Router Help Needed Badly!!!!!!!!!!

My nephew moved in to go to college and he needs to add his laptop to our wireless router. We have tried to have him set it up like I set up my laptop. It keeps telling him it is the incorrect password. I have even tried resetting to the default settings. Still nothing worked. Please, please help us. He is having to use a really weak network that has a lot of problems.

First of all you need to check the wireless settings (SSID and Security Key) of your Router.
Login to the Linksys Setup Page by typing 192.168.1.1 in the address bar...The default password is "admin" in the lower case.
Go to Wireless Tab and note down the SSID....Click on the subtab wireless security and note down your network key.
Now search for your network and connect it on the laptop.

Similar Messages

Wireless Router Help Needed! Please and Thank You

My warrenty has expired on my router, and Linksys is conveniently not able to help me get my router back on track. I have had the same problem several times, and have had the steps wrote down to fix it however, I have recently moved into a new place and conveniently lost the paper.
Usually it was a matter of just cloning my mac ID and it would work, in which I tired that with no success! Im frustrated and I need my internet for my schooling.
If anyone could help me it would be GREAT! Im not able to be on the internet to check so often as to if I have a reply on here, so if you feel you can help please call me!
Thanks in advance!
Stephanie
(Mod note: Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 05-21-2009 08:29 AM

First Connect the Modem to the Linksys Router on the Internet Port and then connect your Computer to the Linksys Router on the Port no.1.
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link

Urgent Help needed - BADI's in Infospoke

Hi,
My Scenario:
I am pulling data from master data using infospoke into Application server. I need some kind of easy transformations during this stage.
I got ZSTATE field in my data and I need to restrict my output to only certain states(Ex: NJ,CA, TX , MNetc). Since I can't give those selection conditions in infospoke I need to try BADI. I created a BADI and have target and source structure. Can anyone write me small code for this to eliminate other states and allow NJ , CA, MN, TX etc.
Source structure: /BIC/CYZZTEST
target Structure: /BIC/CZZZTEST
infospoke: ZZTEST
Field: Zstate
Class:ZCL_IM_ZZTEST
Method:IF_EX_OPENHUB_TRANSFORM~TRANSFORM
Full points to helpful answer!!
Anil.

The problem is cross user too - I have two user files on the machine and the same thing happens regardless of which user file I'm working in.
That points to s 'system-wide' issue.
Try resetting your SMC.
Resetting the System Management Controller >>
Also, you could try booting from your install DVD and see if it does it there. If it does not, it's more than likely a software issue and an Archive and Install should fix it.
Mac OS X: About the Archive and Install feature >>
-Bmer
Mac Owners Support Group - Join us @ MacOSG.com
  Mac611 Mobile Mac Support - about.Mac611.com
   iTunes:MacOSG Podcast | YouTube.MacOSG.com
                   An Apple User Group 
Have an iPhone or iPod touch? Enter Mac611.com in Safari on it for 'mobile Mac support.'

Setting up HP L-7590 via usb to wireless router, help needed..!

Hi,
I have been using my L7590 via lan to a wireless router for a few years... that was perfrect...
Recently I had to change router because of change of ISP. The new router is a Huawei B683... the problem I have is that this router does not allow LAN connections from the router ...!! It does has a USB port that is for the printer...
I am unsure as to how I setup the printer connected via usb to the router....
Do I use the network installation setup...? Or do I use the USB setup...??
Any help is greatly appreciated...
Thanks

Hi,
Connecting the printer to a router's USB port (aka. print server) will only allow you basic print functionality , it won't provide you any scan functionality, faxing from the computer, ink levels or any operation of the HP Solution Center program.
To get full functionality you must work with the provided functionality which means USB connection directly to a single PC or Ethernet connection to a router.. therefore using an Ethernet router will be the preferred solution for you.
In order to setup the printer as you described you should connect the printer to the USB port and go to Control Panel > System. click add a printer and add it through the network.. there might be a need to enter your wireless homepage to enable the printer through the USB, there might be additional setup information in there.. that veries between different print servers and you may contact Huawei support or your ISP for any assistant within the print server configuration.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Serious router help needed

hey all need some help here.
i got a msi rg54gs router hooked up with my ntl cable modem. In total there is two computers and a box connected to it via cables and a laptop via wireless.
i can access xbox live but cant join my friends games via my friend list. been told i need to open some ports so first question how i do that so it works. Secondly i may need to change the MTU how do i do that plz.
Anyone done this so it works with a xbox plz reply and help me. all help greatfully welcome thanx all

hey all need some help here.
i got a msi rg54gs router hooked up with my ntl cable modem. In total there is two computers and a box connected to it via cables and a laptop via wireless.
i can access xbox live but cant join my friends games via my friend list. been told i need to open some ports so first question how i do that so it works. Secondly i may need to change the MTU how do i do that plz.
Anyone done this so it works with a xbox plz reply and help me. all help greatfully welcome thanx all

Westell router - help needed

Hi, hope someone can help me with this westell router problem.
I have A90-750115 Vesalink router. My cable company set me with a static IP address. They told me to set my router to pull
static IP instead of dynamic IP from the modem. but the problem is I do nto know how to set the static IP on the router.
I checked online manual, but either I don't understand or it was not stated in the manual.
anyone knows how to set the static ip address on this router? or similar router in Vesalink line?
thanks

#1 I take it you have all of the settings, not just the Static IP.
Subnet Mask, Default Gateway and DNS Servers.
#2 If not, you need to get that first,
#3 I take it your cable modem is connected to the Uplink / E1 port of this Westell.
Source: http://www.westell.com/images/extranets/pdf/VersaLink_7500_User_Guide.pdf
on page 9 out of 186 pages.
#4 And I take it, you did not change the LAN IP of the Westell
#5 Go to 192.168.1.1 and log-in as need be to this Westell.
#6 If prompted to change the Default Password (page 32 to 34 out of 186 pages), do so.
#7 In the router go to Network Connections -> Versa Port.
#8 With Ethernet WAN Uplink Selected, change the connection type to Routed IP Address.
#9 Where it says, tunneling say disable.
#10 Then the next two option are:
a) Enable DHCP Client
OR to
b) Disable DHCP Client.
#11 Select Disable DHCP Client.
#12 Then enter in the Correct settings that you were given.
#13 Click on Apply
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

Help Needed Badly. Troubles with exporting video...

Hello, I created this account pretty much just for this problem, and I'm running under a very tight timeline so please if someone could give me an answer it would be very much appreciated. I have spent 8 hours over the past two nights as well as 4 hours today reworking, trying different things and combing the online community for any others experiencing these problems and/or solutions, so I am extremely stressed and tired if you could bare with me. So here it is:
I am editing and compiling a theatre production into a movie. I shot the show three times using a Canon HV30, imported the footage on a school computer (iMac, using iMovie '06), exported it in quicktime onto an external HD, brought it onto my computer (which, stupidly, has no firewire). The total file size was 7 hours of footage (85GB), and as a result my HD has about 300MB left on it, and has been excruciatingly slow. I have finished editing the movie, and I am now attempting to share it. All of the sources I have read tell me to share it in Media Browser, which will be accessible from iDVD. I attempted this many times, however I received multiple different error messages, only after watching it 'working' for 4 hours. Some have said that there was no virtual memory left (even after emptying the cache), some said that there wasn't enough HD space left, the exporting had encountered an error, error messages -50, -49, -48, and -47, and the most prominent one that I have been receiving told me that there had been a "parameter error" or something.
After researching online, I found that the '-50' error messages had to do with exporting to a MSDOS HD, which made sense because I was attempting to export to my iPod (formatted in Windows). My latest efforts have been trying to export it onto my HD, which is formatted for OSX, and has 350GB left on it. And yet, all of the problems persist (including error -50...?) any help would be greatly, greatly appreciated, as the DVD was due two days ago.
-Sean

+"Alright, so I moved over the footage and deleted it off the internal..."+
Did you move the Events using iMovie? If not, the project pointers become invalid, and you would get the error you did. While moving the event using iMovie, you don't need to "delete" anything!
Couple of options for you to recover from this.
A> (Slower) Move the Events back to the internal HD, and use iM to move the Event to the Ext HD.
B> (Faster, but convoluted) Create an alias for the specific Event folder (now on your ext HD/iMovie Events folder) under your local HD's iM Events folder. IM will now be able to "see" the files on the internal HD, even though they're stored on the Ext HD.
From the Help File: "To keep an item at its original location and put an alias for it in a new folder, hold down the Command and Option keys while you drag the item."
Sorry you're having to jump through hoops to get this working...

E1700 Advanced Routing - help needed

I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils

I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils

Eclipse error | Help needed badly

Hi,
My Eclipse was working properly a couple of days back but suddenly It's stopped working and gives me an error : "workspace does not contain a main type,Do you have a public void run method"
Now,I think the problem Is some how the jar's that I'm trying to upload aren't getting uploaded.
I say this because a strange problem has arised and I think this might have to do with Eclipse giving the above error.
This Is what I do to create a new java project
-Open eclipse
-save files to workspace
-click on new > java project
-Then,give the project a name and then click finish
-after that I create a new class by right clicking on the project folder > new > class >give the class a name and then click finish.
-after that I open workspace(thats on my desktop) click on the project folder make a new folder name It "lib" and upload the jar that I need for the project.
-after this I go back Into eclipse and right click on the project folder and hit refresh,now I see the folder"lib" containing the jar Inside It.
-I right click on the jar file and select "add to build path",and now theres the Issue comes In.
I want the jar to Into the reference librarys,because the last time I got the jar In the reference library It worked.
But this time I can't even manage to find where the reference library Is.
so when I click on add to build path the jar Instead of appearing in the reference library (which Isn't there) just dissapears.
I really need to fix this,because I cant test and write code until Its fixed.
heres a snapshot of how my eclipse framework looks : [http://www.flickr.com/photos/38561743@N03/4122304046/sizes/o/]
I tried to solve this on my own for hours and hours but It just Isn't working.
please guys help,I need to solve this.
Thanks,
Edited by: Parastar on Nov 21, 2009 7:26 AM
Edited by: Parastar on Nov 21, 2009 7:27 AM

Parastar wrote:
okay guys,I'v tried the eclipse forums for about 24 hours now.
but no response,those guys are really really slow.
please,some one here help me out.Quit begging. You've already been told this is not the place for this question. You're complaining about not getting an answer there, and begging people here to answer, as if that vindicates your decision to post here in the first place. But you haven't gotten your solution here either. Which is worse--no answer there, or a bunch of answers that don't help you here?

HELP NEEDED BADLY, creating Block Avoider game.

Could anyone please help me with creating a game called block avoider, i have a link here to show what the game should look like. I need alot of help with it so if anyone is good a coding and see`s this as an easy project helping me would be greatly appreciated.
LINK TO SIMILAR GAME:
http://scratch.mit.edu/projects/timo4932/82326

We can help, but we won't do it for you. Start the game, and post a question if you are stuck and need help.

Gereric extractor - help needed badly

Hi Geeks,
I am creating a generic extractor based on a database view for pricing conditions.
I am creating view on table KONP, A508. Also I need to include all the reference tables
needed for amount and quantity fields as well. (other wise causes error R8359 in RSO2)
I am in a strange situation where in for an amount KONP-KBETR (rate) reference table is
a structure RV13A-KONWA (rather than a database table).
In definition phase of view, system does not allow to include STRUCTURES (RV13A), It allows
only transparent database tables.
So I am stuck at a point where in I can not figure out how to pick the correct reference
table & field for KONP-KBETR. Or any work around is available.
Help is needed urgently.
Thanks in advance.
Monica

hi
After u create the view add it to the respective data source and when u save it a structure is generated and that structure can be appended via the append structures button on the top right ...u can append the field from the structure RV13A-KONWA and populated using Exits....
chk out to see if konwa can be used seems to be a possible solution...would make it less painful...if it works
Hope this is helpful
-A Geek

Tiger Help Needed Badly - won't start

Please can someone help.
My macbook has died!
I was restarting the computer because there was an update and the mac told me too. And then in the middle of restarting it froze. I tried everything (held down the start key, tried it with the option button held down too, reset the battery - the works) but all I get is a black screen. I went searching for my system disc to do the repair thing but I can't find it anywhere. What should I do?? I tried calling apple care but they said they don't sell tiger anymore.
Does anyone know where I could get one?? I bought leapord but I don't want to use it cos' I'm scared it will wipe all my files and give me no option to run a repair/ first aid on it.
Any suggestions are greatly welcomed.
Louisa

Hi Louisa, and Welcome to the Discussions!
Apple may supply an original System disc for a small fee, you'll need the Serial# of your Book.
Try this first...
http://docs.info.apple.com/article.html?artnum=106214

Help needed badly Insert text data from xml files into tables

Hi all, I have asked to do insertion of text from a xml file into tables upon receiving using pro*c. i've done quite an amount of research on xml parser in c but there wasn't much information for mi to use for implementation...
Guys don't mind helping me to clarify few doubts of mine...
1. Where can i get the oracle xml parser libs? Is it included when i installed oracle 8i?
2. Is there any tutorials or help files for xml parser libs where i can read up?
I need the xml parser to recognise the tags, followed by recognising the text after the tags.
eg. xml format
<studentID> 0012 </studentID>
<student> john </student>
<studentID> 0013 </studentID>
<student> mary </student>
text willl be inserted into tables like this:
studentID | student
0012 | john
0013 | mary
by the way i'm using oracle 8i on HP-UX. Thanks in advance.

I can answer one of of your questions at least
1. Where can i get the oracle xml parser libs? Is it included when i installed oracle 8i?You need the XML XDK. You can use http://www.oracle.com/technology/tech/xml/xdkhome.html as your starting point. I believe the 9i version works for 8i.
I have no pro*c experience so I can't offer any other suggestions regarding how to do this in pro*c.

Lynksys E900 Wireless-N300 Router - Help needed to share internet connection from PC to home network

Hi, I'm hoping someone can help me out with a problem I have:
I am currently connecting my PC to a mobile phone as a Wireless Access Point to give that PC access the internet. I also have a small home network, with one other PC and a Game Console. I own a Linksys E900 Wireless-N300 Router. My problem is this. How do I share that internet connection with the rest of the home network?
To the best of my knowledge its not possible to connect my mobile phone directly to my Linksys E900 Wireless-N300 Router, although if anyone has any ideas how to do this I'd love to hear!
So my alternative idea is to connect to the internet via one PC, set up that internet connection as "Shared." and then allow the other devices on the home network to connect thru this. My question is how do I set up my Linksys E900 Wireless-N300 Router to allow my other PC and game console connect to the internet? Bridge Mode? PPPoE? Any help or suggestions would be greatly appreciated! PS: both PC's are running on Windows 8

I have Cisco Linksys E900 router. I want to make my home Wi-Fi zone. But I don’t have Static IP. One more thing is that Service provider have web page Authentication. I have username and pass.
I am able to make SSID and security for my WI-FI LAN. I can use internet on one device. If I tried from second device again it’s asking me for username and password. While login it’s showing your first session in not logout. (Means I have to logout from 1st device and have to login on 2nd device.)
Is there any option that I can Use my all devices at same time?

ROUTER HELP NEEDED!

Me and my roommate both have laptops and we both want wireless internet. We bought the linksys WRT5G2. But it will only work if one of the computers is plugged into the router.. can someone please tell us how to make it work?

Hello,
I have a Dell Latitude laptop, with it came a ENPWI-S2 802.11g WIRELESS CardBus.
I have that pluged in and installed. The status on my computer is that im connected and have full signal strength, but still not connected to the internet. The Wireless router that I have is a Linksys Cisco WRT54G2 V1.5. I have no idea what to do I took it to a computer shop, and the internet worked there, but for some reason it wont work at my house. It's making me oh so very fustrated.
If anyone could help that would be great!!!
I would appreciate it alot.*

Router Help Needed Badly!!!!!!!!!!

Similar Messages

Maybe you are looking for