ROUTER HELP NEEDED!
Me and my roommate both have laptops and we both want wireless internet. We bought the linksys WRT5G2. But it will only work if one of the computers is plugged into the router.. can someone please tell us how to make it work?
Hello,
I have a Dell Latitude laptop, with it came a ENPWI-S2 802.11g WIRELESS CardBus.
I have that pluged in and installed. The status on my computer is that im connected and have full signal strength, but still not connected to the internet. The Wireless router that I have is a Linksys Cisco WRT54G2 V1.5. I have no idea what to do I took it to a computer shop, and the internet worked there, but for some reason it wont work at my house. It's making me oh so very fustrated.
If anyone could help that would be great!!!
I would appreciate it alot.*
Similar Messages
-
Wireless Router Help Needed! Please and Thank You
My warrenty has expired on my router, and Linksys is conveniently not able to help me get my router back on track. I have had the same problem several times, and have had the steps wrote down to fix it however, I have recently moved into a new place and conveniently lost the paper.
Usually it was a matter of just cloning my mac ID and it would work, in which I tired that with no success! Im frustrated and I need my internet for my schooling.
If anyone could help me it would be GREAT! Im not able to be on the internet to check so often as to if I have a reply on here, so if you feel you can help please call me!
Thanks in advance!
Stephanie
(Mod note: Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 05-21-2009 08:29 AMFirst Connect the Modem to the Linksys Router on the Internet Port and then connect your Computer to the Linksys Router on the Port no.1.
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link -
Router Help Needed Badly!!!!!!!!!!
My nephew moved in to go to college and he needs to add his laptop to our wireless router. We have tried to have him set it up like I set up my laptop. It keeps telling him it is the incorrect password. I have even tried resetting to the default settings. Still nothing worked. Please, please help us. He is having to use a really weak network that has a lot of problems.
First of all you need to check the wireless settings (SSID and Security Key) of your Router.
Login to the Linksys Setup Page by typing 192.168.1.1 in the address bar...The default password is "admin" in the lower case.
Go to Wireless Tab and note down the SSID....Click on the subtab wireless security and note down your network key.
Now search for your network and connect it on the laptop. -
Setting up HP L-7590 via usb to wireless router, help needed..!
Hi,
I have been using my L7590 via lan to a wireless router for a few years... that was perfrect...
Recently I had to change router because of change of ISP. The new router is a Huawei B683... the problem I have is that this router does not allow LAN connections from the router ...!! It does has a USB port that is for the printer...
I am unsure as to how I setup the printer connected via usb to the router....
Do I use the network installation setup...? Or do I use the USB setup...??
Any help is greatly appreciated...
ThanksHi,
Connecting the printer to a router's USB port (aka. print server) will only allow you basic print functionality , it won't provide you any scan functionality, faxing from the computer, ink levels or any operation of the HP Solution Center program.
To get full functionality you must work with the provided functionality which means USB connection directly to a single PC or Ethernet connection to a router.. therefore using an Ethernet router will be the preferred solution for you.
In order to setup the printer as you described you should connect the printer to the USB port and go to Control Panel > System. click add a printer and add it through the network.. there might be a need to enter your wireless homepage to enable the printer through the USB, there might be additional setup information in there.. that veries between different print servers and you may contact Huawei support or your ISP for any assistant within the print server configuration.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
hey all need some help here.
i got a msi rg54gs router hooked up with my ntl cable modem. In total there is two computers and a box connected to it via cables and a laptop via wireless.
i can access xbox live but cant join my friends games via my friend list. been told i need to open some ports so first question how i do that so it works. Secondly i may need to change the MTU how do i do that plz.
Anyone done this so it works with a xbox plz reply and help me. all help greatfully welcome thanx allhey all need some help here.
i got a msi rg54gs router hooked up with my ntl cable modem. In total there is two computers and a box connected to it via cables and a laptop via wireless.
i can access xbox live but cant join my friends games via my friend list. been told i need to open some ports so first question how i do that so it works. Secondly i may need to change the MTU how do i do that plz.
Anyone done this so it works with a xbox plz reply and help me. all help greatfully welcome thanx all -
Hi, hope someone can help me with this westell router problem.
I have A90-750115 Vesalink router. My cable company set me with a static IP address. They told me to set my router to pull
static IP instead of dynamic IP from the modem. but the problem is I do nto know how to set the static IP on the router.
I checked online manual, but either I don't understand or it was not stated in the manual.
anyone knows how to set the static ip address on this router? or similar router in Vesalink line?
thanks#1 I take it you have all of the settings, not just the Static IP.
Subnet Mask, Default Gateway and DNS Servers.
#2 If not, you need to get that first,
#3 I take it your cable modem is connected to the Uplink / E1 port of this Westell.
Source: http://www.westell.com/images/extranets/pdf/VersaLink_7500_User_Guide.pdf
on page 9 out of 186 pages.
#4 And I take it, you did not change the LAN IP of the Westell
#5 Go to 192.168.1.1 and log-in as need be to this Westell.
#6 If prompted to change the Default Password (page 32 to 34 out of 186 pages), do so.
#7 In the router go to Network Connections -> Versa Port.
#8 With Ethernet WAN Uplink Selected, change the connection type to Routed IP Address.
#9 Where it says, tunneling say disable.
#10 Then the next two option are:
a) Enable DHCP Client
OR to
b) Disable DHCP Client.
#11 Select Disable DHCP Client.
#12 Then enter in the Correct settings that you were given.
#13 Click on Apply
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button. -
E1700 Advanced Routing - help needed
I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils
I am having trouble creating static routes through my Linksys E1700 (Rev v1, f/w 1.0.02. I keep getting errors on all routes I try to enter. Either I get a complain that a part of an IP adress is not in range 1-233 or I get the error message "Invalid route" when trying to save the route. Can anyone post what restrictions are enforced on the entered static routes? What I want to achieve is access to a separate ADSL modem that the router is attached to. That means that I have assigned the modem an IP adress that is not on the local network and need the router to pass this adress through the WAN port, but not to the ISP gateway. Something along the lines of: Local address of router and IP range used by DHCP in the router: 192.168.0.0/24Local address of ADSL modem: 192.168.1.1/24 I want to route: 192.168.1.1/32 through WLAN interface with gateway 0.0.0.0 Any ideas why the router does not allow me to do this? Also, if I could get any type of route through the E1700 WLAN interface I could assign my modem to match that (as long as it is not an IP address I need to use :-) ) But I have not been able to set up any route to the WLAN interface with gateway 0.0.0.0. /Nils
-
Lynksys E900 Wireless-N300 Router - Help needed to share internet connection from PC to home network
Hi, I'm hoping someone can help me out with a problem I have:
I am currently connecting my PC to a mobile phone as a Wireless Access Point to give that PC access the internet. I also have a small home network, with one other PC and a Game Console. I own a Linksys E900 Wireless-N300 Router. My problem is this. How do I share that internet connection with the rest of the home network?
To the best of my knowledge its not possible to connect my mobile phone directly to my Linksys E900 Wireless-N300 Router, although if anyone has any ideas how to do this I'd love to hear!
So my alternative idea is to connect to the internet via one PC, set up that internet connection as "Shared." and then allow the other devices on the home network to connect thru this. My question is how do I set up my Linksys E900 Wireless-N300 Router to allow my other PC and game console connect to the internet? Bridge Mode? PPPoE? Any help or suggestions would be greatly appreciated! PS: both PC's are running on Windows 8I have Cisco Linksys E900 router. I want to make my home Wi-Fi zone. But I don’t have Static IP. One more thing is that Service provider have web page Authentication. I have username and pass.
I am able to make SSID and security for my WI-FI LAN. I can use internet on one device. If I tried from second device again it’s asking me for username and password. While login it’s showing your first session in not logout. (Means I have to logout from 1st device and have to login on 2nd device.)
Is there any option that I can Use my all devices at same time? -
Outboard effect routing help needed
I am trying to route the output of a track to a Korg Kaoss Pad and then have that outboard effect routed back into a new track. Using a pre-recorded audio track, how do I route that track out (I was using the headphone jack of the Mac as the out [i.e. line in of the Kaoss] and then routing the out of the Kaoss to the instrument 1 input on my Apogee Duet). I can't figure out how to assign the headphone output as the input of the new track. Sorry if this is too confusing.
Midlake wrote:
I need the output of a recorded track to go into the Kaoss and the output of the Kaoss to be the input of a new audio track. The original track will remain unprocessed and a new track will be that processed by he Kaoss.
So? Forgive me if I'm just misunderstanding you, but:
The INPUT is the physical socket that the sound is coming INTO the computer through.
The OUTPUT is the physical socket that the sound is going OUT OF the computer through.
If you're sending the dry signal out of the computer to the Kaoss pad through the headphone out, that headphone out is your OUTPUT.
If that signal is run through the Kaoss pad and from there into the computer through the Apogee's Input 1, then the Apogee Input 1 is the INPUT channel that you need to select on the new track in Logic.
Logic 9 will output and input to/from different devices at the same time, so you won't need to build an aggregate device. However, if you change the output device to the headphone out, no sound will come out of the Apogee's output (which I assume is hooked up to your monitors), so you won't actually hear what you're doing until you're done recording and switch the output back. -
(High Ip input) on My router , I need to troubleshoot why CPU is high !!!!
(High Ip input) on My router , I need to troubleshoot why CPU is high !!!!
=================
i have a cisco router 7200 NPEG2 processor , worked as LNS for PPPOVPDN circuits (Router for ADSL clients)
i have "high ip input on my processor" and there is alot of differnce on my router between operations done by cef and operations done by router cpu
as an example , lets make show cpu process sorted
CPU utilization for five seconds: 67%/54%; one minute: 67%; five minutes: 68%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 10837056 46891299 231 6.31% 6.04% 6.32% 0 IP Input
122 4081972 38214106 106 2.47% 2.36% 2.46% 0 L2X Data Daemon
270 467844 2089101 223 0.79% 0.78% 0.79% 0 PPP Events
275 1862224 2102444 885 0.71% 0.73% 0.71% 0 SNMP ENGINE
112 627104 93588 6700 0.39% 0.36% 0.37% 0 CEF: IPv4 proces
273 854004 4207368 202 0.31% 0.26% 0.24% 0 IP SNMP
52 453256 12321 36787 0.31% 0.31% 0.31% 0 Compute load avg
258 295540 701580 421 0.23% 0.17% 0.15% 0 RADIUS
142 45792 14107303 3 0.23% 0.21% 0.21% 0 HQF Shaper Backg
78 86532 166975 518 0.23% 0.17% 0.13% 0 ACCT Periodic Pr
260 483164 248673 1942 0.23% 0.19% 0.24% 0 L2TP mgmt daemon
272 63980 1073491 59 0.15% 0.16% 0.15% 0 IPHC Admin
77 111560 184597 604 0.15% 0.08% 0.06% 0 AAA ACCT Proc
261 330572 217566 1519 0.15% 0.12% 0.15% 0 L2TUN Applicatio
274 450584 2102164 214 0.15% 0.15% 0.15% 0 PDU DISPATCHER
16 152352 1081873 140 0.07% 0.08% 0.19% 0 EnvMon
279 229040 27298 8390 0.07% 0.10% 0.11% 0 VTEMPLATE Backgr
40 23704 53593 442 0.07% 0.03% 0.02% 0 Net Background
95 4512 55604 81 0.07% 0.00% 0.00% 0 PPP Hooks
109 6844 62029 110 0.07% 0.00% 0.00% 0 IP Background
269 21384 1931910 11 0.07% 0.06% 0.07% 0 PPP manager
271 116 60672 1 0.07% 0.00% 0.00% 0 Multilink PPP
23 98400 321 306542 0.00% 0.07% 0.03% 0 AAA high-capacit
=====================
as we see above , we have high "IP Input" about differnece in cpu =67-54=13 % , which is high value process in software .
i follwed the article here :
http://www.cisco.com/c/en/us/support/docs/routers/7500-series-routers/41160-highcpu-ip-input.html
i check and found that my router is fine ,
no arp calls.
no routing loops.
no flapping links.
i checked that my router has cef enabled and no enormous routing protocol updates
i found that i have big differnce between hardware & software process on the router which is 13 %
but when the traffic is more and more , the cpu reach reach 93 % and begin to have drops.
i just want to ask , how can i debug the operations that are done on the cpu processor of the router ???
i mean that if i know that traffic , i can estimate and know the problem that increasing my cpu !!!
another question :
how to debug the packest that has a ttl exceeded 50 or ttl exceeded 100 ?????
i dont wan tto make debug ip packed , because i have a huge traffic and it will let my router hanged due to large debug !!
===============
righ now i will post my router config and some verification:
drvirus#sh running-config
Building configuration...
Current configuration : 12291 bytes
upgrade fpd auto
version 12.4
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no service dhcp
hostname drvirus
boot-start-marker
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T7.bin
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T8.bin
boot-end-marker
logging message-counter syslog
aaa new-model
aaa group server radius radiusservers
server-private 10..f.f.f auth-port 1812 acct-port 1813 key 7 weifuhjkefkjdbhfjkasbfjka
aaa authentication login adminstaff local
aaa authentication login sdm_vpn_xauth_ml_1 group radius
aaa authentication login ahmad local
aaa authentication ppp vpdn group radiusservers local
aaa authentication ppp drvirus local
aaa authentication ppp vpdn1 local group radiusservers
aaa authentication ppp ddd none
aaa authentication ppp dddd none
aaa authentication ppp anyok none
aaa authorization network default group radius local
aaa authorization network vpdn group radiusservers local
aaa authorization network sdm_vpn_group_ml_1 local
aaa authorization network drvirus local
aaa authorization network vpdn1 local group radiusservers
aaa authorization network ddd none
aaa authorization network anyok none
aaa accounting delay-start
aaa accounting update newinfo periodic 10
aaa accounting network vpdn
action-type start-stop
broadcast
group radiusservers
aaa server radius dynamic-author
client xxxxxxxx
client 10.xxxxxx
client 10.xxxxxxxxx
server-key 7 dihcbsdjkbvcsdhmbvhsdbvsdhmbvsd
auth-type any
aaa session-id common
clock timezone GMT+3 3
no ip subnet-zero
no ip source-route
no ip gratuitous-arps
ip cef
no ip bootp server
ip domain name drvirus
ip name-server x.x.x.x.x
ip name-server 8.8.8.8
login block-for 180 attempts 3 within 60
login quiet-mode access-class telnet
login on-failure log
login on-success log
no ipv6 cef
ipv6 dhcp pool vvv
prefix-delegation pool version6
address prefix 3333::/64
dns-server 4444::1
multilink bundle-name authenticated
vpdn enable
vpdn logging
vpdn logging local
vpdn history failure table-size 50
vpdn-group eeeeeeeeeeee
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname qqqqqq
local name rrrrrrr
lcp renegotiation on-mismatch
l2tp tunnel password 7ekfhjjeklfnlenfl
l2tp tunnel timeout no-session 60
ip mtu adjust
username drvirus@!34`!512&$8#$232!^@^FGsdGD privilege 0 password 7 000sdkjhvsdkjvnah94313085g2355091407458E32425D
interface Loopback1
ip address ttttttt 255.255.255.255
interface GigabitEthernet0/1
description ttttttt
ip address 10.60.60.2 255.255.255.0 secondary
ip address 10.200.200.200 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/1.4
encapsulation dot1Q 4
ip address ttttttttt 255.255.255.224
interface GigabitEthernet0/1.14
encapsulation dot1Q 14
ip address 192.168.50.3 255.255.255.0
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
ip address 10.160.150.2 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/3
description rrrrrrr
ip address xxxxxxx 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex full
speed 1000
media-type sfp
negotiation auto
interface Virtual-Template1
ip unnumbered Loopback1
ip tcp adjust-mss 1412
no logging event link-status
peer default ip address pool xxxxx xxxxxx
ppp mtu adaptive
ppp authentication pap vpdn1
ppp authorization vpdn1
ppp accounting vpdn
router eigrp 2
redistribute connected metric 1 2 1 2 1
passive-interface default
no passive-interface GigabitEthernet0/1
network 10.200.200.200 0.0.0.0
no auto-summary
eigrp router-id 2.2.2.2
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.200.200.2
ip route dddddddddd 255.255.255.0 fffffff
ip route ddddddddd 255.255.255.0 ffffff
no ip http server
no ip http secure-server
ip radius source-interface GigabitEthernet0/2
radius-server attribute nas-port format d
radius-server configure-nas
radius-server host ddddddddddd auth-port 1812 acct-port 1813 key 7 dddddddddd
radius-server retransmit 0
radius-server key 7 dddddddddddddddddd
radius-server vsa send cisco-nas-port
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
drvirus#sh ip traffic
IP statistics:
Rcvd: 92454889 total, 5908020 local destination
0 format errors, 94 checksum errors, 3789577 bad hop count
0 unknown protocol, 23360 not a gateway
0 security failures, 0 bad options, 3730347 with options
Opts: 0 end, 0 nop, 0 basic security, 0 loose source route
0 timestamp, 0 extended security, 0 record route
0 stream ID, 0 strict source route, 3730347 alert, 0 cipso, 0 ump
0 other
Frags: 1409002 reassembled, 485 timeouts, 0 couldn't reassemble
4542214 fragmented, 9089659 fragments, 2659413 couldn't fragment
Bcast: 6024 received, 0 sent
Mcast: 56503 received, 31033 sent
Sent: 15839581 generated, 2407203241 forwarded
Drop: 23 encapsulation failed, 0 unresolved, 0 no adjacency
0 no route, 0 unicast RPF, 0 forced drop
0 options denied
Drop: 0 packets with source IP address zero
Drop: 0 packets with internal loop back IP address
0 physical broadcast
ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 4 unreachable
140579 echo, 33742 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 timestamp replies, 0 info request, 0 other
0 irdp solicitations, 0 irdp advertisements
0 time exceeded, 0 info replies
Sent: 0 redirects, 3530 unreachable, 33744 echo, 140579 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp, 0 timestamp replies
0 info reply, 46795 time exceeded, 0 parameter problem
0 irdp solicitations, 0 irdp advertisements
TCP statistics:
Rcvd: 19285 total, 0 checksum errors, 7 no port
Sent: 39402 total
BGP statistics:
Rcvd: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh, 0 unrecognized
Sent: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh
IP-EIGRP statistics:
Rcvd: 39154 total
Sent: 39275 total
PIMv2 statistics: Sent/Received
Total: 0/0, 0 checksum errors, 0 format errors
Registers: 0/0 (0 non-rp, 0 non-sm-group), Register Stops: 0/0, Hellos: 0/0
Join/Prunes: 0/0, Asserts: 0/0, grafts: 0/0
Bootstraps: 0/0, Candidate_RP_Advertisements: 0/0
Queue drops: 0
State-Refresh: 0/0
IGMP statistics: Sent/Received
Total: 0/0, Format errors: 0/0, Checksum errors: 0/0
Host Queries: 0/0, Host Reports: 0/0, Host Leaves: 0/0
DVMRP: 0/0, PIM: 0/0
Queue drops: 0
UDP statistics:
Rcvd: 5632168 total, 0 checksum errors, 9605 no port
Sent: 15536481 total, 0 forwarded broadcasts
OSPF statistics:
Rcvd: 0 total, 0 checksum errors
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
Sent: 0 total
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
ARP statistics:
Rcvd: 36012 requests, 25 replies, 0 reverse, 0 other
Sent: 3590 requests, 1883 replies (41 proxy), 0 reverse
Drop due to input queue full: 0
drvirus#sh interfaces switching
GigabitEthernet0/1 ffff
Throttle count 0
Drops RP 29334 SP 0
SPD Flushes Fast 183378 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 196591 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 50222652 1410586379 38933488 2377282438
Cache misses 0 - - -
Fast 2501299905 502401799 1732463443 1178236678
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 36178 2170680 3643 233084
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1039 385469 2067 772027
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 2266 138297 6179 370740
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
Interface FastEthernet0/2 is disabled
GigabitEthernet0/2
Throttle count 0
Drops RP 0 SP 0
SPD Flushes Fast 785 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 1900 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 382927 34296776 382540 106683985
Cache misses 0 - - -
Fast 198 31569 0 0
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1900 114000 1813 108780
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1030 378010 1031 378377
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
GigabitEthernet0/3 drvirus
Throttle count 0
Drops RP 15 SP 0
SPD Flushes Fast 22435 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 194236 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 40507058 2970006619 56462488 1872816742
Cache misses 0 - - -
Fast 1758170357 386468928 2449949282 3706868609
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 105 8085
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 5 300 7 420
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 1034 379478
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1644 105280 250040
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1644 105472 256356
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#
ANy help ??????!!!!!can some one determin if :
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
has a relation to my high cpu
her is agian my cpu process :
drvirus#sh processes cpu sorted
CPU utilization for five seconds: 69%/51%; one minute: 62%; five minutes: 59%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 22165548 147317354 150 7.60% 6.54% 5.74% 0 IP Input
16 682988 2637213 258 3.61% 0.70% 0.37% 0 EnvMon
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
270 484700 4987094 97 0.76% 0.84% 0.86% 0 PPP Events
260 746640 483367 1544 0.30% 0.51% 0.51% 0 L2TP mgmt daemon
112 1082540 228491 4737 0.30% 0.31% 0.31% 0 CEF: IPv4 proces
190 596 755 789 0.30% 0.02% 0.00% 2 SSH Process
279 461184 78909 5844 0.30% 0.39% 0.45% 0 VTEMPLATE Backgr
52 954592 29823 32008 0.30% 0.31% 0.31% 0 Compute load avg
272 53744 2782461 19 0.23% 0.17% 0.16% 0 IPHC Admin
261 513524 428266 1199 0.23% 0.38% 0.37% 0 L2TUN Applicatio
142 31888 35627222 0 0.23% 0.19% 0.20% 0 HQF Shaper Backg
258 570384 1602872 355 0.15% 0.18% 0.17% 0 RADIUS
78 43280 392561 110 0.15% 0.10% 0.08% 0 ACCT Periodic Pr
281 52340 385568 135 0.07% 0.08% 0.09% 0 IP-EIGRP: PDM
40 37300 138153 269 0.07% 0.09% 0.10% 0 Net Background
77 145860 443602 328 0.07% 0.06% 0.07% 0 AAA ACCT Proc
110 31060 53876 576 0.07% 0.03% 0.02% 0 IP RIB Update
45 11868 52400 226 0.07% 0.01% 0.00% 0 IF-MGR control p
115 20164 103667 194 0.07% 0.02% 0.00% 0 PPP IPCP
102 181600 489310 371 0.07% 0.14% 0.15% 0 SSM connection m
143 3148 1461382 2 0.07% 0.01% 0.00% 0 RBSCP Background
80 19488 22128 880 0.07% 0.02% 0.00% 0 CDP Protocol
23 189412 10771 17585 0.00% 0.15% 0.04% 0 AAA high-capacit
22 0 1 0 0.00% 0.00% 0.00% 0 CEF MIB API
21 0 2 0 0.00% 0.00% 0.00% 0 ATM Idle Timer
20 376 153594 2 0.00% 0.00% 0.00% 0 ARP Background
24 0 2 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
25 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager
26 1376 26590 51 0.00% 0.00% 0.00% 0 DDR Timers
31 4 30 133 0.00% 0.00% 0.00% 0 EEM ED Syslog
27 0 5 0 0.00% 0.00% 0.00% 0 Entity MIB API
33 324 147392 2 0.00% 0.00% 0.00% 0 GraphIt
34 0 2 0 0.00% 0.00% 0.00% 0 Dialer event
28 0 2 0 0.00% 0.00% 0.00% 0 Serial Backgroun
36 0 2 0 0.00% 0.00% 0.00% 0 XML Proxy Client -
Okay, I have a wrt54g v6 router that I use for 2 computers and an xbox (xbox live). Im getting an intermittent signal on all my devices and I have no clue as to why. All of my devices are connected via ethernet cable so I know its not wireless interference and i've changed everything I can think of that would cause this problem, firmware, MTU size, etc. I even created a static ip for my xbox. But the router is still getting degraded signals, the only thing I havent really done is uncheck all the boxes on my router firewall but to me that wouldn't do anything but allow more access to my already crappy network. If anyone has a solution or knows whats going on that would be so so helpful, thank you very much.
You might need to upgrade the firmware of the router as is normal for most WRT54G v6 routers.
Verify the router firmware version
1) click on start ---> run (type in cmd)
2) on the DOS Prompt (type in ipconfig)
► take note of the default gateway value
3) open up Internet Explorer and type in the default gateway value
4) username: leave it blank password: admin
5) go to the status tab: verify the firmware version
► if it's below 1.00.9 (i.e 1.00.0, 1.00.1, 1.00.4, 1.00.6, 1.00.7) then the router definitely needs an upgrade.
To upgrade the firmware:
1) download the firmware from www.linksys.com/downloads Look for your product model number from the list (i.e WRT54G v5)
2) save the file on your desktop
3) access the 192.168.1.1 page again
4) go to Administration - firmware upgrade
5) browse for the downloaded file and upgrade.
► Press the reset button of the router for 30 seconds and powercycle (i.e turn on and turn off the router).
► Reconfigure the router as per ISP settings. -
1941W configuration help needed
Our Deployment Scenario:-
1941W Gigabit Ethernet 0/0 is connected to the PPOE connection of the ISP.
Gigabit Ethernet 0/1 is connected to the wired LAN
I have created 2 wireless radio Cisco_Kamran_BGN which is operating at 2.4 Ghz Devices and Cisco_Kamran_A which is operating at 5Ghz Devices.
I have created 2 VLans for the Wireless.
Vlan 10 for Cisco_Kamran_A 192.168.10.x
Vlan 11 for Cisco _Kamran_BGN 192.168.11.X
The problem is the Wireless users are not getting the IP address from the respective DHCP server which has been configured on the Router.
Can please any from the community help me and show me where I am missing the configuration.
Please find my router & ap configuration below.
Router Configuration
Router#
sh run
Building configuration...
Current configuration : 3022 bytes
! No configuration change since last restart
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$TdQt$npYeaf/W0kRElcfMggzJ31
no aaa new-model
service-module wlan-ap 0 bootimage autonomous
no ipv6 cef
ip source-route
ip cef
ip dhcp excluded-address 192.168.1.1 192.168.1.50
ip dhcp excluded-address 192.168.10.1 192.168.10.10
ip dhcp excluded-address 192.168.11.1 192.168.11.10
ip dhcp pool DHCP
network 192.168.1.0 255.255.255.0
default-router 192.168.1.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_A
network 192.168.11.0 255.255.255.0
default-router 192.168.11.1
dns-server 195.229.241.222 213.42.20.20
ip dhcp pool Cisco_Kamran_BGN
network 192.168.10.0 255.255.255.0
default-router 192.168.10.1
dns-server 195.225.241.222 213.42.20.20
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO1941W-E/K9 sn FCZ1553C1VK
hw-module ism 0
redundancy
bridge irb
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered GigabitEthernet0/0
arp timeout 0
no mop enabled
no mop sysid
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 1
interface Wlan-GigabitEthernet0/0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
no ip address
interface Vlan10
ip address 192.168.10.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Vlan11
ip address 192.168.11.1 255.255.255.0
ip access-group DSL_ACCESSLIST in
ip nat inside
ip virtual-reassembly in
interface Dialer1
ip address negotiated
ip nat outside
ip virtual-reassembly in
encapsulation ppp
dialer pool 1
ppp authentication pap callin
ppp pap sent-username xxxxxx password 0 xxxxxx
ppp ipcp route default
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip access-list extended DSL_ACCESSLIST
permit ip 192.168.0.0 0.0.255.255 any
control-plane
line con 0
password xxxxxx
login
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 67
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
password xxxxxx
login
transport input all
scheduler allocate 20000 1000
end
Router#
Router#
Router#
Access Point Configuration
ap#
ap#
ap#
sh run
Building configuration...
Current configuration : 2603 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$JxdQ$a2/00bWJuhUKP9QLC94YD/
no aaa new-model
dot11 syslog
dot11 ssid Cisco_Kamran_A
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 1045081417161C5A555C7A7B
dot11 ssid Cisco_Kamran_BGN
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 020D05561907017015165949
username Cisco password 7 14341B180F0B
bridge irb
interface Dot11Radio0
description 802.11bgn radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
broadcast-key change 3600
ssid Cisco_Kamran_BGN
antenna gain 0
station-role root
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1
description 802.11a radio
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid Cisco_Kamran_A
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0
description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router
no ip address
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.10
description 802.11a bridge
encapsulation dot1Q 10
no ip route-cache
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
bridge-group 10 spanning-disabled
interface GigabitEthernet0.11
description 802.11bgn bridge
encapsulation dot1Q 11
no ip route-cache
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface BVI1
ip address dhcp client-id GigabitEthernet0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
no activation-character
line vty 0 4
login local
end
ap#
ap#
ap#Hi Stepehen,
Did the configuration as per your advice but i am getting the below mentioned error which i have highlighted it in red. Please advice what needs to be done.
Home
Re: 1941W configuration help needed
created by Stephen Rodriguez in Getting Started with Wireless - View the full discussion
conf t
interface Dot11Radio0
no ssid Cisco_Kamran_BGN
no encryption mode ciphers aes-ccm
exit
interface Dot11Radio1
no encryption mode ciphers aes-ccm
no ssid Cisco_Kamran_A
exit
dot11 ssid Cisco_Kamran_A
vlan 10
dot11 ssid Cisco_Kamran_BGN
vlan 11
exit
interface Dot11Radio0
encryption vlan 11 mode ciphers aes
ssid Cisco_Kamran_BGN
exit
interface dot11radio0.1
encapsulation dot1q 1 native
bridge-group 1
interface dot11radio 0.11
encapsulation dot1q 11
bridge-group 11
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
exit
interface Dot11Radio1
encryption vlan 10 mode ciphers aes-ccm
ssid Cisco_Kamran_A
interface dot11radio1.1
encapsulation dot1q 1 native
bridge-group 1
interface dot11radio1.10
encapuslation dot1q 10
bridge-group 10
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
end
wr
Reply to this message by going to Home
Start a new discussion in Getting Started with Wireless at Home -
How can you reset password on a NEW iPad that has not been connected to a PC? The one I used during setup is not working and I cannot get back into the iPad.
Once you reset the router, all of the customized settings of the router (network name, wireless security, etc.) will be erased and the router’s IP address will be reverted to 192.168.1.1, with a default password of “admin” and no username. If you want to restore the router’s original settings without reconfiguring, you have to save a backup file.
There are two methods that can be used in resetting the router:
1] Resetting the Router Using the Reset Button.
2] Resetting the Router Using the Web-Based Setup Page.
Here is the link for resetting the Linksys router - http://homecommunity.cisco.com/t5/Wireless-Routers/Help-needed-unable-to-reset-my-router-password/td... -
Troubleshooting help needed: My iMac keeps crashing and restarting with a notice: "Spinlock application timed out" What can I do?
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the page that opens.
Select the most recent panic log under System Diagnostic Reports. Post the contents — the text, please, not a screenshot. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header and body of the report, if it’s present (it may not be.) Please don't post shutdownStall, spin, or hang reports. -
help needed for writing query
i have the following tables(with data) as mentioned below
FK*-foregin key (SUBJECTS)
FK**-foregin key (COMBINATION)
1)SUBJECTS(table name)
SUB_ID(NUMBER) SUB_CODE(VARCHAR2) SUB_NAME (VARCHAR2)
2 02 Computer Science
3 03 Physics
4 04 Chemistry
5 05 Mathematics
7 07 Commerce
8 08 Computer Applications
9 09 Biology
2)COMBINATION
COMB_ID(NUMBER) COMB_NAME(VARCHAR2) SUB_ID1(NUMBER(FK*)) SUB_ID2(NUMBER(FK*)) SUB_ID3(NUMBER(FK*)) SUBJ_ID4(NUMBER(FK*))
383 S1 9 4 2 3
384 S2 4 2 5 3
---------I actually designed the ABOVE table also like this
3) a)COMBINATION
COMB_ID(NUMBER) COMB_NAME(VARCHAR2)
383 S1
384 S2
b)COMBINATION_DET
COMBDET_ID(NUMBER) COMB_ID(FK**) SUB_ID(FK*)
1 383 9
2 383 4
3 383 2
4 383 3
5 384 4
6 384 2
7 384 5
8 384 3
Business rule: a combination consists of a maximum of 4 subjects (must contain)
and the user is less relevant to a COMB_NAME(name of combinations) but user need
the subjects contained in combinations
i need the following output
COMB_ID COMB_NAME SUBJECT1 SUBJECT2 SUBJECT3 SUBJECT4
383 S1 Biology Chemistry Computer Science Physics
384 S2 Chemistry Computer Science Mathematics Physics
or even this is enough(what i actually needed)
COMB_ID subjects
383 Biology,Chemistry,Computer Science,Physics
384 Chemistry,Computer Science,Mathematics,Physics
you can use any of the COMBINATION table(either (2) or (3))
and i want to know
1)which design is good in this case
(i think SUB_ID1,SUB_ID2,SUB_ID3,SUB_ID4 is not a
good method to link with same table but if 4 subjects only(and must) comes
detail table is not neccessary )
now i am achieving the result by program-coding in C# after getting the rows from oracle
i am using oracle 9i (also ODP.NET)
i want to know how can i get the result in the stored procedure itsef.
2)how it could be designed in any other way.
any help/suggestion is welcome
thanks for your time --PradeeshWell I forgot the table-alias, here now with:
SELECT C.COMB_ID
, C.COMB_NAME
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID1) AS SUBJECT_NAME1
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID2) AS SUBJECT_NAME2
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID3) AS SUBJECT_NAME3
, (SELECT SUB_NAME
FROM SUBJECTS
WHERE SUB_ID = C.SUB_ID4) AS SUBJECT_NAME4
FROM COMBINATION C;
As you need exactly 4 subjects, the columns-solution is just fine I would say.
Maybe you are looking for
-
I'm in the process of adding lyrics to my music files (>26,000). Quite a few of my music files are instrumental only, and do not have any lyrics. I'd like to indicate the lyrics as "Instrumental," but don't want to have to press Option+I and manually
-
Request: song lyrics in Zen X-Fi 2
I would like to see support to song lyrics?
-
When i try to log into messages it tells me The server encountered an error processing registration
It tell me to try again later and when I do i get the same message. Please help!
-
Just for the record: I had received the error message "An error occurred while uploading one of your files. Please check your network connection and click Retry to resend your file" after all data apparently had been uploaded. After trying everything
-
How to search on creation Date to get specific date records
Hi, I have created a search page based on VO which contains creation Date field. Creation Date field stores date with time into database. af:query is created on this VO. Suppose I have created 10 records today and want to query that by providing toda