Router is not Clearing old Crypto Sessions
I am facing a stange problem on my router and its not clearing old state crypto sessions.
IPv4 Crypto ISAKMP SA
dst src state conn-id slot status
205.203.130.7 10.33.40.249 QM_IDLE 1025 0 ACTIVE
205.203.130.7 10.33.40.249 QM_IDLE 1021 0 ACTIVE
205.203.130.7 10.33.40.249 QM_IDLE 1017 0 ACTIVE
205.203.130.7 10.33.40.249 QM_IDLE 1013 0 ACTIVE
205.203.130.7 10.33.40.249 QM_IDLE 1009 0 ACTIVE
205.203.130.7 10.33.40.249 QM_IDLE 1005 0 ACTIVE
205.203.130.7 10.33.40.249 QM_IDLE 1001 0 ACTIVE
10.126.94.19 10.124.94.19 QM_IDLE 1079 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1027 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1023 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1019 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1015 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1011 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1007 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1003 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1099 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1097 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1095 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1093 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1091 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1089 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1087 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1085 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1083 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1081 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1078 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1076 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1074 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1072 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1070 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1068 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1066 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1064 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1062 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1060 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1058 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1056 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1054 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1052 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1050 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1048 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1046 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1044 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1042 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1040 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1038 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1036 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1034 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1032 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1030 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1028 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1026 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1024 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1022 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1020 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1018 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1016 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1014 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1012 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1010 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1008 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1006 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1004 0 ACTIVE
205.203.153.195 10.33.40.249 QM_IDLE 1002 0 ACTIVE
There has not been a problem like this for a while.
If you're running on older IOS version please upgrade to a MD release suitable for your router.
If you're already running something recent on this router - feel free to open a TAC case and have us investigate this thoroughly.
Similar Messages
-
Copied words into browser do not clear after closing session
When I go to a site that needs a password, I copy it from Last Pass into my browser. Then I enter my username and paste the password. Then when done, I sign off and close the page. I can go to another page that may want information. I fill it out and the previous password is still there and the only way I can get rid of it is to copy something new into the browser. Then, I have that new word stuck in my browsers. Whatever word is in there will only go away wen the computer is restarted. This can be just a password or any words that were copied and then pasted.
It used to be when I left a site that required a password, for example, when the page was closed, the word was gone instantly. I remember going back to a site that I need to do additional work on and when I clicked on the paste, it was greyed out or it would come up blank. That has how it has always worked until the last update. Have checked all security, cookie, privacy settings and it is all the same. Have tied every combination of settings and nothing will let the word or words clear out after I close Firefox. All browsing history ans history is cleared each time, but I have no control over the info copied into the browser, except to copy in something like 10 Xs, but then that stays. Have worked on this for a week and it really has me bugged. Last Pass told me it is a Firefox problem?My Last Pass usually fills in everything just fine and there is no need to copy anything, it automatically autofills. On one credit card site, It will not let me use autofill, so I enter my username, look up my 75 digit password and copy it and then paste it to the site. It used to be that when I left that site and had to comeback to it for some reason, the pasted password was gone. I just thought this was a security feature. If you are saying that the actions I have described or completely normal and safe, I will just quit worrying about it. Thanks.
-
Cisco UC560 Not Clearing Static Routes When VPN Connections Drop
We have a Cisco UC560 (UC560-FXO-K9) running "Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M),
Version 15.1(2)T2, RELEASE SOFTWARE (fc1)" The issue is when we have end users connecting with the Cisco VPN Client to this device sometimes we are unable to connect to any devices on our LAN or sometimes we can't connect to the LAN on the other end of our site-to-site VPN. The one symptom I've observed when this happens is that old VPN sessions that have disconnected appear to leave static routes from the user's outside IP at their home to an IP on our LAN to a Virtual-Access interface. When this starts to happen, I restart the firewall to clear out the stale static routes and the problem is fixed, for a while at least. Below is the current state where we have the site-to-site VPN connected to our branch office and 2 user's connected with Cisco VPN clients. Below that is the static route table which has 5 total Virtual-Access interface routes (one is an extra route for a user currently connected so that their outside IP is in the static route table with 2 inside IP's associated.) Is there a way to fix the cleanup of VPN connections when they terminate?
#sh crypto isakmp peers
Peer: <branch office outside IP> Port: 500 Local: <firewall's outside IP>
Phase1 id: <branch office outside IP>
Peer: <users's outside IP #1> Port: 50420 Local: <firewall's outside IP>
Phase1 id: EZVPN_GRP_437
Peer: <user's outside IP #2> Port: 49345 Local: <firewall's outside IP>
Phase1 id: EZVPN_GRP_437
Bugsy#sh ip ro st
Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
+ - replicated route, % - next hop override
Gateway of last resort is <next hop of ISP for firewall> to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via <next hop of ISP for firewall>
10.0.0.0/8 is variably subnetted, 12 subnets, 3 masks
S 10.0.0.153/32 [1/0] via <non-connected IP of VPN user>, Virtual-Access2
S 10.0.0.155/32 [1/0] via <non-connected IP of VPN user>, Virtual-Access2
S 10.0.0.156/32 [1/0] via <user's outside IP #2>, Virtual-Access3
S 10.0.0.158/32 [1/0] via <user's outside IP #1>, Virtual-Access3
S 10.0.0.159/32 [1/0] via <user's outside IP #2 again>, Virtual-Access2
S 10.1.10.1/32 is directly connected, Vlan90Hi Brian,
This sounds like you are running into the following known issue:
CSCtl03682 - EzVPN client: Several RRI routes pointing to same virtual interface
which is Dup'd to:
CSCtf39056 - RRI routes not deleted
This is fixed since 15.1(2)T4, so I would recommend upgrading to SWP 8.2 or higher. The only other way to clean up the stuck routes is to reload the router.
Thanks,
Brandon -
Yesterday We went to At and T store and they told me to download from old phone to new phone and I am really upset and I got Icloud and prove but part of still in 4S and has not go in 5S and that is biggest problem and no commuication that woman stay follow what she said but still not working so I do not know what else to do my do not understand and I would like to have someone do for us and AT and T store can not do that part so Told me Apple store and I called last night talk to some one on Apple store but told me that no go back to AT and T store so now total confuse and I am not get anywhere so and why they will not do it so therefore I do not think computer that not clear for us because we have no experince in computer program for this so both are deaf and not clear so over 50 years age and so we need face someone to do for us and told us do our self which is total upset us more so because my twins are in Orlando and can not call them because of problem contiunes in heart so I need someone who we can trust and help us. I do have IPAD mini and almost lost my calls to my twins and today I think get back but not 100 % so I am kind upset and who email us or I will have to go Apple Store and see if they know personal.
Open this support document http://support.apple.com/kb/HT2109 print it from the computer and follow the steps there. You need to backup your data from the first device and then restore that to the new device.
-
Time Macine not backing up.
As the harddrive is full, Can the time machine clear old backups, and override them with new backups. For example 5 - 6 days +++ old. Backups were proformed dayly
Any help much appreciated
Many thanks,If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting. -
Old Oracle Session with Tomcat is not kiiling automatically
Hi,
I am facing a problem of increasing inactive oracle sessions with tomcat, Old Oracle sessions with tomcat are visible with new one.
if somebaody did not restarted tomcat gracefully, then does Oracle keep the session connected or is there any way that whenever any one restarted tomcat abnormally, Oracle session can be killed.
I had restart the database to kill session.Could you please tell me that where do i set this parameter in parameter file or sql net file and what is the recommended value, do you have any document on this.
Another thing tomcat is in other server machine and my database is in different server machine, killing process in tomcat server machine manually may not kill linux process on oracle database machine and therefore oracle sessions are still there.
Is it possible?
Edited by: user605066 on 28-Aug-2008 04:59 -
CS4 - does not clear session info
I developed a small membership site for my club.
Everything works fine so far. I can log in and see the protected pages. I can log out and try and see the protected pages but I then get redirected to the page I specified for failed login.
This shows me that the login and logout function works.
The Problem
The problem is I logged in as me and I log out again. I then logged in as a different user and tried to update the different user's details. But when I went to the update form it still showed MY details in the update form and not those of the user who is currently logged in.
So it seems to me as if CS4 uses session variables to remember the login details but it was not cleared after the first users logged out.
Any suggestions on how to fix this?pietpetoors wrote:
The problem is I logged in as me and I log out again. I then logged in as a different user and tried to update the different user's details. But when I went to the update form it still showed MY details in the update form and not those of the user who is currently logged in.
So it seems to me as if CS4 uses session variables to remember the login details but it was not cleared after the first users logged out.
The code generated by the Dreamweaver Log Out User server behavior looks like this:
if ((isset($_GET['doLogout'])) &&($_GET['doLogout']=="true")){
//to fully log out a visitor we need to clear the session varialbles
$_SESSION['MM_Username'] = NULL;
$_SESSION['MM_UserGroup'] = NULL;
$_SESSION['PrevUrl'] = NULL;
unset($_SESSION['MM_Username']);
unset($_SESSION['MM_UserGroup']);
unset($_SESSION['PrevUrl']);
$logoutGoTo = "login.php";
if ($logoutGoTo) {
header("Location: $logoutGoTo");
exit;
As you can see, it's removing only the session variables created by Dreamweaver.
A more secure way of handling this would be to change the code to this:
if ((isset($_GET['doLogout'])) &&($_GET['doLogout']=="true")){
//to fully log out a visitor we need to clear the session varialbles
$_SESSION = array();
session_destroy();
$logoutGoTo = "login.php";
if ($logoutGoTo) {
header("Location: $logoutGoTo");
exit; -
3845 Router do not work with NME-X23ES-1GP Interface card
Need help!
I Trying install interface card NME-X 23ES-1GP on 3845 Router. I installed this card in slot 4, but router could not communicate with this card.
IOS version in Router 12.3
Here is results show diag command:
Slot 4:
Unknown (type 1187) Port adapter
Port adapter is disabled deactivated
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
Top Assy. Part Number : 800-25011-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : FOC090009VC
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : NME-X-23ES-1G-P
Version Identifier : V01
Base MAC Address : 0013.8088.9f80
MAC Address block size : 128
EEPROM format version 4
EEPROM contents (hex):
Possibly IOS release too old?Thank you for link. I read all information on this link. But I can't solve the problem.
Commands "show version" and "show flash:" show my the IOS image file version on Router (but not on interface modules). Here is Routers IOS image:
c3845-advipservicesk9-mz.123-11.T5.bin
I Can't connect to and open a session on the interface module. Command service-module interface slot/port session don't work.
What I should do next?
May is ncessarily upgrade Software on router?
Here is results show version and show flash:
BIG1#show flash:
-#- --length-- -----date/time------ path
1 29801400 Jun 28 2005 04:47:46 +00:00 c3845-advipservicesk9-mz.123-11.T5.bin
2 1651 Jun 28 2005 04:55:18 +00:00 sdmconfig-38xx.cfg
3 3085312 Jun 28 2005 04:55:40 +00:00 sdm.tar
4 763392 Jun 28 2005 04:55:56 +00:00 es.tar
5 820224 Jun 28 2005 04:56:10 +00:00 common.tar
6 1038 Jun 28 2005 04:56:24 +00:00 home.shtml
7 113152 Jun 28 2005 04:56:36 +00:00 home.tar
8 749101 Jun 28 2005 04:56:52 +00:00 256MB.sdf
9 1208320 Jun 28 2005 04:57:08 +00:00 ips.tar
27451392 bytes available (36560896 bytes used)
BIG1#show version
Cisco IOS Software, 3800 Software (C3845-ADVIPSERVICESK9-M), Version 12.3(11)T5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Sat 02-Apr-05 15:14 by yiyan
ROM: System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
BIG1 uptime is 57 minutes
System returned to ROM by reload at 07:11:45 UTC Tue Jul 12 2005
System image file is "flash:c3845-advipservicesk9-mz.123-11.T5.bin"
Cisco 3845 (revision 1.0) with 223232K/38912K bytes of memory.
Processor board ID FCZ0927714C
2 Gigabit Ethernet interfaces
1 Virtual Private Network (VPN) Module
4 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
479K bytes of NVRAM.
62720K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102 -
Firefox will not open old tabs
My computer crashed last evening and on restarting firefox, it goes to a new page without any of the old tabs available. Going under history has all of the options regarding restoring recently closed windows greyed out.
I did confirm that under preferences it is set to open previous tabs on starting firefox.
I have had the sessionstore.js file get corrupted previously. Looking in the profile folder showed the sessionstore.js to be a 1k file. So my first instinct was to just restore that file, and fortunately, there is a sessionstore.bak file with a time late last PM, so that file should still contain my last session.
I made a copy of the sessionstore.bak file and renamed it to sessionstore.js, but firefox still opens with a fresh session. I had the windows explorer (i.e. file manager) window open and as firefox was starting, the sessionstore.js got clobbered back to a 1k file suggesting the firefox is clearing the last session on opening. I tried restoring sessionstore.js from sessionstore.bak another time and making sessionstore.js read only, but firefox still will not revert back to the previous browsing session; instead it creates a new file called sessionstore.js.tmp.
I'm at a loss as to how to get my old browsing session back. I'm still using firefox V28.0. I haven't upgraded to V29 due to not wanting to lose the ability to export tabs as reported in the reviews of the android version of V29. Operating system is Win 7 SP1.If Firefox won't read the file when it's named sessionstore.js, it may have a structural problem. In that case, a little surgery might be needed, but it's hard to know what to suggest without more information.
Could try one of the data mining techniques in these posts to rescue the URLs from the sessionstore.js or sessionstore.bak file:
* Using Firefox's Browser Console (formerly known as Error Console): https://support.mozilla.org/questions/969046#answer-471950
* Using Firefox developer tool "Scratchpad": http://forums.mozillazine.org/viewtopic.php?f=38&t=622036&start=60&p=12098147#p12098147
* Using a third party website: https://firefox-session-restore.herokuapp.com/ -
Using Apex 4.1.1 on Oracle XE 11G (Linux)
I have a form and a report in and when you click on create button it will clear the cache in page 6 so you can create a new entry.
If click on the link on table which will set the value of P6_TID (type hidden) with a value, the typical Form & Report setup except I created it manually and was working fine for over a month since creation.
Now when I click on the CREATE button its no longer clearing cache in page 6. Instead it retrieves the latest values I had earlier (P6_TID holding the latest value).
However just earlier I was having another issue where I had to drop the parsing schema and got ORA-01940 - cannot drop a user that currently logged in, so I had to do a:
SQL> shutdown immediate;and as soon as Oracle stopped I started it up and created my user, granted necessary permissions and imported the old DMP file.
I've gone through this step many times but only now I am getting the ORA-01940 error. So have no idea if its anything to do with the issue of clearing cache I am having. Both issue coincided same time.
Has anyone had any such problem where they are unable to clear cache for a page or session? I got absolutely know idea what I have to do get it back working.
Cheers.Why would you shut down your database to kick a user. Just do
select * from v$sessionYou can find your schema that you want to drop with a where clause on the user column.
Now note the sid and the serial column and do
alter system kill session '#SID#, #SERIAL#';Replace #SID# and #SERIAL# with the values of your session you want to kill.
This will stop the ORA-01940 error.
Now for the APEX matter. The APEX session is completely different from the Database session.
If you submit values to the server then APEX keeps those values in session.
If you clear the cache of a page it really means that you clear the values of that page in the session.
Look in your session if those page items are cleared.
If they are not cleared there then watch out for a unwanted rowfetch of page processes. If you clear the page cache on create you most not give away any variables to that page hee! (espacially not a primary key)
Regards -
We have a number of old inter-company documents for the one of our plants sitting in the GR/IR that have not cleared via ERS. Please help me in finding the reason for not getting these cleared.
Sometimes GRIR does not happen because the material documents gets updated in table ZZEKRS.
The material number apperaing in this table are not picked up while running MRER
You need to run a program to clear the entries in this table(Program:ZZ_DELETE_ZZEKRS).
This is a correction program provided by SAP as part of *SAP Note 680459
This program should be svheduled before running the MRER job,so that it clears the entries before the MRER batch job.
Arvind -
Firefox will not open my previous session
Firefox 4 will not open any previous session once I shut down. I can have say 5 tabs open, close firefox, and reopen it and the session was saved. If I have those same 5 tabs open and shut down, then turn on my computer the next day, I can click on firefox, it will highlight the icon, and the highlight will disappear after about 5 seconds, and then I have to click it again, and it will open a totally new session. How do I fix this?
Make sure that you do not use [[Clear Recent History]] to clear the "Browsing History" if Firefox is closed.
-
CUBE IS NOT CLEARING THE DATA ON CONDITIONAL SCRIPT(ISSUE WITH NULLIFICATIO
Hi,
I am using AWM 10.2.0.2.0A and database is 10g Release 2 to build a cube.
Before the monthly incremental load I need to clear the old data.
For clearing(Nullifying) the cube I am using the new "Clear" command.
The Clear command has two options.
A) clear all the data without using any limits and
B) clear the current status. The option A is working perfectly fine. The issue
is when we need to clear only two months of data from the cube and I am using
Clear STATUS (option B )option.
After the execution data is not cleared (cube
is still showing the old data)
Please find below the program...............
(The cube is compressed and partitioned by year)
shw tod
aw attach olap_cview rw
limit ORA_PAX_AGT_PRT_MEASDIM to all
limit ORIGIN to all
limit DESTINATION to all
limit FAREBASIS to all
limit POS to all
limit DIS_NON to all
limit int_onl to all
limit airline to all
"lmt time to v_time
lmt time to '01/01/2005'
rpr time
"clear all from ORA_PAX_AGT_PRT_TOPVAR *** all data is deleted inspite of the
above limit
clear status from ORA_PAX_AGT_PRT_TOPVAR *** Nothing deletes
upd
cmm
dfn junk vrb integer
junk=1
upd
cmm
junk=2
upd
cmm
dlt junk
upd
cmm
shw tod
Any one can help me what I have to do to clear the cube.....................Hi Thanks for the input,
I have question.
I saw your program and my program whatever I submit in the discussion earlier.
I also using JUNK=1 keyword in my program . The only difference in your program and my program is
I am declare and assign JUNK=1 after the upd and commit ,In your program its immediately you are decalring and assing JUNK=1 after the clear status and two times JUNK=1 is assigned.
Please clarify me is this will make any difference to giving the JUNK=1 immediately after clear status and after clear status,up,command....??
In your program
================
clear status from ORA_PAX_AGT_PRT_TOPVAR *** Nothing deletes
dfn junk vrb integer *** need these lines (only second one if junk exists)
junk = 1 *** to work around clear/update bug.
upd
cmm
junk=1
upd
cmmjunk=2
upd
cmm
dlt junk
upd
cmm
shw tod
In My program
================
clear status from ORA_PAX_AGT_PRT_TOPVAR *** Nothing deletes
upd
cmm
dfn junk vrb integer
junk=1
upd
cmmjunk=2
upd
cmm
dlt junk
upd
cmm
shw tod
This is my query...This update will helpfull for me to before proceeding my test...
Thanks ,
Nat -
VF11 wrongly created with RV Doc type and with not clear status.
Hi All
Issue: There are 2 billing documents which were created(VF01) in March are canceled (VF11) in May. Cancel document is saved with a message (No automatic clearing of billing document XXXXXXXXX) and message diagnosis saying that u201CThe Automatic clearing of billing document and reversal is not possible. This may be, for example, because the line item update is deactivatedu201D
In the SD document flow cancel billing document is created and it's posted to accounting with Document type RV(which is not configured in the billing types) and it is in not clear status.
2 Sales order types are ZNRC(No Rebate u2013 Credit) second is ZCR (CM Req With Refer).
Order Type : ZNRC , Billing type :ZG2, Cancel billing type :Z5, Accounting document in billing type for ZG2: is DG and accounting document in cancel billing type Z5 is :(_) blank.
Order type: ZCR Billing type :G2, Cancel billing type :S2, Accounting document in billing type for G2: is DG and accounting document in cancel billing type S2 is :(_) blank.
FI document type Not maintained in the cancel billing type configuration because this should be determine by reversal document type DA which is maintained in DG document type from FI side. It will be triggered in VF11)
The above configuration is working with the order created VA01,billing VF01 and cancelling VF11 done in same period. If the order and billing done in old period and canceling(VF11) done in current period than FI document creating with RV document type and with not clear status in the document flow.
I reviewed similar issues with SAP Note and with below explanation:
"There are 2 procedures that are possible when Vf11 is posted.
Old Procedure - An FI "Reversal" document was created that was not connected with the orignal.
New Procedure - A Real FI reversal was carried out with clearing."
In this case, our system is following with new procedure except above mentioned orders created in previous period and and canceled in current period.
My Questions are: How the RV document is getting triggered here? why the cancel document (Reversal FI Doc) is not clearing?
Appreciate your answers or suggestions.
Thanks in advance,
Sunil
Edited by: Sunil kumar Matta on Jun 9, 2011 3:40 PMThank you Ivano.
I referred SAP note 1259505 and 339928. But initially we thought of none of the symptoms mentioned in the SAP note are matching with our issue. Then we contacted SAP online support and they suggested checking one SAP note (Mentioned above).
Our system is following new cancellation procedure, but itu2019s failing only for some few documents.
Finally we identified several reasons for the issue. One is profitability segment in the billing document and cancelled document is different due to some changes in segment assignments. Another one is consolidation- consolidation document does not exist in the billing document list but it is getting created in Canceled document (VF11).(Consolidation postings are switched off some time back and now itu2019s on)
After some discussions it is decided to include accounting document type (Reversal) in cancel billing types to avoid default RV document type in canceled billing document accounting document. And non-cleared documents need to be created manually in F-32.
Thread is closed.
Sunil -
How do I highlight text in the new Pages? It's not clear.
I have the new version of Pages. And it appears that highlighting of text is an issue. This is a basic function.
I found there is one quick key version, but doesn't clearly explain how to change highlighting colours. How to get into it.
I have to explain this to my 80 year old mom, who we told to get a Mac because it was easier!
So if anyone has it laid out step 1, 2, 3, that would be helpful, because it's not clear to me either.
Thanks!
Apple - please to a quick fix for this one, it should be the same as changing the size or the font or like bold or italic. Simple, clear, fast and doable..... for anyone!TO Peter,
Thanks for the list. I had found it in LibreOffice, tucked away in the Background tab of the Character pane opened by the Character... menu item in the Format menu, and named "Background Color. A few steps further down than in Pages. Apache OpenOffice has it in the same place. But both also have a hilight icon in the toolbar.
I didn't fin highlighting or Color fill in Text Edit (v1.8). Might need a further search.
But this well-equipped party of (one) oscurantist did find a shorter path to highlighting text in Pages '09, cleverly hidden in plain view! See the image below.
TO hscortez,
I'm aware that changing the text colour is not highlighting.
But YeOldMacFan pointed out how to change text colour AND how to change background colour of text, using Character fill, found in the Advanced Options (Pages 5) or the More (Pages '09) tab of the Text Inspector.
Character Fill fills the space around the character with the chosen colour. As shown above, it's essentially the same effect as dragging a hiliter pen along a line of printed text.
Unfortunately, whats shown above is the Character fill well on the format bar of Pages '09—right out in the open like the highlighter pen button in LibreOffice, and presumeably in MS Word. I don't have Pages 5 (avoiding it until a few more of the missing features arrive), but I do note that Pages for iOS offers highlight as one of the options in the contextual menu that appears when a block of text is selcted.
The process appears to be:
tap twice to select some text.
drag the handles at each end of the selection to adjust what's selected.
tap Highlight in the menu that has appeared on the screen.
One thing missing appears to be colour choice. The default is a 'hiliter yellow'. I didn't see a way to select a different colour.
"Hopefully, this will make it on their upgrade list. "
Hope is good, but taking action is useful.
Pages menu > Provide Pages Feedback > Make your request that this be added to Pages 5. Requests made through Provide ...Feedback go directly to Apple. Comments and questions here are read by users like yourself, and we don't have the ability to change the way the apps work. Not directly,anyway.
Regards,
Barry
Maybe you are looking for
-
How to find the physical path of a file
Usually, one can use absFileNmae() method to find the path of a file in Java. The problem is that it may only return a mapped path when a Servlet or JSP is running in a special server. For example, when I run a servlet "MyProgram" in JRun, absFileNam
-
Error in BPM: "no interface action for sender or receiver found"
hello, i configured a interface scenario SOAP - PI - Idoc using a BPM sync/async bridge. i followed the document when i try to call interface with my soap client i have the follow error in SXMB_MONI: Timeout condition of pipeline reached if i check t
-
Satellie Pro P100 - Overheating and too hot
Hi I have a Satellite Pro P100, PSPAEE, which is running way too hot, the keyboard and base get so hot that I have to stop using it as my hand hurts after getting too hot. This all started since I did loads of driver and BIOS updates, as I did them a
-
Hi everyone, I've written a custom program to read data from an input file and park an FI document (FBV1) using the standard load program (RFBIBL00) in "Call Transaction" data transfer mode. Before actually parking the document, we call RFBIBL00 wit
-
Delaying a message from being available on a Queue
I have the need to receive messages to a Queue I have set up and have it consumed several days later. The catch is that other messages will be coming in and will be consumed right away. I looked at the JMS message properties and I can't see anything