Router Setup Web form display problem

When I open Internet Explorer 6 to my router setup page (192.168.1.1), the menus and control discriptions are missing. Internet explorer reports an error with processing some of the web scripts. I'm using: WRT54G V8. I have tried reseting the router but it does not fix the problem. I have tried using the Opera Browser but it has the same problem. Unfortunately, I can't attach a screen capture to this post. Any help would be greatly appreciated. Thanks, mm

I did some playing around and found that in "Save Mode" the setup web form displays properly. So I upgraded the router firmware in Save Mode, rebooted and now the setup form displays fine in regular mode. I should note that I also re-installed ZoneAlarms (firewall application). Thanks, mm

Similar Messages

WRT160N v3: Cannot connect to router setup web page with current Firefox or IE

Every time I try to connect to the admin page of my router, I get "The connection to the server was reset while the page was loading." This happens with FIrefox 11, and started when I upgraded to 8 or 9. A machine running FF 3.6 does not exhibit this problem; I get right in. What IE 9 says is "Internet Explorer cannot display the webpage" (after complaining about the expired certificate).
I ran Wireshark to see if I could learn anything, but all I could figure out was this:
https handshake was OK.
First TLS packet is received by router, which then immediately issues a reset and ends the connection. I don't know why.
Has anyone seen this? or have I got a screwed up configuration (or router)?
Solved!
Go to Solution.

castor wrote:
"The connection has timed out", seems to affect servers at MozilllaZine, for Firefox on Windows...
I'm not sure what this has to do with my problem; my difficulty is only in trying to talk to the router configuration page. Everything else works just fine.
~~ Tools > Options
~~ Advanced (tab) -> Network (tab) > "Setting"
~~ (X) Auto-detect proxy setting for this network
I have "use system proxy settings". Since this is a home network and I'm not using a software proxy on my machine, I know there is nothing between me and the router.
Second, let me know if you have enabled 'https' in the router management page. What is the IP address on the computer when connected to the router. To check the IP address that you are getting from the Router... You can check the IP address in the following manner:
# Click on Start -> All Programs -> Accessories -> Command Prompt.
# A black pop up box should come up, type: "ipconfig /all" …
This is not going the right direction, but to satisfy your curiosity:
   IPv4 Address. . . . . . . . . . . : 10.244.122.142(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 10.244.122.1
   DHCP Server . . . . . . . . . . . : 10.244.122.1
These are correct. (Since my telco DSL has me behind its own NAT router and has assigned my modem address 192.168.1.2, so I could not use Cisco/Linksys's manufacturer default address settings.)
There check the IP address and Default Gateway under LAN….
If it provides the valid IP address then try to connect the router to a different computer and then try to open the router setup page...
I have a linux virtual host (thanks to VMware) now running Firefox 5, and it can talk to the router setup page just fine, once I accept and save the invalid certificate the router presents, at https://10.244.122.1. So I conclude the problem is to do with the later version of Firefox (currently 11, but I had this problem with 10 and maybe with 8 and 9).

Web Forms Printing problem

Hi all,
I am facing a problem in printing the webforms (Forms6i), in Netscape its printing a blank page whereas in IE its printing a black page . Everything else can be printed from the browsers successfully but only the problem is being faced when Oracle forms are being tried to printout.
Plese suggest any solution whoever have faced this problem and has set it.
Thanx in advance.

Forms are not intended for printing - it is very unusual to print the form. If he needs to do this the only safety way I know is to press ALT/Print_Screen on the keyboard and to paste the result in Word.
If your user needs hardcopy, create Report and start it. Do not use run_product on the web for invoking reports - use web.show_document and reports server.
The reports can be printed on LAN and WEB much easier as Forms.

Web site display problems

All work OK on Chrome and IE, but FF has many problems. Worked fine until a few days ago. Downloaded latest version did not help. Google search from home page goes to an almost blank page. Nothing to click, Home page (earthlink) shows much more info than in Chrome or IE. Many pages do not display right (eg NBA.com) where top 4" is missing or do not display at all. Again, all work fine using chrome or IE.

This is likely a box model issue, common with IE. First, ensure that you have a valid DOCTYPE declared in your document. Second, check the padding and margin setting on all of your CSS elements (this is probably one of the most easily accessible box model articles on the web). Third, start tweaking your code, cursing, praying...and finally, tell everybody you know to stop using browsers that don't meet web standards

Icon display problem in web form

Hello,
I am running form through browser. i have converted all my ico files to gif. but icon on the button in web form is not rightly positioned and not clearly displayed as it was in client/server(ico file).
please help me out.
thanks
abhishek

Hi,
it may be that Forms requires your buttons to be a bit bigger in size after converting .ico file to .gif. However, the icons are referenced by a URL link and therefore shouldn't be of a lower quality. At least it should have the same display quality as it has when opening teh gif in a Browser.
frank

Receive ping throw WRT54G setup but cannot display web-pages.

Hi
I have a WRT54G router, connected to the same DSL modem for 4 years and everything was fine till last week. Since last week, i cannot display any web pages, despite the fact that i am connected to my ISP (it was checked with there support team).
I have 3 different laptops and 1 desktop with different browsers and different OS (XP, VISTA) on them and same antivirus (AVAST!).
I receive pings from all the laptops and desktop to the router (ping 192.168.1.1), which mean that they connect probably to the router
I was able to receive ping from different websites throw the router setup (192.168.1.1) under "Administrator" tab and then under "diagnostic" tab, But I cannot display any web pages.
Does any one might know what may be the problem?
Thank you.

Thank you for the quick respond.
I connect the computer directly to the modem and it work just fine.
When I ping throw command prompt in the computer (connected to the router) I receive the next massage "bla bla bla o recevie bla bla 5 packet loss or something".
I was able to receive ping from different websites throw the router setup (192.168.1.1) under "Administration" tab and then under "diagnostic" tab.
The problem was solved yesterday by updating the firmware and reseting the router with the reset button.
Very wired.
Anyone have any idea what may was the problem?

Weird icon display problem (9iAS Forms 9.0.4)

Let me start out with the fact that I have setup 6 or 7 systems displaying GIF's as icons in web forms (both Forms 6i and Forms 10g/9.0.4). So I know all about setting the registry.dat, virtual directory for the icons etc. I have setup the environment correctly (unless some fat finger typing has gotten in the way).
When I load a form in a web browser and I watch the status bar on the bottom of the broweser ( IE6 or IE7) I can see that it loads the GIF's (fortunately my server is just slow enought that I see the "loading .....xyz.gif" statements for my GIF icons.
What happens is that none of the icons display on the buttons. Of course when I run the form in the IDE the icons display as expected.
Has anyone run into this problem before and if what was the solution?
TIA,

1. The image files cannot be found or are not accessible. Just because you see something on the client that says "Loading..." does not necessarily mean it was found. Check the HTTP Server error_log. If you see HTTP 404 errors you have an access or virtual path problem.
Answer: No HTTP 404 Errors (no errors at all). FYI, Files are located in D:\icons (W2K server) and the Security is set to "Everyone" with Full Access/Control. The AS has "D:\icons" mapped to /icons and Registry.dat has the path set to /icons.
2. You are using an image format that isn't supported. For example, Forms supports GIF files, but not GIF files with transparent backgrounds. Also, Forms does not support most of the compression formats associated with GIF and JPG. Test with an image that you know will work. For example the OTN Logo on this page. Right click on the image and choose Save Picture As.... or:
http://www.oracle.com/admin/images/otn/otn_logo_small.gif
Actually, you should be able to simply put the entire URL above into the image filename field on the Property Palette for any Iconic button large enough to hold it.
I pretty sure this works in 10.1.2, not so sure about 904
Answer: You'll probably say this is not good enough, but the images work in the IDE, therefore I conclude that they should work on the AS (i.e. size and display type are correct/supported). I did not have a button that was big enough for the Oracle logo, hence I did not try it.
3. The image size is too large for the button.
Answer: see answer above.
4. References to images are case sensitive. It is recommended that your image files (in the file system) use all lower case letters, including the extension. The reference in the form should also be lower case.
Answer: all image names in the property pallet are lower case and the actual file names are lower case (as shown in Windows Explorer).
With regard to the other post about icon names ending a list of specific characters, some do and some don't, but ALL my icons are NOT displaying.
Lastly, these exact same icons have worked in the past (who does not reuse icons?).

WEB Forms do not display properly with windows 95 LARGE fonts desktop setting

Hi,
We are using WEB forms 6.0 patch level 6 (We tried 6i but had too many bugs with it, we prefer to wait until at least a couple of patches are out, installation was a VERY painful experience for us)
We still have the following problem with WEB FORMS deployed on win95 desktops with LARGE FONTS destktop settings: The forms are not displayed correctly, sometimes there are no scroll bars, resizing a window gives weird results, part of the forms become inaccesible, some forms are blank, etc...
Can you verify or confirm that you have the same kind of problems ? We use jinitiator 1.1.18.
Is it fixed with 6i ? Is it fixed wit jinit 1.1.27 ?
We develop in smal fonts on win95 and recompile under solaris before deploying.
Thanks
null

Thank you all for your fast asnwers. The "Use hardware acceleration when available" was the problem, I disabled it and I will post a message on my site about this.
The site is on-line in the same aspect since 2005, modifiyng the whole site to fit with Firefox11's default setting is not a good option. At that moment, placing a tabel (alligned to the center of the page) and puting in it the thumbnails with links generated by ExpressThumbnailCreator, than manually adding the description in the HTML view of FrontPage was the simplyest way possible to make the site appear properly on my 800*600 px resolution I used then. Of course, I upgraded my hardware and software since then, but the site remained mostly unchanged (except the index and a few files). I know it's time for a new version of the site but... my web-design knowledges are limited to basic HTML.

Unable to access the Router's Web-Based Setup Page

Hey, I found a little problem when I tried to change the configurartions to my Linksys WRT54GS ver- 6.0 router. Problem is that I can not acces to setup, nor can I connect to Internet trough wire. Can somebody help me with my problem?
Pasi

To view the router's web pages:
You do not need an Internet connection. The router's "web pages" are built into the router.
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
Point your browser to 192.168.1.1 , then login to your router. Your user name should be left blank. Your password is "admin" (with no quotes), unless you changed it.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker, and the Ad blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Report back with this problem, and also state the make and exact model number of your modem (not the router).
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.

WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page

WRT54GX4 - Difficulties Accessing the Router's Web-Based Setup Page.
I have tried everything posted to the forums and the Knowledge Base for several weeks now with no luck. I can power push router and gain access to router's web-base interface but only for a few minutes than it quits loading part way through and or does not load at all. If I turn off the wireless side I can access the router at will with no problems. My warranty is almost over. I am at my wits end. I would like to get it replaced under warranty if I can. (^8
Solved!
Go to Solution.

Thank you for your recommendations peanuts. (^8
I bought the router back in December 10, 2006.
I updated the firmware to v1.00.20 back in June 2007. After I did a successful firmware upgrade I reset the router to factory default settings and then reconfigured it. It has worked Ok till a couple of months ago.
I have read everything I can find here on the support forum and in the Knowledge Base several times.
I have tried changing all the different settings to the different recommendations posted here and in Knowledge Base with no success. Each time I would do a long reset back to factory defaults, let it soak for a few hours and then make one change at a time and let it soak.
I have been monitoring 6 other wireless AP(s) around me (none mine) for a couple of months too. None of them are strong enough to connect to. My SSID is different from them. I have tried all the channels. My router is passworded and MAC'd.
It is looking like it is time to call support and try to get a replacement under warranty while it is still in affect.

Error in router's web-based setup page (WRT54G V5)

Hi,
My router’s web-based setup page is unable to load fully.
There seems to be an error with some document.setup.save file.
I have tried to reset my router but the router’s web-based setup page is still unable to load fully.
Please help.
Thanks.

Try Internet Explorer, it usually works.
JavaScript must be enabled.
Temporarily turn off your computer's software firewall, and see if that corrects your problem.
Hope this helps.

How to retain focus in Web forms 6i item when displaying pdf image

How to retain focus in Web forms 6i item when displaying pdf image in a multi-record block?
Hello.
I have a Web Forms 6i program (version Forms 6.0.8.19.2) running in a 3-tier application. The web form program has a multi-record block containing invoices. When navigating to a record, the form should display the PDF invoice image which is stored in an Oracle 8.1.7 database as a BLOB in another window. When user press down-arrow, the next PDF invoice image should be displayed.
I am able to accomplish the functionality above by using web.show_document('URL', target') in the when-new-record-instance. The URL being called is a PL/SQL Web Toolkit stored procedure using wpg_docload.download_file built-in.
The problem is that the focus is lost on the Webform and the focus is shifted to the PDF image window when you navigate to the next record using down-arrow. I want to retain the focus in the form as this is a data-entry form, the operator will use down-arrow to go to the next-record rather than the mouse. I also only want to do this for this Invoice Entry form and NOT to all forms.
Please advise how to resolve this problem. Thank you.
Regards,
Armando

Magesh,
the issue of a SSO protected form showing the logon dialog is a knwon issue for Windows200 and the Oracle9iAS base release. If you applied Forms Patch 1 then this should be solved. Hope that I am right in that you are using Oracle9iAS and not Oracle9iDS. Do you see the Single Sign-On logon screen or the Forms logon dialog directly? Check the forms90.conf file in teh forms90/server directory as this contains the Form sso settings (mod_osso) which by default is commented out and therefore inactive. You need to remove the commenting '#' characters and make sure that each sentence having a '#' in front, after that starts on a new line.
The Forms deployment documentation within the Oracle9iAS docu provides this information too.
Frank

WRT54GS router setup page won't display most text

So I bought a new Linksys WRT54GS v6 wireless router yesterday, and I was able to set it up to share my DSL line, but when I went to the router setup page (192.168.1.1), it wouldn't display most text. It displays text in the entry boxes, but there are no links or other text on the page. I took a screenshot which can be seen here: http://img87.imageshack.us/img87/3390/routersetuppagemc1.jpg
Does anyone know what I can do to solve this issue?

Hey Merugo. I was having the same problem with the router settings screen refusing to load for my WRT54G. Do you happen to have v.5 of the router? After digging around in the help files on the site, I found this for firmware recovery for the WRT54G v.5 and it fixed the problem I was having once it loaded the updated .bin. Blank screen be gone.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3176
(The first time the router tried to load the new .bin it timed out. And the second time it installed correctly though it didn't display "Upgrade Success" like it's apparently supposed to.)
Hope this can maybe help you since it fixed things for me.Message Edited by Res on 10-03-200606:44 PM

A webpart or web form control on this page cannot be displayed or imported.The type could not be found or it is not registered as safe.

Hi,
After moving my files from SP 2010 to SP 2013 , for all my web parts i am getting A webpart or web form control on this page cannot be displayed or imported.The type could not be found or it is not registered as safe. error. I checked web.config files
and they are there as safe control and trust level is also full.
These webparts work in 2010.
Do i need to tweak something in code or distributed cache to make this thing work? The errors i see are
Error importing WebPart. Assembly c , Version=1.0.0.0, Culture=neutral, PublicKeyToken=216eaf49984a9b29, TypeName. C. A Web Part or Web Form Control on this Page cannot be displayed or imported. The type c Version=1.0.0.0, Culture=neutral, PublicKeyToken=216eaf49984a9b29
could not be found or it is not registered as safe.
Getting Error Message for Exception Microsoft.SharePoint.ApplicationRuntime.SafeControls+UnsafeControlException: A Web Part or Web Form Control on this Page cannot be displayed or imported. The type C Version=1.0.0.0, Culture=neutral, PublicKeyToken=216eaf49984a9b29
could not be found or it is not registered as safe.
at Microsoft.SharePoint.WebPartPages.WebPartImporter.CreateWebPart(Boolean clearConnections)
at Microsoft.SharePoint.WebPartPages.WebPartImporter.Import(SPWebPartManager manager, XmlReader reader, Boolean clearConnections, Uri webPartPageUri, SPWeb spWeb)
at Microsoft.SharePoint.WebPartPages.WebPartGalleryItemBase.InstantiateFromXml(XmlReader reader)
at Microsoft.SharePoint.WebPartPages.WebPartAdder.SiteWebPartGalleryProvider.SiteWebPartGalleryItem.Instantiate()
at Microsoft.SharePoint.WebPartPages.WebPartGallerySourceBase.AddItemToPage(WebPartZoneBase zone, Int32 zoneIndex, WebPartGalleryItem item, String wpid)
at Microsoft.SharePoint.WebPartPages.WebPartAdder.System.Web.UI.IPostBackEventHandler.RaisePostBackEvent(String eventArgument)
An error occurred while attempting to add the gallery item [Custom] c to the page. The error was: Microsoft.SharePoint.ApplicationRuntime.SafeControls+UnsafeControlException: A Web Part or Web Form Control on this Page cannot be displayed or imported. The
type c Version=1.0.0.0, Culture=neutral, PublicKeyToken=216eaf49984a9b29 could not be found or it is not registered as safe.
at Microsoft.SharePoint.WebPartPages.WebPartImporter.CreateWebPart(Boolean clearConnections)
at Microsoft.SharePoint.WebPartPages.WebPartImporter.Import(SPWebPartManager manager, XmlReader reader, Boolean clearConnections, Uri webPartPageUri, SPWeb spWeb)
at Microsoft.SharePoint.WebPartPages.WebPartGalleryItemBase.InstantiateFromXml(XmlReader reader)
at Microsoft.SharePoint.WebPartPages.WebPartAdder.SiteWebPartGalleryProvider.SiteWebPartGalleryItem.Instantiate()
at Microsoft.SharePoint.WebPartPages.WebPartGallerySourceBase.AddItemToPage(WebPartZoneBase zone, Int32 zoneIndex, WebPartGalleryItem item, String wpid)
Adit

Hi Adit,
According to your description, my understanding is that the error occurred when you deployed the .wsp files to SharePoint 2013.
I recommend to check if all the assemblies are put into the BIN and GAC.
If above cannot work, you can check the troubleshooting steps in the link below:
http://www.bluedoglimited.com/SharePointThoughts/Lists/Posts/Post.aspx?ID=189
Best regards.
Thanks
Victoria Xia
TechNet Community Support

How to setup a purchase discount on my web form?

How to setup a purchase discount on my web form? I use adobe form central and my wix web page only allow me to insert ready host form URL.

Hi,
I believe you want to embed a form on your web page. Please take a look at this link, http://forums.adobe.com/docs/DOC-1991 and see if it works with your web page. I am not familiar with wix websites tools, but if after trying it out with the instructions on how to embed the form, and does not work, maybe you can provide the FormsCentral web form URL on your web page. Your end users visit your web page, click on the web form URL link and the form will open in a new browser.
To get the FormsCentral web form URL, open the form, go to Distribute Tab / Web Form sub-tab and select "Copy Link", then paste the link on your web html page.
If you want to set up your form to work with PayPal for payment transaction, please see this link: http://forums.adobe.com/docs/DOC-1632
Hope this helps,
Thanks,
Lucia

Router Setup Web form display problem

Similar Messages

Maybe you are looking for