Router stops all traffic randomly, why?

I recently bought a slingbox. My problem has been, since I hooked it up, it constanly broadcast streaming video out to their servers so I can access it from anywhere. Since I installed it, after a few hours of running, it stops transmitting all data. Is there a cap on what it will process outgoing before it stops, and if so, how do I remove that?

hi , what router are u using ? what are your current settings ?? also ensure that u have the latest firmware for the router.

Similar Messages

SonicWall SourceNAT VPN setup as default route for all traffic!

Hi,OK hope someone can help with this mess.....Our customer has been taken over by a US company who have said all outgoing internet traffic must go via their data centre. They want us to create an IPSEC vpn from our SonicWALL TZ215 to them then route all traffic locally via this VPN.In principle this didn't sound too bad. Then there were some more options:Our local subnet 172.x.x.x has to be NAT'd to a single /32 address. 192.x.x.131They also require our destination network to be set as 0.0.0.0. as they wont specify the range at the datacenter.I have managed to get the VPN up but using the the NAT address as my local subnet and using the option on the SonicWALL "Use this VPN Tunnel as default route for all Internet traffic" on the remote network. Phase 1 and Phase 2 work ok. The problem i now have is i need to route all LAN traffic...
This topic first appeared in the Spiceworks Community

Hi Norbert,
I am sorry to say that configuring routes in Azure Virtual network is not supported. I recommend you to submit your reuqirement on Azure Feedback and hope it would be released soon:
http://feedback.azure.com/forums/217313-networking-dns-traffic-manager-vpn-vnet
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

RV016 Router Allow All Traffic For Outside IP

Hi,
I need to configure the firewall to allow all traffice for an IP address of a sever. What steps in the router do i need to configure this? This is a cloud based voip server and we have IP phones and we need to add an IP address of the phone server to allow all traffic for that IP.
thanks.

Hi Jonathan,
I have a similar problem with VOIP traffic being dropped by my new RV016 v3 router.
I have created one Firewall Rule, to allow ALL traffic from the external VOIP PBX provider (single IP) to connect to the internal VOIP phones, which have assigned addresses in a small IP Address range (eg. 10.1.2.50 - 10.1.2.59)
The Aastra VOIP phones continually loose their registration wtih the cloud-based PBX. If you make an outgoing call, it will work, but the PBX will lose connection with the phone, 3 or 4 minutes after you hang up, and will mark it as offline. Incoming calls made within the 3 or 4 minutes will get through, but after that they go right to voicemail on the PBX system.
We used to have an RV016 v2 router and VOIP traffic worked OK, with a similar Firewall Rule. We replaced the v2 router because its CPU crashed.
I tested the VOIP traffic with a WRT160 router with minimal Firewall Rules, and it works OK, as long as SIP-ALG is turned Off. We want to use the RV016 because it provides a larger number of ports for our LAN.
Any suggestions ?
Kirk

(High Ip input) on My router , I need to troubleshoot why CPU is high !!!!

(High Ip input) on My router , I need to troubleshoot why CPU is high !!!!
=================
i have a cisco router 7200 NPEG2 processor , worked as LNS for PPPOVPDN circuits (Router for ADSL clients)
i have "high ip input on my processor" and there is alot of differnce on my router between operations done by cef and operations done by router cpu
as an example , lets make show cpu process sorted
CPU utilization for five seconds: 67%/54%; one minute: 67%; five minutes: 68%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 10837056 46891299 231 6.31% 6.04% 6.32% 0 IP Input
122 4081972 38214106 106 2.47% 2.36% 2.46% 0 L2X Data Daemon
270 467844 2089101 223 0.79% 0.78% 0.79% 0 PPP Events
275 1862224 2102444 885 0.71% 0.73% 0.71% 0 SNMP ENGINE
112 627104 93588 6700 0.39% 0.36% 0.37% 0 CEF: IPv4 proces
273 854004 4207368 202 0.31% 0.26% 0.24% 0 IP SNMP
52 453256 12321 36787 0.31% 0.31% 0.31% 0 Compute load avg
258 295540 701580 421 0.23% 0.17% 0.15% 0 RADIUS
142 45792 14107303 3 0.23% 0.21% 0.21% 0 HQF Shaper Backg
78 86532 166975 518 0.23% 0.17% 0.13% 0 ACCT Periodic Pr
260 483164 248673 1942 0.23% 0.19% 0.24% 0 L2TP mgmt daemon
272 63980 1073491 59 0.15% 0.16% 0.15% 0 IPHC Admin
77 111560 184597 604 0.15% 0.08% 0.06% 0 AAA ACCT Proc
261 330572 217566 1519 0.15% 0.12% 0.15% 0 L2TUN Applicatio
274 450584 2102164 214 0.15% 0.15% 0.15% 0 PDU DISPATCHER
16 152352 1081873 140 0.07% 0.08% 0.19% 0 EnvMon
279 229040 27298 8390 0.07% 0.10% 0.11% 0 VTEMPLATE Backgr
40 23704 53593 442 0.07% 0.03% 0.02% 0 Net Background
95 4512 55604 81 0.07% 0.00% 0.00% 0 PPP Hooks
109 6844 62029 110 0.07% 0.00% 0.00% 0 IP Background
269 21384 1931910 11 0.07% 0.06% 0.07% 0 PPP manager
271 116 60672 1 0.07% 0.00% 0.00% 0 Multilink PPP
23 98400 321 306542 0.00% 0.07% 0.03% 0 AAA high-capacit
=====================
as we see above , we have high "IP Input" about differnece in cpu =67-54=13 % , which is high value process in software .
i follwed the article here :
http://www.cisco.com/c/en/us/support/docs/routers/7500-series-routers/41160-highcpu-ip-input.html
i check and found that my router is fine ,
no arp calls.
no routing loops.
no flapping links.
i checked that my router has cef enabled and no enormous routing protocol updates
i found that i have big differnce between hardware & software process on the router which is 13 %
but when the traffic is more and more , the cpu reach reach 93 % and begin to have drops.
i just want to ask , how can i debug the operations that are done on the cpu processor of the router ???
i mean that if i know that traffic , i can estimate and know the problem that increasing my cpu !!!
another question :
how to debug the packest that has a ttl exceeded 50 or ttl exceeded 100 ?????
i dont wan tto make debug ip packed , because i have a huge traffic and it will let my router hanged due to large debug !!
===============
righ now i will post my router config and some verification:
drvirus#sh running-config
Building configuration...
Current configuration : 12291 bytes
upgrade fpd auto
version 12.4
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no service dhcp
hostname drvirus
boot-start-marker
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T7.bin
boot system flash disk2:c7200p-adventerprisek9-mz.124-24.T8.bin
boot-end-marker
logging message-counter syslog
aaa new-model
aaa group server radius radiusservers
server-private 10..f.f.f auth-port 1812 acct-port 1813 key 7 weifuhjkefkjdbhfjkasbfjka
aaa authentication login adminstaff local
aaa authentication login sdm_vpn_xauth_ml_1 group radius
aaa authentication login ahmad local
aaa authentication ppp vpdn group radiusservers local
aaa authentication ppp drvirus local
aaa authentication ppp vpdn1 local group radiusservers
aaa authentication ppp ddd none
aaa authentication ppp dddd none
aaa authentication ppp anyok none
aaa authorization network default group radius local
aaa authorization network vpdn group radiusservers local
aaa authorization network sdm_vpn_group_ml_1 local
aaa authorization network drvirus local
aaa authorization network vpdn1 local group radiusservers
aaa authorization network ddd none
aaa authorization network anyok none
aaa accounting delay-start
aaa accounting update newinfo periodic 10
aaa accounting network vpdn
action-type start-stop
broadcast
group radiusservers
aaa server radius dynamic-author
client xxxxxxxx
client 10.xxxxxx
client 10.xxxxxxxxx
server-key 7 dihcbsdjkbvcsdhmbvhsdbvsdhmbvsd
auth-type any
aaa session-id common
clock timezone GMT+3 3
no ip subnet-zero
no ip source-route
no ip gratuitous-arps
ip cef
no ip bootp server
ip domain name drvirus
ip name-server x.x.x.x.x
ip name-server 8.8.8.8
login block-for 180 attempts 3 within 60
login quiet-mode access-class telnet
login on-failure log
login on-success log
no ipv6 cef
ipv6 dhcp pool vvv
prefix-delegation pool version6
address prefix 3333::/64
dns-server 4444::1
multilink bundle-name authenticated
vpdn enable
vpdn logging
vpdn logging local
vpdn history failure table-size 50
vpdn-group eeeeeeeeeeee
accept-dialin
protocol l2tp
virtual-template 1
terminate-from hostname qqqqqq
local name rrrrrrr
lcp renegotiation on-mismatch
l2tp tunnel password 7ekfhjjeklfnlenfl
l2tp tunnel timeout no-session 60
ip mtu adjust
username drvirus@!34`!512&$8#$232!^@^FGsdGD privilege 0 password 7 000sdkjhvsdkjvnah94313085g2355091407458E32425D
interface Loopback1
ip address ttttttt 255.255.255.255
interface GigabitEthernet0/1
description ttttttt
ip address 10.60.60.2 255.255.255.0 secondary
ip address 10.200.200.200 255.255.255.0
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/1.4
encapsulation dot1Q 4
ip address ttttttttt 255.255.255.224
interface GigabitEthernet0/1.14
encapsulation dot1Q 14
ip address 192.168.50.3 255.255.255.0
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
ip address 10.160.150.2 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
interface GigabitEthernet0/3
description rrrrrrr
ip address xxxxxxx 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
load-interval 30
duplex full
speed 1000
media-type sfp
negotiation auto
interface Virtual-Template1
ip unnumbered Loopback1
ip tcp adjust-mss 1412
no logging event link-status
peer default ip address pool xxxxx xxxxxx
ppp mtu adaptive
ppp authentication pap vpdn1
ppp authorization vpdn1
ppp accounting vpdn
router eigrp 2
redistribute connected metric 1 2 1 2 1
passive-interface default
no passive-interface GigabitEthernet0/1
network 10.200.200.200 0.0.0.0
no auto-summary
eigrp router-id 2.2.2.2
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.200.200.2
ip route dddddddddd 255.255.255.0 fffffff
ip route ddddddddd 255.255.255.0 ffffff
no ip http server
no ip http secure-server
ip radius source-interface GigabitEthernet0/2
radius-server attribute nas-port format d
radius-server configure-nas
radius-server host ddddddddddd auth-port 1812 acct-port 1813 key 7 dddddddddd
radius-server retransmit 0
radius-server key 7 dddddddddddddddddd
radius-server vsa send cisco-nas-port
radius-server vsa send accounting
radius-server vsa send authentication
control-plane
drvirus#sh ip traffic
IP statistics:
Rcvd: 92454889 total, 5908020 local destination
0 format errors, 94 checksum errors, 3789577 bad hop count
0 unknown protocol, 23360 not a gateway
0 security failures, 0 bad options, 3730347 with options
Opts: 0 end, 0 nop, 0 basic security, 0 loose source route
0 timestamp, 0 extended security, 0 record route
0 stream ID, 0 strict source route, 3730347 alert, 0 cipso, 0 ump
0 other
Frags: 1409002 reassembled, 485 timeouts, 0 couldn't reassemble
4542214 fragmented, 9089659 fragments, 2659413 couldn't fragment
Bcast: 6024 received, 0 sent
Mcast: 56503 received, 31033 sent
Sent: 15839581 generated, 2407203241 forwarded
Drop: 23 encapsulation failed, 0 unresolved, 0 no adjacency
0 no route, 0 unicast RPF, 0 forced drop
0 options denied
Drop: 0 packets with source IP address zero
Drop: 0 packets with internal loop back IP address
0 physical broadcast
ICMP statistics:
Rcvd: 0 format errors, 0 checksum errors, 0 redirects, 4 unreachable
140579 echo, 33742 echo reply, 0 mask requests, 0 mask replies, 0 quench
0 parameter, 0 timestamp, 0 timestamp replies, 0 info request, 0 other
0 irdp solicitations, 0 irdp advertisements
0 time exceeded, 0 info replies
Sent: 0 redirects, 3530 unreachable, 33744 echo, 140579 echo reply
0 mask requests, 0 mask replies, 0 quench, 0 timestamp, 0 timestamp replies
0 info reply, 46795 time exceeded, 0 parameter problem
0 irdp solicitations, 0 irdp advertisements
TCP statistics:
Rcvd: 19285 total, 0 checksum errors, 7 no port
Sent: 39402 total
BGP statistics:
Rcvd: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh, 0 unrecognized
Sent: 0 total, 0 opens, 0 notifications, 0 updates
0 keepalives, 0 route-refresh
IP-EIGRP statistics:
Rcvd: 39154 total
Sent: 39275 total
PIMv2 statistics: Sent/Received
Total: 0/0, 0 checksum errors, 0 format errors
Registers: 0/0 (0 non-rp, 0 non-sm-group), Register Stops: 0/0, Hellos: 0/0
Join/Prunes: 0/0, Asserts: 0/0, grafts: 0/0
Bootstraps: 0/0, Candidate_RP_Advertisements: 0/0
Queue drops: 0
State-Refresh: 0/0
IGMP statistics: Sent/Received
Total: 0/0, Format errors: 0/0, Checksum errors: 0/0
Host Queries: 0/0, Host Reports: 0/0, Host Leaves: 0/0
DVMRP: 0/0, PIM: 0/0
Queue drops: 0
UDP statistics:
Rcvd: 5632168 total, 0 checksum errors, 9605 no port
Sent: 15536481 total, 0 forwarded broadcasts
OSPF statistics:
Rcvd: 0 total, 0 checksum errors
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
Sent: 0 total
0 hello, 0 database desc, 0 link state req
0 link state updates, 0 link state acks
ARP statistics:
Rcvd: 36012 requests, 25 replies, 0 reverse, 0 other
Sent: 3590 requests, 1883 replies (41 proxy), 0 reverse
Drop due to input queue full: 0
drvirus#sh interfaces switching
GigabitEthernet0/1 ffff
Throttle count 0
Drops RP 29334 SP 0
SPD Flushes Fast 183378 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 196591 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 50222652 1410586379 38933488 2377282438
Cache misses 0 - - -
Fast 2501299905 502401799 1732463443 1178236678
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 36178 2170680 3643 233084
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1039 385469 2067 772027
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 2266 138297 6179 370740
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
Interface FastEthernet0/2 is disabled
GigabitEthernet0/2
Throttle count 0
Drops RP 0 SP 0
SPD Flushes Fast 785 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 1900 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 382927 34296776 382540 106683985
Cache misses 0 - - -
Fast 198 31569 0 0
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 104 8008
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1900 114000 1813 108780
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 1030 378010 1031 378377
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
GigabitEthernet0/3 drvirus
Throttle count 0
Drops RP 15 SP 0
SPD Flushes Fast 22435 SSE 0
SPD Aggress Fast 0
SPD Priority Inputs 194236 Drops 0
Protocol IP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 40507058 2970006619 56462488 1872816742
Cache misses 0 - - -
Fast 1758170357 386468928 2449949282 3706868609
Auton/SSE 0 0 0 0
Protocol DEC MOP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 105 8085
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol ARP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 5 300 7 420
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol CDP
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 1034 379478
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
Protocol Other
Switching path Pkts In Chars In Pkts Out Chars Out
Process 0 0 6180 370800
Cache misses 0 - - -
Fast 0 0 0 0
Auton/SSE 0 0 0 0
NOTE: all counts are cumulative and reset only after a reload.
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1644 105280 250040
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1644 105472 256356
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#sh ip route summary
IP routing table name is Default-IP-Routing-Table(0)
IP routing table maximum-paths is 32
Route Source Networks Subnets Overhead Memory (bytes)
connected 1 1645 105344 250192
static 3 0 192 456
eigrp 2 0 0 0 0
internal 5 5860
Total 9 1645 105536 256508
Removing Queue Size 0
drvirus#
ANy help ??????!!!!!

can some one determin if :
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
has a relation to my high cpu
her is agian my cpu process :
drvirus#sh processes cpu sorted
CPU utilization for five seconds: 69%/51%; one minute: 62%; five minutes: 59%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
87 22165548 147317354 150 7.60% 6.54% 5.74% 0 IP Input
16 682988 2637213 258 3.61% 0.70% 0.37% 0 EnvMon
122 9166144 120227216 76 3.30% 2.81% 2.42% 0 L2X Data Daemon
270 484700 4987094 97 0.76% 0.84% 0.86% 0 PPP Events
260 746640 483367 1544 0.30% 0.51% 0.51% 0 L2TP mgmt daemon
112 1082540 228491 4737 0.30% 0.31% 0.31% 0 CEF: IPv4 proces
190 596 755 789 0.30% 0.02% 0.00% 2 SSH Process
279 461184 78909 5844 0.30% 0.39% 0.45% 0 VTEMPLATE Backgr
52 954592 29823 32008 0.30% 0.31% 0.31% 0 Compute load avg
272 53744 2782461 19 0.23% 0.17% 0.16% 0 IPHC Admin
261 513524 428266 1199 0.23% 0.38% 0.37% 0 L2TUN Applicatio
142 31888 35627222 0 0.23% 0.19% 0.20% 0 HQF Shaper Backg
258 570384 1602872 355 0.15% 0.18% 0.17% 0 RADIUS
78 43280 392561 110 0.15% 0.10% 0.08% 0 ACCT Periodic Pr
281 52340 385568 135 0.07% 0.08% 0.09% 0 IP-EIGRP: PDM
40 37300 138153 269 0.07% 0.09% 0.10% 0 Net Background
77 145860 443602 328 0.07% 0.06% 0.07% 0 AAA ACCT Proc
110 31060 53876 576 0.07% 0.03% 0.02% 0 IP RIB Update
45 11868 52400 226 0.07% 0.01% 0.00% 0 IF-MGR control p
115 20164 103667 194 0.07% 0.02% 0.00% 0 PPP IPCP
102 181600 489310 371 0.07% 0.14% 0.15% 0 SSM connection m
143 3148 1461382 2 0.07% 0.01% 0.00% 0 RBSCP Background
80 19488 22128 880 0.07% 0.02% 0.00% 0 CDP Protocol
23 189412 10771 17585 0.00% 0.15% 0.04% 0 AAA high-capacit
22 0 1 0 0.00% 0.00% 0.00% 0 CEF MIB API
21 0 2 0 0.00% 0.00% 0.00% 0 ATM Idle Timer
20 376 153594 2 0.00% 0.00% 0.00% 0 ARP Background
24 0 2 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
25 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager
26 1376 26590 51 0.00% 0.00% 0.00% 0 DDR Timers
31 4 30 133 0.00% 0.00% 0.00% 0 EEM ED Syslog
27 0 5 0 0.00% 0.00% 0.00% 0 Entity MIB API
33 324 147392 2 0.00% 0.00% 0.00% 0 GraphIt
34 0 2 0 0.00% 0.00% 0.00% 0 Dialer event
28 0 2 0 0.00% 0.00% 0.00% 0 Serial Backgroun
36 0 2 0 0.00% 0.00% 0.00% 0 XML Proxy Client

Wifi stops passing traffic on original ipad and ipad 2 running ios 5.0.1

I actually just started having this issue with my Original iPad and my iPad 2. From what I'm seeing is not a loss of signal but a loss of connectivity, they just stop passing traffic. When this is happening its sometimes to both iPads but not always. And both our iPhones do not experience the issue while the iPads are having the problem. (all devices running ios 5 and connected to the same AP). Wired devices also do not have any issues wile this is happening to the iPads.
What I have tried so far:
1. Changing Channels on the AP to a less congested channel (didn't help)
2. Shutting wifi off on ipad, then turning back on, solves issue for a random amount of time, then it happens again
3. Rebooting ipad, sometimes does not help at all until you turn off the radio on the ipad, then back on
I was ready to get a new router/ap but after reading some other comments, this may be an issue with other people.

I have exactly the same issue on my brand new iPad2 running iOS5.
I have also changed the channel, tried different settings, etc. to no avail.
It tends to happen when streaming video - Skype, YouTube. Also during movie downloads.
My pc does not have this problem.
We're you able to find a reliable solution?
Thanks!

Firewall Allow all traffic on lan

Is there a way to make a firewall rule to allow all traffic on en1? I have my ip ranges set to allow all traffic, but I still have to turn the firewall off for DHCP to give IP addresses to new devices on the network.

dtich wrote:
thx dean, yes, i had certainly looked at the log, which shows these entries:
Nov 11 21:49:25 north-knoll-server ipfw[8789]: 65534 Deny UDP 169.254.14.242:138 169.254.255.255:138 in via en0
but i have no idea where 169xxx is, nothing on my lan... if the port is 65534, that's an ftp passive port, tried opening that, doesn't solve the problem. if the port is 138, that's netbios, which would be odd, but i tried opening that too. nothing doing. can't figure it out. and the log really isn't helping too much.
traceroute gives me:
traceroute to 169.254.14.242 (169.254.14.242), 64 hops max, 40 byte packets
1 169.254.14.242 (169.254.14.242) 0.593 ms 0.504 ms 0.195 ms
so, i guess that's some internal address that my router uses or something..?? wacky. i'm out of my depth here.
if i allow 169.254.x.x, i still get no joy.
mean anything else to you?
yeah, 169.254.x.x is part of the zeroconf net address range. (See http://en.wikipedia.org/wiki/Zeroconf for more details)
Not sure why the device in particular is trying port 138 unless it's Windows box maybe? Is en0 on your local network or external?

5505 stops passing traffic with 9.1.3

I have a 5505 setup in my home office. It generally works well but I noticed when I upgraded it to 9.1.2.8 it would stop passing traffic after a few days. I figured this was just the interim release blues and waited until 9.1.3 came out. However, with 9.1.3 the problem is even worse. I'm actually not exactly sure what's going on. Here's what I've noticed:
I get a lot of DNS connections with the "h" flag (H.225 traffic) set. This seems like it might have some relation to the problem:
UDP outside 216.218.130.2:53 inside 192.168.234.146:50705, idle 0:00:18, bytes 534, flags h
I also get these in 9.1.2 (which works fine), but far fewer. When traffic stops passing on my ASA, I notice that I have tons of these connections in 9.1.3.
When traffic stops passing, the ASA itself can no longer get to the Internet. I can't ping my Comcast router (actually in my office, L2 adjacent to ASA). I also have some SLA probes going to the Internet which fail. If I do a clear conn all, then everything starts working again for a while. The BTF (dynamic-filter) feature seems to make it worse. If I remove it (remove dynamic-filter-snoop part) then it takes a lot longer before it stops passing traffic:
policy-map global_policy
class inspection_default
inspect dns dns-ipm dynamic-filter-snoop
What's really strange, is even if I remove all service-policy commands, I still get connections with the "h" flag. I don't believe that should be possible so perhaps a bug?
Ideas?

I have a 5505 setup in my home office. It generally works well but I noticed when I upgraded it to 9.1.2.8 it would stop passing traffic after a few days. I figured this was just the interim release blues and waited until 9.1.3 came out. However, with 9.1.3 the problem is even worse. I'm actually not exactly sure what's going on. Here's what I've noticed:
I get a lot of DNS connections with the "h" flag (H.225 traffic) set. This seems like it might have some relation to the problem:
UDP outside 216.218.130.2:53 inside 192.168.234.146:50705, idle 0:00:18, bytes 534, flags h
I also get these in 9.1.2 (which works fine), but far fewer. When traffic stops passing on my ASA, I notice that I have tons of these connections in 9.1.3.
When traffic stops passing, the ASA itself can no longer get to the Internet. I can't ping my Comcast router (actually in my office, L2 adjacent to ASA). I also have some SLA probes going to the Internet which fail. If I do a clear conn all, then everything starts working again for a while. The BTF (dynamic-filter) feature seems to make it worse. If I remove it (remove dynamic-filter-snoop part) then it takes a lot longer before it stops passing traffic:
policy-map global_policy
class inspection_default
inspect dns dns-ipm dynamic-filter-snoop
What's really strange, is even if I remove all service-policy commands, I still get connections with the "h" flag. I don't believe that should be possible so perhaps a bug?
Ideas?

Music stops abruptly at random times?

Hi all.
New 16Gb 3G iPhone. I listen to music on it quite heavily, so it's on most of the day while I program at my desk at work.
Over the past 2 or 3 days, it has started doing something really annoying. All of a sudden, it will stop playing a song it's in the middle of and the screen goes black.
And that's it. Nothing else happens until I intervene by pressing the menu button. Once I do that, it takes me back to the main menu of the phone, and I have to go into the iPod portion again and start playing the music again, as it totally resets itself.
Anyone else having this problem.
The first time this happened, I figured someone had tried to call me and hung up before I got to it, as it is initially that same sort of hesitation you get momentarily prior to a call coming through.
However, it has happened several times now and definitely isn't for this reason. Although I suspect maybe my mail is trying to sync or it is doing some other routine chore in the background that is causing it to have a problem.

I just bought my iPhone 3g last week, and I noticed last night while taking a walk that the songs stop and start randomly. I turn on music (listening through my head phones) and the song will stop. Then a few seconds later it starts, and plays for a few seconds, then pauses. It's like an invisible hand is doing things, because the play/pause button changes by itself.
Not only is this super annoying, but I don't understand why it only does this with the headphones plugged in (and they're the original iPhone headphones, right out of the box)....it DOES NOT do this when I have it plugged in to my car's aux port.

To stop all scheduling in Business Objects 4.0

Hi
I just want to stop all the scheduled reports to run in Business Objects
Which process should i stop for it ?
Is it Adaptive Job Processor?
This is why i need it
We have migrated our BO from 3.1 to 4.0 in UNIX environment so its a prod parallel environment
and we are going to keep the old production environment running too for a week just to test the new one is fine or no.
But for 4.0 we have new prod environment and new CMS database
Next we are going to get all the data using BO Upgrade Tool
As Unix has complete upgrade it will get all the scheduling info too
Now i don't want the reports to run in our old production environment and new too
So which process should i stop which will only stop the Scheduling and wont impact other part.

Priyanka,
You need to STOP the Adaptive Job Server, this will STOP all scheduling jobs.
Regards,
Ajay

Stops Reading at Random Intervals

hello,
we wrote a program for our hot plate and for some reason it will suddenly stop reading at random intervals and give a result of 0's for heating and stirring. we're not sure why this is? is it a hardware problem or a visa read/buffer problem?
thanks
Attachments:
hotplate.zip ‏384 KB

Please continue in your original thread where you were already being helped.

Switch port in dot1x multi-auth mode stops passing traffic

Dear All,
I am experiencing a problem on a Catalyst 4510 (cat4500-ipbasek9-mz.122-53.SG.bin) with 802.1x configured. Client PCs are connected via a mini desktop switch to a Cat 4510 switched port in multi-auth mode. The configuration of the port follows:
interface GigabitEthernet2/34
switchport mode access
ip arp inspection limit rate 30
authentication host-mode multi-auth
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
dot1x pae authenticator
dot1x timeout tx-period 5
dot1x max-reauth-req 6
spanning-tree portfast
ip verify source vlan dhcp-snooping
end
It happens from time to time that the Cat 4510 port stops passing traffic. Reconnecting the mini switch recovers the communication. Client PCs connected to the mini switch seem to be authorized at the moment when the problem occures. The RADIUS Termination-Action attribute is set to RADIUS-Request. The problem is not present if "authentication periodic" is disabled.
Did anyone experience a simmilar problem? Any advice?
Thanks.
Mirek

We have the same issue on 3750E switch running 12.2.(58)SE

Forwarding all traffic to a new IP

I've got a machine with two NICs in it which is currently acting as a transparent firewall (i.e. just bridge the two NICs and watch traffic). I've added a third NIC and want to send a copy of all traffic that goes through the bridge out through the new NIC to a separate box so I can run an IDS or packet logger on it. How can I do it?
I've tried fighting with various iptables rules but not gotten anywhere.
I've got the daemonlogger script (http://www.snort.org/users/roesch/Site/ … ogger.html) which copies all the traffic on the bridge to the new NIC but I'm stuck with actually sending it out from there.

To move SQL to New IP:
To assign a TCP/IP port number to the SQL Server Database Engine
In SQL Server Configuration Manager, in the console pane, expand SQL Server Network Configuration, expand Protocols for <instance name>, and then double-clickTCP/IP.
In the TCP/IP Properties dialog box, on the IP Addresses tab, several IP addresses appear in the format IP1, IP2,
up to IPAll. One of these is for the IP address of the loopback adapter, 127.0.0.1. Additional IP addresses appear for each IP Address on the computer. Right-click each address, and then click Properties to
identify the IP address that you want to configure.
If the TCP Dynamic Ports dialog box contains 0, indicating the Database Engine is listening on dynamic ports, delete the 0.
In the IPn Properties area box, in the TCP Port box, type the port number you want this IP address to listen on,
and then click OK.
In the console pane, click SQL Server Services.
In the details pane, right-click SQL Server (<instance name>) and then click Restart, to stop and restart SQL Server.
https://msdn.microsoft.com/en-IN/library/ms177440.aspx
Regards, Pradyothana DP. Please Mark This As Answer if it solved your issue. Please Mark This As Helpful if it helps to solve your issue. ========================================================== http://www.dbainhouse.blogspot.in/

Music spontaneously starts, stops, stutters at random and I'm not even using that app. Repeated attempts to pause the song and close the app have no affect. Just keeps popping on and off randomly no matter what I'm doing at the time.

How do I eliminate this glitch? Music spontaneously starts, stops, stutters at random and I'm not even using that app. Repeated attempts to pause the song and close the app have no affect. Just keeps popping on and off randomly no matter what I'm doing at the time. I tried double-clicking the Home button which brings up all of the active apps, touched and held the Music icon until all the icons started wiggling, tapped the Close icon in the upper left corner of the Music app to close the app completely, but the app is still open and still randomly stuttering. I did notice that the play button icon flashes in the upper right corner of the screen when this happens and it appears and disappears in concurrence with the Music app stuttering. When the music starts, the icon appears and when it stops, the icon disappears again. When the music stutters on and off, the icon appears and disappears rapidly and in sync with that random glitch. This just started today for no apparent reason. I turned the iPad off, waited 30 seconds and turned it back on. As soon as it was finished starting up, the same music glitch began again immediately. I'm using iOS 6.1.3.

Well, no one seems to have any answers or ideas for me, I'll update what I've been able to accomplish.
I reloaded all 14 disks in the time frame of watching Lord of the Rings on Fri. nite.
Funny thing is, the first disk pulled the info from the online store! Hooray!
Wait-then all the next 13 could find no information online...what the heck is up with that? So I MANUALLY assign each disk a new track # to co-inside with each disk, spent about 2 hours doing that.
But still, itunes tells me my playlist is too large, there's not enough space on the ipod. so I unchecked 1 1/2 disks (I'd listen to 1/2 of disk 1 previously) and voila! there's my ipod full of my book. Finally. But what a lot of bother just to keep things in order!

No internet access when "Send All Traffic" VPN Checked

Hi Ladies and Gents
Wonder if you can help me. These past few days I have been setting up a VPN on my DD-WRT enabled router. I have successfully accomplished such task, however when I'm connected to the VPN on my phone my public IP address does not change, after doing some reading I believe that is because "Send All Traffic" is unchecked in the VPN profile, but when I check "Send All Traffic" I get no internet access what so ever.
Any advice/input/solution to this would be greatly appreciated.
Cheers
Cameron

Cammy1230 wrote:
when I'm connected to the VPN on my phone my public IP address does not
it's not supposed to.

Stop all Oracle Services

I am upgrading/patching my test 10g database. While upgrading it ask you stop all oracle services in order to continue the upgrade. I did that but it is still asking to stop all oracle services. Now what do I do, anybody have experience with that.

First, make sure you don't have any thing automatically started, and don't use even sqlplus, as a client it will load several dll's and when the upgrade process starts it will mark several dll's as being used.
I've been working with win2003 several upgrade processes, I don't know exactly why, but several dll's are still marked as being used, even if the host was restarted with the service set to manual start. The exact list of dlls that are in this situation correspond to those used by an oracle client.
The workaround I found for my specific case was to rename the dll's and let OUI to write the new version.

Router stops all traffic randomly, why?

Similar Messages

Maybe you are looking for