Router not routing!?

Hello
I've succesfully configured a tiny LAN of two Solaris 10 PCs. I've also tried to set up a router for ip-forwarding and NAT between the LAN and internet, according to many explanations on the net. However, my router doesn't seem to be forwarding packets from non-router: traceroute from non-router to internet shows packet stucking on the LAN's router interface. At the same time I can directly traceroute internet interface of the router from non-router. I'm connected to internet using DHCP by a cable modem, and connection works nice on the router machine. I enclose the files of the router understood important as well as some outputs of commands, so can anyone see what is wrong? Any help is highly appreciated!
/etc/nodename
Taavi
I have an empty /etc/dhcp.rtls0.
My /etc/hostname.rtls0 is empty, for DHCP to work correctly.
/etc/hostname.rtls1
taavetti
/etc/inet/hosts
127.0.0.1 localhost loghost
192.168.0.1 taavetti
192.168.0.2 Pohjoisneula
82.181.141.54 Taavi # Added by DHCP
/etc/inet/ipnodes
::1 localhost
127.0.0.1 localhost loghost
192.168.0.1 taavetti
192.168.0.2 Pohjoisneula
82.181.141.54 Taavi # Added by DHCP
I don't have /etc/defaultrouter, for DHCP to set the default router.
I don't have /etc/notrouter
/etc/inet/netmasks
192.168.0.0 255.255.255.0
/etc/ipf/ipnat.conf
map rtls0 192.168.0.0/24 -> 0/32 proxy port ftp ftp/tcp
map rtls0 192.168.0.0/24 -> 0/32 proxy port 7070 raudio/tcp
map rtls0 192.168.0.0/24 -> 0/32 portmap tcp/udp auto
map rtls0 192.168.0.0/24 -> 0/32
/etc/ipf/ipf.conf
pass in all
pass out all
/etc/ipf/pfil.ap
rtls -1 0 pfil
netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
192.168.0.0 192.168.0.1 U 1 0 rtls1
82.181.136.0 82.181.141.54 U 1 3 rtls0
224.0.0.0 82.181.141.54 U 1 0 rtls0
default 82.181.136.1 UG 1 41 rtls0
127.0.0.1 127.0.0.1 UH 4 111 lo0
routeadm
Configuration Current Current
Option Configuration System State
IPv4 forwarding enabled enabled
IPv4 routing enabled enabled
IPv6 forwarding disabled disabled
IPv6 routing disabled disabled

OK.
My current configuration is exactly what you see in my first message, but I try to clear it up a bit.
I have a router with two physical interfaces:
-rtls0 to ISP's DHCP via cable modem
-rtls1 to LAN: IP 192.168.0.1
/etc/dhcp.rtls0 exists to make DHCP configure
/etc/nodename contains my hostname Taavi
/etc/hostname.rtls0 is empty
/etc/hostname.rtls1 contains router's LAN hostname taavetti
/etc/notrouter doesn't exist
/etc/defaultrouter doesn't exist for DHCP to set the default route
/etc/inet/hosts
127.0.0.1 localhost loghost
192.168.0.1 taavetti
192.168.0.2 Pohjoisneula
82.181.141.54 Taavi # Added by DHCP
/etc/inet/ipnodes
::1 localhost
127.0.0.1 localhost loghost
192.168.0.1 taavetti
192.168.0.2 Pohjoisneula
82.181.141.54 Taavi # Added by DHCP
/etc/inet/netmasks
192.168.0.0 255.255.255.0
++++++++++
# netstat -rn
++++++++++
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface
192.168.0.0 192.168.0.1 U 1 0 rtls1
82.181.136.0 82.181.141.54 U 1 3 rtls0
224.0.0.0 82.181.141.54 U 1 0 rtls0
default 82.181.136.1 UG 1 41 rtls0
127.0.0.1 127.0.0.1 UH 4 111 lo0
++++++++++
# routeadm
++++++++++
Configuration Current Current
Option Configuration System State
IPv4 forwarding enabled enabled
IPv4 routing enabled enabled
IPv6 forwarding disabled disabled
IPv6 routing disabled disabled
THE PROBLEM: I can't contact internet, for example my nameserver, from a non-router which belongs to my LAN. Traceroute from there stucks on the router's LAN interface. Using or not NAT doesn't change the situation.

Similar Messages

Route not determing automatically at sales order level for some sales order

Dear All ,
Route not determing automatically at sales order level for some sales orders.We are using automatic route determination without wt group,eventhough we have configured the required settings
I have checked all the forums but didn't find any solution for the same.
Looking for your inputs .
Thanks inadvance
Regards
Venkat

Hi
1. Copare the Routes which are Automatically determined and which are not automatically determined
2. Have you mainted this route to be RELEVANT FOR TRANSPORTATION without this check route will not get picked up.
SPRO > Logistic General > Shipping > Basic Shipping Function > Routes > Define Routes > Define Routes and stages > Select the Route and check for it's settings > CHECK MARK Relevant for Transport. Without this check the route will not get picked up as of my understanding.
Thanks
RB

Linksys WRT54G Wireless-G Router Not working

I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.

I replaced my phone at apple y'day, due to a broken screen. Brand new phone, but i am unable to connect to wifi, at home or work, so presuming its a fault with the phone? not router, i have also done a software update, is there a solution? thanks

i replaced my phone at apple y'day, due to a broken screen. Brand new phone, but i am unable to connect to wifi, at home or work, so presuming its a fault with the phone? not router, i have also done a software update, is there a solution? thanks

Hi Eric,
What message do you get when you try to connect?
Cheers!

CALL DOES NOT ROUTE OUT THE LOCAL GATEWAY

Local calls will not route out the local Gateway of branch1 to the PSTN or from the PSTN back to branch1, however they will route out either CorpHQ or branch2 backup gateways. When I go into the route group configuration for branch1, and remove the backup gateways, I get a fast busy tone when I dial the local number. I know the MGCP Gateway at branch1 is functioning because when I dial 911 and run debug ISDN Q931, the call routes properly through branch1, so I have a call routing problem. I ran DNA and it came back as ROUTE THIS PATTERN and all of the number translations looked accurate, so I didn't have to check for any block patterns. I'm not getting any errors on the calling party phone display. When I deleted the route pattern for the branch1 site and forced it to use the global route pattern, I received a debug output on branch1. I do not know a debug command (such as debug voip dial-peer or debug ccsip messages) to use for an MGCP Gateway to see if the call is actually reaching the Gateway.
I have checked the following:
the route pattern configuration
the translation pattern configuration
the called party transformation pattern configuration
the route list configuration to make sure the correct route group for branch1 was selected
the route group configuration to make sure that the branch1 Gateway was first in the order of selected devices
the route pattern configuration to make sure the correct route list for branch1 ist selected
the Gateway configuration to make sure it's using the device pool for branch1 and to make sure the called party transformation CSS for the branch1 Gateway is applied
the device pool configuration to make sure it's using the route group branch1
Any assistance would be greatly appreciated
Regards,
Ron

Hi Nishant:
Please see the attachments for the Gateway pages
The significant digits for inbound calls for all 3 gateways is '4'
Please see the running-configs of the 3 gateways and the PSTN
Please see the debugs for the INBOUND calls
Many Thanks,
Ron
The following INBOUND call from the PSTN to 2065011001 is now working, however it is supposed to be routing through CorpHQ and is instead routing through Branch1. Please see 'DEBUG VOIP CCAPI INOUT' & 'DEBUG ISDN Q931'
Branch1#
ISDN Se0/0/0:23 Q931: RX <- DISCONNECT pd = 8 callref = 0x0096
        Cause i = 0x8290 - Normal call clearing
//22/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x16, digit_event=0x0, enable=FALSE, consume=FALSE)
//22/5A001212800B/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=22
//22/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x16, disp=0, digit_event=0x0, enable=FALSE, consume=FALSE)
//22/5A001212800B/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=22
//22/5A001212800B/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms))
//22/5A001212800B/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Null,
   Tone Direction=Network, Params=0x0, Call Id=22
//23/5A001212800B/CCAPI/ccGetCallStatistics:
   Call Stats=0x4A5346FC, Call Id=23
//22/5A001212800B/CCAPI/ccConferenceDestroy:
   Conference Id=0xC, Tag=0x0
//22/xxxxxxxxxxxx/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0xC, Source Interface=0x49E07FD4, Source Call Id=22,
   Destination Call Id=23, Disposition=0x0, Tag=0x0
//23/xxxxxxxxxxxx/CCAPI/cc_api_bridge_drop_done:
   Conference Id=0xC, Source Interface=0x495BABA4, Source Call Id=23,
   Destination Call Id=22, Disposition=0x0, Tag=0x0
//22/5A001212800B/CCAPI/cc_generic_bridge_done:
   Conference Id=0xC, Source Interface=0x495BABA4, Source Call Id=23,
   Destination Call Id=22, Disposition=0x0, Tag=0x0
//22/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//22/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
//22/5A001212800B/CCAPI/cc_api_get_transfer_info:
   Transfer Number Is Null
//23/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//23/5A001212800B/CCAPI/ccCallDisconnect:
   Cause Value=16, Call Entry(Responsed=TRUE, Cause Value=16)
//23/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x495BABA4, Tag=0x0, Call Id=23,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
//23/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 4821DDE8
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 1
//22/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x49E07FD4, Tag=0x0, Call Id=22,
   Call Entry(Disconnect Cause=16, Voice Class Cause Code=0, Retry Count=0)
//22/5A001212800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 4821DEC8
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 0
ISDN Se0/0/0:23 Q931: TX -> RELEASE pd = 8 callref = 0x8096
ISDN Se0/0/0:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x0096
ISDN Se0/0/0:23 Q931: RX <- SETUP pd = 8 callref = 0x0097
        Bearer Capability i = 0x8090A2
                Standard = CCITT
                Transfer Capability = Speech
                Transfer Mode = Circuit
                Transfer Rate = 64 kbit/s
        Channel ID i = 0xA18381
                Preferred, Channel 1
        Progress Ind i = 0x8183 - Origination address is non-ISDN
        Display i = 'Seattle US Phone'
        Calling Party Number i = 0x4180, '2065015111'
                Plan:ISDN, Type:Subscriber(local)
        Called Party Number i = 0xC1, '2065011001'
                Plan:ISDN, Type:Subscriber(local)
//-1/xxxxxxxxxxxx/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x49E07FD4, Interface Type=6, Destination=, Mode=0x9,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=, FinalDestinationFlag=FALSE, Outgoing Dial-peer=0, Call Count On=FALSE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=D000000002f5368f000000F580000097)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 1
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1210179280,feature_id:24
//24/74820328800C/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=6, FlowMode=1
//24/74820328800C/CCAPI/ccCallSetContext:
   Context=0x4A524790
//-1/xxxxxxxxxxxx/CCAPI/ccIFCallSetupRequestPrivate:
   Interface=0x495BABA4, Interface Type=9, Destination=0.0.0.0, Mode=0x9,
   Call Params(Calling Number=,(Calling Name=)(TON=Unknown, NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
   Called Number=(TON=Unknown, NPI=Unknown), Calling Translated=FALSE,
   Subscriber Type Str=, FinalDestinationFlag=FALSE, Outgoing Dial-peer=0, Call Count On=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, tg_label_flag=0, Application Call Id=D000000002f5368f000000F580000097)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 2
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1210179056,feature_id:25
//25/74820328800C/CCAPI/ccIFCallSetupRequestPrivate:
   SPI Call Setup Request Is Success; Interface Type=9, FlowMode=1
//25/74820328800C/CCAPI/ccCallSetContext:
   Context=0x4A524580
//25/74820328800C/CCAPI/cc_api_call_connected:
   Interface=0x495BABA4, Data Bitmask=0x0, Progress Indication=NULL(0),
   Connection Handle=0
//25/74820328800C/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
//24/74820328800C/CCAPI/cc_api_call_proceeding:
   Interface=0x49E07FD4, Progress Indication=NULL(0)
//24/74820328800C/CCAPI/cc_api_call_connected:
   Interface=0x49E07FD4, Data Bitmask=0x1, Progress Indication=DESTINATION IS NON ISDN(2),
   Connection Handle=0
//24/74820328800C/CCAPI/cc_api_call_connected:
   Call Entry(Connected=TRUE, Responsed=TRUE, Retry Count=0)
//24/74820328800C/CCAPI/ccCallModify:
   Nominator=0x1000, Params=0x4A2E7368, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x18, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x18, disp=0, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=15000(ms), Inter Digit Timeout=10000(ms))
//24/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID1=0x18, callID2=0x19, tag=0x0)
//24/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID1=0x18, gcid=0-0-0-0, tag=0x0)
//25/xxxxxxxxxxxx/CCAPI/ccConferenceCreate:
   (confID=0x4A2E757C, callID2=0x19, gcid=0-0-0-0, tag=0x0)
//24/74820328800C/CCAPI/ccConferenceCreate:
   Conference Id=0x4A2E757C, Call Id1=24, Call Id2=25, Tag=0x0
//24/xxxxxxxxxxxx/CCAPI/cc_api_bridge_done:
   Conference Id=0xD, Source Interface=0x49E07FD4, Source Call Id=24,
   Destination Call Id=25, Disposition=0x0, Tag=0xFFFFFFFF
//25/xxxxxxxxxxxx/CCAPI/cc_api_bridge_done:
   Conference Id=0xD, Source Interface=0x495BABA4, Source Call Id=25,
   Destination Call Id=24, Disposition=0x0, Tag=0x0
//24/74820328800C/CCAPI/cc_generic_bridge_done:
   Conference Id=0xD, Source Interface=0x495BABA4, Source Call Id=25,
   Destination Call Id=24, Disposition=0x0, Tag=0x0
//24/74820328800C/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0xD, Destination Call Id=25)
//25/74820328800C/CCAPI/ccConferenceCreate:
   Call Entry(Conference Id=0xD, Destination Call Id=24)
//24/74820328800C/CCAPI/cc_api_caps_ind:
   Destination Interface=0x495BABA4, Destination Call Id=25, Source Call Id=24,
   Caps(Codec=0x1, Fax Rate=0x1, Vad=0x1,
   Modem=0x2, Codec Bytes=20, Signal Type=3)
//24/74820328800C/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
//25/74820328800C/CCAPI/cc_api_caps_ind:
   Destination Interface=0x49E07FD4, Destination Call Id=24, Source Call Id=25,
   Caps(Codec=0x4, Fax Rate=0x2, Vad=0x1,
   Modem=0x0, Codec Bytes=20, Signal Type=2)
//25/74820328800C/CCAPI/cc_api_caps_ind:
   Caps(Playout Mode=1, Playout Initial=60(ms), Playout Min=40(ms),
   Playout Max=1000(ms), Fax Nom=300(ms))
//25/74820328800C/CCAPI/cc_api_caps_ack:
   Destination Interface=0x49E07FD4, Destination Call Id=24, Source Call Id=25,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=9314)
//24/74820328800C/CCAPI/cc_api_caps_ack:
   Destination Interface=0x495BABA4, Destination Call Id=25, Source Call Id=24,
   Caps(Codec=g729r8(0x4), Fax Rate=FAX_RATE_VOICE(0x2), Vad=OFF(0x1),
   Modem=OFF(0x0), Codec Bytes=20, Signal Type=2, Seq Num Start=9314)
//24/74820328800C/CCAPI/cc_api_call_modify_done:
   Result=0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_voice_mode_event:
   Call Id=24
//24/74820328800C/CCAPI/cc_api_voice_mode_event:
   Call Entry(Context=0x4A524790)
//24/74820328800C/CCAPI/cc_process_notify_bridge_done:
   Conference Id=0xD, Call Id1=24, Call Id2=25
//24/74820328800C/CCAPI/ccSetDigitTimeouts:
   Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms)
//24/74820328800C/CCAPI/ccSetDigitTimeouts:
   Call Entry(Inter Digit Timeout=4000(ms), Initial Digit Timeout=4000(ms))
//24/74820328800C/CCAPI/ccRestartDigitTimeoutMsec:
   Digit Timeout=0, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/ccCallReportDigits:
   (callID=0x18, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/ccCallReportDigits:
   Enabled=TRUE, Call Id=24
//24/xxxxxxxxxxxx/CCAPI/cc_api_call_report_digits_done:
   (vdbPtr=0x49E07FD4, callID=0x18, disp=0, digit_event=0x1, enable=TRUE, consume=FALSE)
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Enabled=TRUE, Disposition=0x0, Interface=0x49E07FD4, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_report_digits_done:
   Call Entry(Initial Digit Timeout=4000(ms), Inter Digit Timeout=4000(ms))
ISDN Se0/0/0:23 Q931: TX -> CALL_PROC pd = 8 callref = 0x8097
        Channel ID i = 0xA98381
                Exclusive, Channel 1
//24/74820328800C/CCAPI/ccCallModify:
   Nominator=0x1000, Params=0x4A2E6E68, Call Id=24
//24/74820328800C/CCAPI/cc_api_call_modify_done:
   Result=0, Interface=0x49E07FD4, Call Id=24
ISDN Se0/0/0:23 Q931: TX -> ALERTING pd = 8 callref = 0x8097
        Progress Ind i = 0x8088 - In-band info or appropriate now available
//24/74820328800C/CCAPI/ccGenerateToneInfo:
   Stop Tone On Digit=FALSE, Tone=Ring Back,
   Tone Direction=Network, Params=0x0, Call Id=24
//24/74820328800C/CCAPI/cc_handle_inter_digit_timer:
   Generate inter-digit timeout CC_EV_CALL_DIGIT_END event
The following INBOUND call from the PSTN to 5126022001 fails and is supposed to be routing through Branch1 and is instead routing through CorpHQ. Please see 'DEBUG VOIP CCAPI INOUT'
CorpHQ#
//-1/A31ADF52800B/CCAPI/cc_api_display_ie_subfields:
   cc_api_call_setup_ind_common:
   cisco-username=
   ----- ccCallInfo IE subfields -----
   cisco-ani=5126026222
   cisco-anitype=4
   cisco-aniplan=1
   cisco-anipi=0
   cisco-anisi=0
   dest=5126022001
   cisco-desttype=4
   cisco-destplan=1
   cisco-rdie=FFFFFFFF
   cisco-rdn=
   cisco-lastrdn=
   cisco-rdntype=-1
   cisco-rdnplan=-1
   cisco-rdnpi=-1
   cisco-rdnsi=-1
   cisco-redirectreason=-1   fwd_final_type =0
   final_redirectNumber =
   hunt_group_timeout =0
//-1/A31ADF52800B/CCAPI/cc_api_call_setup_ind_common:
   Interface=0x49F42894, Call Info(
   Calling Number=5126026222,(Calling Name=)(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed),
   Called Number=5126022001(TON=Subscriber, NPI=ISDN),
   Calling Translated=FALSE, Subscriber Type Str=RegularLine, FinalDestinationFlag=TRUE,
   Incoming Dial-peer=1, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), Calling IE Present=TRUE,
   Source Trkgrp Route Label=, Target Trkgrp Route Label=, CLID Transparent=FALSE), Call Id=-1
//-1/A31ADF52800B/CCAPI/ccCheckClipClir:
   In: Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed)
//-1/A31ADF52800B/CCAPI/ccCheckClipClir:
   Out: Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed)
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:cc_get_feature_vsa malloc success
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
cc_get_feature_vsa count is 1
//-1/xxxxxxxxxxxx/CCAPI/cc_get_feature_vsa:
:FEATURE_VSA attributes are: feature_name:0,feature_time:1241383960,feature_id:13
//13/A31ADF52800B/CCAPI/cc_api_call_setup_ind_common:
   Set Up Event Sent;
   Call Info(Calling Number=5126026222(TON=Subscriber, NPI=ISDN, Screening=Not Screened, Presentation=Allowed),
   Called Number=5126022001(TON=Subscriber, NPI=ISDN))
//13/A31ADF52800B/CCAPI/cc_process_call_setup_ind:
   Event=0x497D0010
//-1/xxxxxxxxxxxx/CCAPI/cc_setupind_match_search:
   Try with the demoted called number 5126022001
//13/A31ADF52800B/CCAPI/ccCallSetContext:
   Context=0x4A131A54
//13/A31ADF52800B/CCAPI/cc_process_call_setup_ind:
   >>>>CCAPI handed cid 13 with tag 1 to app "_ManagedAppProcess_Default"
//13/A31ADF52800B/CCAPI/ccCallProceeding:
   Progress Indication=NULL(0)
//13/A31ADF52800B/CCAPI/ccCallDisconnect:
   Cause Value=1, Tag=0x0, Call Entry(Previous Disconnect Cause=0, Disconnect Cause=0)
//13/A31ADF52800B/CCAPI/ccCallDisconnect:
   Cause Value=1, Call Entry(Responsed=TRUE, Cause Value=1)
//13/A31ADF52800B/CCAPI/cc_api_get_transfer_info:
   Transfer Number Is Null
//13/A31ADF52800B/CCAPI/cc_api_call_disconnect_done:
   Disposition=0, Interface=0x49F42894, Tag=0x0, Call Id=13,
   Call Entry(Disconnect Cause=1, Voice Class Cause Code=0, Retry Count=0)
//13/A31ADF52800B/CCAPI/cc_api_call_disconnect_done:
   Call Disconnect Event Sent
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
:cc_free_feature_vsa freeing 49FE0410
//-1/xxxxxxxxxxxx/CCAPI/cc_free_feature_vsa:
vsacount in free is 0
PSTN#sh run
Building configuration...
Current configuration : 13975 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname PSTN
boot-start-marker
boot-end-marker
card type e1 0 0
card type t1 0 1
logging message-counter syslog
no aaa new-model
clock timezone EST -5
clock summer-time EST recurring
network-clock-participate wic 0
network-clock-participate wic 1
no network-clock-participate aim 0
dot11 syslog
ip source-route
ip cef
no ip domain lookup
ip domain name att.com
ip name-server 177.1.100.110
ip multicast-routing
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
redirect ip2ip
fax protocol cisco
sip
bind control source-interface Loopback10
bind media source-interface Loopback10
header-passing
voice translation-rule 101
rule 1 /^\+.*/ //
rule 2 /^501.*/ //
rule 3 /^1206.*/ //
rule 4 /^00.*/ //
rule 5 /^0011.*/ //
rule 6 /^206/ /1206/
rule 7 /^1512.*/ /\0/
rule 8 /^011$.*$/ /\1/
voice translation-rule 102
rule 1 /^1$2065015111$$/ /\1/ type any subscriber plan any isdn
rule 2 /^1$2065015555$$/ /\1/ type any subscriber plan any isdn
rule 3 /^1$2065015151$$/ /\1/ type any subscriber plan any isdn
rule 4 /^1$5126026222$$/ /\1/ type any national plan any isdn
rule 5 /^31670357575$/ /&/ type any international plan any isdn
rule 6 /^31207037333$/ /&/ type any international plan any isdn
rule 7 /^31107047444$/ /&/ type any international plan any isdn
rule 8 /^911$/ /&/ type any unknown plan any unknown
rule 9 /^15126022.../ /&/ type any unknown plan any unknown
rule 10 /^31207033.../ /&/ type any unknown plan any unknown
rule 11 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 103
rule 1 /^206.*/ /&/ type any subscriber plan any isdn
rule 2 /^1/ // type any national plan any isdn
rule 3 /^00/ // type any international plan any isdn
voice translation-rule 201
rule 1 /^\+.*/ //
rule 2 /^602.*/ //
rule 3 /^1512.*/ //
rule 4 /^00.*/ //
rule 5 /^0011.*/ //
rule 6 /^512/ /1&/
rule 7 /^1206.*/ /&/
rule 8 /^011$31.*$/ /\1/
voice translation-rule 202
rule 1 /^1$5126026222$$/ /\1/ type any subscriber plan any isdn
rule 2 /^1$2065015555$$/ /\1/ type any national plan any isdn
rule 3 /^1$2065015151$$/ /\1/ type any national plan any isdn
rule 4 /^1$2065015111$$/ /\1/ type any national plan any isdn
rule 5 /^31670357575$/ /&/ type any international plan any isdn
rule 6 /^31207037333$/ /&/ type any international plan any isdn
rule 7 /^31107047444$/ /&/ type any international plan any isdn
rule 8 /^911$/ /&/ type any unknown plan any unknown
rule 9 /^12065011.../ /&/ type any unknown plan any unknown
rule 10 /^31207033.../ /&/ type any unknown plan any unknown
rule 11 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 203
rule 1 /^512.*/ /&/ type any subscriber plan any isdn
rule 2 /^1/ // type any national plan any isdn
rule 3 /^00/ // type any international plan any isdn
voice translation-rule 301
rule 1 /^\+.*/ //
rule 2 /^20.*/ //
rule 3 /^0$[1-8].*$/ /31\1/
rule 4 /^011/ //
rule 5 /^0031/ //
rule 6 /^703..../ /3120&/
rule 7 /^00$1.*$/ /\1/
voice translation-rule 302
rule 1 /^31207037333$/ /7037333/ type any subscriber plan any isdn
rule 2 /^7033$...$$/ /0207033\1/
rule 3 /^911$/ /112/ type any unknown plan any unknown
rule 4 /^31$670357575$$/ /0\1/ type any national plan any isdn
rule 5 /^31$107047444$$/ /0\1/ type any national plan any isdn
rule 6 /^12065015555$/ /&/ type any international plan any isdn
rule 7 /^12065015151$/ /&/ type any international plan any isdn
rule 8 /^12065015111$/ /&/ type any international plan any isdn
rule 9 /^15126026222$/ /&/ type any international plan any isdn
rule 10 /^12065011...$/ /&/ type any unknown plan any unknown
rule 11 /^15126022...$/ /&/ type any unknown plan any unknown
rule 12 /^....$/ /&/ type any unknown plan any unknown
voice translation-rule 303
rule 1 /^703.*/ /&/ type any subscriber plan any isdn
rule 2 /^010/ // type any national plan any isdn
rule 3 /^1/ // type any international plan any isdn
voice translation-rule 1000
rule 1 /.*$1...$$/ /206501\1/
rule 2 /.*$2...$$/ /512602\1/
rule 3 /.*$45..$$/ /020757\1/
voice translation-rule 1001
rule 1 /^1206...5...$/ /+&/
rule 2 /^1512...6...$/ /+&/
rule 3 /^31.0...7...$/ /+&/
voice translation-profile 1-HQ-Change_DNIS-Check_ANI
translate called 101
voice translation-profile 1-HQ-Proper_Types
translate calling 102
translate called 103
voice translation-profile 2-BR1-Change_DNIS-Check_ANI
translate called 201
voice translation-profile 2-BR1-Proper_Types
translate calling 202
translate called 203
voice translation-profile 3-BR2-Change_DNIS-Check_ANI
translate called 301
voice translation-profile 3-BR2-Proper_Types
translate calling 302
translate called 303
voice translation-profile SIP-NORMALIZE-DNIS-ANI
translate calling 1001
translate called 1000
voice-card 0
dspfarm
archive
log config
hidekeys
controller E1 0/0/0
clock source internal
pri-group timeslots 1-3,16
description == Voice Circuit to Branch2
controller T1 0/1/0
clock source internal
cablelength long 0db
pri-group timeslots 1-3,24
description == Voice Circuit to CorpHQ
controller T1 0/1/1
clock source internal
cablelength long 0db
pri-group timeslots 1-3,24
description == Voice Circuit to Branch1
interface Loopback0
ip address 177.1.254.254 255.255.255.255
interface Loopback10
ip address 177.1.254.250 255.255.255.255
interface Loopback11
ip address 177.1.254.251 255.255.255.255
interface FastEthernet0/0
description ==TO INTERNET==
ip address 192.168.1.150 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
description === To HQ
ip address 177.1.19.1 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:15
description == PRI Circuit to R3-BR2
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan resend-setup
no isdn outgoing ie network-facility
isdn outgoing display-ie
no cdp enable
interface Serial0/1/0:23
description == PRI Circuit to R1-HQ
no ip address
encapsulation hdlc
isdn switch-type primary-5ess
isdn protocol-emulate network
isdn incoming-voice voice
isdn negotiate-bchan
isdn outgoing display-ie
no cdp enable
interface Serial0/1/1:23
description == PRI Circuit to R2-BR1
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
isdn supp-service name calling
isdn negotiate-bchan resend-setup
isdn outgoing ie network-facility
no cdp enable
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 192.168.1.1
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
control-plane
voice-port 0/0/0:15
translation-profile incoming 3-BR2-Change_DNIS-Check_ANI
description == Voice PRI to Branch2
voice-port 0/1/0:23
translation-profile incoming 1-HQ-Change_DNIS-Check_ANI
description == Voice PRI to CorpHQ
voice-port 0/1/1:23
translation-profile incoming 2-BR1-Change_DNIS-Check_ANI
description == Voice PRI to Branch1
dial-peer voice 1 pots
description == All inbound calls from HQ BR1 BR2 into PSTN
incoming called-number .
direct-inward-dial
dial-peer voice 101 pots
description == Subscriber Calls from PSTN into CorpHQ
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^2065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 102 pots
description == National Calls from PSTN into CorpHQ
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^12065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 103 pots
description == International Calls into CorpHQ from PSTN Coming from NL Ph
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern ^0012065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 104 pots
description == + Calls into CorpHQ from PSTN Coming from Mobiles
translation-profile outgoing 1-HQ-Proper_Types
preference 1
destination-pattern +12065011...$
direct-inward-dial
port 0/1/0:23
forward-digits 10
dial-peer voice 201 pots
description == Subscriber Calls from PSTN into Branch1
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^5126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 202 pots
description == National Calls from PSTN into Branch1
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^15126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 203 pots
description == International Calls into Branch1 from PSTN Coming from NL Ph
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern ^0015126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 204 pots
description == + Calls into Branch1 from PSTN Coming from Mobiles
translation-profile outgoing 2-BR1-Proper_Types
preference 1
destination-pattern +15126022...$
direct-inward-dial
port 0/1/1:23
forward-digits 10
dial-peer voice 301 pots
description == Subscriber Calls from PSTN into Branch2
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^7033...$
direct-inward-dial
port 0/0/0:15
forward-digits 7
dial-peer voice 302 pots
description == National Calls from PSTN into Branch2
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^0207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 10
dial-peer voice 303 pots
description == International Calls into Branch2 from PSTN Coming from US Ph
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^01131207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 304 pots
description == International Calls into Branch2 from PSTN Coming from US Ph
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern ^31207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 305 pots
description == + Calls into Branch2 from PSTN Coming from Mobiles
translation-profile outgoing 3-BR2-Proper_Types
destination-pattern +31207033...$
direct-inward-dial
port 0/0/0:15
forward-digits 9
prefix 0
dial-peer voice 1000 voip
description == Calls into AT&T SIP ITSP for VC Week1 Lab1
rtp payload-type nse 99
rtp payload-type nte 100
voice-class sip localhost dns:sip1.att.com
session protocol sipv2
incoming called-number .
dtmf-relay rtp-nte
codec g711ulaw
dial-peer voice 5000 voip
service aa
destination-pattern A5000
session target ipv4:177.1.254.254
incoming called-number A5000
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
num-exp 1888....... 911
num-exp 1900....... 911
num-exp 1976....... 911
num-exp 1777....... 911
num-exp 1444....... 911
num-exp 0800....... 911
num-exp 0900....... 911
sip-ua
telephony-service
no auto-reg-ephone
max-ephones 1
max-dn 10
ip source-address 177.1.254.254 port 2000
caller-id block code *67
system message You WILL PASS this Exam!
voicemail A5000
max-conferences 8 gain -6
call-forward pattern .T
dn-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Sep 01 2012 15:29:37
ephone-dn 1 dual-line
number 12065015111 secondary +12065015111
label Seattle, US +1 206 501 5111
description INE PSTN Phone
name Seattle US Phone
ephone-dn 2 dual-line
number 15126026222 secondary +15126026222
label Austin, US +1 512 602 6222
name Austin TX Phone
ephone-dn 3 dual-line
number 31207037333 secondary +31207037333
label Amsterdam, NL +31 20 703 73 33
name Amsterdam NL Phone
ephone-dn 4 dual-line
number 12065015555 secondary +12065015555
label Hurley Mobile +1 206 501 5555
name Hurley's Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 5 dual-line
number 12065015151 secondary +12065015151
label Hurley's Home +1 206 501 5151
name Hurley's Home
call-forward busy A5000
call-forward noan A5000 timeout 12
ephone-dn 6 dual-line
number 31670357575 secondary +31670357575
label Sawyer's Mobile +31 6 70357575
name Sawyer's Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 7 dual-line
number 911 secondary 112
label US/EU Emer/FreePhone/Prem
name Emergency Services
ephone-dn 8 dual-line
number 15126026262 secondary +15126026262
label BLinus Mobile +1 512 602 6262
name Benjamin Linus Mobile
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 9 dual-line
number 31207037373 secondary +31207037373
label DHume Home +31 20 703 73 73
name Desmond Hume Home
call-forward busy A5000
call-forward noan A5000 timeout 16
ephone-dn 10 dual-line
number 31107047444 secondary +31107047444
label Rotterdam, NL +31 10 704 74 44
name Rotterdam NL Phone
ephone 1
device-security-mode none
mac-address A456.3040.0DAA
type 7975
button 1:1 2:2 3:3 4:10
button 5:6 6o7,8,5,4
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
ntp source Loopback0
ntp master 10
ntp server 64.90.182.55
end
CorpHQ#sh run
Building configuration...
Current configuration : 6353 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname CorpHQ
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone PST -8
clock summer-time PDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 177.1.11.1 177.1.11.14
ip dhcp excluded-address 177.1.11.21 177.1.11.254
ip dhcp excluded-address 177.2.11.1 177.2.11.14
ip dhcp excluded-address 177.2.11.21 177.2.11.254
ip dhcp pool CorpHQ-Phones
   network 177.1.11.0 255.255.255.0
   option 150 ip 177.1.10.10 177.1.10.20
   default-router 177.1.11.1
   dns-server 177.1.100.110
ip dhcp pool Branch1-Phones
   network 177.2.11.0 255.255.255.0
   option 150 ip 177.1.10.10 177.1.10.20
   default-router 177.2.11.1
   dns-server 177.1.100.110
no ip domain lookup
ip multicast-routing
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-ni
voice service voip
allow-connections h323 to h323
fax protocol cisco
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
no update-callerid
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice translation-rule 1
rule 1 // // type any subscriber plan any isdn
voice translation-rule 2
rule 1 // // type any national plan any isdn
voice translation-rule 3
rule 1 // // type any international plan any isdn
voice translation-rule 10
rule 1 /^[2-9].........$/ /9&/
rule 2 /^1[2-9].........$/ /9&/
rule 3 /^011/ /9&/
voice translation-profile MakeInternational
translate called 3
voice translation-profile MakeNational
translate called 2
voice translation-profile MakeSubscriber
translate called 1
voice translation-profile Prefix9_InFrom_CUCM
translate called 10
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller T1 0/0/0
pri-group timeslots 1-3,24
description == Voice Circuit to PSTN
interface Loopback0
ip address 177.1.254.1 255.255.255.255
ip pim dense-mode
interface FastEthernet0/0
description == To CorpHQ-Switch
no ip address
duplex auto
speed auto
interface FastEthernet0/0.10
description == Server VLAN
encapsulation dot1Q 10
ip address 177.1.10.1 255.255.255.0
ip pim dense-mode
interface FastEthernet0/0.11
description == Voice VLAN
encapsulation dot1Q 11
ip address 177.1.11.1 255.255.255.0
ip helper-address 177.1.10.10
ip nbar protocol-discovery
ip pim dense-mode
interface FastEthernet0/0.12
description == Data VLAN
encapsulation dot1Q 12
ip address 177.1.12.1 255.255.255.0
interface FastEthernet0/0.13
description == PSTN PHONE VLAN
encapsulation dot1Q 13
ip address 177.1.13.1 255.255.255.0
interface FastEthernet0/1
description === To PSTN
ip address 177.1.19.254 255.255.255.0
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 36
cdp enable
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To BR1
bandwidth 384
ip address 177.0.101.1 255.255.255.0
ip pim dense-mode
snmp trap link-status
frame-relay interface-dlci 101
ip rsvp bandwidth 136
interface Serial0/1/0.2 point-to-point
description == FR To BR2
ip address 177.0.201.1 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 102
ip rsvp bandwidth 136
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 177.1.19.1
ip route 0.0.0.0 0.0.0.0 FastEthernet0/0.10
no ip http server
no ip http secure-server
control-plane
voice-port 0/0/0:23
voice-port 0/3/0
voice-port 0/3/1
ccm-manager music-on-hold
sccp local Loopback0
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 1 register CorpHQ-729-MTP
associate profile 2 register CorpHQ-711-MTP
associate profile 3 register CorpHQ-HW-Xcode
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
codec ilbc
maximum sessions 2
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
translation-profile outgoing MakeSubscriber
destination-pattern 911
no digit-strip
port 0/0/0:23
dial-peer voice 11 pots
translation-profile outgoing MakeSubscriber
destination-pattern 9[2-9]..[2-9]......$
port 0/0/0:23
dial-peer voice 12 pots
translation-profile outgoing MakeNational
destination-pattern 91[2-9]..[2-9]......$
port 0/0/0:23
forward-digits 11
dial-peer voice 13 pots
translation-profile outgoing MakeInternational
destination-pattern 9011T
port 0/0/0:23
prefix 011
dial-peer voice 100 voip
description == Inbound/Outbound SIP PSTN GW From/To CUCM Pub
translation-profile incoming Prefix9_InFrom_CUCM
destination-pattern ^2065011...$
voice-class codec 1
session protocol sipv2
session target ipv4:177.1.10.10
incoming called-number .
ip qos dscp cs3 signaling
dial-peer hunt 1
sip-ua
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
ntp source Loopback0
ntp master 2
ntp server 177.1.254.254
end
Branch1#sh run
Building configuration...
Current configuration : 3838 bytes
! Last configuration change at 01:19:02 CDT Thu Oct 10 2013
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname Branch1
boot-start-marker
boot-end-marker
logging message-counter syslog
no aaa new-model
clock timezone CST -6
clock summer-time CDT recurring
network-clock-participate wic 0
network-clock-select 1 T1 0/0/0
dot11 syslog
ip source-route
ip cef
ip multicast-routing
no ipv6 cef
ntp update-calendar
ntp server 177.1.254.1
multilink bundle-name authenticated
isdn switch-type primary-ni
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller T1 0/0/0
pri-group timeslots 1-3,24 service mgcp
interface Loopback0
ip address 177.1.254.2 255.255.255.255
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.11
description == Voice VLAN
encapsulation dot1Q 11
ip address 177.2.11.1 255.255.255.0
ip helper-address 177.1.254.1
ip pim dense-mode
interface FastEthernet0/0.12
description == Data VLAN
encapsulation dot1Q 12
ip address 177.2.12.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn incoming-voice voice
isdn supp-service name calling
isdn bind-l3 ccm-manager
isdn outgoing ie facility
isdn outgoing display-ie
isdn outgoing ie redirecting-number
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 37
cdp enable
no frame-relay inverse-arp
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To HQ
ip address 177.0.101.2 255.255.255.0
ip pim dense-mode
snmp trap link-status
frame-relay interface-dlci 101
ip rsvp bandwidth 136
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
voice-port 0/0/0:23
ccm-manager fallback-mgcp
ccm-manager redundant-host 177.1.10.10
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
mgcp
mgcp call-agent 177.1.10.20 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp fax t38 ecm
mgcp bind control source-interface Loopback0
mgcp bind media source-interface Loopback0
mgcp profile default
sccp local Loopback0
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 3 register Br1-HW-Xcode
associate profile 1 register Br1-729-MTP
associate profile 2 register Br1-711-MTP
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous level 0 limit 20
line aux 0
line vty 0 4
exec-timeout 0 0
privilege level 15
logging synchronous
no login
line vty 5 15
exec-timeout 0 0
privilege level 15
logging synchronous
no login
scheduler allocate 20000 1000
end
Branch2#sh run
Building configuration...
Current configuration : 5789 bytes
! No configuration change since last restart
version 12.4
no service pad
no service timestamps debug uptime
no service timestamps log uptime
no service password-encryption
hostname Branch2
boot-start-marker
boot system flash:c2800nm-advipservicesk9-mz.124-24.T7.bin
boot system flash:
boot-end-marker
card type e1 0 0
logging message-counter syslog
no aaa new-model
clock timezone CEST 1
clock summer-time CEDT recurring
network-clock-participate wic 0
no network-clock-participate aim 0
dot11 syslog
ip source-route
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
no supplementary-service h225-notify cid-update
fax protocol cisco
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729r8
voice class custom-cptone JOIN-TONE
dualtone conference
frequency 300 3600
cadence 150 100 500
voice class custom-cptone LEAVE-TONE
dualtone conference
frequency 300 3600
cadence 500 100 150
voice translation-rule 1
rule 1 /^7033...$/ /020&/
voice translation-rule 10
rule 1 /^0/ /0&/
voice translation-rule 200
rule 1 /^206501...$/ /1&/
voice translation-profile 7DigitDNIS-to-10Digit
translate called 1
voice translation-profile Prefix0_InFrom_CUCM
translate called 10
voice translation-profile Prefix1-toCorpHQ-ANI
translate calling 200
voice-card 0
dsp services dspfarm
archive
log config
hidekeys
controller E1 0/0/0
pri-group timeslots 1-3,16
description == Voice Circuit to PSTN
controller E1 0/0/1
interface Loopback0
ip address 177.1.254.3 255.255.255.255
h323-gateway voip bind srcaddr 177.1.254.3
interface FastEthernet0/0
no ip address
duplex auto
speed auto
interface FastEthernet0/0.11
encapsulation dot1Q 11
ip address 177.3.11.1 255.255.255.0
ip helper-address 177.1.10.10
interface FastEthernet0/0.12
encapsulation dot1Q 12
ip address 177.3.12.1 255.255.255.0
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/0/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
isdn bchan-number-order ascending
no cdp enable
interface Serial0/1/0
description == Frame-Relay Circuit to WAN
no ip address
encapsulation frame-relay
fair-queue 64 256 37
cdp enable
no frame-relay inverse-arp
frame-relay lmi-type ansi
ip rsvp bandwidth
interface Serial0/1/0.1 point-to-point
description == FR To HQ
ip address 177.0.201.2 255.255.255.0
snmp trap link-status
frame-relay interface-dlci 102
ip rsvp bandwidth 136
interface Serial0/1/1
no ip address
shutdown
clock rate 2000000
interface Service-Engine1/0
no ip address
shutdown
router ospf 1
log-adjacency-changes
network 0.0.0.0 255.255.255.255 area 0
ip forward-protocol nd
ip http server
ip http authentication local
no ip http secure-server
ip http path flash:
control-plane
voice-port 0/0/0:15
translation-profile incoming 7DigitDNIS-to-10Digit
ccm-manager music-on-hold
sccp local Loopback0
sccp ccm 177.1.10.20 identifier 2 priority 2 version 5.0.1
sccp ccm 177.1.10.10 identifier 1 priority 1 version 5.0.1
sccp ccm 177.1.254.3 identifier 3 priority 3 version 5.0.1
sccp
sccp ccm group 1
bind interface Loopback0
associate ccm 2 priority 1
associate ccm 1 priority 2
associate ccm 3 priority 3
associate profile 4 register Br2-HW-Conf
associate profile 3 register Br2-HW-Xcode
associate profile 2 register Br2-711-MTP
associate profile 1 register Br2-729-MTP
dspfarm profile 3 transcode
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 4 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 1
conference-join custom-cptone JOIN-TONE
conference-leave custom-cptone LEAVE-TONE
associate application SCCP
dspfarm profile 1 mtp
codec g729ar8
codec g729r8
rsvp
maximum sessions software 10
associate application SCCP
dspfarm profile 2 mtp
codec g711ulaw
rsvp
maximum sessions software 10
associate application SCCP
dial-peer voice 1 pots
incoming called-number .
direct-inward-dial
dial-peer voice 10 pots
destination-pattern 112
no digit-strip
port 0/0/0:15
dial-peer voice 11 pots
destination-pattern 00[1-9]T
port 0/0/0:15
prefix 0
dial-peer voice 12 pots
translation-profile outgoing Prefix1-toCorpHQ-ANI
destination-pattern 000T
port 0/0/0:15
prefix 00
dial-peer voice 100 voip
description == Inbound/Outbound H323 PSTN GW From/To GK and CUCM Pub
translation-profile incoming Prefix0_InFrom_CUCM
destination-pattern 0207033...$
voice-class codec 1
session target ipv4:177.1.10.10
incoming called-number .
ip qos dscp cs3 signaling
dial-peer voice 101 voip
description == Outbound H323 PSTN GW To CUCM Sub
destination-pattern 0207033...$
voice-class codec 1
session target ipv4:177.1.10.20
ip qos dscp cs3 signaling
dial-peer hunt 1
telephony-service
max-ephones 1
max-dn 1
ip source-address 177.1.254.3 port 2000
max-conferences 8 gain -6
moh test.au
multicast moh 239.2.1.1 port 16384 route 177.1.254.3 177.3.11.1
transfer-system full-consult
create cnf-files version-stamp 7960 Sep 13 2013 18:55:27
line con 0
exec-timeout 0 0
line aux 0
line 66
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
login
scheduler allocate 20000 1000
ntp source Loopback0
ntp update-calendar
ntp server 177.1.254.1
end

GRC AC 10 SP13 - workflow not routing to multiple role owners

hello
We are experiencing issues in our production MSMP workflow where an access request with multiple business roles are not being routed to role owners after manager approval. The request contains four business roles. Three business roles have three different role owners. The fourth business role does not have a role owner assigned. After the manager approves the request, the business role without a role owner does not provision. The other three business roles do not route to their respective role owners. We have tested the same scenario in our development environment and it routes properly. I have validated our MSMP workflow settings in production and validated it was activated. I have also checked the instance monitor via GRFNMW_DBGMONITOR_WD and it does not give an indication why the request isn't routing.
Any ideas why we are seeing this? Below is a screen shot of the audit log.

Hi Stacey
If DEV is working and PRD is not have you gone through and compared both and ensure latest MSMP configuration in PRD has been activated?
Also, is the approver COCHGG00 also the Role Owner?
Are you able to show you MSMP configuration? It's makes sense to analyse the log in the context of your configuration. E.g. does the Z_ADDTNL_ACCESS_PATH path have two stages: Manager and Role Owner of which there is a routing rule on the Manager approval to go to the NO_ROLE_OWNER path where the business role has no role owner?
Regards
Colleen

WRT120N wireless nodes not routed to WAN, Multicast not working

Hi. Since a few weeks, I am experiencing strange and very annoying problems with my WRT120N. I have a DSL connection at home and the router connects to that via PPPoE. The LAN consists of one wired node and several wireless nodes. I have a G/N mixed setup because I also have G-only nodes (older laptop, mobile phone).
Every few minutes, my wireless nodes are not routed to the WAN anymore. Weird thing is: they can still connect to the wired node on the LAN so bridging seems to work fine. They can also connect to the router itself and the router says it is connected to the WAN. I can confirm this WAN connection because the wired node is being routed to the internet all the time. Restarting the router solves the problem. Actually, even if just disabling/enabling the wireless connection on my nodes solves it. However after a few minutes, sometimes seconds, routing stops working again (It happened twice during the writing of this email).
Another thing that is really bugging me is that multicast seems to get filtered. After a few minutes, no multicast message is being sent to the wireless nodes. Multicast packets sent by the wireless nodes do arrive at the wired node but any answer is being filtered on the router.
I have changed pretty much every possible setting that could be connected to the issue but no improvement (e.g. filtering multicast in the firewall). I used to be on 1.0.0.4 and hoped that upgrading to 1.0.0.5 would help but it didn't. I also checked this forum for solutions but found none that is working for me. This way, the router is pretty much useless for wireless clients as after an arbitrary but pretty short time interval they can only connect to the LAN and no Multicast service discovery/media streaming is possible. I really need help on these issues.

Hi Brickmonkey,
thanks a lot for your answer. I did the changes you advised. In fact, here's in detail what I did:
Router reset as described.
Changed the following configuration options:
PPPoE + Credentials
Local IP
MAC-IP Bindings for DHCP
Time Zone
DynDNS
Wireless Mode -> Mixed
SSID
Channel Width -> Auto
Wireless Security -> Enabled
Encryption AES
Passphrase
Port Forwarding for SSH,HTTPS
Router Password
Changed the options beacon interval, RTS threshold, fragmentation threshold and MTU as advised.
Router power cycled.
Routing and multicast are running since 5 minutes. Let's see if it lasts.
Answering your question: I do have one wired machine directly connected to the internal switch at the WRT120N. That's the one the ports are forwarded to. It has a static IP outside the DHCP range and is actually my DHCP,DNS etc server - however DHCP is disabled at the moment. All my other machines are wireless clients with G or N connectivity.
Can you explain the reason behind your proposed configuration changes?

Approval process monitor status turn to "Initiated" instead of "Pending", so awe is not routed

When I submit a transaction, after successful submission in approval process monitor the status has turn "Initiated" instead of "Pending". That's why it's showing "Not Routed" for the next approving person. So that worklist is not populated.
Please suggest me to resolve this issue.
Process Monitor as follows after submission:
Separation Approval Process (Stage)
Initiated (Monitor status)
Approval Routing from Unit HR (Path)
Not Routed    (Step)                                                    Not Routed      (Step)
Multiple Approvers                                                     Multiple Approvers
STATEHR ROLEUSER SEPARATION                              Central Hr
(Userlist)                                                                        (Userlist)

Looking at the error message "The Network Adapter could not establish the connection" , It appears hostname and port may be incorrect. Review the targets.xml under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\emd and
emoms.properties under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\config folder to make sure host ( sap_solman) and port (1527) are correct.
As far as setting the environment variables goes, you can go to control panel -> system -> advanced -> environment variables and set the ORACLE_HOME and ORACLE_SID
-Ramesh

Linksys E1200 Router not saving Port Forwarding changes

Hi!
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Can anyone assist me with this? I've searched for hours through forums and tech help websites, but I can't find anyone else with this issue.
Issue:
Linksys E1200 Router not saving Port Forwarding changes.
I have tried:
-Restarting the Modem
-Restarting the browser
-Restarting the computer
-Tried to Port Forward through both the Single and Ranged Port Forwarding

Hi there. You can try another browser or a different computer. If it is the same thing, upgrade the firmware of the router. You can refer to this link on how to http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0a6881b90224439b92c8d8f19ca42e5d_21511.xml&pid=80&...

VXML RINGTONE SERVICE Problem - Call is not routed to agents

We got below mentioned error in CVP Call Server logs for our calls. Due to this calls are not routed to agents.
Apart from our call flow, I need to know what is the cause and solution of this error.
Aborting XFER and disconnecting the caller code 488. RINGTONE SERVICE is not answering within 5000 millisecs, or the caller did not receive or accept the reinvite for ringtone media setup.
1646: 172.20.242.103: May 14 2014 11:50:07.701 +0300: %CVP_9_0_ICM-7-CALL: {Thrd=pool-1-thread-69-ICM-561} CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C, DLGID = 112 [IVR_LEG] - Processing ,, [MsgBus:CALL_STATE_EVENT], ssId=SYS_IVR1, eventId=DISCONNECT, causeCode=NORMAL_COMPLETION,, LEGID = , DNIS = 9555210577, ANI = sip:[email protected]:5060
1647: 172.20.242.103: May 14 2014 11:50:07.701 +0300: %CVP_9_0_ICM-7-CALL: {Thrd=pool-1-thread-69-ICM-561} CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C, DLGID = 112 [IVR_LEG] - Publishing ,, [ICM_EVENT_REPORT], dialogueId=112, sendSeqNo=2, eventId=DISCONNECT, causeCode=NORMAL_COMPLETION,, LEGID = , DNIS = 9555210577, ANI = sip:[email protected]:5060
1648: 172.20.242.103: May 14 2014 11:50:07.701 +0300: %CVP_9_0_ICM-7-CALL: {Thrd=pool-1-thread-69-ICM-561} CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C, DLGID = 112 [IVR_LEG] - Deleted dialogue. Duration: 0 hrs, 0 mins, 0 secs, 109 msecs
2017: 172.20.242.103: May 14 2014 11:50:07.717 +0300: %CVP_9_0_SIP-7-CALL: {Thrd=DIALOG_CALLBACK.7} CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C LEGID = 28D25F8E-DA6511E3-99A5DDDE-4246E36C - [INBOUND]: Reinvitation proceeding TRYING.
2018: 172.20.242.103: May 14 2014 11:50:12.685 +0300: %CVP_9_0_SIP-7-CALL: {Thrd=pool-1-thread-66-SIP-7351} CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C LEGID = 28D25F8E-DA6511E3-99A5DDDE-4246E36C - [INBOUND]: Called ring leg: CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C LEGID = 28D1273EDA6511E3999FDDDE4246E36C-140005740768575 - [RING-OUT]: status code = 0: elapsed msecs = 5000
2019: 172.20.242.103: May 14 2014 11:50:12.685 +0300: %CVP_9_0_SIP-3-SIP_CALL_ERROR: CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C LEGID = 28D25F8E-DA6511E3-99A5DDDE-4246E36C - [INBOUND]: Aborting XFER and disconnecting the caller code 488. RINGTONE SERVICE is not answering within 5000 millisecs, or the caller did not receive or accept the reinvite for ringtone media setup. (current=1 max=226) [id:5004]
2020: 172.20.242.103: May 14 2014 11:50:12.685 +0300: %CVP_9_0_SIP-7-CALL: {Thrd=pool-1-thread-74-SIP-7355} CALLGUID = 28D1273EDA6511E3999FDDDE4246E36C LEGID = 28D25F8E-DA6511E3-99A5DDDE-4246E36C - [INBOUND]: Waiting 2000 millisecs before terminating.
69088: 172.20.242.103: May 14 2014 11:50:12.873 +0300: %CVP_9_0_RPT-7-handleFakeNewCall: {Thrd=Thread-58} create fake New Call for >>HEADERS: (JMSType)=MsgBus:VXML_SCRIPT_DETAIL (JMSDestination)=Topic(CVP.VXMLSERVER.REPORT) (JMSTimestamp)=1400057412857 (ServerID)=cvp9lab2.SYS_VXML1:VXML:VXML1:cvp9lab2.MsgBus001 >>BODY: elementName=start elementid=1001871400057412857 timezone=Asia/Riyadh callguid=2BEF7F5ADA6511E399B0DDDE4246E36C localOffset=180 sessionname=172.20.242.103.1400057412842.21144.outbound ani=sip:172.20.243.187 howEventExited=1 sessionvars= sessionid=1001881400057412857 eventExitState=next uui=NA appName=outbound callStartDatetime=Wed May 14 11:50:12 AST 2014 elementTypeID=0 isNewCall=true vxmldatetime=Wed May 14 11:50:12 AST 2014 version=CVP_9_0 calltypeid=6 category=0 iidigits=NA dnis=sip:[email protected]:5060 >>STATE: isTabular=false isWriteable=false cursor=-1
69089: 172.20.242.103: May 14 2014 11:50:12.873 +0300: %CVP_9_0_RPT-7-handleFakeNewCall : {Thrd=Thread-58} 2BEF7F5ADA6511E399B0DDDE4246E36C onHold start time: Wed May 14 11:50:12 AST 2014

Hi,
//After that the agent goes to Reserved state but the call doesn't come through.//
I don't have experience on PCCE , but UCCE perspective this looks to me more like ATR(Agent Targeting rule) or Device Target Issue. Ringtone service should not cause Calls to fail.
Can you please post log from CVP, for Particular call that faced this issue?
Regards
Chintan

Server Timed Out, Router not detected

Ever since a heavy thunderstorm I have been unable to pick up wireless Internet on any of my wi-fi devices. I'm no longer able to access 192.168.1.1 through my Internet browser, when I tried to ping 192.168.1.1 it says Server Timed Out, and the LinkSys EasyLink Advisor program said my computer was unable to detect my router. Help?

Marcar,
its much easier for us to help if you give us a little detail. like the model & version of your device.
anyway, a thunderstorm aye?? ake sure that the router's power light is not blinking, if it is reset the router.
HOW TO RESET A ROUTER:
with router turned on, push on the little reset button on the back of the router (beside the wan/internet port). hold that button for about 30 seconds and then release and then turn the router off. leave it of for 20 seconds.
by then you can access the default IP of the router which is 192.168.1.1 (password: "admin").
BTW: before you reset the router make sure you know how to reconfigure it back again to work with the modem for your internet connection.

Dynamic Routing Not Working

I'm attempting to use dynamic routing (Dynamic Routing Action) to route to another proxy service and I keep getting "BEA-382000: Error preparing message for dispatch".
I'm using a lookup table:
<routingTable>
<route>
<relative-uri>/destination_1</relative-uri>
<route-to>DestinationOne</route-to>
</route>
<route>
<relative-uri>/destination_2</relative-uri>
<route-to>DestinationTwo</route-to>
</route>
</routingTable>
"DestinationOne" and "DestinationTwo" are local protocol proxy services that reside in two different projects.
To get the correct route-to value, my XQuery statement is:
routingTable/route/route-to[../relative-uri='{relative_uri}']
and I know it works.
At this point, the first proxy service (the one that does the routing) does nothing but use content from the $inbound variable to lookup the route-to information.
What am I missing?
Many thanks,
-Mark

We do this often.
I'm sure it can happen in other ways, but I see the error you're describing commonly in two scenarios:
1. An error occurred in the second proxy but you don't have an error-handler on that proxy (I've found it really helps to make sure there is an error handler on every proxy that at least logs the $fault and then does Reply with Success, otherwise ALSB sometimes loses the fault details). I think I usually get a BEA-38000 in that case, not a 38200, but off the top of my head I'm not sure.
2. If an AnySOAP proxy is calling an AnyXml proxy, I get this error. Recently we switched out endpoint to AnySOAP, and I had to go through and recreate all of the proxies to AnySOAP because previously they'd been AnyXml. Even adding error-handling to every possible level didn't give me any better details, I just happened to try the Any SOAP switch on one proxy and learned it fixed the error.
Hope that helps you track it down, at least there are some examples of what causes this error.
Meghan

5800 OVI map not routing

Hi All,
The sat nav on the 5800 is really good but I'm getting a slight issue with routing.
I searched an address by road and house number and county. It was found by the software but when I came to drive to it today I got a message "Route not found".
I then manually entered the postcode in the search bar and the route was then calculated correctly.
It isn't the first instance of this problem.
Any ideas as to why this has happened please?
Many thanks.

Did you download the new maps through maps updater .
It normally asks to delete old maps before installing new maps .
jje

CK11N , bom and routing not copied

Dear all,
At time of costing run through CK11N , bom and routing not copied I have checked all validity/ status /uses / lot size of bom and routing also . but when i will run costing for next month system has copied bom and routing .
plz guide me

Dear Surendra Patil,
Check the costing variant that you use for executing CK11N, is it PPC1?
If this is correct means check in T code OKKN and choose PPC1 and check for the quantity structure
control and check the BOM apllication and the routing selection ID.
This should match with your BOM that you have created and also the routing that you have created.
1. Check the BOM status in CS03---> header.
2.Check the status & usage of routing in CA03,generally it will be
Usage 1 Production
Status 4 Released (general)
3. If you are using Production version check whether have you assigned proper routing group & counter
and along with the BOM.Also check whether is the production version locked?
Check & Revert back.
Regards
Mangalraj.S

Workflow Process Manager - Could not route message to WfProcMgr with regist

Hi,
We recently started getting a strange error in our DEV environment:
Could not route message to WfProcMgr with registered key (null)
This is happening with the Server Component, Workflow Process Manager, and all services associated with this.
We are using Siebel v7.8.2.8. If anybody can provide any pointers, it would be of great help!
Thanks

Hi Trym,
Thanks for your time!
The target workflow that I am triggering from the WfProcMgr is a custom workflow and it does not have a BO defined. So, the Object Id should not be a mandatory field (I am in any case, not passing any Object Id). Nevertheless, whether I have an Object Id or I do not, I would assume that the Workflow would at least get triggered. I donot see as to why the Workflow would not trigger at all.
Though Siebel does act weird at times, I think the error I am getting is still somehow related to the actual cause! I would really like to understand as to where is this Registered Key stored in Siebel that it is continually searching for.
*When you say "Workflow Process Manager server component directly" do you mean like in a eScript
call in e.g. a Business Service?*
Please refer the second part of my previous post for this. I am trying through Server Requests BS and through Workflow Policies.
Thanks.

Router not routing!?

Similar Messages

Maybe you are looking for