Router set-up question

This is a basic question. I have a linksys router and Im replacing it with the airport extreme base station. I have a comcast modem too. How do I swap the routers? Do I just disconnect the ethernet cable from the linksys and connect to the airport then install cd and go from there? Will I have to reset the modem then and will I have to contact Comcast? Any help would be much appreciated.

Unplug the power to the modem. Swap the ethernet cables from the linksys to the Airport Extreme. Then power up the modem, wait about 1 minute, then power up the Airport Extreme, wait 1 minute then power up your Mac and setup the AE. You don't need to contact Comcast.

Similar Messages

I have a 3rd generation iPod Touch and just did the update to IOS 5. Now I can't connect to my Netgear wifi router. My iPhone connects fine along with all of my other laptops etc. I have the router set with WPA-PSK [TKIP] security and an access list.

I have a 3rd generation iPod Touch and just did the update to IOS 5. Now I can't connect to my Netgear wifi router. My iPhone connects fine along with all of my other laptops etc. I have the router set with WPA-PSK [TKIP] security and an access list. I've confirmed the mac address is included on that list and that the password is correct. Under choses netwrok I select the network and it just goes into a spin. I have tried removing the password and the access list settings and it still will not complete the connection to the router thus no internet access. The routers firmware is also up to date. This thing worked fine before this update and I've already tried to restore from backup. Any ideas or is the wifi nic bad in this thing with the new apple firmware update? Any fix?

Thanks Bob, I don't know why but it all of a sudden worked a few days later. It's a mystery but at least problem solved.

Code that handles a set of questions from database and place it on JSP

Hi,
How to write a code that handles a set of Quiz questions from database and place it on JSP page..
Thanks in advance
Haritha

975033 wrote:
Hi,
I hav got the answer from you r previous link, but not completly. I need help regarding on how to do code that handles a set of questions from database and place it on JSP.
Any help is highly appreciated.Yes but what kind of help do you expect to get? What kind of help do you think is possible through something as cold and distant as a forum, where you clearly require personal guidance and tutoring?
If you are going to answer "example code", I should warn you that the answers are not going to be to your liking.

How to create yes or no radiogroup dynamically for a set of questions

hi,
I am new to APEX.Depending upon my project requirement I need to create a set of questions with yes or no as radiogroup buttons,appended with a textarea for each question.For ex:
1.Name o Y o N [ "text area"]
The above line specifies the model I need.
Here text area is used for writing comments.
Now the question is how can I create them dynamically using apex_item.
Its very urgent.Kindly reply me soon.
Thanks in advance.

Thanks for ur quick reply.
But what actually I need is,I need to create the radiobuttons also dynamically.
I have created them by the following syntax,
select ename,apex_item.radiogroup(eno,'y' ) yes,apex_item.radiogroup(eno,'N')
from emp;
but the problem with this is ,
when I inserted yes for the first one it is taking and if i am giving the second one also as YES then it is not accepting ..means it is checking the second item by clearing the first one.
What I need is when I check the second one the first one should not get cleared.
Thanks in advance.

How to redirect user from login page to "Set Challenge question" page

How to redirect user from login page to "Set Challenge question" page (NOT custom page) after 3 un successful password attempts?
Meaning when user types wrong password 3 times they will be redirected to set Challenge question page. If user answers the challenge question then password reset page should be appeared other wise (after remaining 3 un successeful challenge question answers) account should be locked out.
thanks for your help.

hi sandeep
Thanks for your answer. Let me ellaborate more on the requirement here.
- Password Policy and Lost Password management are set up in the identity system
- Configure login tries allowed= 5. Verify accout is lock out after 5 unsucessful login.
This is what need to achieve.
1) If a user attempts to login 3(not 5) times using an incorrect login credential he/she should be redirected to set challenge question (security question) page.
2) Then if the user attempts (remaining) 2 times incorrect challenge answer then his/her account should be locked out.
3) If he/she answers the challenge answer correctly then he/she should be redirected to password reset page.
Is this possible?

Sets of Question Papers and answers for SAP ECC 6.0- FICO Module

Hi,
If anybody has some material on sets of question papers and answers of SAP ECC 6.0 FI- CO Material please mail the same on [email protected]
Useful replies will be awared points.
Regards
Milind Nair

Hi,
Please refer the below link and reward if helpful.
http://help.sap.com/saphelp_nw04s/helpdata/en/e5/de86f335cd11d3acb00000e83539c3/content.htm

Different user options with different sets of questions

Is there a way I can have two different options and when the user clicks on option A a whole set of questions/form fields appear. Or if they select option B a whole different set of questions/form fields appear?
How would I go about programming something like that?
Hopefully I was clear enough. Thanks so much! :)

Hi Arnold,
SAP Logon Tickets issued by the Portal contain two user ids, basically one for Java Systems and one for ABAP systems. See also note 843061 for details.
You do not need passwords for the reference system, if the user mapping is maintained by the user administrator, and the UM property ume.usermapping
.admin.pwdprotection is set to false, see http://help.sap.com/saphelp_nw04/helpdata/en/fe/d22a41b108f523e10000000a155106/frameset.htm. If you set the mapped user id programmatically, or if you retrieve it from an LDAP server, you also do not need to verify the ABAP password of the user (see https://media.sdn.sap.com/javadocs/NW04/SP12/ume/index.html and http://help.sap.com/saphelp_nw04/helpdata/en/0b/d82c4142aef623e10000000a155106/frameset.htm).
Best regards,
Joerg

Forcing Users to set Security Questions

Hi All,
Currently when a user joins the organization, the user can go to IdM user interface, login and set security questions. But this is an option only if user wants to use self service in IdM. So, it has been found that users are not setting it and it becaomes a pain when they call help desk for password change and help desk is not able to verify the user's identity because security questions are not set.
Please share your thoughts how other organizations are handling this situation.
Is there any way that we can force a user to set security questions when the user logs in first time?
Regards,
Gaurav

Hello,
In our Organization we did the following.
Under the Security tab there is a Policy tab.
There you should find a policy called: Default Identity Manager Account Policy.
Under Secondary Authentication Policy Options make sure "Enforce Answer Policy at Login" is checked.
In page help states:
Select this option to enforce the authentication question policy when the user logs in to this interface.
This solution works however it did become problematic while we had pass-thru authentication configured.
All the best
-IDMxml

SS7: How to display all route sets at once, can it be done?

BTS10200
Fairly new to softswitch world. Needing to see what route sets already exist. Is there a command I am missing to dump or show all routesets at once?
Thank You!

Additional features can be added by adding a feature, vsc, and service:
http://www.cisco.com/univercd/cc/td/doc/product/voice/bts10200/bts4_1/provgd/feature.htm
Here is a list of commonly assigned VSCs:
http://www.cisco.com/univercd/cc/td/doc/product/voice/bts10200/bts4_5/cli/cp/85apc.htm#

Presenter 8 -- need help with proper settings to allow quiz retake (with a NEW set of questions from a random pool)

We are publishing a Presenter 8 quiz to an LMS in a SCORM format. I am having trouble with the following: the quiz is built with multiple question groups, and a limited number of questions are being selected from each group. E.g. we have 80+ questions in total, and 25 are presented to a user on a given attempt.
When a user fails the quiz and exits the quiz normally, we want them to study and try again. I set the quiz settings to allow infinite attempts, and set the LMS settings to make sure the quiz is not presented in "review mode". When I test this quiz by failing it the first time, when I reenter the quiz, I am taken to the last slide in the quiz (which is the last one I viewed), and I can retake the quiz by navigating back to the first question.
Here's the problem: I am presented with the SAME set of questions, rather than a NEW set of random questions. This will facilitate cheating (all a user has to do is take the quiz once, review the answers, and then take it again to pass it).
How do I insure that the user is presented with a NEW set of questions when I retake the quiz?
I am open to upgrading to Adobe Presenter 10, but would rather not have to do so. There must be some setting I'm missing.
Scott Richardson

If you move a mailbox from one server to another, Outlook will automatically repair the Outlook profile. Have you tried this, instead of trying to force a profile update using a PRF?

How to install Twitter app without setting security questions?

Hello! I recently registered a Twitter account. iOS 6 includes Twitter integration - great. When I navigate to Settings - Twitter and tap the Install button, a dialog shows up: "Improve your Apple ID security" and "Set security questions" blah blah. There are two buttons in the dialog, "Set questions" and "Cancel". If I tap Cancel, Twitter app download doesn't begin and Twitter icon disappears from my SpringBoard. If I tap "Set questions", I need to answer some stupid questions. If I leave answer boxes empty, I can't continue. I will not set any security questions for my Apple ID, that's for sure.
How I can install Twitter app?

I just encountered the same problem when I tried to download Twitter on my husband's new iPhone 5. There was no problem when I installed Twitter on my iPhone 3GS yesterday :-(
You've probably seen by now that there are many, many people who are having problems with the 'Help improve Apple ID security' message - not confined to iPhone but also on iTunes, iPod Touch, iPad etc.
I chose the 'Not Now' button on his iPhone 5 and the Twitter app wouldn't allow me to proceed ....
Looks like Apple aren't in any hurry to fix this because people have been complaining about it for months (after all, your post is more than 3 months old and the problem is still occurring).
Were you ever able to activate Twitter on your iPhone 4S?
Tricia

Hi .. I can not re- set the questions of confidentiality in order to forget the answers in my account

Hi .. I can not re- set the questions of confidentiality in order to forget the answers in my account

If you aren't getting the reset link on the Password & Security section of your account on http://appleid.apple.com then you don't have a rescue email address (an alternate email address is different), and you won't be able to add one until you can answer your questions - you will have to contact Support in your country to get the questions reset.
Contacting Apple about account security : Contact Apple for help with Apple ID account security
If your country isn't on that page then try this form and explain and see what they reply with : https://ssl.apple.com/emea/support/itunes/contact.html
When they've been reset you can add a rescue email address for potential future use : Manage your Apple ID primary, rescue, alternate, and notification email addresses

My family owns an Apple Airport router, and my question is that is there a were to remotely access the router and turn it off and on? Thanks

My family owns an Apple Airport router, and my question is that is there a were to remotely access the router and turn it off and on? Thanks

Richard's suggestion will turn off and turn on the wireless function on your Mac computer......but.....it will not do anything as far as turning your Apple AirPort router on and off.......which seems to be the question that you are asking above.
If this is the question that you are asking, it is not possible to power the Apple router on and off from either a local or remote location.

HT5312 I forgot my security questions and I don't have a rescue mail, how I can set new questions? Or retrieve the old?

I forgot my security questions and I don't have a rescue mail, how I can set new questions? Or retrieve the old?

Apple ID Security -
Telephone Apple Care for your country and ask for the Account Security Team, then request help resetting the questions.

Recovering static routing setting 10.1.10.1 for CUE

I'd like to recover connectivity with CUE.
I deleted default static routing setting 10.1.10.1 for CUE by my mistake.
I tried to configure like followings.
UC520#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
UC520(config)#interface Loopback0
UC520(config-if)#description $FW_INSIDE$
UC520(config-if)#ip address 10.1.10.2 255.255.255.252
% 10.1.10.0 overlaps with Vlan101
UC520(config-if)#ip access-group 101 in
UC520(config-if)#ip nat inside
UC520(config-if)#ip virtual-reassembly
UC520(config-if)#interface Integrated-Service-Engine0/0
UC520(config-if)#description cue is initialized with default IMAP group
UC520(config-if)#ip unnumbered Loopback0
UC520(config-if)#ip nat inside
UC520(config-if)#ip virtual-reassembly
UC520(config-if)#service-module ip address 10.1.10.1 255.255.255.252
Need IP address to be configured on interface Integrated-Service-Engine0/0
It seems like ip adress setting failed because of overlapping with Vlan101. Also CUE Connectivity Diagnostics says "IP address needs to be configured on interface Integrated-Service-Engine0/0"
Use reset only to recover from shutdown or failed state
Warning: May lose data on the the NVRAM, nonvolatile file system or unsaved configuration!
Do you want to reset?[confirm]
Trying to reload Service Module Integrated-Service-Engine0/0.
UC520#service-module Integrated-Service-Engine 0/0 session
IP address needs to be configured on interface Integrated-Service-Engine0/0
UC520#
I'm a beginer of IOS, Cisco products and also English. I can barely use CCA. Thank you.

Check in flash there should be a default configuration file with basic settings.

Router set-up question

Similar Messages

Maybe you are looking for