12.973247] ata1.00: irq_stat 0x40000008
    [ 12.973287] ata1.00: failed command: READ FPDMA QUEUED
    [ 12.973331] ata1.00: cmd 60/08:30:c0:08:89/00:00:5e:00:00/40 tag 6 ncq 4096 in
    res 41/84:08:c0:08:89/00:00:5e:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 12.973384] ata1.00: status: { DRDY ERR }
    [ 12.973423] ata1.00: error: { ICRC ABRT }
    [ 12.973464] ata1: hard resetting link
    [ 13.459735] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 13.569691] ata1.00: configured for UDMA/33
    [ 13.569750] sd 0:0:0:0: [sda]
    [ 13.569753] Result: hostbyte=0x00 driverbyte=0x08
    [ 13.569755] sd 0:0:0:0: [sda]
    [ 13.569757] Sense Key : 0xb [current] [descriptor]
    [ 13.569761] Descriptor sense data with sense descriptors (in hex):
    [ 13.569763] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 13.569771] 5e 89 08 c0
    [ 13.569775] sd 0:0:0:0: [sda]
    [ 13.569777] ASC=0x47 ASCQ=0x0
    [ 13.569779] sd 0:0:0:0: [sda] CDB:
    [ 13.569781] cdb[0]=0x28: 28 00 5e 89 08 c0 00 00 08 00
    [ 13.569789] end_request: I/O error, dev sda, sector 1586038976
    [ 13.569933] ata1: EH complete
    [ 13.583315] ata1.00: exception Emask 0x0 SAct 0x7fffff9f SErr 0x0 action 0x6
    [ 13.583360] ata1.00: irq_stat 0x40000008
    [ 13.583399] ata1.00: failed command: READ FPDMA QUEUED
    [ 13.583441] ata1.00: cmd 60/08:38:30:08:89/00:00:63:00:00/40 tag 7 ncq 4096 in
    res 41/84:08:30:08:89/00:00:63:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 13.585478] ata1.00: status: { DRDY ERR }
    [ 13.585516] ata1.00: error: { ICRC ABRT }
    [ 13.585558] ata1: hard resetting link
    [ 14.069688] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 14.180020] ata1.00: configured for UDMA/33
    [ 14.180069] sd 0:0:0:0: [sda]
    [ 14.180072] Result: hostbyte=0x00 driverbyte=0x08
    [ 14.180074] sd 0:0:0:0: [sda]
    [ 14.180076] Sense Key : 0xb [current] [descriptor]
    [ 14.180079] Descriptor sense data with sense descriptors (in hex):
    [ 14.180081] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 14.180089] 63 89 08 30
    [ 14.180094] sd 0:0:0:0: [sda]
    [ 14.180095] ASC=0x47 ASCQ=0x0
    [ 14.180098] sd 0:0:0:0: [sda] CDB:
    [ 14.180099] cdb[0]=0x28: 28 00 63 89 08 30 00 00 08 00
    [ 14.180108] end_request: I/O error, dev sda, sector 1669924912
    [ 14.180245] ata1: EH complete
    [ 14.190091] ata1.00: exception Emask 0x0 SAct 0x7fffffe3 SErr 0x0 action 0x6
    [ 14.190153] ata1.00: irq_stat 0x40000008
    [ 14.190193] ata1.00: failed command: READ FPDMA QUEUED
    [ 14.190237] ata1.00: cmd 60/a8:28:70:08:89/00:00:63:00:00/40 tag 5 ncq 86016 in
    res 41/84:a8:80:08:89/00:00:63:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 14.190290] ata1.00: status: { DRDY ERR }
    [ 14.190328] ata1.00: error: { ICRC ABRT }
    [ 14.190371] ata1: hard resetting link
    [ 14.676439] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 14.779168] ata1.00: configured for UDMA/33
    [ 14.779214] sd 0:0:0:0: [sda]
    [ 14.779216] Result: hostbyte=0x00 driverbyte=0x08
    [ 14.779218] sd 0:0:0:0: [sda]
    [ 14.779220] Sense Key : 0xb [current] [descriptor]
    [ 14.779223] Descriptor sense data with sense descriptors (in hex):
    [ 14.779225] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 14.779233] 63 89 08 80
    [ 14.779237] sd 0:0:0:0: [sda]
    [ 14.779239] ASC=0x47 ASCQ=0x0
    [ 14.779241] sd 0:0:0:0: [sda] CDB:
    [ 14.779243] cdb[0]=0x28: 28 00 63 89 08 70 00 00 a8 00
    [ 14.779251] end_request: I/O error, dev sda, sector 1669924976
    [ 14.779391] ata1: EH complete
    [ 14.793467] ata1.00: exception Emask 0x0 SAct 0x3fffffe0 SErr 0x0 action 0x6
    [ 14.793513] ata1.00: irq_stat 0x40000008
    [ 14.793554] ata1.00: failed command: READ FPDMA QUEUED
    [ 14.793597] ata1.00: cmd 60/08:28:28:08:89/00:00:63:00:00/40 tag 5 ncq 4096 in
    res 41/84:08:28:08:89/00:00:63:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 14.793651] ata1.00: status: { DRDY ERR }
    [ 14.793690] ata1.00: error: { ICRC ABRT }
    [ 14.793733] ata1: hard resetting link
    [ 15.279789] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 15.378218] ata1.00: configured for UDMA/33
    [ 15.378240] sd 0:0:0:0: [sda]
    [ 15.378243] Result: hostbyte=0x00 driverbyte=0x08
    [ 15.378245] sd 0:0:0:0: [sda]
    [ 15.378247] Sense Key : 0xb [current] [descriptor]
    [ 15.378250] Descriptor sense data with sense descriptors (in hex):
    [ 15.378252] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 15.378260] 63 89 08 28
    [ 15.378264] sd 0:0:0:0: [sda]
    [ 15.378266] ASC=0x47 ASCQ=0x0
    [ 15.378268] sd 0:0:0:0: [sda] CDB:
    [ 15.378269] cdb[0]=0x28: 28 00 63 89 08 28 00 00 08 00
    [ 15.378277] end_request: I/O error, dev sda, sector 1669924904
    [ 15.378427] ata1: EH complete
    [ 15.390101] ata1.00: exception Emask 0x0 SAct 0x7fffff SErr 0x0 action 0x6
    [ 15.390148] ata1.00: irq_stat 0x40000008
    [ 15.390188] ata1.00: failed command: READ FPDMA QUEUED
    [ 15.390232] ata1.00: cmd 60/08:00:10:08:89/00:00:63:00:00/40 tag 0 ncq 4096 in
    res 41/84:08:10:08:89/00:00:63:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 15.390285] ata1.00: status: { DRDY ERR }
    [ 15.390324] ata1.00: error: { ICRC ABRT }
    [ 15.390366] ata1: hard resetting link
    [ 15.876541] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 15.977410] ata1.00: configured for UDMA/33
    [ 15.977500] ata1: EH complete
    [ 15.986870] ata1.00: exception Emask 0x0 SAct 0x7f807fff SErr 0x0 action 0x6
    [ 15.986916] ata1.00: irq_stat 0x40000008
    [ 15.986957] ata1.00: failed command: READ FPDMA QUEUED
    [ 15.987000] ata1.00: cmd 60/08:b8:20:08:89/00:00:63:00:00/40 tag 23 ncq 4096 in
    res 41/84:08:20:08:89/00:00:63:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 15.987054] ata1.00: status: { DRDY ERR }
    [ 15.987093] ata1.00: error: { ICRC ABRT }
    [ 15.987135] ata1: hard resetting link
    [ 16.473350] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 16.576437] ata1.00: configured for UDMA/33
    [ 16.576509] sd 0:0:0:0: [sda]
    [ 16.576511] Result: hostbyte=0x00 driverbyte=0x08
    [ 16.576514] sd 0:0:0:0: [sda]
    [ 16.576516] Sense Key : 0xb [current] [descriptor]
    [ 16.576519] Descriptor sense data with sense descriptors (in hex):
    [ 16.576520] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 16.576529] 63 89 08 20
    [ 16.576533] sd 0:0:0:0: [sda]
    [ 16.576534] ASC=0x47 ASCQ=0x0
    [ 16.576537] sd 0:0:0:0: [sda] CDB:
    [ 16.576538] cdb[0]=0x28: 28 00 63 89 08 20 00 00 08 00
    [ 16.576546] end_request: I/O error, dev sda, sector 1669924896
    [ 16.576642] ata1: EH complete
    [ 16.586801] ata1.00: exception Emask 0x0 SAct 0x7fff803f SErr 0x0 action 0x6
    [ 16.586847] ata1.00: irq_stat 0x40000008
    [ 16.586886] ata1.00: failed command: READ FPDMA QUEUED
    [ 16.586928] ata1.00: cmd 60/08:78:50:08:89/00:00:5e:00:00/40 tag 15 ncq 4096 in
    res 41/84:08:54:08:89/00:00:5e:00:00/00 Emask 0x410 (ATA bus error) <F>
    [ 16.586980] ata1.00: status: { DRDY ERR }
    [ 16.587018] ata1.00: error: { ICRC ABRT }
    [ 16.587058] ata1: hard resetting link
    [ 17.073307] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 17.175907] ata1.00: configured for UDMA/33
    [ 17.175963] sd 0:0:0:0: [sda]
    [ 17.175965] Result: hostbyte=0x00 driverbyte=0x08
    [ 17.175968] sd 0:0:0:0: [sda]
    [ 17.175970] Sense Key : 0xb [current] [descriptor]
    [ 17.175973] Descriptor sense data with sense descriptors (in hex):
    [ 17.175974] 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 17.175983] 5e 89 08 54
    [ 17.175987] sd

    I have only Arch installed, 64 bit, UEFI boot.
    The things got worse for me. Today I barely managed to boot the laptop. It was throwing a lot of errors at me:
    Sep 24 06:13:59 kernel: ata6.00: irq_stat 0x40000008
    Sep 24 06:13:59 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:13:59 kernel: ata6.00: cmd 60/a8:00:40:0e:00/00:00:00:00:00/40 tag 0 ncq 86016 in
    res 41/84:a8:87:0e:00/00:00:00:00:00/00 Emask 0x410 (ATA bus error) <F>
    Sep 24 06:13:59 kernel: ata6.00: status: { DRDY ERR }
    Sep 24 06:13:59 kernel: ata6.00: error: { ICRC ABRT }
    Sep 24 06:13:59 kernel: ata6: hard resetting link
    Sep 24 06:13:59 kernel: ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
    Sep 24 06:13:59 kernel: ata6.00: configured for UDMA/133
    Sep 24 06:13:59 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:13:59 kernel: Result: hostbyte=0x00 driverbyte=0x08
    Sep 24 06:13:59 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:13:59 kernel: Sense Key : 0xb [current] [descriptor]
    Sep 24 06:13:59 kernel: Descriptor sense data with sense descriptors (in hex):
    Sep 24 06:13:59 kernel: 72 0b 47 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    Sep 24 06:13:59 kernel: 00 00 0e 87
    Sep 24 06:13:59 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:13:59 kernel: ASC=0x47 ASCQ=0x0
    Sep 24 06:13:59 kernel: sd 5:0:0:0: [sda] CDB:
    Sep 24 06:13:59 kernel: cdb[0]=0x28: 28 00 00 00 0e 40 00 00 a8 00
    Sep 24 06:13:59 kernel: end_request: I/O error, dev sda, sector 3648
    Sep 24 06:13:59 kernel: ata6: EH complete
    Sep 24 06:14:30 kernel: ata6.00: exception Emask 0x1 SAct 0x7fffffff SErr 0x0 action 0x6 frozen
    Sep 24 06:14:30 kernel: ata6.00: irq_stat 0x40000008
    Sep 24 06:14:30 kernel: ata6.00: failed command: WRITE FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 61/08:00:00:08:24/00:00:41:00:00/40 tag 0 ncq 4096 out
    res 40/00:a8:87:0e:00/00:00:00:00:00/00 Emask 0x5 (timeout)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 60/a8:08:60:0f:00/00:00:00:00:00/40 tag 1 ncq 86016 in
    res 40/00:10:08:10:00/00:00:00:00:00/40 Emask 0x1 (device error)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 60/14:10:08:10:00/00:00:00:00:00/40 tag 2 ncq 10240 in
    res 40/00:10:08:10:00/00:00:00:00:00/40 Emask 0x1 (device error)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 60/01:18:24:0f:00/00:00:00:00:00/40 tag 3 ncq 512 in
    res 40/00:10:08:10:00/00:00:00:00:00/40 Emask 0x1 (device error)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 60/01:20:25:0f:00/00:00:00:00:00/40 tag 4 ncq 512 in
    res 40/00:10:08:10:00/00:00:00:00:00/40 Emask 0x1 (device error)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 60/01:28:26:0f:00/00:00:00:00:00/40 tag 5 ncq 512 in
    res 40/00:10:08:10:00/00:00:00:00:00/40 Emask 0x1 (device error)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6.00: failed command: READ FPDMA QUEUED
    Sep 24 06:14:30 kernel: ata6.00: cmd 60/01:30:27:0f:00/00:00:00:00:00/40 tag 6 ncq 512 in
    res 40/00:10:08:10:00/00:00:00:00:00/40 Emask 0x1 (device error)
    Sep 24 06:14:30 kernel: ata6.00: status: { DRDY }
    Sep 24 06:14:30 kernel: ata6: hard resetting link
    Sep 24 06:14:30 kernel: ata6: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
    Sep 24 06:14:30 kernel: ata6.00: configured for UDMA/133
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:14:30 kernel: Result: hostbyte=0x00 driverbyte=0x08
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:14:30 kernel: Sense Key : 0xb [current] [descriptor]
    Sep 24 06:14:30 kernel: Descriptor sense data with sense descriptors (in hex):
    Sep 24 06:14:30 kernel: 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    Sep 24 06:14:30 kernel: 00 00 10 08
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:14:30 kernel: ASC=0x0 ASCQ=0x0
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda] CDB:
    Sep 24 06:14:30 kernel: cdb[0]=0x28: 28 00 00 00 0f 60 00 00 a8 00
    Sep 24 06:14:30 kernel: end_request: I/O error, dev sda, sector 3936
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:14:30 kernel: Result: hostbyte=0x00 driverbyte=0x08
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda]
    Sep 24 06:14:30 kernel: Sense Key : 0xb [current] [descriptor]
    Sep 24 06:14:30 kernel: Descriptor sense data with sense descriptors (in hex):
    Sep 24 06:14:30 kernel: 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    Sep 24 06:14:30 kernel: 00 00 10 08
    Sep 24 06:14:30 kernel: sd 5:0:0:0: [sda]
    and so on... It somehow booted, but now journalctl says:
    ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
    184 End-to-End_Error 0x0032 099 099 099 Old_age Always FAILING_NOW 1
    while the Error hasn't occured yet.
    I think I wil take the emergency procedure, and start backing up my files and system ...
    I don't recall when this error first showed up, and I unluckily deleted my journal before noticing the problem, for it was getting big, so I can't trace back. But I have it in the journal since then (11.september). At begining only from time to time, but now things are getting worse.

  • [SOLVED] Arch Linux Duke (2007) Fails to Boot

    Folks, I have a unique and challenging problem that has exhausted my Arch Linux skills, and so I am now turning to you.
    I have a vintage Pentium Pro 200 system (that’s 200 MHz folks! – 200 MHz 686 architecture – the original 686!), two CPUs, running a dual boot between Windows NT 4.0 and Arch Linux Duke (2007). It has 512 MB of RAM and a 120 GB hard drive, partitioned up between Windows NT and Linux. I built this system new in 2007, hence the dated version of Arch.  It has run like a charm all these years, granted not getting that much use. After about a year of no use at all, I fired the system up last week to help with a little research for a blog post I was writing on networking Windows NT 4.0 and Mac OS 8.6. Windows NT 4.0 fired right up with no issue, and after I was done testing what needed to be tested I tried to boot over to Arch.
    After a year of disuse, Arch unexpectedly and stubbornly refused to boot. The boot process started up just fine, but towards the end, it declared that it could not mount the root file system on the root device and took a kernel panic and stopped. My Arch skills have gotten a bit rusty in the last few years, but I dusted them off and went to work. My guess was a file system or superblock error. Arch wouldn’t boot, but I dragged out my trusty RIPLinux 2.9 Rescue Live CD and fired it up. It came right up and ran, and I was able to mount the Arch partition and view all the files… everything seemed to be there; it just wouldn’t boot. Windows NT 4.0 AND RIPLinux both boot and run on the machine, so the hardware is fine as well.
    A little information on the disk layout. Windows NT 4.0 is in the first partition on the hard drive. The extended partition has a second Windows NT 4.0 partition (sort of a /home partition for Windows NT 4.0), followed by the main Arch partition (the one I am trying to boot), followed by a swap partition and then the largest partition, which I use to share data between Arch and Windows NT 4.0 (I have loaded an ext2/3 driver into Windows NT 4.0 and it happily accesses the Linux partitions on the box).
    RIPLinux’s e2fsck did find some issues with the Arch partition and I had it repair them all. I checked again afterwards that all the files were still there, and they were. With the partition now known to be clean, and the superblock repaired from one of the backups, all should have been well. However, Arch still wouldn’t (and still won’t) boot.
    RIPLinux has a kind of a chain loader function, so I had it attempt to start up Arch for me. However, this was flummoxed by the fact that Arch addresses all my hard drive partitions as /dev/sdax and RIPLinux addresses them as /dev/hdax. Hence, without a common language, it was hard to get the one to start the other. Still, using this function, I have been able to get a crippled version of Arch running on the machine again. No modules had been loaded, and so it couldn’t do almost anything, but there it was (and is), Arch Linux Duke, at the CLI level. From there, I can see all the files, I can move freely in and out of my user account and the root account, but I can’t make the thing actually boot properly.
    If you have read this far, you are a trooper.  Summarizing what I know, the hardware is good, the file system is clean, the superblock is good, I can mount it cleanly from a live CD and I can chain load a crippled version of Arch. Here is the boot process blow-by-blow. When I try to do a normal boot, the Windows NT 4.0 loader passes control to the Lilo boot sector I have placed on hda1 (sda1 in Duke’s parlance). Lilo takes over, present a menu and when I select Duke, takes off. Arch Linux Duke starts to boot. It gets a good long way along, all the way along to:
    :: Loading udev events                [Pass]
    :: Mount root Read-only
    :: Checking file systems
    This is where it stops.
    The next thing I see is:
    /dev/sda6
    The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else) then the superblock is corrupt and you might try running e2fsck with an alternate superblock:
        E2fsck –b 8193 <device>
    I then get a sort of character based splash screen that says
    **********FILE SYSTEM CHECK FAILED ****************************
    *   Please repair manually and reboot. Note that the root file system
    *   is currently mounted read-only. To remount it read-write, type:
    *   mount –n –o remount,rw /.  When you exit the maintenance
    *   shell, the system will reboot automatically
    Give root password for maintenance
    At this point, I give the root password and enter the maintenance shell as root. I typed in “mount” and the first entry I got back is
    /dev/sda6 on / type ext3 (rw)
    This is exactly the root partition that the start up complains about. It is clearly there.  I can see it, I can walk around it… it is clearly there. Why won’t it boot? Despite the message, the superblock is fine – it passes every test e2fsck can throw at it.
    At this point, I did a “e2fsck /dev/hda6 (which is how RIPLinux would have passed it into Arch” and it says it is “clean”. I suspect that the Superblock message is because Arch sees root as sda6, while RIP passed it in as hda6...
    Deciding to see what Arch would be seeing as it tried to set things up in the boot sequence, I tried the following next:
    # mknod “/dev/root2” b 3 6   
    (“3” because RIPLinux refers to my hard drive as IDE, while Arch refers to it by major number “8”, which is SCSI. By the way, it IS an IDE drive – not sure why Arch insists on using the sdx nomenclature instead of hdx)
    Then I entered “mount /dev/root2 /mnt/hda6” and “ls /mnt/hda6”
    All was well. I can make the node, I can mount it, and I can see the contents. All is clearly well, but something is clearly wrong enough that Arch can’t boot.
    I am totally out of ideas. I have tried every trick I know and am out of tricks. I would welcome any insights as to what I could try to get this venerable Arch installation back on its legs.
    By the way, the key section of the /etc/lilo.conf file (lest anyone want to know) is:
    image = /boot/vmlinuz26
       root = /dev/sda6
       label = ArchLinux-Duke
       initrd = /boot/kernel26.img
       read-only
    I am stumped. Thanks in advance for any and all pointers you may be able to offer.
    Last edited by mac57 (2014-06-02 17:42:21)

    Folks, thanks for all your helpful comments, and I wanted to report back to you that I finally overcame the issue, and ArchLinux-Duke (2007) is once again executing flawlessly on my old Pentium Pro 200 system. I won't bother reporting here all the blind allies I went down as I tried to figure out what was wrong, but in the end, literally moments before I was about to give up and overwrite my Arch installation with a new Linux variant (antiX seemed well suited for such old and low power hardware), my attention was drawn to a note I had made in my files back in 2007 about a problem with similar symptoms. In that case, I had just deleted ZenWalk Linux from the hard drive (both Arch and Zen had been on the drive), and merged several partitions to make use of the newly free space. This had changed Arch's view of the drive lettering, and what had been its /dev/sddx root device was now /dev/sdcx. Arch failed to boot, throwing off the same errors I was seeing now. I wish I had recalled that note a month or so ago! It would have saved me a lot of work and a lot of frustration.
    At any rate, as a last step, and testing the idea that maybe the drive lettering had changed for some reason, I repeatedly manually booted Arch, specifying root=/dev/sda6, then /dev/sdb6, then /dev/sdd6, and finally, /dev/sdc6. Eureka! Arch now considered itself to be on /dev/sdc6 whereas previously it had been on /dev/sda6. This got me part way there, but the boot failed at the filesystem check stage and threw me into root. I disabled the file system check in /etc/rc.sysinit and got farther. Then I cleaned up /etc/fstab to agree with the new sdc naming, and I was back on the air fully.
    So, what had happened was that Arch had changed its view of the drive it was on from sda6 to sdc6. While I could not understand why this "sudden" change had occurred, at least I had a solution, and had Arch back up and running.
    Trolling through the rest of my notes, I found the answer. In 2012, the Tekram SCSI card in the machine failed, and I ultimately replaced it with an Adaptec card. The Tekram card did not have a BIOS segment on it. The Adaptec card did. My guess is that this caused the two internal SCSI devices I have built into the system (Iomega ZIP and Jaz respectively) to be enumerated first, claiming the "sda" and "sdb". device names. That left "sdc" for the root device, and that is where Arch went next.  This is my guess anyway.
    I should have caught this issue back in 2012, at the time, but from my notes, I can see that I tested the new card thoroughly using the  Windows NT 4.0 side of the machine, but never thought to bring up Arch as well. Hence, this problem lay dormant for two years, before I attempted to fire up Arch last month and blundered right into it.
    It has not all been bad. I have learned more about the ext2 and ext3 file systems and superblocks in the intervening time than I will ever need to use. I have learned how to manually boot Linux on a machine whose BIOS is so old that it cannot address the disk cylinder that the kernel is on and I have completely refreshed the many general Linux skills that used to just flow from my finger tips. It has been a frustrating experience, but ultimately a successful and useful one.
    Just wanted to let everyone know that this is now [SOLVED]. I would mark the post as such, but I don't see any obvious way to do that. Thanks again everyone.

  • Mini Server OS 10.7.2 degrades, locks permissions, fails to boot

    New current model Mac Mini Server 5,3 i7 Quad with OS X Lion 10.7.2. Twin drives formatted HFS-journaled, everything stock. Using primarily as a personal and imaging computer using Adobe CS5 apps, not as a server. Originally attempted to set up twin drives as RAID 0, reformatting, but system was unstable and I reformatted drives back to stock HFS-journaled configuration, then did a clean OS install from recovery partition. System ran OK except would not allow me to move items to trash, save screen snapshots, etc. as I did not have privileges (?). Run Disk Utility from recovery partition and repair permissions. No help. Did "Get Info" and changed HD privileges to read & write, all enclosed items, for everyone. Got series of "Missing KEXT" hundreds. Reboot and reinstall system. Repeats behavior. Do a reformat and clean install. System runs fine for several hours, seems stable, so I install Java Runtime, then Adobe CS5, Spyder 3 Elite 4 calibration, ICC profiles, Epson printer and scanner, VueScan, all proven, Lion-friendly apps. System now requires permissions to move or save items, then I get "Missing KEXT" and OS will not reboot.
    Awaiting Apple service call where undoubtedly the tech will have me do another reformat and clean OS install over the course of several hours. Will tell me to disconnect everything and not use my apps. Will dick me around for another lost day and then get me further frustrated.
    I have been using Macs since 1989 and am ready to throw this one out. FWIW my 2007 Dual MBP is running Lion, installed from the USB stick, just fine, knock on wood. But I could spit nails over this stupid Mini Server and the bone-headed way this OS installs and breaks on what should be a very straight-forward set-up!
    How about it Apple, if the KEXT extensions are messed up, a fresh install should fix it. But it isn't. Even if there is some voodoo left, I pity the next poor user who gets trapped in this circle.

    Try booting into safe mode and see if the issues continue.
    http://support.apple.com/kb/HT1455
    this will disable all but a minimum of Apple components
    at boot time.  Therefor no attempt will be made to load
    any kexts that are not Apple.
    If booting is successful in this mode, it indicates that one
    of your third party products is starting something at boot
    time that is either calling or not providing a proper driver.
    If things boot without issue, then remove items from the
    StartupItems folder at the root /Library folder and also
    in your user preferences remove disable any startup items
    present there, then reboot normally.  If all is well, then put
    back startup items one at a time until the boot fails, then
    you have found the culprit.
    First need to get it to boot properly then can deal with
    other issues.
    As for the reliability of using the Mini Server as a workstation,
    At this point I have been using one for about 4 months now
    without issue.  I think you may have a 3rd party item that
    is causing an issue.  It is also possible that even though,
    as you claim, your apps are Lion freindly, they may have
    a corrupt file in their installers or a previously unknown bug.

  • Virtualbox winxpguest fails to boot second time

    I wanted to build a winxp sp2 vm on my arch acer revo, but I don't have a cdrom there.
    I have VirtualBox installed on another machine which does have a cdrom and have built a machine there. Both machines are running Arch Linux latest with
    kernel 3.12.1-1-ARCH #1 SMP PREEMPT Thu Nov 21 08:18:42 CET 2013 x86_64 GNU/Linux
    and the following vbox packages installed
    virtualbox 4.3.2-1
    virtualbox-ext-oracle 4.3.2-1
    virtualbox-guest-iso 4.3.2-1
    virtualbox-host-modules 4.3.2-4
    and the running user is in the vboxusers group.
    On the build machine everything runs fine for multiple boots etc etc.
    However, when I transfer the vm to the revo I find that winxp will boot just once. It doesn't seem to matter whether  I just rsync across or use virtualbox export/import.
    On the build machine I made sure that the VTx/AMD stuff is off (that option is not available on the revo), but clearly there's some residual issue.
    I see this in the VBox log for the failing case
    00:00:13.818617 Changing the VM state from 'POWERING_ON' to 'RUNNING'.
    00:00:13.835064 Guest Log: BIOS: VirtualBox 4.3.2
    00:00:13.836814 PIT: mode=2 count=0x10000 (65536) - 18.20 Hz (ch=0)
    00:00:13.886290 Guest Log: Keyboard error:31
    00:00:13.897960 ERROR [COM]: aRC=VBOX_E_IPRT_ERROR (0x80bb0005) aIID={480b372c-c0b5-4c23-9bd7-dcbb85b1594c} aComponent={Display} aText={Could not take a screenshot (VERR_NOT_SUPPORTED)}, preserve=false
    00:00:13.952796 ERROR [COM]: aRC=VBOX_E_IPRT_ERROR (0x80bb0005) aIID={480b372c-c0b5-4c23-9bd7-dcbb85b1594c} aComponent={Display} aText={Could not take a screenshot (VERR_NOT_SUPPORTED)}, preserve=false
    00:00:13.987106 2D video acceleration is disabled.
    00:00:14.968783 ERROR [COM]: aRC=VBOX_E_IPRT_ERROR (0x80bb0005) aIID={480b372c-c0b5-4c23-9bd7-dcbb85b1594c} aComponent={Display} aText={Could not take a screenshot (VERR_NOT_SUPPORTED)}, preserve=false
    00:00:15.968362 ERROR [COM]: aRC=VBOX_E_IPRT_ERROR
    Googling doesn't seem to reveal a suitable fix that works.
    Edit: I find that after a reboot of the host machine that the winxp guest will boot properly at least once, but after one or two reboots the guest again starts hanging.
    Edit: The VM is not the issue, nor its source. I built a new VM with an arch linux iso on the REVO and that too will only boot after a host restart.
    Last edited by replabrobin (2013-11-24 13:18:40)

    Thanks for your suggestions. Just to clarify what is happening and what I have done so far.
    Every time the Satellite C660 notebook is turned on when it has been sitting turned off for more than an hour it will not boot.
    Power on goes like this
    The Toshiba splash screen comes up
    The blinking cursor on the top left appears then disappears
    The screen goes blank (noticeably on still, but blank)
    No matter how long it is left it stays at this screen
    The above has happens so
    I press and hold the power button to turn it off
    Press to turn the notebook back on - one out of three times it states the system failed to start - offering boot to safe mode or turn on normally
    Pressing boot normally the computer will boot successfully
    The Satellite C660 will run perfectly with no errors, failures or crashes
    Reboot the Satellite C660 it will restart and boot correctly
    Turn the notebook off and leave it for an hour and it will not boot.
    I have scanned the original HDD and it has no errors or issues
    I have performed a full system reinstall using manufacturers HDD recovery.
    I have performed a full system reinstall from DVD recovery.
    I have performed a full system reinstall from DVD on to a brand new hard drive recovery.
    I have tested the brand new HDD no errors
    I have replaced the RAM memory
    There are no errors shown in system logs
    I have set the BIOS to defaults
    I have set the boot order to boot from HDD first
    I have not been able to update the BIOS as when the Toshiba update or manual download and attempt to update the BIOS fails.
    On a restart the computer boots as normal
    When booting for the first time of the day or if the computer is off for an hour or more it will not boot into Windows

  • MacBook Pro failing to boot up despite disk utility repair and PRAM

    Problem: MBP frozen on boot up screen with Apple logo and turning gear (which freezes after a while aswell)
    Solutions attempted: disk repair via custom recovery- disk utility, PRAM
    Device: MacBook Pro 15" (early 2010) running 10.9
    Additional info-
    Never had any issue with the device and this seems to have happened all of a sudden. Installed an SSD a few months ago, and just realised the ssd did not have a recovery partition. However I connected my older hardrive via USB to access recovery which seemed to work fine.
    NOTE: for the past few weeks, every now and then I was unable to power the device off and whenever this occurred, there seemed to be a few bugs (ie unable to empty thrash-error 50 and enable to increase/decrease volume/screen brightness). However, holding the power button and restarting it seemed to have fixed it.
    Had the same issue but this time around MBP failed to boot up.
    Any possible suggestions?

    Ranban wrote:
    Are you suggesting reinstalling the os?
    No.
    Furthermore, is there a way to keep the data intact using this method? Or retrieve it at the least?
    Repairing a disk should have no affect on the data, nor would an OSX installation.  However if the data has value, there always should be a backup, preferably two.
    In your original post you said "attempted: disk repair via custom recovery- disk utility".  The term 'custom recovery' to me is alien and thus confusing.
    What I am suggesting is a repair of the HDD using the original installation disk, not an OSX installation.
    You insert the disk holding down the C key at startup.  Proceed with the process until you see on the top of the display a menu bar.  Select UTILITIES and from the drop down menu select Disk Utility.  Then select Disk Utility>First Aid and then run Verify and repair.  Exit from the installation process.
    That way I know that the attempted repair was properly executed.  You may have in essence done that, but there is an element of doubt in my mind. 
    Ciao.

  • Will WebNS 7.5 auto fallback if new code failed to boot?

    Hi,
    I'm preparing for WebNs upgrade from 7.4 to 7.5 to 8.2
    And change will be done remotely.
    My question is, what will happen if the new code doesn't boot up after we reboot the CSS?
    Will it auto fall back to the previous working code?
    Thank you.

    Hello,
    Good to see your going to 8.20 software.
    I can't say for sure whether or not your CSS will fall back to the original image, although my suspicion is that it will not.  I will assume that your CSS is in a redundant configuration consisting of a pair of CSS.  Please correct me if I'm wrong.  You can alway upgrade the standby CSS, and make sure if boots up OK on the new code.  Then you can fail over to it, while you upgrade the second CSS.  This way, you would always be upgrading the standby CSS, so traffic should not be impacted, even in the event of a boot failure.  Then you can recover the standby that didn't boot properly while the master CSS is safely handling production traffic.
    Also, I would recommend using the upgrade script rather than the manual upgrade process, especially if you have any custom user accounts and/or custom scripted probes.  Another good idea as a backup plan is to temporarily (or permanently) arrange for console access to the two CSS during the upgrade process, just in case it is needed, as you are doing the upgrade remotely.
    Sean

  • LR2:  1st Launch of Demo - The application failed to initialize properly (0xc0150004)

    Hello all,
    I've never used Lightroom nor had any need to really justify buying it when PS meets my needs, but thought I'd at least take a look at Lightroom 2 to see what it's like. Well, upon installing the trial to my Vista 64 system, the subsequent launch of LR2 only gave the subject "application failed to initialize properly (0xC150004)" error. I see no posts regarding this particular error, and Google searches only turn up that this error could be due to a wealth of things, inclusive of the usual talk regarding viruses or spyware.
    Notwithstanding that I've got quite a number of applications installed, I keep my system relatively clean and do not suspect anything awry. Many speak ill of Norton products, of which I use Norton Internet Security 2008 and have had nothing negative to say about it...no issues from it with reagard to PS CS2 or CS3, so I'd expect none with LR2.
    Oh...and as far as any departure from the default installation goes, I installed LR2 to a separate partition where most of my applications get installed, rather than to the system partition. Of course, that should be transparent and not matter.
    I'm largely looking to see if there are any known obvious LR2 problems that might cause such an error to arise. If not, I'll just uninstall and forget about it. It's not worth spending too much time to resolve.
    I have installed LR2 under the Windows XP/SP2 boot configuration of my system, using a separate installation path on my programs partition than used for the 64-bit version, and all looks to be working fine there. So, this may be more of an LR2 issue with Vista 64.
    Thanks,
    Daryl

    Hi Ian,
    Thanks, but no luck with that idea either. I know 32- and 64-bit O/Ses are different, but I largely expected LR2 to work with both my installations under Norton Internet Security 2008 since all else does. A leap of assumption perhaps, but at least this exercise suggests the problem is unrelated to Norton software. I disabled all services and startup processes for both NIS2008 and Norton Ghost 14, via msconfig, even uninstalled and reinstalled LR2 under those conditions, and the problem persists.
    One additional thing I did observe, as I decided to monitor Task Manager while the LR2 installer ran, is that even after the installation completed and I left the box selected to launch LR2, the MS installer 'msiexec' did not close out. So, I rebooted and with no msiexece active in the list afterwards, again tried launching LR2 with no success.
    The only thing I can glean from this is a similar issue I had with Raxco PerfectDisk 2008, which launched 3 instances of msiexec during its installation, and never closed those. If I killed all related processes and attempted to launch PerfectDisk, it would freeze up at the splash screen with those 3 msiexec processes active again. I sent in some detailed notes to Raxco support for some feedback and if they come up with anything to offer that resolves the issue, perhaps it will be related to why the LR2 installer also doesn't close, or can't close, the msiexec. Perhaps a problem unique to my Vista 64 installation in spite of all else working. As with LR2, PerfectDisk works fine under XP32.
    Regards,
    Daryl

  • The application failed to initialize properly 0xc0000142.

    I installed Labview and TestStand 2012 SP1 on my computer. At the beginning it seemed everything was good, but after a couple of hours I tried to launch another application from TestStand and I got this message: The application failed to initialize properly 0xc0000142.
    Now each time that I want to launch TestStand the message come up.
    How can I fix this issue?
    My OS is Windows XP
    I uninstall and reinstall everything many times.

    Grey88 -
    1) What TestStand application are you running when you get this failure; sequence editor or a user interface?
    1a) If a LabVIEW user interface, what version of LabVIEW are you using?
    1b) If the sequence editor, does any portion of the UI show before the error occurs?
    1c) Do other applications from TestStand work OK?
    2) Just wanted to explicitly confirm that you rebooted the system after changing the ini file to test the issue?
    3) For the boot.ini change, does the problem still occur if you change the value to 2048 (2GB)? I suggest to try this because applications that are not Large Address Aware (LAA) in general should not be using more than 2GB of memory. The sequence editor does not support LAA until TestStand 2013 so the OS should restrict it from accessing > 2GB. On the other hand LabVIEW started enabling LAA on its executables in an earlier version.
    Scott Richardson
    National Instruments

  • [SOLVED] Custom Kernel failed to boot

    Hello everyone, this is my first time compiling my own kernel,  I was afraid of breaking the base system so I followed the guides on the wiki
    http://wiki.archlinux.org/index.php/Ker … n_with_ABS
    http://wiki.archlinux.org/index.php/Cus … n_with_ABS
    :: Running Hook [filesystems]
    :: Loading root filesystem module...
    ERROR: Failed to parse block device name for '/dev/sda4'
    ERROR: root fs cannot be detected. Try using the rootfstype= kernel paramter.
    ERROR: Unable to create/detect root device '/dev/sda4'
    I have tried to make an intrid by makeinitcpio -k <my kernel version> -g kernel-SLAB.img but that didn't really do anything.
    So I'm just wondering where I have done wrong, the kernel error messages are pertty cryptic so I have no idea, I would really appreciate any help I can get right now.
    Here's a list of the files that I have used or related to this problem. Thanks all!
    *PKGBUILD
    http://www.ualberta.ca/~blu2/kernel26/PKGBUILD
    *kernel config file
    http://www.ualberta.ca/~blu2/kernel26/config
    *GRUB menu.lst
    http://www.ualberta.ca/~blu2/kernel26/menu.lst
    *mkinitcpio conf
    http://www.ualberta.ca/~blu2/kernel26/mkinitcpio.conf
    *RC.conf
    http://www.ualberta.ca/~blu2/kernel26/rc.conf
    Update, HELP NEEDED
    To be on the safe side, I decided not to apply any EXTRA patch at all, so I used the kernel26 from /var/abs/core/base/kernel26, ONLY changing the package name and the features I wanted, (I changed the generic m686 MARCH to MK8 (amd semperon processor) and KEPT everything else as is to the .config file in /usr/src/linux-2.6.23.12-ARCH/.config
    The package compiled fine but again, but I can't boot properly, giving the same error as previous attempts. The mkinitcpio generated an image that I can boot with the original kernel that came with Arch, but not the kernel I compiled.
    I noticed that during boot, when loading udev, for the original kernel, there's a lot of messages showing modules being detected etc., but for my compiled kernel, there's only one message loading the PS2 keyboard, and nothing else, the HOOK filesystem was ran immediately after that. Is there anyway to capture those initial boot messages? Thanks!
    I'm not sure what I am doing wrong. Any help is appreciated.
    Update
    Kernel sucessfully compiled with the help of fwojciec, thank you.
    Last edited by blu3ness (2008-01-15 05:42:38)

    I can only really tell you how I do it -- I'm not exactly an expert with in-depth knowledge of how kernel works  
    The way I compile the kernel is by adapting the PKGBUILD for the current kernel from the ABS.  I use the script from this thread (http://bbs.archlinux.org/viewtopic.php?id=34815) to rename the kernel and add "make menuconfig" command to the PKGBUILD; I also manually add some patches.  If you want to use this script be careful: is a bit old and last time I've tried it changed "kernel26" to kernel26-[myname] in few some source addresses which obviously was not good but also not really difficult to fix. 
    When I compile the kernel like this I can just do "mkinitcpio -p kernel26-[myname]" and this generates the image without any problems.
    Sorry -- that's the best answer I can give you.  Perhaps somebody else will have ideas what needs to be done using your method to get the kernel to work.  Maybe just looking at the script will give you some ideas...

  • Dhcpcd-based network fails during boot

    Hi,
    My fully updated Arch_X86-64/KDE is connected to the Internet router via (on-board wired) eth1, and is configured to get an auto IP address.
    This has worked flawlessly for years till two days ago.
    Ever since,  eth1 service fails during boot, and requires several manual dhcpcd command to finally kick in. The same applies after waking from sleep mode. (see terminal output below)
    As can be seen the system is configured to load the (correct) r8169 mode.
    Please advise.
    Thanks
    Miki Badt
    ---------copy of respective commands---------------
    # journalctl -b | grep eth
    Sep 15 15:50:17 Miki_Arch systemd[1]: Expecting device sys-subsystem-net-devices-eth1.device...
    Sep 15 15:50:17 Miki_Arch systemd[1]: Expecting device sys-subsystem-net-devices-eth0.device...
    Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:05:00.0 eth0: RTL8168d/8111d at 0xffffc900119d2000, 6c:f0:49:ed:b3:e9, XID 083000c0 IRQ 49
    Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:05:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
    Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:06:00.0 eth1: RTL8168d/8111d at 0xffffc900119e6000, 6c:f0:49:ed:b3:eb, XID 083000c0 IRQ 50
    Sep 15 15:50:17 Miki_Arch kernel: r8169 0000:06:00.0 eth1: jumbo features [frames: 9200 bytes, tx checksumming: ko]
    Sep 15 15:50:23 Miki_Arch dhcpcd[339]: eth1: waiting for carrier
    Sep 15 15:50:23 Miki_Arch dhcpcd[336]: eth0: waiting for carrier
    Sep 15 15:50:29 Miki_Arch kernel: r8169 0000:06:00.0 eth1: link down
    Sep 15 15:50:29 Miki_Arch kernel: r8169 0000:06:00.0 eth1: link down
    Sep 15 15:50:29 Miki_Arch kernel: IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
    Sep 15 15:50:29 Miki_Arch kernel: r8169 0000:05:00.0 eth0: link down
    Sep 15 15:50:29 Miki_Arch kernel: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    Sep 15 15:50:53 Miki_Arch systemd[1]: [email protected]: control process exited, code=exited status=1
    Sep 15 15:50:53 Miki_Arch systemd[1]: Failed to start dhcpcd on eth0.
    Sep 15 15:50:53 Miki_Arch systemd[1]: Unit [email protected] entered failed state.
    Sep 15 15:50:53 Miki_Arch systemd[1]: [email protected]: control process exited, code=exited status=1
    Sep 15 15:50:53 Miki_Arch systemd[1]: Failed to start dhcpcd on eth1.
    Sep 15 15:50:53 Miki_Arch systemd[1]: Unit [email protected] entered failed state.
    #manual commands
    [root@Miki_Arch miki]# dhcpcd eth1
    dhcpcd[1039]: version 6.0.5 starting
    dhcpcd[1039]: eth1: waiting for carrier
    dhcpcd[1039]: timed out
    dhcpcd[1039]: exited
    [root@Miki_Arch miki]# ping www.ynet.co.il
    ping: unknown host www.ynet.co.il
    [root@Miki_Arch miki]# dhcpcd eth1
    dhcpcd[1046]: version 6.0.5 starting
    dhcpcd[1046]: eth1: soliciting an IPv6 router
    dhcpcd[1046]: eth1: rebinding lease of 192.168.1.13
    dhcpcd[1046]: eth1: leased 192.168.1.13 for 3600 seconds
    dhcpcd[1046]: eth1: adding host route to 192.168.1.13 via 127.0.0.1
    dhcpcd[1046]: eth1: adding route to 192.168.1.0/24
    dhcpcd[1046]: eth1: adding default route via 192.168.1.1
    lspci -v | grep Ethernet
    05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
    06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
    lspci -k
    05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
    Subsystem: Gigabyte Technology Co., Ltd Motherboard
    Kernel driver in use: r8169
    Kernel modules: r8169
    06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168 PCI Express Gigabit Ethernet controller (rev 03)
    Subsystem: Gigabyte Technology Co., Ltd Motherboard
    Kernel driver in use: r8169
    Kernel modules: r8169
    cat /etc/modules-load.d/realtek.conf
    r8169
    Last edited by mibadt (2013-09-15 13:29:25)

    Hi,
    I've some errors with the new dhcpcd, you should downgrade.
    https://wiki.archlinux.org/index.php/Do … g_Packages

  • MSI GT70 ONC-008US - Won't boot properly

    For whatever reason, my laptop refuses to boot properly now. For awhile it just had a problem booting from sleep (no image on screen, seemingly working otherwise), so I avoided doing that. It also did this when trying to power on the laptop, but this problem was fixed ignored by simply holding the button and trying again.
    It now it wont boot, despite the number of times I might try to make it. Nothing appears on the screen at all, sometimes my keyboard back-lights come on but now not even that happens. I don't know what to do. The hard drive (I think it's the hard drive?) makes a sort of clanking sounds a couple times and then goes quiet, occasionally making small beaps. USB devices power up per usual.
    If you know what might be happening I'd be eternally grateful. My only guess is that the hard drive is failing, but wouldn't the screen still show something if it was simply the hard drive failing?
    ##UPDATE:## After trying a million times it finally booted. I still want to figure out what is going on. Please help

    Quote from: tdesantiago on 07-April-13, 07:15:15
    I've contacted at least three computer repair shops in my local area and all seem to think it's the motherboard. FML
    It sucks. But it should still be under warranty from MSI. I would contact them to be perfectly honest.

  • G5 won't boot properly/running incredibly slow :(

    Hey, friends.
    So my mom and dad were kind enough to gift me their old G5 (I think they got it in 2006). Trouble is, I can't get it to boot properly. It takes about an hour for it to go from turning on to the point where the contents of the desktop appear and I would (theoretically) be able to do something. After just sitting there for the longest time with the color wheel spinning, the screen went blank although the computer and monitor were still on. Eventually it came back, but the computer runs incredibly slow. Like, clicking on the Apple menu caused the color wheel to spin for about ten minutes.
    I tried /sbin/fsck -fy, which is about the extent of my computer doctoring skills and this is the message I got:
    diskOs9: I/O error.
    Invalid node structure
    (4, 1771)
    ** Volume check failed.
    Any thoughts?
    Message was edited by: Alex_C.

    Pull the drive and put in a new one.
    I've never had much faith if any in Apple fsck or First Aid.
    The G5 stopped being sold in 2006 so that would make it one of the dual-core / pci express graphics.
    See if you have 10.4.6 or later DVD so you can attempt to repair and install while you wait to get Alsoft Disk Warrior, and a new system drive to work with and build a new boot drive etc to which you can copy over any files & programs you need.
    An emergency boot volume is pretty much a necessity with Mac. Your system drive directory structure is not going to make it. In theory a Safe Boot can deal with minor corruption and rebuild boot cache.
    There are some FAQs to guide you in your doctoring and sharpen your skills!

Maybe you are looking for

  • How many computers can I have my Creative Cloud on?

    Hello, I just have a question. Since I use my Adobe programs for school and business. I have a Macbook Pro and an iMac that I have the creative cloud synced too. Im getting another Macbook Pro and was wondering if Id be able to sync that laptop with

  • Custom Attribute not available in Available Fields section of Configuration

    Hi Experts, My requirement is to add a custom search field in contact search screen. For that i tried various options Option1 Added a model attribute in component/view  BP_CONT SEARCH/Search. The attribute got successfully added. But when i opened th

  • Windows 8 64bit Bootcamp 5 Drivers Install Fail

    2012 Retina MacBook Pro I installed Windows 7 64 Bit with bootcamp 4. I then upgraded to Windows 8 64 Bit Pro, using the microsoft installer for windows 8.I then tried to install Bootcamp 5, however the Bootcamp 5 installer states that I must have Wi

  • I can't watch videos on Nokia X2-01?

    Just now, I tried to watch a YouTube video on the phone but it say 'Subscribe to Packet Data First'. What does that mean? By the way, it usually works.

  • Delete the variants of a query from SAP GUI

    Hi all, We have migrated queries from 3.5 to 7.0, and now we are migrating their variants also. But while migrating variants we got a situation where some variants got copied but not activated in 7.0. so now we want to delete those variants and migra